engine AUDI A8 2018 Manual PDF

u. co .... N
" N .... 0 0 :c ' Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
~ Note
Vehicles with an automatic transmission can­
not be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by con­
necting it to the battery of another vehicle .
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING -
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for safe
handling of your vehicle's battery .
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A dead battery can freeze at temperatures
around 32 °F (0 °C) . If the vehicle battery is
frozen, you must thaw it before connecting
the jump start cables. If you do not, this in-
Emergency situations
creases the risk of an explosion and chemi­
cal burns. After jump starting the vehicle,
drive to an authorized Audi dealer or author­ ized Audi Service Facility immediately to
have the vehicle battery checked.
- Do not allow battery acid to contact eyes or
skin . Flush any contacted area with water
immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion .
- Vehicle batteries generate explosive gases .
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12-Volt rating . The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah " rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped
in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen. The battery case may have be weak­
ened.
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c>page 272.
@ Note
- Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
( + ) terminals are connected.
327

Emergency situations
@ Tips
The discharged battery must be properly con­
nected to the vehicle's electrical system .
When jump starting or charging the battery,
never connect the negative ground cable to
the battery negative post because the battery
manager system must be able to detect the
battery's state of charge. Always connect the
negat ive g round cable to the negative ground
post of the battery manager control unit.
Using the jump start
cable
Both jump start cables must be connected in the
correct order!
Fig. 289 E ngin e compartme nt: co nn ectors for jump start
cables and a charger
Fig. 290 Jump starting using a battery in anot her vehicle:
A
-p rov id in g current, B -drai ned
The procedure for connecting jump start cables
that is descr ibed next is designed to help jump
start your vehicle.
Vehicle with discharged battery:
~ Turn off lights and accessories, move automatic
transmission lever to N (Neutral) or P (Park)
and set parking bra ke.
328
Connecting the positive cable (red) to the
positive terminal
~ Open the cover on the positive terminal
qfig . 289.
1. Secure one end of the pos itive cable (red) to
the jump start pin
(D q fig. 290 (pin under
the cover =
"plus") on the vehicle that needs
to be started @.
2. Secure the other end of the positive cable
(red) to the posit ive terminal @on the bat­
tery provid ing the cur rent @.
Connecting the negative cable (black) to the
negative terminal
3. Secure one end of the negative cable (black)
to the negative terminal @ on the battery
that is providing the current @.
4. Secure the other end of the negative cable
(black) to the jump start
pin @ (hex head pin
= "negative") on the vehicle that needs to be
started @.
Starting the engine
~ Sta rt the eng ine on the vehicle providing the
jump start @and let it run at idle.
~ Now start the engine on the vehicle with the
drained battery @.
~ If the engine does not start, stop the starting
procedure after 10 seconds and then repeat it
after approx imately 30 seconds.
~ Remove the cables when the engi nes are run­
ning. Remove them in reverse order from the
way they were installed.
~ Close the cover on the posi tive terminal.
The battery is vented to the outside to prevent
gases from enter ing the vehicle interior. Make
sure that the jumper clamps are well connected
with their
metal ports in full contact with the
battery terminals .
A WARNING
-To avoid serious personal injury and damage
to the vehicle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road service.
-Jumper cables must be long enough so that
the vehicles do not touch.
..,.

-When connecting jumper cables, make sure
that they cannot get ca ught in any mov ing
parts in the engine compartment.
- Before you check anything in the engine
compartment, a lways read and heed a ll
WARNINGS
¢ page 272.
(D Note
Impro per hook-u p of jum per cables can ru in
the generato r.
- Always connect P OSITIVE( +) to POSITIV E
( + ), and NEGATIVE( -) to NEGATIVE( -)
g round post of the battery manager contro l
unit.
- Check that a ll sc rew p lugs on the battery
cells are sc rewed in firmly . If not, t ighten
pl ugs p rior to connect ing clamp on negative
b atte ry te rmi nal.
