engine AUDI Q2 2021 Owner´s Manual

Instruments
and
controls
The brakes
may
perform differently than usual
and
the
brake pedal may vibrate.
Drive
to
a qualified workshop without delay
and

have
the
fault rectified.
A WARNING
- Before opening
the
bonnet and checking
the

brake fluid level, observe
the
warning infor­
mation
on
*$page
295,
Working
on
compo­
nents
in the
engine compartment.
-
If
the brake warning lamp does
not go out,

or
if it
lights up when driving,
the
brake
flu­

id level in
the
reservoir
is too low -
this
may

cause an increased accident risk. Stop
the

vehicle and
do not
drive on. Obtain profes­
sional assistance.
-
If
the brake warning lamp lights
up
togeth­
er with
the
ABS indicator lamp and
the
ESC
indicator lamp, this can mean that
the
con­

trol function
of
the ESC/ABS
is not
working.
Input from
the
functions that stabilise
the

vehicle
is no
longer available. This could
cause
the
tail of
the vehicle
to
skid
side­

ways.
Do not
drive on. Obtain professional
assistance.

(®)/0
Electro-mechanical parking brake
The warning lamp
||
lights
up
when
the
parking
brake
is
applied.
If the warning lamp
||
flashes, insufficient brak­
ing force
has
been applied
or
released. Select
first gear (manual gearbox)
or
position
P
(auto­
matic gearbox)
as an
additional safeguard. Make
sure that
the
warning lamp has gone
out
before
you drive
off.

2J
Parking brake!
There
is
a malfunction
in the
parking brake. Drive
to a qualified workshop soon
and
have
the
fault

rectified.

[ft]
Parking brake auto release: unavailable
If this message appears, press
the
brake pedal
and then release
the
parking brake.
If the warning lamp flashes and
the
message
ap­

pears,
the
brake
may not be
strong enough
to

hold
the
vehicle. The brakes have overheated.
The vehicle can roll away, even
on a
gentle slope.
©J Parking brake is applied
If this message appears, press
the
brake pedal
and then reLease
the
parking brake
as
necessary.
For further information
on the
parking brake
refer
to
^>page
82.

•as
Cooling system

| Switch
off
engine and check coolant level.
See owner's manual
The coolant level
is too low.

Switch
off
the engine and
do not
drive on. Check
the coolant level
^>page
299.

-
If
the coolant level
is too
low, add more coolant

^>page
300. Do not
drive
on
until
the
warning
lamp has gone
out.

| Coolant temperature too high! Let engine
run with vehicle stationary
Let
the
engine cool down
by
running
it at
idling
speed
for
a
few
minutes until
the
warning lamp
goes
out.

-
Do not
drive
on if
the warning lamp does
not

disappear. Obtain professional assistance.

JgJ
Caution:
Vehicle parked
too
steep
A WARNING
- Never open
the
bonnet
if
you
can see
or
hear
steam
or
coolant escaping from
the
engine
compartment; there
is
a risk
of
being
scal­

ded.
Wait until you
can no
longer see
or

hear escaping steam
or
coolant.
-The engine compartment
of
any motor
vehi­

cle
is
a dangerous place. Before carrying
out

any work
in the
engine compartment, switch
off the engine and allow
it to
cool down.
Please observe
the
important safety warn­
ings
^>page
295,
Working
on
components
in
the
engine compartment.
30

Instruments and controls
© CAUTION

CO
<
O
rN
iv
rN
•-i

00
Do not drive on if the warning lamp || lights

up;
otherwise there is a risk of engine dam­

age.

t^
Engine oil pressure
| Switch off engine! Oil pressure too low
Switch off the engine and do not drive on. Check
the engine oil level
^>page
298.
- If the engine oil level is too low, add more oil

tapage
297. Do not drive on until the warning
lamp has gone out.
-If the engine oil level is OK
but
the warning
lamp still lights up, switch off the engine and
do not drive on. Obtain professional assistance.
© Note
The oil pressure warning lamp is not an
indi­

cator for the oil level. The oil level should
therefore be checked regularly.

