check engine AUDI A8 2018 User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 2018, Model line: A8, Model: AUDI A8 2018Pages: 356, PDF Size: 54.71 MB
Page 78 of 356

Driving
-If physica l limitations prevent you from sit
t ing 10 in (25 cm) or more from the steer
ing wheel, check with your authorized Audi
dealer to see if adaptive equ ipment is avail
able .
-If the steering wheel is aligned with your
face, the supp lemental driver's airbag can
not prov ide as m uch protection in an acci
dent. A lways make s ure that the steering
wheel is aligned w ith your che st.
-Always hold the steer ing whee l with your
hands a t the 9 o' clock and 3 o'clock pos i
t ions to reduce the ris k of person al injury if
the driver 's airbag deploys.
-Never hold the s teer ing whee l at the 1 2
o'clock pos it io n or w ith your ha nds inside
the steering wheel rim or on the steer ing
wheel hub . Holdi ng the steering whee l the
wrong way can cause serious injuries to the hands, arms and head i f the driver's airbag
deploys.
Entry assistance
Easy seat entry makes it easier to enter and exit
the vehicle by adjusting the steering column au
tomatically.
• In the Infotainment system, select the ! CARI
funct ion b utton > Car systems contro l button >
Vehicle settings > Seats > Drive r's seat > Easy
seat entry > On .
When easy seat entry is switched on, the stee ring
column goes back up into the park position when
the ignition is switched off. After entering the ve
h icle, the steering co lumn returns to the stored
position once the ignition is sw itched on .
76
Starting and stopping
the engine
Starting the engine
The ! START ENGINE S T OPI button switches the
ignition on and starts the engine.
Fi g. 90 Ce nter conso le: STAR T ENGINE S TOP but ton
Switching the ignition on /off
• To switch t he ign it ion on or off, press the
! S TAR T ENGINE STOPI button . Do not press the
brake pedal while do ing this.
St arting the engine
• Press the brake pedal¢ &_.
• Press the I START ENGINE STOP I button
¢ fig. 90 . The eng ine will start .
If the engine does not start immediately, the
start ing procedure stops automat ica lly after a
sho rt time . Repeat the sta rting process .
Start/Stop syst em
See the information in ¢ page 78, Start/Stop
system.
A WARNING
To reduce the risk of poison ing, never allow
the eng ine to run in co nfined spaces .
(D Note
Avoid high engine spee d, full throttle, and
h eavy engine load if the engine has not
reached operat ing temperat ure yet . You could
-
damage the eng ine. .,..
Page 81 of 356

lL t:0 ....
"' " "' .... 0 0 :c '
cannot steer and brake as you usually
would, th is could lead to accidents and ser i
ous injuries .
- To reduce the risk of injuries, make sure that
the Start/Stop system is turned off when
working in the engine compartment
i=> page80 .
(D Note
Always switch the Start/Stop system off when
driving through water
i::> page 80.
Starting/stopping the engine
App lies to: ve hicles with Start/Stop system
Fig. 92 Instrument cluste r: eng ine sw itched o ff (stop
p hase)
~ S low the vehicle to a stop us ing the brake and
keep pressing the brake pedal. The engine w il l
switch off. The
II indicator light appears in the
informa tion line in the instrument cluster dis
play.
~ When you take your foot off the brake peda l,
the engine restarts. The indicator lig ht turns
off .
Additional information
The engine w ill switch off in the P, D, N and S po
sitions as we ll as in manual mode . In the P posi
tion, the engine will also remain off if you take
your foot off the brake pedal. The engine starts
again when you se lect another selector lever po
sition and take your foot off the brake pedal.
I f you select the R pos ition during a Stop phase ,
the engine will start again.
Shift from D to P quickly to p revent the engine
from star ting unintentionally when shifting
through R .
Drivi ng
You can de termine for yourse lf if the engine w ill
stop or not by reducing or increasing the amount
of force you use to press the brake pedal. For ex
amp le, if you only lightly press on the brake ped
al in stop-and-go traffic or when turning, the en
gine will not switch off when the vehicle is sta
t io nary . As soon as you press the brake down
harder, the engine w ill switch off .