- Please note t hat the procedure fo r con nect­
i ng a jumper cab le as desc ribed above ap­
p lie s specifica lly to the case of yo ur vehicle
b eing ju mp starte d. When you are g iv ing a
ju mp s tart to ano ther vehicle, do
not con­
n ect th e neg ative( -) ca b le to the neg ative
(-) t ermin al on t he disch arged batte ry @
¢ fig . 290. Instead, securely connect the
negat ive(- ) cab le to either a solid metal
component that is f irm ly bolted to the en­
gine block o r to the engine bloc k itself. If
the battery that is be ing c ha rged does not
vent to the outs ide, escap ing batte ry gas
could ignite and ex plod e!
Towing with a tow truck
General hints
Yo ur Audi requires special h andling for towing .
The follow ing informa tion is to be used by com­
mercia l tow tr uck o pera tors who know how to op ­
e rat e the ir equip men t sa fely.
- Never tow your Audi. Towing will cause dam­
age to the engine and transmission.
- Never wrap the safety chains or winch cables
~ around the brake lines. ....
~ -To prevent unnecessary damage, your Audi N
8 must be transported with a flatbed truck. 0 :c ' Emergency situations
-To load the vehicle on to the flatbed, use the
towing loop found in the vehicle tools and at­
tach to the front or rear anchorage
¢ page 329 and c> page 330.
A WARNING
A veh icle being towed is not safe for passen­
ge rs. Neve r allow a nyo ne to ride in a vehicl e
b eing towed, fo r any reason.
Front towing loop
Fi g. 291 Fron t bu mpe r: removing t he cap
Fig. 292 Fron t bu mpe r: insta llin g the tow ing loop
The thread for the towing loop is on the right
s ide of the front bumper beh ind a cap.
.,. Remove the towing loo p from the vehicle too l
kit.
.,. Press the cap inward with brief, forceful pres­
sure
c> fig. 291 . The cap will loosen from the
bumper.
.,. T igh ten the tow ing loop in the threaded open ­
ing until it stops
c> fig. 292 and t hen tighten it
w ith a wheel w re nc h .
.,. Afte r usi ng, p lace the tow ing loop b ack in the
veh icle tool kit.
IJJ>-
329

lL t:0 ....
"' ......
"' .... 0 0 :c ' Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lift ed at the lifting
points illus tr at ed.
Fig. 296 Fro nt lift in g poin t
Fig. 29 7 Rear lift ing poin t
.,. Read and heed WARNING c::> &, .
.. Activate the veh icle ja ck mode in the MMI :
I CARI funct ion button> Car systems control
button >
Servicing & checks > Air susp.: jack
mode > On .
.. Loca te lift ing po ints c::> fig . 296 and c::>fig . 297 .
.. Adju st lifting arms of wo rkshop ho ist o r floo r
ja ck t o ma tch vehicle li fting poin ts.
.. In se rt a rubb er pa d between the floor j ack/
wor kshop ho ist and the lifting points .
T he vehicle ja ck mode m ust be a ct iv a te d so th at
the au tomatic a djustment of the Ad aptive Air
Suspension does not m ake it more diffic ult to
raise the ve hicle wit h the floor jack.
If you must lift your vehicle with a floor jack to
work underneath , be sure the vehicle is safely
supported on stands intended for this purpose .
Emergency situations
Front lifting point
The lifting poi nt is locate d on the floor p an rein ­
f o rcement about at the same level as the ja ck
mounting point
c::> fig . 296 . Do not lift the vehi­
cle at the vertical sill reinforcement .
Rear lifting point
T he lifting p oin t i s lo cate d on the ve rtic al rei n­
f o rceme nt o f th e lower s ill for the on- bo ar d jac k
c::>fig. 297 .
Lifting with vehicle jack
Refer to c::> pag e 315 .
A WARNING
- To reduce the r is k of se rious inju ry and veh i­
cle dama ge.
- Always lift the vehicle o nly at the specia l
wor kshop h oist a nd f loor jack lift points
il­
l ustrated c::> fig. 296 and c::> fig. 297.