C3
Alternator/vehicle battery
| Electrical system: fault. Battery is not being
charged
There is an alternator fault or a fault in the
vehi­

cle's electrical system.
Drive to a qualified workshop without delay.
However, you should avoid using electrical equip­
ment that is not absolutely necessary because
this will drain the battery. If the battery charge is
insufficient, obtain professional assistance.

S
Electrical system: fault. Please contact
workshop
Drive to a qualified workshop without delay.
Avoid using electrical equipment that is not abso­
lutely necessary (such as the radio) because this
will drain the battery. If the battery charge is in­
sufficient, obtain professional assistance.

y
Electrical system: low battery charge. Bat­
tery will be charged while driving
Starting reliability may be impaired.
If this message disappears after a while, the ve­
hicle battery will have been sufficiently charged
while driving.
If the message does not disappear again, drive to
a qualified workshop without delay and have the
fault rectified.

2f
Safety systems
The indicator lamp

terns.

monitors the safety sys-

If
the indicator lamp
Ej
lights up or flashes,
there is a malfunction in one of the safety sys­

tems.

Drive to a qualified workshop without delay and
have the fault rectified.

A
WARNING
Have the safety systems examined without
delay; otherwise they may fail to trigger in an
accident - this could result in serious or possi­
bly fatal injury.

A
Front seat belt
The warning lamp|| lights up and does not go
out until the driver's and front passenger's* seat
belts have been fastened. When the vehicle has
gathered speed you will also hear a warning

chime.

Note
For further information on the seat belts

•=>
page 275.

y/4
Rear seat belt
Applies to: vehicles with seat belt warning system (rear seats)
If a rear seat belt is buckled/unbuckled, the cor­
responding indicator Lamp Lights up briefly.

||
- If the indicator lamp lights up briefly, the
corresponding rear seat is not occupied.

|/RI|-
If the indicator lamp lights up briefly,
the rear seat belt has been fastened.
| /
KJ
"
Ifthe
warning lamp flashes, the seat
belt has been unbuckled with the vehicle moving.
31

Instruments and controls
When the vehicle has gathered speed you will al­
so hear
a
warning chime.

Clutch
Applies to: vehicles with manual gearbox
© Note
For further information on the seat belts

•=>
page 275.

©-•
Steering lock
| Do not drive vehicle: steering defective
There is a malfunction in the electronic steering
lock. The ignition can no longer be switched on.
Do not have the vehicle towed away, because you
won't be able to steer it. Obtain professional as­
sistance.

^3
Steering lock: system fault! Please contact
workshop
There is a malfunction in the electronic steering
lock.
Drive to a qualified workshop soon and have the
fault rectified.

A WARNING

Your vehicle must not be towed if there is a
fault in the electronic steering Lock - risk of
accident!

-=*>
Engine start system

H
Engine start
system:
system fault! Please
contact workshop
Do not switch off the ignition; otherwise you may
not be able to switch it on again.
Drive to a qualified workshop without delay and
have the fault rectified.

3
Engine start
system:
system fault! Please
contact workshop
There is a malfunction in the engine start system.
Drive to a qualified workshop soon and have the
fault rectified.

jBy
Clutch:
fault. Please contact workshop
There is a permanent malfunction in the clutch.
The transmissible torque is reduced. You can
con­

tinue driving, but avoid placing an excessive load
on the clutch. Do not slip the clutch for too
long,

for example when driving away on a slope, tow­
ing a trailer or when parking. Drive to a qualified
workshop soon and have the fault rectified.

Q}
Clutch: overheating. Please adapt driving
style
There is a malfunction in the clutch. The trans­
missible torque is reduced. You can continue

driving,
but avoid placing an excessive load on
the clutch. Do not slip the clutch for too
long,
for
example when driving away on a slope, towing a
trailer or when parking. The indicator lamp will
go out when the transmission capability of the
clutch has been restored completely.