(D Tips
-Press the brake pedal during a Stop phase
t o keep the vehicle from rolling .
- The ignit ion w ill turn off if you press the
! S T ART ENGINE STOPI button du ring a stop
phase.
General information
Applies to: vehicles w ith Start/Stop system
The standard Start/Stop mode can be canceled
for various system-related reasons.
Eng ine doe s not switch off
Before each stop phase, the system checks if cer
tain conditions have been met . If the
r,J indica
tor light appears in the instrument cluster dis
play, the eng ine will not be stopped, for example
in the following situations:
- The engine has not reached the minimum re
quired temperature for Start/Stop mode.
- T he interior temperature selected by the cli-
mate control system has not been reached.
- The outside temperature is extremely high/low.
-The winds hie ld is being defrosted
~ page 71.
-The parking sys tem* is switched on .
- The vehicle battery cha rge level is too low .
- The steering wheel is tu rned at a sha rp angle or
is moving.
- After engaging the reve rse gear .
- On sharp incl ines.
Eng ine automatically restarts
T he standard Start/Stop mode wi ll be canceled
during a stop phase in the following situat ions .
The eng ine restarts without any action by the
driver .
79
Page 92 of 356

Trailer towing
Trailer load distribution
Be sure the load in the trailer is held securely in
p la ce to prevent it from shifting forward, back
ward or sideways .
Never allow a passenger to ride in a trailer~&.
in Driving instructions on page 91.
Engine cooling system
Towing a trailer makes the engine work harder . It
is important that the coo ling system's perform
ance is up to t he additional load. Make sure that
the cooling system has eno ugh fluid .
Tire pressure
When tow ing a tra iler, inflate the tires of your
veh icle to the tire pressure listed under "Full
load " on the label
~ page 293. Inflate trailer
tires to trailer and tir e ma nufactu rers' specifica
tions.
Lights
Check to make sure both vehicle and trailer lights
are working properly .
Safety chains
Be sure trailer safety chains are proper ly connect
ed from the trailer to the hitch on the vehicle.
Leave enough slack in the chains to permit turn
ing corners . When you install safety cha ins, make
sure they w ill not drag on the road when you are
driving.
The chains should cross under the trailer tongue
to prevent it from dropping in case of separation
from the hitch .
Adjusting the Audi drive select
Make sure the vehicle is on a level surface before
hitching up the trailer and before adjust ing the
tongue we ight. The vehicle must be in
auto or
comfort driving mode and not ra ised
~ page 111, ~0 .
Make sure that the vehicle is lowered. In Info
tainment, select:
ICARI function butto n> Lower
control button.
90
If you must drive under poor road conditions, you
can raise the ve hicle
after coupling the trailer or
after adjust ing the tongue we ight ~ page 113.
@ Note
-Changes in temperature or load can aff ect
the height of the vehicle .
-Always select auto or comfort mode. Other
wise, the tong ue load specified for your ve
hicle will no longer be applicab le .
Driving instructions
Driving with a trailer always requires extra care
and consideration.
Weight distribution
Towing a loaded trailer with an empty car results
in a hig hly unstable distribution of we ight. If th is
cannot be avoided, drive at very low speeds only
to avoid t he risk of losing steering contro l.
A "balanced" rig is eas ier to operate and control.
This means that the tow vehicle s hould be loaded
to
the extent possible and permissib le, w hil e
keeping the trailer as light as possible under the
circumstances. Whenever possible, transfer
some cargo to the luggage compartment of the
tow veh icle while observing tongue load require
ments and vehicle loading considerations.
Speed
The higher the speed, the more difficu lt it be
comes for the driver to control the rig . Do not
drive at the maximum permissible speed. Reduce
your speed even more if load, weather or wind cond it ions are unfavorable - particularly whe n
go ing down hill.
Reduce vehicle speed
immediately if the trailer
shows the slightest sign of sway ing.
Do not try
to stop the swaying by accelerating.