- Failure to lift t he ve hicle at these points
could cause the veh icle to tilt o r fall from
a lift i f there is a change in vehicle weight
dist ribution and balance . This might hap­
pen, fo r example, when h eavy compo­
nents such as the eng ine block o r trans­
missi on are re moved .
- Whe n re mov ing heavy comp onents like
these, an ch or veh icle t o hois t or ad d co rre­
spon ding weig hts t o m aintai n the cen ter of
g ravi ty . Ot herw ise, the vehicle mig ht tilt or
slip off t he hoist, caus ing se rio us pe rsonal
i njur y .
(D Note
- Be aw are of the fo llow ing po ints b efor e lift­
ing the vehicle:
-The vehicle should never be lifted or
jacked up from underneath the engine oil
pan, the transmission housing, the front
or rear axle or the body side members.
This could lead to serious damage .
- To avoid damage to the underbody or
chassis frame, a rubber pad must be in­
serted between the floor jack and the lift
points .
.,.
331

lL t:0 ....
"' ......
"' .... 0 0 :c ' Technical data
Vehicle specifications
XXXXX XX · X · XXXX XXX xx
®-+ IAHRZG.-IOEN T · NR. Vllllll • WIT • NO. XXXXXXXX XX X XXXXX XXX
TYP /Tffl XXX XXX
xx xxxxxxx xx xx
xx
XXX KW XXX
~ t!lll /TRANS. lllllE xxxx XXX XXX ®-t 11)10111<8./GllllkS .
©+ IAO(NR.I IN NENAllSSl.
XXXX I XXXX XXX I XX PAI NT liO./ ffT[JIQI
II. · AIJSlit / OPTIONS
EOA 7D 5 4U B 6XM SSG SR W
2 EH JO Z 1LB 1AS 1 BA
3FC S MU 7Xl
F O A 9G3 OG7 O YH OJF
TL 6 3 KA 8EH UlA X 9B OZ7
l XW
803
908 8Z4 020
7 T6 CV7
71<0 4X3 21< 2
3L4 4 KC 3YO 413 5 02
1S A 7GB
01A 4GQ
XX . X XX X XX X xxxx
Fig. 298 Vehicle ident ifica tion labe l
Vehicle Identification Number (VIN )
The VIN n umber is located in the following pla­
ces :
0
0
~ :x: - In the Infota inment system: se lect: the !CARI
func tion b utton > Car sy stem s contro l bu tton >
Serv ice
& control > VIN number .
-on the vehicle identification label
- under the w indshield on the dr iver's side
Vehicle identification label
The vehicle identification l abe l¢ fig. 298 is locat­
ed in the luggage compartment under the cargo
floor cover in the spare wheel well.
The information of the vehicle identification labe l
can also be found in your Warranty
& Mainte­
nance booklet.
Technical data
T he sticke r contains the fo llow ing vehicle data:
(D Vehicle Identificat ion Numbe r (VIN)
@ Vehicle type, eng ine output, transm iss ion
@ Engine and transmission codes
@ Paint and interior codes
® Optional equipment numbers
Safety compliance sticker
T he safety compliance sticker is yo ur ass ura nce
that your new veh icle complies w ith all applicable
Federal Motor Vehicle Safety Standards which
were in effect at the time the vehicle was man u­
factu red. Yo u can find this st icker on the door
jamb on the driver's side. It shows the month and
year of production and the ve hicle identificat ion
numbe r of your ve hicle (perforation) as well as
t h e Gross Vehicle Weight Rat ing (GVWR) a nd the
G ross Axle We igh t Rating (GAWR).
High voltage warning label
The high voltage warning label is located in the
engine compartme nt next to the engine hood re ­
lease. The spark ignition system comp lies with
the Canadian standard ICES-002 .
Notes about technical
data
T he values may vary b ased on s pecial eq uipmen t
as well as market -specific equipment and meas ­
u ring methods .