^
Engine stopped while vehicle is moving
| Engine stopped: brake servo and power
steering not possible
There is a malfunction in the engine or fuel sup­
ply system.
Greater strength is required to steer and brake
the vehicle if the engine stops while the vehicle is

coasting.
Carefully try to bring the coasting
vehi­

cle safely to a standstill out of the way of moving
traffic. Obtain professional assistance.
A WARNING
Greater strength is required to brake the
vehi­

cle if the engine stops while the vehicle is
moving - risk of accident! Greater strength
will be required to steer the vehicle unless the
power steering is still providing assistance.
The power steering may still be available if
the vehicle is still coasting with the ignition
switched on (and the vehicle battery charge is
sufficient).
32

Instruments and controls

CO

< o rN
iv
rN
•-i

00

£=s
Bonnet
| Warning! Bonnet not locked. Stop vehicle
and check bonnet lock
If the warning lamp lights up and the message
appears, the bonnet lock is not correctly engag­

ed.

Stop your vehicle without delay and close the
bonnet
^page
296.

f*lu
Electronic stabilisation control (ESC)
If the indicator lamp
§jj
flashes while the vehicle
is in motion, the ESC or traction control system
(ASR) is intervening.
If the indicator lamp
§|j
lights up, the ESC sys­
tem has been switched off for system reasons. In
this case, the ESC can be reactivated by switching
the ignition off and then on again. If the indica­
tor lamp goes out, this means the system is fully

functional.

If the indicator lamp
|g
lights up, the ESC sys­
tem has been partially or completely switched off
via the
J^OFF
button
^>page
145.
Stabilisation control (ESC/ABS): fault! See
own­

er's manual
If the indicator lamp
§§J
and the ABS indicator
lamp
EJ
light up and the message appears,
there is a malfunction in the anti-lock brake sys­
tem or electronic differential lock. This will also
cause an ESC malfunction. The vehicle can still be
braked in the normal way (however the ABS
con­

trol function will be out of action).
Drive to a qualified workshop without delay and
have the fault rectified.

(T)
Note
For more information about the ESC and ABS
systems, refer to
^>page
145.

O Brake
pads

S
Brake pads!
The brake pads are worn.
Drive to a qualified workshop without delay and
have the brake pads checked.

*S
Hill hold assist

|§i
Hill hold assist: unavailable
If this message appears, the hill hold assist is un­
available.
Manual control!
If this message appears, press the brake pedal.
Use the parking brake for the hill start

^>page
82.

<^b
Engine management
Drive system: fault. Please contact work­
shop
If the indicator lamp
Qg
lights up, there is a fault
in the engine management system.
Drive slowly to a qualified workshop without de­
lay and have the engine checked.
EPC Engine management
Applies to: vehicles with petrol engine
If the indicator lamp
\$fi
lights up, there is a
fault in the engine management system.
Drive slowly to a qualified workshop without de­
lay and have the engine checked.

W
Engine management
Applies to: vehicles with diesel engine
If the
indicator
Lamp
|jjj
Lights up when the
igni­

tion is switched on, the glow plugs are preheat­

ing.

If the indicator lamp does not light up or if it
flashes while the vehicle is moving, there is a
fault in the engine management system.
Drive slowly to a qualified workshop without de­
lay and have the fault rectified.

O
Emission control system
If the indicator Lamp
£3 Lights
up or flashes, a
fault has occurred which can reduce the quality of •
33

Instruments and controls
the exhaust gas and damage the catalytic
con­

verter.
Drive slowly to a qualified workshop without de­
lay and have the fault rectified.
Diesel particulate filter
Applies to: vehicles with diesel particulate filter

|
Particulate filter: system fault. See owner's
manual
The diesel particulate filter requires regenera­

tion.
You can assist the self-cleaning function of
the filter by driving as follows:
Drive at a speed of at least 60 km/h for about
15 minutes in 4th or 5th gear (on vehicles with
manual gearbox), or with the selector lever in po­
sition S (on vehicles with automatic gearbox).
Keep the engine speed at about 2000
rpm.
As a
result of the increase in temperature, the soot in
the filter will be burned off. The indicator lamp
will go out once the cleaning process has been
completed successfully.
If the indicator lamp does not go out, drive to a
qualified workshop without delay and have the
fault rectified.
A WARNING
It is essential that you adjust your speed to
suit the weather,
road,
terrain and traffic
con­

ditions. The recommended driving speed
must never lead to the driver disregarding the
traffic regulations.

