light AUDI A8 2018 Owners Manual

u. co ..... N
" N ..... 0 0 :c ' also blinks for approximately one minutes each
time the ignition is switched on . The tire pressure
monitoring system cannot be selected in the In­
fotainment system. The following are examples
of situations that could cause a malfunction:
- If the message appears at the end of the adap­
tation phase, the system cannot detect the
wheels installed on the vehicle . This may result
from one or more wheels being installed with­ out wheel sensors or with incompatible wheel
sensors .
- A wheel sensor or another component has
failed .
- Using snow chains can affect the function of
the system because of the shielding effect of
the chains .
- The tire pressure monitoring system is not
available due to a malfunction .
- Transmitters with the same frequency, such as
headphones or remote-controlled devices, may
cause a temporary system malfunction due to
the strong e lectromagnetic field .
The
@m indicator light turns off once the Tire
Pressure Monitoring System is available again . If
you cannot correct the malfunction and the
mm
indicator light stays on, drive immediately to an
author ized Audi dealer or author ized Audi Service
F acility to have the malfunction repaired.
Wheels
305

Care and cleaning
Care and cleaning
General information
Regular, proper care helps to maintain your vehi­
cle's value. It can also be a requirement when
submitting warranty claims for corrosion damage
and paint defects on the body.
The necessary care products can be obtained
from an authorized Audi dea ler or authorized
Audi Service Facility. Read and follow the instruc ­
tions for use on the packaging.
A WARNING
-Using cleaning and care products incorrectly
can be dangerous to your health.
- Always store clean ing and care products out
of reach of children to reduce the r isk of poi­
sonin g.
@ For the sake of the environment
- Preferab ly purchase environmenta lly-friend­
l y cleaning products.
- Do not dispose of leftover cleaning and care
products with household trash.
Car washes
The longer that deposits such as insects, bird
droppings, tree sap or road salt remain on the ve­
h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
increase the damaging effect.
Before washing, r inse
off heavy deposits with
p lenty of water.
Stubborn deposits such as bird droppings or tree
sap are best removed with plenty of water and a microfiber cloth.
A lso, wash the underside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your veh icle w ith a pressure wash­
er , al ways fo llow the operating instructions pro­
vided with the press ure washer. This is especially
important in regard to the pressure and spraying
distance. Do not aim the spray directly at the
306
seals on the side windows, doors, lids or the sun­
roof* or at tires, rubber hoses, insulating materi ­
a l, sensors* or camera lenses* . Keep a distance of
at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washer.
Never use cone nozz les or high pressure nozzles.
The water temperature must not be above 140 °F
(60 °C) .
Automatic car washes
Spray off the vehicle before washing.
Make sure that the windows and roof* are closed
and the windshie ld wipers are
off . Follow instruc ­
tions from the car wash operator, especially if
there are accessories attached to your vehicle.
If possible, use car washes that do not have
brushes.
Only use car washes where the vehicle remains
stationary and the washing equipmen t moves
around the vehicle when washing and drying. Car
washes that move the vehicle t hrough the car
wash using a chain are not recommended .
Washing by hand
Clean the vehicl e starting from the top and work­
ing down using a soft sponge or cleaning brush.
Use solvent -free cleaning products.
Washing vehicles with matte finish paint by
hand
To avoid damaging the paint when washing, first
remove dust and large particles from your vehi ­
cle. Insects, grease spots and fingerprints are
best removed with a special cleaner for matte
finish paint .
Apply t he product using a microfiber cloth. To
avoid damaging the paint surface, do not use too
much pressure.
Rinse t he ve hicle thoroughly with wate r. Then
clean using a neutral shampoo and a soft micro ­
fiber clot h.
R inse the vehicl e thoroughly again and let it air
dry. Remove any water residue using a chamois.
..,..