Please note that the specifications listed in the
vehicle documen ta ti on a lways take prece den ce.
(D Tips
Missing tec hnical data was no t ava ilable at
the time of pr int ing.
333

Technical data
Gasoline engines
AB 3.0, 6 cylinder
Maximum output SAE net hp@rpnn 333 @ 5500 - 6500
Maximum torque SAE net lb-ft @ rpm 326@ 2900
-5300
Displacement CID (cm
3
) 182 .7 (2995)
Engine oil with filter change
1>
Fuel Premium unleaded (91 AKI),¢ page 268, Gasoline
AB 4.0, 8 cylinder
Maximum output SAE net hp@ rpnn 450@ 5300 - 6000
Maximum torque SAE net lb
-ft @ rpm 444@ 1500 -5250
Displacement CID (cm
3
) 243 .6 (3993)
Engine oil with filter change
1
)
Fuel Premium unleaded (91 AKI), r:=;, page 268, Gasoline
58 4.0, 8 cylinder
Max imum output SAE net hp@ rpnn 520@ 5800 - 6400
Maximum torque SAE net lb
-ft@ rpm 481@ 1700 -5500
Displacement CID (cm3
)
243 .6 (3993)
Engine oil with fi lter change1
)
Fuel Premium unleaded (91 AKI), r:=;,page268, Gasoline
58 plus 4.0, 8 cylinder
Maximum output SAE net hp@rpnn 605@ 6100 - 6800
Maximum torque SAE net lb
-ft@ rpm 517@ 1750- 6000
Max imum torque SA E net with over lb-ft@ rpm 553 @ 2500 - 5500
boost
Displacement CID (cm
3
) 243.6 (3993)
Engine oil with filter change
1>
Fuel Premium unleaded (91 AKI),¢ page 268, Gasoline
ll For specific engine oil capacities, please see
the most current information for the USA at http :/ /www.audiusa.com/help/maintenance or
for Canada at http://www.audi.ca/ca/brand/ en/
your _aud i/ au d i_ services _a nd/
Care _and _Maintenance/schedule .htm l or ca ll
~ 800-822-2834 . .... N
" N .... 0 0 :c ' 335

Consumer Information
Consumer Information
Warranty coverages
Your Audi is covered by the following warran­
tie s:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Con trol Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulati ons in the United States and
Canada require that automobi les meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana ­
da differ from vehicles sold in other countries.
If you plan to take your vehicle outside the conti­
nenta l limits of the United States or Canada,
there is the possibility that:
- un leaded fue ls for vehicles with catalytic con­
verter may not be available;
- fuel may have a conside rably lower octane rat­
ing . Improper fuel may cause engine damage;
- se rvice may be inadequate due to lack of proper
service facilities, tools or testing equipment;
- r eplacement parts may not be readily available.
- Nav igat ion systems for veh icles built for the
U .S .A . and Canada w ill not necessarily work in
Europe, and may not wo rk in other count ries
outside North America.
336
@ Note
Audi cannot be responsib le for mechanical
damage that could resu lt from inadequate
fuel, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and Litera ­
ture are published as soon as poss ible after mod­
el introduction. Se rvice manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at:
www.audi.techliterature.com
Maintenance
General
Your vehicle has been designed to help keep
maintenance requirements to a minimum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your vehicle's safety,
economy and reliability . For detailed vehicle
maintenance consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam­
ple at extremely low outside temperatures, in
very dusty regions, when towing a trailer very fre­
quently, etc. , some service wo rk shou ld be per­
fo rm ed between the intervals specified. This ap­
plies particularly to:
- oil changes , and
- cleaning or replac ing the a ir filter .
@ For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that em iss ion standards are
maintained, thus minimizing adverse effects
on the enviro nment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the generally increasing technica l complexity of
.,,.

u. co .... N
" N .... 0 0 :c ' today's automobiles, have steadily reduced the
scope of maintenance and repairs which can be
carried out by veh icle owners.