(T) Note

For more information about the diesel partic­
ulate filter, refer to
^>page
295.
!
»
Engine speed governing
Applies to: vehicles with engine speed governing
[51 Max. engine speed: XXXX rpm
The engine speed will automatically be governed
to the speed displayed in the instrument cluster.
This protects the engine from overheating.
The rev limiter is deactivated as soon as the en­
gine temperature is no longer within the critical
range and you have taken
your
foot off the accel­
erator.
If the rev limiter has been activated because of a
fault in the engine management system, the in­
dicator lamp
Q or[|2g
will also light up. Make
sure that the engine speed does not exceed the
speed displayed in the driver information system,
for example when shifting down a gear. Drive to
a qualified workshop without delay and have the
fault rectified.
Engine oil level
(MIN)
23
Please check oil level
You can continue driving for the time being but
you should check the engine oil level as soon as
possible
<^page
297.
- If the engine oil level is too Low, add more oil

^>page
298, Checking and topping up the en­
gine oil level.
- If the engine oil level is normal but the indica­
tor lamp stays on, drive to a qualified workshop
without delay and avoid high engine speeds.

ST
Engine oil sensor

3
Oil level sensor: system fault
The sensor for checking the engine oil level has

failed.
Drive to a qualified workshop soon and
have the fault rectified.

3
Oil level sensor: oil change required. Please
contact workshop
The engine oil level is too
high.

Drive to a qualified workshop without delay and
have the fault rectified.
CAUTION
Please observe the procedure described in the
Owner's Manual
^>page
298, Checking and
topping up the engine oil level.
f Engine warm-up
requested

Please warm up engine
34

Instruments and controls

CO

s
rN rN

•-i

00
Fuel has entered the engine oil due to low out­
side temperatures or frequent short trips. Drive
until the engine is warm to allow the fuel to
evaporate out of the engine oil. When doing so,
avoid high engine speeds, full acceleration and
heavy engine loads.

m
Fuel tank system
P3 Please refuel
When the indicator lamp lights up for the first
time and the message appears, there are still
about 7 litres (front-wheeL drive) or about
8.5
li­
tres (four-wheel drive) of fuel left in the tank.

IM
Please refuel immediately
If the indicator lamp lights up and the message
appears, the fuel tank is almost empty. Drive to a
filling station without delay.

E3
Tank system malfunction! Please contact
workshop
There is a malfunction in the tank system.
Drive to a qualified workshop without delay and
have the fault rectified.

S
Driver's door*
For more information about filling the tank,
refer to
=>page
290.

Washer fluid level
Please add washer fluid
With the ignition switched off, top up the fluid
for the windscreen washer and headlight washer

system*
^>page
303.

!
Windscreen wipers
Windscreen wiper defective
There is a malfunction in the windscreen wipers.
Drive to a qualified workshop without delay and
have the fault rectified.

E]
Driver's door: fault. Shift to P before leaving
vehicle. See owner's manual
A malfunction has occurred in the driver's door.
Move the selector lever to position P (automatic
gearbox) to hold the vehicle.
Drive to a qualified workshop soon and have the
fault rectified.

- Bulb monitor
If the indicator Lamp
jjjj
Lights up, a bulb has

failed.
The message indicates the location of the

bulb.

Have the bulb replaced without delay.
Vehicle lights: malfunction!
There is a fault with the headlights or light

switch.
Drive to a qualified workshop soon and
have the fault rectified.

/\
WARNING
Bulbs are sensitive to pressure. The glass can
break when you touch the bulb, causing in­
jury.

ip
Dynamic headlight range control
Applies to: vehicles with dynamic headlight range control

13
Headlight range control: system fault!
There is a malfunction in the dynamic headlight
range control which may cause other road users
to be dazzled.
Drive to a qualified workshop without delay and
have the fault rectified.