u. co .... N
" N .... 0 0 :c ' & WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
-To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the braking effect may be delayed due to moisture on the
brake rotors or ice in the winter . This in­
creases the risk of an accident. The brakes
must be dried first with a few careful brake
applications.
@ Note
-If you wash the vehicle in an automatic car
wash, you must fold the exterior mirrors in
to reduce the risk of damage to the mirrors.
Power folding exterior mirrors* must only
be folded in and out using the power folding
function.
-To reduce the risk of paint damage, do not
wash the vehicle in direct sunlight.
-
Care and cleaning
-To reduce the risk of damage, do not wash
the power top with a pressure washer.
-To reduce the risk of damage to the surface,
do not use insect removing sponges, kitchen
sponges or similar items.
-Matte finish painted vehicle components:
-To reduce the risk of damage to the sur-
face, do not use polishing agents or hard
wax.
-Never use protective wax. It can destroy
the matte finish effect .
-Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint. The paint could be damaged
when the stickers or magnets are re­
moved .
@ For the sake of the environment
Only wash the vehicle in facilities specially de­
signed for that purpose . This will reduce the
risk of dirty water contaminated with oil from
entering the sewer system.
Cleaning and care information
When cleaning and caring for individual vehicle
components, refer to the following tables. The
information contained there is simply recom­
mendations. For questions or for components that are
not listed, consult an authorized Audi
dealer or authorized Audi Service Facility. Also
follow the information found
in~.&. -
Exterior cleaning
Component Situation Solution
Windshield wiper
Deposits ~ page 51
blades
Headlights/
Deposits Soft sponge with a
mild soap solutiona)
Tail lights
Sensors/
Deposits Sensors: soft cloth with solvent-free cleaning solution
camera lenses Camera lenses: soft cloth with alcohol-free cleaning solu-
tion
Snow/ice Hand brush/solvent-free de-icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
307
...

u. co .... N
" N .... 0 0 :c ' Care and cleaning
Component Situation Solution
Te xtiles
Deposits adhering to Vacuum cleaner
artificial leather, the surface
Alcantara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
O il-based deposits Apply a m ild soap solution
al, blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such
Specia l stain remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mi ld soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc .
Natural leather Fresh stains Cotton cloth with a mi
ld soap solution a>
Water-based deposits Fresh stains : absorbent cloth
such as coffee, tea, dried stains: stain remover suitable for leather
b lood , etc.
Oi l-based deposits Fresh sta ins: absorbent cloth and stain remover suitable
such as oil, make-up, for leather
etc . dried stains: oil cleaning spray
Special deposits such Spot
remover suitable for leather
as ink, nail polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply conditioning cream that protects from
light and penetrates into the material. Use specially-c ol-
ored conditioning cream, if necessary .
Refrigerator Dust and dirt Clean the ventilation openings in the luggage compart-
ment
Deposits Lukewarm
water, mild soap solution if
necessarya>, then
dry
Defrosting Empty the refrige rato r, switch it off and let it thaw with
the door open, t hen dry
Carbon parts Deposits clean the same way as plast ic parts
• > Mi ld s oap so lution: maxim um two tablesp oon s of neu tra l soap in 1 quar t (1 lite r) of wat er
A WARNING
Th e windsh ie ld may not be treated with wa­
ter-repelling windshi eld coating agents. Un­
favorable conditions such as wetness, dark­
ness, or lo w sun can result in increased glare.
Wiper blade chatter is also possible.
@ Note
-Headlights/tail lights
-
- Never clean headlights or tail lights with a
dry cloth or sponge.
- Do not use any cleaning product that con­
tains alcoho l, because they could cause
cracks to form .
-Wheels
- Never use any paint polish or other abra-
sive materials.
309