Al so , sa fet y a nd
en vironmental
concerns place very strict limits
on the nature of repairs and adjustments to en­
g ine and transm ission parts wh ich a n owner can
perform .
Maintenance, adjustments and repairs usually re­
qu ire special tools, test ing devices and other
equ ipment available to specially trained work ­
shop personnel in order to assure proper per­
formance, re liability a nd safety of the veh icle and
its many systems .
Improper maintenance, adjustments and repairs
can impair the operation and reliab il ity of your
ve hicle and even void your veh icle warranty .
Therefo re, proof of se rvicing in accordance w ith
the ma intenance schedule may be a condition fo r
upho ld ing a possib le warranty claim made within
the warranty period.
Above all , ope rational safety can be adversely af­
fected, creating unnecessa ry risks fo r yo u and
your passengers.
I f in do ubt about any servicing, have it done by
your author ized Audi dealer or any other prope rly
eq uipped and qua lified workshop. We strongly
u rge yo u to g ive your author ized Audi dealer the
opportunity to perform a ll scheduled mainte ­
nance and necessary repairs. Your dealer has the
facilities, original parts and trained specialists to keep your veh icle running properly .
Pe rforming limit ed maint enanc e yourself
The fo llowing pages describe a limited number of
procedures which can be performed on your ve hi­
cle with ordinary tools, should the need arise and
trained personnel be unavailable. Before per­
forming any of these procedures, always thor­
oug hly read a ll of the app licable text and careful­
ly follow the instructions g iven . Always rigorously
observe the
W ARNINGS prov ided .
Before you check an ything in the eng ine com ­
partment , alw ays read and he ed all WARNINGS
c:> &. and c:> &. in Working in the engine compart­
ment on page 2
72 .
Con sum er In form ation
A WARNING
--
- Ser ious personal injury may occur as a result
of improperly performed maintenance, ad ­
justments or repairs .
- Always be extremely careful when work ing
on the vehicle . Always follow commonly ac­
cepted safety practices and general com­ mon sense. Never risk pe rsonal inj ury.
- Do not attempt any of the maintenance,
checks or repairs described on the following pages if you are not fu lly famil iar with these
or other proced ures with respec t to the ve­
h icle, or are uncerta in how to pro ceed.
- Do not do any work without the proper tools
and eq uipment. Have the necess ary wo rk
done by your authorized Audi dealer or an­
other proper ly equipped and qualified work­
shop.
- The engine compartment of any motor vehi ­
cle is a potentially hazardous area . Never
reach into the area around or touch the radi­
ator fan.
It is temperature controlled and
can switch on suddenly - even when the en­
g ine is off . The radiator fan switches on au­
tomatically when the coolant reaches a cer­
tain tempe rature and will cont inue to run
until the coolant temperature d rops.
- Always sw itch off the ignition before anyone
gets under the vehicle.
- Always support your veh icle with safety
stands if it is necessary to work underneath
the vehicle. The jack suppl ied with the veh i­
cle is no t adequate for this pu rpose and
could collapse caus ing serious personal in­
jury.
- If you must wor k unde rne ath the vehicle
with the wheels on the ground, always make
sure the vehicle is on level ground, that the
wheels a re always sec urely blocked and that
the engine cannot be started.
- Always make sure the transmission se lector
lever (automatic transmiss ion) is in
"P"
(Park position) and the pa rk brake is ap­
plied.
337

Consum er Info rmation
@ For the sake of the environment
- Changing the engine settings wi ll adverse ly
affect emission leve ls. Th is is detrimental to
the env ironment and increases fuel con ­
sumption.
- A lways observe environmenta l regu lations
when disposing of o ld engine o il, used brake
flu id, d irty engine coolant, spent batteries
or worn out tires.