Observe speed limits. In some areas, speeds for
vehicles towing trailers are lower than for regular
vehicles.
A lways apply brakes early. When driving down
hill, shift into a lower gear to use the engine
braking effect to slow the vehicle. Use of the
brakes alone can cause them to overheat and fail.
ll-
Page 132 of 356

Intellig ent T echn olo gy
- New brake pads do not achieve their full
braking effect during the first 250 mi
(400 km). They must be "broken in" first.
However, you can compensate for the
sl ightly reduced brak ing force by pressing
firmly on the brake pedal. Avoid heavy brak
i ng dur ing t he break- in per iod.
- Certa in weather and operat ing cond it ions
such as dr iv ing through water, driving in
heavy ra in or driving after washing your ve
hicle can impair the effectiveness of the
brakes . In the winter, ice may build up on
the brake pads, rotors and drums . Check
these components by braking carefu lly. Ap
plying the brakes carefully severa l times
dr ies the brakes and removes ice bu ild-up.
- The effic iency of the brakes can also be im
paired by driving for long stretches on roads
covered w ith salt w ithout using the brakes.
You can remove salt deposits from the brake rotors and pads by carefully applying
the b rakes severa l t imes .
- If the front spo iler is damaged or you install
another spoiler, make sure the front wheel
bra kes are vent ilated properly. Otherwise,
the brake system could ove rheat, w hich re
duces the ir effectiveness.
- Failure of a b rake circuit impa irs b raking
perfo rmance, which inc reases brak ing dis
tance . Avoid driving the vehicle and have it
towed it to the nearest authorized Audi
dealer or authorized Audi Service Facility .
- If the brake booster is not working, you will
have to press m uch harder on the brake
peda l to compensate for the lack of the
booster.
@ Note
- Never let the brakes " rub" by pressing the
pedal light ly when braking is not actually
necessary. This causes the brakes to over
heat and increases braking distance and
causes wear.
- Before driving downhill a long distance on a
steep hill, decrease your speed and select a l ower gear. This makes use of the engine
braking effect and relieves the brakes. If
130
you need to brake add itiona lly, brake in in
terva ls and not continuous ly .
(D Tips
- If the bra ke boos ter is not wor king, you
must press the brake peda l with much more
force than normal.
- If you retrof it your vehicle with a front spoi l
er, wheel covers or simi lar items, make sure
that the air flow to the front wheels is not interrupted. Otherwise the brake system
can become too hot.
Electromechanical
steering, dynamic
steering
The electromechonicol steering supports the
driver's steering movements.
Power steering adapts electronically based on
the vehicle speed .
Indicator lights and messages
• Do not drive vehi cle: S tee rin g defect ive
If this indicator light turns on and stays on and
th is message appears, the power steering may
have failed .
Stop the vehicle in a safe location as soon as pos
s ible. Do
not conti nue driving. See an authorized
Audi dealer or authorized Audi Service Fac il ity for
ass istance.
l;rfl St ee ring: System faul t You ca n cont inue
dr ivi ng
If the indicator light turns on and the message
appears, the steering wheel may be more diffi
cu lt to move or more sensitive than usual. The
steering wheel may also be at an angle when driv ing stra ight .
Drive slowly to an authorized Audi dea ler or au
thori zed Audi Serv ice Facility to have the mal
funct io n corrected.
'-r-ij Dynamic stee ring: Init ializing
If the indicato r light is blinking and this message
appears, dynamic steering* is being initialized.
IJ>-
Page 197 of 356

u.
The last selected menu is displayed when it is
switched on.
When the ignition is switched off, a message in
d icat ing that the RSE is in standby mode appears
in the left or right RSE display. The RSE switches
off automatically if you do not press the left or
right On/Off knob while the system is in standby
mode.
(D Tips
- The RSE switches off automatically if the
engine is not running and the vehicle bat
tery is low.
Symbols
Applies to: vehicles with Rear Seat Enter tainment
Fig. 203 RSE display symbols
Symbol/Description Explanation
Rear Seat Entertainment
- If you cannot switch the RSE on again, check
the parental control settings in the MMI
¢page 197.