Care and cleaning
- Damage to the protective layer on the rims such as stone chips or scratches must
be repaired immediately.
- Sensors/camera lenses
- Never use warm or hot water to remove
snow or ice from the camera lens . This
could cause the lens to crack .
- Never use abrasive cleaning materials or
alcohol to clean the camera lens . This
could cause scratches and cracks .
-Door windows
- Remove snow and ice on windows and ex-
terior mirrors with a plastic scraper. To
avoid scratches, move the scraper only in
one direction and not back and forth.
- Never remove snow or ice from door win­
dows and mirrors using warm or hot water
because this could cause cracks to form.
- To avoid damage to the rear window de­
fogger, do not apply any stickers on the heating wires on the inside of the window.
- Decorative parts/trim
- Never use chrome care or cleaning prod-
ucts .
-Paint
-To reduce the risk of scratches, the vehicle
must be free of dirt and dust before pol­
ishing or waxing.
- To prevent paint damage, do not polish or
wax the vehicle in direct sunlight.
- To reduce the risk of paint damage, do not
polish away rust spots .
- Remove cosmetics and sunscreen immedi­
ately
-these could damage the paint.
- Displays
-To avoid scratches, do not use dry cleaning
methods on displays.
-Controls
- Make sure that no fluids enter the con-
trols, because this could cause damage.
-Safety belts
- Do not remove the safety belts to clean
them.
- Never clean safety belts or their compo­
nents chemically or with corrosive fluids
or solvents and never allow sharp objects
to come into contact with the safety belts.
310
This could cause damage to the belt web­
bing.
- If there is damage to the webbing, the
connections, the retractors or the buckles,
have them replaced by an authorized Audi
dealer or authorized Audi Service Facility .
-Textiles/artificial leather/ Alcantara
- Never treat artificial leather/Alcantara
with leather care products, solvents, floor
polish, shoe polish, spot remove or similar
products.
- Have a specialist remove stubborn stains
to prevent damage .
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the seat .
- Objects with sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Open hook and loop fasteners, for exam ­
ple on clothing, can damage seat covers .
Make sure hook and loop fasteners are
closed.
- Natural leather
- Never treat leather with solvents, floor
polish, shoe polish, spot remover or simi­
lar products.
- Objects with sharp edges, such as zippers
or rivets on clothing or belts, can cause
damage to the surface.
- Never use steam cleaners, brushes, hard
sponges, etc. when cleaning.
- Do not turn on the seat heating* to dry the
seat.
- To help prevent the leather from fading,
do not leave the vehicle in direct sunlight
for long periods of time. If leaving the ve­
hicle parked for long periods of time, you
should cover the leather to protect it from
direct sunlight.
- Refrigerator
- Do not try to speed up the defrosting
process by applying heat.
- To help prevent health risks or damage to
the refrigerator, do not use any abrasive
.,..

Emergency assistance
6. Remove the wheel with the flat tire and then
install
the spare r::!> page 318.
7. Tighten all wheel bo lts light ly .
8. Lower the veh icle w ith the jack.
9. Use the wheel bolt wrench and firmly t ighten
a ll whee l bolts
r::!> page 315 .
10 .
Replace the decorative wheel cover* .
11. D eactivate the vehi cle jack mode in the MMI:
ICAR I fu nction bu tton > Car systems con trol
b utt on
> Servicing & c heck s > Air susp .: ja ck
mode > Off.
The vehicle jack mode switches off a utomat ically
at speeds above
10 k m/ h.
_& WARNING
Alw ays read and fo llow all WARNI NGS and in ­
formation
c::> .&. in AB: Raising the vehicle on
poge316an d
¢page 319.
After changing a wheel
A wheel change is not complete without the do ­
ing the following.
• A lway s store the vehicle tool kit, the jack* a nd
t he repl aced t ire in the luggage compartment
r::!:> poge 213.
• Check the tire pre ssure on the spare whee l im ­
med iate ly after mount ing it.
• As soon as possible, have th e tightening tor­
ques
on all wheel bolts checked with a torque
wrench. The correct tightening torque is
90 ft
lb
(120 Nm) .
• Have the fla t tire replaced as soon as possible .
(D Tips
- If you notice that the whee l bolts are cor­
r oded and diffic ult to t urn wh ile cha nging a
tire, they should be rep laced before you
c hec k th e tighte ning torque .
- Drive a t reduced speed until you have the
tightening torques c hec ke d .
- After changi ng a wheel, the ti re pressure in
a ll four tires must be chec ked/corrected and
the tire pr ess ure mon itoring indicato r mus t
be store d in t he MM I
r::!:> page 302 .
314 Decorative wheel covers
App
lies to : vehicles with decorative w heel covers
The decorative wheel covers must be removed
first to access the wheel bolts.
F ig. 273 Changing a whee l: Remov ing t he whe el cover
Removing
• Insert the hook (p rovided w ith the vehicle tool
kit) i n the hole in the wheel hu b cover .
• Pull off the decorative wheel cover r::!:> fig. 273 .
Wheels with wheel bolt caps
Applies to: vehicles with w heel bolts with caps
The cops must be removed first from the wheel
bolts before the bolts con be unscrewed.
Fi g. 274 Chang ing a wheel: remov ing the w heel bo lt caps
Removing
• Push the plastic clip (prov ided with the vehicle
tool k it) over the whee l bolt cap until the inner
reta iners on the clip a lign with t he edge of the
cover.
• Remove the cap with t he plastic clip (veh icle
t oo l kit )
r::!> fig. 274.
Refitt ing
• Place the caps over the whee l bolts and push
them back on .