- Undeployed airbag modules and pretension­
ers might be classif ied as Perchlorate Mate­
rial -spec ia l handl ing may apply, see
www.dtsc.ca.gov/hazardouswaste/ perch lorate. Whe n the vehicle o r parts of
the rest raint system including airbag mo d­
ul es safety bel ts w it h pre tensioners are
scrapped, all applicable laws and regula ­
tions must be observed. Yo ur autho rized
A udi dealer is familiar with these require ­
ments and we recommend that you have
your dealer perform this service for you.
Accessories and technical changes
Additional accessories and parts
replacement
Always consult on authorized Audi dealer before
purchasing accessories.
Audi ve hicles that are constructed with advanced
materials like Steel/Alum inum (Hybrid construc­
tion), Aluminum (Aud i Space Frame), and/or A lu­
minum/Carbon F iber (Ultra Advanced L ight
We ight Materials) are as un ique as the ir drivers .
Therefo re, the ava ilability of ce rtain parts needed
for repai r, restorat ion, or reco nstr uction w ill be
rest ric ted, or p arts w ill be unav ailable, if the ve ­
h icl e is not repa ired a t an a uth o rized Aud i colli­
sion repair facili ty . This in cl udes but is not limit ­
ed to structura l parts w hic h require specia lized
training and equipment to restore their crash ­
worthiness back to the orig inal NHTSA and IIHS
performance.
Your vehicle incorporates the latest safety design
features ensuring a hig h standard of active and
passive safety.
338
This sa fety could be com promised by non -ap ­
proved changes to the vehicle . For t his reason, if
parts have to be rep laced, p lease observe the fol ­
l owing points when install ing additional accesso ­
ries:
Approved Audi accesso ries and gen uine A udi
parts are avai lab le from a uthorized Aud i dea le rs .
These dea le rs al so have t he necessa ry fa cilit ies,
tools and trained specialists to install the parts
and accessories properly .
A WARNING
Using the wrong spare parts or using non -ap ­
p roved accessories can cause damage to the
vehicle and serious personal i njury.
- Use on ly accessories express ly approved by
Aud i and genuine Audi spare parts
- These parts and accessor ies have been spe­
cially des igned to be used on your vehicle.
- Do not use license p late brac kets in the
front area that are d if f erent from the one
installed at the factory, or add additional li­
cense plate brackets.
- Never install accessor ies such as telephone
cradles or beverage holders on airbag covers
or w ith in the airbag dep loyment zones. Do­
ing so will increase the risk of injury if a ir­
bags are triggered in an accident!
- Before you check anyth ing in the eng ine
compa rtme nt, always read a nd heed all
WARN INGS
~page 272.
@ Note
-If items other than genu ine A udi spare
parts, add-on equipment and accessory
i t ems are used o r if repa ir wor k is not per­
formed according to specified methods, th is
c an resul t in seve re damage to you r vehi­
cl e's eng ine a nd body ( such as cor rosion)
and adve rsely aff ec t your ve hicle's war ran ty.
- Th e innovat ive alum inum con cep t of yo ur
Audi AB means t hat all se rvi cing, re pairs o r
ot her wor k on t he ve hicle body mus t be ca r­
ried out exclus ively by an Aud i workshop .
- I f emer gency rep air s mus t be pe rformed
elsew here, have the vehicle exam ined by an
authorized A udi dealer as soon as possib le .
.,,.

Index
Brakes Brake assist
Brake fluid
129
127
279
Electromechanical parking brake . . . . . . . . 81
Emergency braking function . . . . . . . . . . . . 81
New brake pads . . . . . . . . . . . . . . . . . . . . . 129
Worn brake pads . . . . . . . . . . . . . . . . . . . . . 23
Braking g uard . . . . . . . . . . . . . . . . . . . . . 95, 100
Messages 102
Brea k-in period
Tires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
73
Break ing in
New b rake pads
129
New engine . . . . . . . . . . . . . . . . . . . . . . . . . 73
New tires 290
Browsing through album covers . . . . . . . . . 191
Bulbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 326
Bu ttons
Mul tifunction steeri ng wheel . . . . . . . . . . .