Adjusting the volume
Applies to: vehicles with Rear Seat Entertainment
.,. Increasing or decreasing the volume: turn the
On/Off knob to the right or left .
.,. Muting : press the On/Off knob brief ly.
.,. Unmuting: press the On/Off knob briefly or
turn the On/Off knob to the right .
(D Tips
Volume that is too high or too low is auto
matically adjusted to a preset level when the
RSE is switched on.
CD ~ Active media source
0 Headphones Aud
io output through headphones that are wireless or connected
by a cable
® Speaker Audio output through the vehicle's audio system
@ Importing process Copy audio/video files to the Jukebox ¢
page 183
® Time Set time
® Parental control Parental control is switched on¢ page 197
0 L/R Display for RSE when RSE control panel is act ive
@ Tips
~ A headphone or speaker symbol that is
~ crossed out@/@ ¢ fig. 203 indicates that
...... o the active audio/video source is muted. 0 :c '
Page 270 of 356

Checking and Filling
Checking and Filling
Gasoline
Fuel supply
Applies to: vehicles with gasoline engine
Using the right fuel helps keep the environment
clean and prevents engine damage .
Fuel recommendation
The fuel recommended for your vehicle is unlead
ed premium
grade gasoline . Audi recommends
using TOP TIER Detergent Gasoline with a mini
mum octane rating of91 AKI (95 RON). For more
information on TOP TIER Detergent Gasoline,
please go to the offic ial website
(www.toptiergas .com).
The recommended gasoline octane rat ing for
your engine can also be found on a label located
on the ins ide of the fuel filler flap. This rating
may be specified as AK I or RON .
Your veh icle may also be operated using unlead
ed regular gasoline with a minimum octane rat
ing of 87 AKl/91 RON . However, using 87 AKI/91
RON octane fuel w ill slightly reduce engine per
formance.
Use unleaded gasoline only. Unleaded gasoline
is available throughout the USA, Canada, and in
most European countries. We recommend that
you do not take your vehicle to areas or count ries
where un leaded gasoline may not be available.
For more information on refueling your vehicle,
see
~ page 269 .
Octane rating
Octane rating indicates a gasoline's ability to re
sist engine damaging "knock" caused by prema
ture ignit ion and detonation . T herefore, buy ing
the correct grade of gasoline is very important to
he lp prevent possible engine damage and a loss
of eng ine pe rformance.
Gasoline most commonly used in the United
States and Canada has the following octane rat
ings that can usually be found on the filler pump:
- Premium Grade: 91 - 96 AKI
268
-Regular Grade: 87 -90 AK I
Explanation of the abbreviations :
AKI =
Anti Knock Index = (R +M)/2 = (RON +MON)/
2
RON = Research Octane Number
MON= Motor Octane Number.
@ Note
- Do not us e any fuel with octane ratings low
er than 87 AKI or 91 RON otherwise expen
sive engine damage will occur .
- Do
not us e leaded gasoline. The use of lead
ed gasoline will severely damage your vehi
cle's catalytic converter and its ability to
contro l exhaust emissions .
Blended gasoline
Applies to: vehicles with gasoline engine
Use of gasoline containing alcohol or MTBE
(methyl tertiary butyl ether)
You may use unleaded gasoline blended with al
cohol or MTBE (commonly referred to as oxygen
ates) if the blended mixture meets the follow ing
criteria :
Blend of gasoline methanol (wood alcohol or
methyl alcohol)
-Anti -knock index must be 87 AKI or higher.
- Blend must contain no more than 3% metha-
nol.
- Blend must contain more than 2% co-solvents.
Blend of gasoline and ethanol (grain alcohol or
ethyl alcohol)
- Anti-knock index must be 87 AKI or h igher .
- Blend must not conta in more than 15% etha-
nol.
Blend of gasoline and MTBE
-Anti -knock index must be 87 AK I or h igher.
- Blend must not contain more th an 15% MTBE.