Emergency assistance
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig. 28 0 Changing a wheel: using the screw driver handl e
(wit h th e blade re m oved) to turn the bol ts
F ig . 2 81 Changing a wheel: alignment p in inside t he top
hole
Afte r you have loosened a ll w heel bo lts and
raised t he vehi cle off the ground, remove and re­
p lace the whee l as fo llows:
Removing the wheel
• U se the hexagonal so cket in the screwdriver
handle
t o comple tely remove the topmost
whee l bolt and set it aside on a
clean surfa ce
¢ fig. 280 .
• Screw the th readed end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole¢
fig. 2a1 1>.
• The n remove the other whee l bolts as desc ribed
above.
• Takeoff th e wheel leav ing the a lignm ent pin in
the bolt ho le
¢ 0 .
l) Applies to vehicles with ceram ic brake rotors*: Use a sec­
ond alignment
pin* (stored in th e spa re whee l well mo ld­
ing) for the lower ho le, fo llowing t he descr iption for the
first alignment pin .
318
Putting on the spare wheel
• Lif t the sp are whee l and caref ully slide it over
t he alignment p in to guide it in place
¢ (D .
• Use the hexagonal socket in the sc rewdr iver
ha nd le to screw in and tighten a ll w heel bolts
slightly.
• Remove the alignment pin and insert and tight­
en the remaining w heel bo lt slight ly like the
rest.
• Tu rn the jack hand le co unte r-clockw ise to lowe r
t he vehicle unt il t he jac k is f ully re leased.
• Use the w heel bo lt wren ch to tighten a ll wheel
bolts fi rm ly¢
p age 315. Tighten them cross­
wise,
from one bo lt to the (a pprox imately) op ­
posite one, to keep the whee l centered.
([» Note
When remov ing o r installin g the wheel, the
rim co uld hit the brake rotor/ce ramic brake
r otor * and damage t he rotor . Work carefully
and have a second person he lp you.
(D Tips
N eve r use the he xagonal socket in the han dle
of the sc rew drive r to loosen or t ig hten the
whee l bolts.
- Pull the reversible blade from the screwdr iv­
er before yo u use t he hexagona l soc ket in
t h e handle to t urn the whee l bolts.
- When mounti ng tires with
unidirectional
tread design
make sure the tread pattern is
pointed the right
way¢ page 319.
- The wheel bolts sho uld be clean and easy to
t u rn. Check for dirt and corrosion on the
mating surfaces of both the wheel and t he
hub. Remove all dirt from these s urfaces be­
fore remounti ng the whee l.