11
C
Cable (Aud i mus ic interface)
California Proposition
65 Warning .... .. .
Battery specific . ............. .... .. .
Ca ll
.. .. .. ...... ... .. ..... ... .. .. ...
Call l ist
186
273
280
150
149
Ca ll opt ions . . . . . . . . . . . . . . . . . . . . . . . . . . 156
Ca pac it ies
F ue l tank
....... ... .. ..... ... .. .. ... 334
Washer fluid rese rvoir . . . . . . . . . . . . . . . . 334
Ca r ca rr ie r
T ra nsport ing you r vehicle . . . . . . . . . . . . .
330
Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
Ca rgo area
refer to L uggage compartment. ... .. ... 2 13
Cata lytic conve rte r
CD 27 2
refer to Med ia . . . . . . . . . . . . . . . . . . 181, 190
Ce ll phone
P laying music . . . . . . . . . . . . . . . . . . . . . . .
184
also refer to Telephone . . . . . . . . . . . . . . . 147
Ce nte r console ligh ting . . . . . . . . . . . . . . . . . 4 7
Central locking . . . . . . . . . . . . . . . . . . . . . . . . 27
Central lock ing switch . . . . . . . . . . . . . . . . . 3 1
Conven ience key . . . . . . . . . . . . . . . . . . . . . . 30
E me rgency lock ing . . . . . . . . . . . . . . . . . . . . 3 2
342
Luggage compartment lid . . . . . . . . . . . . . . 33
Remote control key . . . . . . . . . . . . . . . . . . . 30
Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Certification .. .. .. .. .. ............. ..
Ch . · ·1 anging engine 01 •• •• •.. .. ..... ... ..
Changing the battery ... ... .. ..... ... . .
Charg ing and chang ing the battery ...... .
Child restra ints .. .. .. .. ............. . .
Danger of using child restra ints in the front
339
277
199
199
267
seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Child restraint system anchors . . . . . . . . . . 262
Child safety . . . . . . . . . . . . . . . . . . . . . . . . . . 249
G ui dance fixtures for lowe r ancho rages . . 2 63
Child safety lock . . . . . . . . . . . . . . . . . . . . . . . 36
Child safety seat . . . . . . . . . . . . . . . . . . . . . . 254
Child safety seats . . . . . . . . . . . . . . . . . . . . . 255
Convertib le child seats . . . . . . . . . . . . . . . 256
Infa nt seats . . . . . . . . . . . . . . . . . . . . . . . . 2 55
Installing a c hild restraint using t he LATCH
system . . . . . . . . . . . . . . . . . . . . . . . . . . . .
264
LATCH system . . . . . . . . . . . . . . . . . . . . . . 264
Lower anchorages . . . . . . . . . . . . . . . . . . . 263
Mounting and re leas ing the anchorage
hook ..... .... .. .. .. ............. ..
264
Safety instructions . . . . . . . . . . . . . . . . . . . 252
Securing
Cleaning 259
306
Cleaning/removing ice from w indows . . . . . 308
Cleaning Alcantara . . . . . . . . . . . . . . . . . . . . 309
Cleaning artificia l leather. . . . . . . . . . . . . . . 309
Cleaning carbo n pa rts . . . . . . . . . . . . . 308, 309
Cleaning cont rols . . . . . . . . . . . . . . . . . . . . . 308
Cleaning decorative p arts and trim . . . . . . . 308
Cleaning disp lays . . . . . . . . . . . . . . . . . . . . . 308
Cleaning exhaust tail pipes . . . . . . . . . . . . . 308
Cleaning plastic pa rts . .. ............. . .
Cleaning tail lights . .. .. ............. . . 308
307
Cleaning textiles . . . . . . . . . . . . . . . . . . . . . . 309
Clock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Closing
Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
273
Panorama glass roof . . . . . . . . . . . . . . . . . . 39
Su nroof . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Su nshade (panorama glass roof) . . . . . . . . 40
Sunshade (slid ing/t ilting sunroof) . . . . . . . 38
Windows . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7