Seasonally adjusted gasoline
Many gasoline grades are blended to perform es
pecially well for winter or summer dr iv ing . Dur-
i ng seasonal change-over, we suggest that you
IJIJ,
Page 271 of 356

u. co .... N
" N .... 0 0 :c '
adjustment is more like ly to be made in time .
@ Note
-Methanol f uels whi ch do not meet these re
quirements may ca use corrosion and dam
age to plastic and rubber components in the
fuel system .
- Do not use fuels that fai l to meet the speci
fied criteria in this c hapter.
- If you are unable to determine whether or not a particular fue l blend meets the speci
fications, ask your service station or its fuel
supplier.
- Do not use fuel for which the contents can
not be identif ied.
- Fuel system damage and performance prob
l ems resulting from the use of fue ls differ
ent from those specif ied are not the respon
s ibility of Audi and are not covered under
the New Veh icle or the Emiss ion Control
System Warrant ies .
- If you experience a loss of fue l economy or
driveability and performance problems due
to the use of one of these fuel blends, we
r ecommend that you switch to unblended
fuel.
Gasoline additives
Applies to: vehicles with gasoline engine
A majo r concern among many auto manufactur
ers is carbon deposit build-up caused by the type
of gasoline you use.
A lthough gasoline grades d iffer from one manu
facturer to another, they have cer tain things in
common . A ll gasoline grades contain substances
that can cause deposits to collect on vita l engine
parts, such as fue l injectors and intake valves . A l
though most gasoline brands include additives to keep engine and fuel systems clean, they are not
equally effective.
Audi recommends using TOP TIER Detergent Gas
oline. For more informat ion on TOP TIER Deter
gent Gasoline, please go to the official website (www .toptiergas .com) .
Check ing and F illing
A fter an extended period of using inadequate
fuels, carbon deposit bui ld-ups can rob your en
gine of peak performance.
@ Note
Damage or ma lf u nction due to poor fue l qual
ity is not covered by the A udi New Vehicle
L imited Warranty .
Refueling
Fuel filler neck
The fue l filler neck is located on the rig ht rea r
s ide panel behind the fuel fille r flap .
If the power lock ing system should fa il, yo u can
st ill open the flap manually - fo r detailed instruc
tions see
~page 271.
You can find the fuel tank capacity of your vehicle
i n
~ page 334 .
The label on the inside of the fuel filler flap tells
you the correct fuel for your vehicle. For more in
format ion about fuel spec ificat ions, see
~ page 268 .
Your vehicle fuel tank has an onboard refuelling
vapor recovery system. T his feature helps to pre
vent fuel vapors from escaping from the tank and polluting the environment wh ile you refuel your
vehicle. In o rder to fill the tank proper ly w hile
prote ct ing t he env ironment, p lease follow t his
r ef uel ing p rocedure carefully.
& WARNING
= -
Unde r normal opera ting condi tions, neve r ca r
r y additional f uel containers in your car. Gas
canisters and other containers used to trans
port fue l can be dangerous. Such containers,
f u ll or empty, may leak and could cause a fire
i n a collision. If you must transport fuel to
use for your lawn mower, snow blower, etc.,
be ve ry ca refu l and always observe loca l a nd
state laws rega rding the use, transpo rta tion
a nd stor age of su ch f uel con tainers. Make cer
t ai n t he co nta iner meets indus try standards
(A NSI/AS TM F8S2 - 86) .
269
Page 272 of 356

Checking and Filling
(D Note
Never drive your vehicle until the fuel tank is
completely empty. The irregular supply of
fuel can cause m isfiring. Gasoline cou ld enter
the exhaust system and damage the catalyt ic
converter.
Fueling procedure
Fig. 252 Right re ar side of the vehicle: open ing the fue l
filler door
F ig. 253 Fue l filler doo r w it h attac hed fuel cap
The f uel fi ller door is unlocked or locked by the
central lock ing system.
Opening the fuel cap
• Presson the left s ide of the fuel filler door to
open
¢ fig . 252 .