Fuses and bulbs
Fuses and bulbs
Electrical fuses
Changing fuses
A fuse that has blown will have metal strips that have burned through .
Fig. 284 Driver side of the cockp it: fuse panel cover
1
•
Fig. 285 Luggage compartment: fuse panel cover
The fuses are located on front left and right of
the cockpit and behind the trim on the right side
of the luggage compartment.
.. Switch the ignition and all electrical equipment
off.
.. Check the following table to see which fuse be­
longs to the equipment .
.. Remove the cover c::> fig. 284 or c::> fig. 285 .
.. Remove the colored plastic clip from the fuse
panel, if necessary
<=:>page 323 , fig. 286. You
can dispose of the plastic clip .
.. Remove the clamp from the rear side of the
cover
c::> fig. 284 .
.. Remove the fuse using the clamp .
.. Replace the blown fuse only with an identical
new one .
.. Install the cover.
322
Fuse color identification
Color Current rating
in amps
Black 1
Purple 3
Light brown 5
Brown 7.5
Red 10
Blue 15
Yellow 20
White or transparent 25
Green 30
Orange 40
A WARNING
-
Do not repair fuses and never replace a blown
fuse with one that has a higher amp rating.
This can cause damage to the electrical sys­
tem and a fire.
(D Note
If a new fuse burns out again shortly after you
have installed it, have the electrical system
checked as soon as possible by an authorized
Audi dealer or authorized Audi Service Fac ili­
ty .
(!) Tips
-The following table does not list fuse loca­
tions that are not used .
- Some of the equipment listed in the follow­
ing tables applies only to certain model ver­
sions or certain optional equipment.

lL t:0 ....
'"" ......
'"" .... 0 0 :c ' Driver's side cockpit fuse assignment
Fig. 286 Drive r side cockpit: fuse panel with plastic bracket
Fuse panel @ (brown)
No. Equipment
1 Light switch
2 Eme rgency start coil (driver iden tification)
3 Left rear door control module
4 Head-up display
5 Horn
6 Interior lights (headliner)
Steering column lever, multifunction
8 steer ing whee l controls, steering wheel
heating
10 Powe r steering column adjustment
11 Driver door control module
12 Diagnostic con nector, light/rain sensor
14 Power steering column adjustment
lS Power steering, A/C compressor
16 Brake booster
Fuse panel © (black)
No. Equipment
1 Front seat heating
2 Windshield wipers
Fuses and bulbs
Fuse panel © (black)
3 Front exterior lighting
4 Sliding/tilting sunroof
5 Driver power window
6 Dr iver 's seat (pne umat ic)
7 Panorama glass roof
8 Dynamic steering
9 Front exterior lighting
10 Windshield/headlight washer system
11 Left rear power window
12 Panorama glass roof
Front passenger side cockpit fuse
assignment
Fig. 287 Fro nt passe nge r side cockp it: fuse panel with
plastic bracket
Fuse panel @ (black)
No. Equipment
1 Anti-theft alarm system
2 Transmission contro l module
3 Front climate control fan
4 Engine s upply
6 Engine control module
7 Front passenger door control module
323

Fuses and bulbs
Fuse panel@ (black ) Fuse panel@ (black)
8 Front passenger power window 11 Right rear power window
9 ESC con trol module 12 Front passenger's seat (pne umatic)
10 E
SC control module
Luggage compartment fuse assignment
F ig . 28 8 Luggage co mpar tment : fuse panel w it h plastic bracket
Fuse panel @ (black) Fuse panel@ (black)
No. Equipment
10 Rear seat heat
ing, refrigerator, rearv iew
1 ESC b
utton , data logger, d iagnost ic con -
nector, BCM - 1, adaptive lig ht mir
ror
1 1 Electromechanical steering
2 Network ing gateway 12 Selec tor lever, BCM-2 vol tage
3 Adaptive air suspension
13 Side assist
4 Park ing a id 14 E ngine contro l module
5 Steer
ing column lever
15 Starter
6 S usp ension contro l system senso r
7 Belt tensioners, airbag control mod ule 16
L
eft head light (he adlights w it h adap tive
li ght)/head light range co ntr ol
Heated w asher flu id no zz les, Home link
8 (garage doo r opener), night vision system
cont rol mod ule, sport differe ntia l, ionizer
9
Electromecha nica l par king brake cont rol
modu le
Fuse panel ® (red)
No . Equipment
1 Left reversible belt tensioner
2 R
ight revers ible belt tensioner
324