• Unscrew the tank cap counterclockw ise.
• Place the cap from above on the open fue l filler
door
¢ fig. 253.
Clo sing th e fu el cap
• Screw the tank cap on to the r ight on the filler
neck until it cannot turn any farther .
• Close the fuel filler door and then press on the
left side until it latches.
270
Once the pump nozzle switches off, the fuel tank
is "full". Do not fill the tank more. Otherwise the
expans ion space in the tank w ill be filled.
The correct fuel type for your vehicle can be
fo und on a label located on the inside of the fuel
filler door . For additional information on fuel,
see ¢
pag e 268.
The fuel tank capacity of your veh icle is listed in
the
T echn ical Dat a section ¢ page 334.
To avo id fuel spilling or evaporat ing from the fuel
tank always close fue l cap prope rly and com
plete ly. An improper ly closed f uel fi ller cap may
also cause the M IL lamp ¢
page 25 to come on.
A WARNING
Not pay ing attention when fueling or han
dling fuel incorrectly can lead to fires, explo
sions or serious injur ies.
- Fue l ignites easily and can cause serious
burns and other injur ies.
-
- If you do not switch the engine off when fu
eling and/or do not insert the fuel nozzle
completely into the tank open ing, fuel can
leak out or run over. Leaked fuel can ignite
and start a fire .
- Do not use the telephone while fueling . The
electromagnetic rays can cause sparks,
which can ignite fuel vapors and start a fire .
- Do not sit in your vehicle wh ile fueling. If
you must make an exception and enter your
veh icle again while fueling, close the door
a nd touch metal to d ischa rge stat ic elect ric
ity before to uching the f uel no zz le. Static
e lec tricity ca n create spa rks, which ca n ig
n ite vapors when fueling.
- Do not smoke or have an open flame in the
a rea whe n fue lin g you r veh icle or filling a
fue l container because this increases the
risk of an explosion.
- F or your safety, carrying fuel containe rs in
your veh icle is not recommended . Whet her
fu ll or empty, the container can leak and
cause a fire in the event of an accident.
- If you must make an exception and trans
port a fuel container, note the fo llowing:
Page 274 of 356

Checking and Filling
Emissions control
systems
Catalytic converter
A pp lies to: ve hicles w ith gasoline engines
The vehicle may on ly be driven with unleaded
gasoline, otherwise the catalyt ic converter will be
destroyed.
Never d rive until the tank is comp letely empty .
The irregular supp ly of f uel that results from that
can cause engine m isfires. Uncombusted fuel will
enter the exhaust system , w hich can cause over
heating and damage to the catalyt ic converter .
A WARNING
The temperature o f the exha ust system is
hig h, bo th whe n driving and after stopping
t he engine.
-
- Never touch the exha ust ta il pi pes once they
h ave become ho t. This could resul t in burns.
- Do no t park you r vehicle ove r flammable
m aterials such as g rass or leaves because
t h e hi gh te mperat ure of the emiss io ns con
t rol sys te m c ould star t a fire.
- D o no t apply u nder bod y p rote ctant in the
exha ust syste m are a, bec au se t his in cre ases
t h e ris k of fire .
Engine compartment
Working in the engine compartment
Special core is required if you ore working in the
engine comportment
For work in the engine compartment such as
checking and filling fluids, there is a risk of in
jury , scalding , accidents, and burns . For this
reason, follow all the warnings and general
safety precautions provided in the following in
formation . The engine compartment is a dan
gerous area on the vehicle .
~ ,&..
A WARNING
- T urn the engine off.
- Switch the ign ition off .
- Set the parking b rake .
- Select the P selector leve r pos ition.
272
- Let the eng ine cool down .
- Never open the hood when there is steam o r
coo lant escapin g from the engine compart
ment, because there is a risk that yo u could
be burned. Wait unt il no steam or coolant is
escaping.
- Keep children away from the eng ine com
pa rtment.
- Never sp ill fluids on a hot engine. These flu
ids (such as the anti-freezing agent con
tained in the coolant) can ignite .
- Avoid short c ircuits in the electrical system.
- When working in the engine compa rtment,
remember that the radiator fan can switch
on even if the ignition is switched off, wh ich
increases the r isk of persona l injury.
- Never open the cap on the coolant expan
sion tank when the engine is warm. The
cooli ng system is under p ressure .
- To protect your face, hands, and a rms from
hot steam or coolant, cover the cap with a
large cloth when opening.
- Do not remove the engine cove r under any
circumstances . T his increases the risk of
burns.
- If tests need to be perfo rmed with the en
gine running, there is add itiona l danger due
to mov ing components (such as the r ibbed
be lt, alterna tor and rad iator fan) and from
the high-voltage ignition system.
- Do not unde r any circ ums tances activate the
throttle inadvertently (for example, by hand
from t he e ngine compartment) if the veh i
cle is stat ionary but the en gine is r un ning
an d a gea r is en gaged. Otherwise, the veh i
cle will start to move immediately and this
could result in an acc ident .
- Pay a ttent ion to the following wa rnings lis t
e d w hen wor k on the fue l system o r on the
electrical equipment is require d.
- Do no t smoke.
- Never work near open flames .
- Always have a working fire extinguisher
nearby.
- All work on the battery or elect rical system
in your vehicle can result in injuries, chemi
cal b urns, acc idents or bu rns. Because o f
this, all work m ust be perfo rmed
only b y an ~
Page 275 of 356

lL t:0 ....
"' ......
"' .... 0 0 :c '
authorized Audi dealer or autho rized Audi
Service Facility.
- To reduce the risk of electric shock and in
jury, never touch the following components
when the eng ine is running or is being start
ed :
- I gnition cable
- Othe r components in the electronic h igh-
voltage ignition system
- If you must check o r perform work on the
engi ne while it is run ning:
- Set the parking bra ke and p lace the se lec
tor lever in the P (pa rk) position first .
-Always p roceed with extreme ca utio n so
that clothing, jewelry or long ha ir do not
become caught in the radiator fan, fan
belt or other moving components or do
not come into contact with hot compo
nents . Tie back long ha ir before beginning
work and do not wear cloth ing that can
hang down into the engine .
- L imit your exposure to exhaust a nd chemi
cals to as short a time as poss ible ¢
A.
A WARNING
California Proposi tion 6S Warn ing:
- Engine exhaust, some of its constituents,
and certain vehicle components contai n or
em it chem icals known to the State of C ali
forn ia to ca use cancer and bi rth defects an d
re produc tive harm. In ad dition , ce rtain fl u
ids contained in vehicl es and certa in prod
ucts of com ponent wear contain o r emit
chemica ls known to the State of California
to cause cancer and birth defects or other
reproduct ive harm.
- Battery posts, termina ls and re lated acces
sories contain lead and lead compounds,
chemica ls known to the State of California
to cause ca ncer and reproduct ive harms .
Wash hands after handling .
(D Note
When fil ling fl uids, be sure not to mix the flu
ids up . Otherwise severe ma lfunctions and en
gine damage w ill occur.
Chec king and Filling
@) For the sake of the environment
You should regularly check t he gro und under
your vehicle in order to detect leaks quick ly .
If
the re are visible spots from o il or other fluids,
b ring your veh icle to an authorized A udi deal
er o r aut ho rized Aud i Serv ice Facility to be
checked .
Opening/closing the hood
The hood is released from inside the vehicle .
Fig. 256 Drive r footwell : re lea se leve r
Fig. 25 7 Rocker sw itc h unde r the hood
M ake s ure th e wipe r arms are no t rais e d up from
t h e windshie ld . Otherwise the pain t could be
damaged.
Opening the hood
.,. With the d rive r's doo r open, pull the lever be
low t he instrume nt pane l in the direction of the
ar row ¢
fig. 256.
.,. Ra ise the hoo d slightly¢&_ .
.. Press the rocker switch under the hood upward
¢ fig . 257. T his re leases the catch.
.,. Open the hood . ..,.
273