•D
Audi adaptive light
Applies to: vehicles with Audi adaptive light

US
Audi adaptive light: system fault!
There is a malfunction in the adaptive light. The
dipped beam headlights will still be working nor­
mally.
Drive to a qualified workshop soon and have the
fault rectified.
35

Doors and windows
Doors and windows
Central locking system
Accidental lock-out
To
prevent
yourseLf from being locked out, only
lock the vehicle when the remote control key is
not in the vehicle and all of the doors and the
boot lid are closed.
The central locking system prevents you from be­
ing locked out of the vehicle in the following sit­
uations:
- When the driver's door is open, you cannot Lock
the vehicle by pressing the
M
button on the re­
mote control key or touching the locking
sen­

sor* on one of the doors.
- The boot lid will be released again automatical­
ly if the convenience key* that was last in use is
left inside the boot when the boot lid is closed.
- If the convenience key* that was last in use is
detected in the vehicle, it is not possible to lock
the vehicle from the outside.
A WARNING
- Always take the key with you when leaving
the vehicle - even if
you
only intend to be
gone for a short time. This is especially im­
portant if children are left in the car. They
might otherwise be able to start the engine
or use power-operated equipment such as
the electric windows - this could lead to in­

juries.

- Locked doors could delay assistance in an
emergency, potentially putting lives at risk.
Do not leave anyone (especially children) in
the vehicle.
© Note
- Never leave any valuable items in the
vehi­

cle unattended. Even a locked vehicle is not
a safe.
- When you lock the vehicle, the LED on the
driver's window sill flashes. If the LED is
still on about 30 seconds after the vehicle is

locked,
the central locking system is not
working properly. You should have the
mal­

function repaired by
a
qualified workshop.
Description
The vehicle can be locked and unlocked via the
central locking system. You can use any of the

following:

- Remote control key
^>page
39, or
- Sensors in the front door handles*

cépage
39, or
- Lock on driver's door
^>page
41
- Interior central locking switch
^>page
40
Turn signals
The turn signals will flash twice when the vehicle
is unlocked and once when the vehicle is locked.
If the turn signals do
not
flash, the ignition may
still be on or one of the doors, the bonnet or the
boot lid may still be open.
Automatic locking function (Auto Lock)
The Auto Lock function Locks the doors and the
boot lid when the vehicle exceeds a speed of
about 15 km/h.
The vehicle is unlocked again immediately when
the ignition key is removed, the unlock button on
the central locking switch is pressed or one of the
interior door handles is pulled. The Auto Lock
function can be switched on and off in the info­
tainment system
^> page
41.
In the event of an accident in which the airbags

inflate,
the doors will be automatically unlocked
to facilitate access and assistance.
Selecting which doors are unlocked with the
remote control
When you lock the vehicle, the central locking
system will lock the doors and the boot lid. When
you unlock the vehicle, the central Locking system
will unlock either the driver's door
only,
or all the
locks on the vehicle, depending on the setting
you have selected on the infotainment system

^
<=> page
41.
o

rN
.-i
o

37

Doors and windows
Set of keys



service work is required. This also applies to
vehicles with convenience key*.

Fig.
21 Keys supplied with the vehicle
Remote control keys
The remote control key can be used to lock and
unlock the car. Press the release button
OFig.
21
-arrow- to make the key spring out of the handle
and to fold it back in.
Number of keys
You can check how many keys are initialised for
your vehicle using the infotainment system. To
do so, select:
|MENU|
button > Car
>
left control
button
>
Servicing & checks
>
Car information.
This feature enables used car buyers to make
sure they have received all of the keys.
Replacing a key
If
you
should lose a key, please contact an Audi
dealer. Have the remote control coding for that
key deactivated.
For
this purpose you should
bring all available keys with you. It is also impor­
tant to notify your insurance company if
a
key has
been lost.
Electronic immobiliser
The immobiliser is designed to prevent unauthor­
ised persons from driving the vehicle. It may not
be possible to start the engine with the key if
there is another ignition
key
from a different
make of vehicle on the same key
ring.

Data stored on remote control key
Data related to the service and maintenance of
the vehicle are stored continuously on your re­
mote control key. Your Audi dealer can read out
the data and will then be able to tell you what
The function of the remote control key may
be impaired by interference from other
near­

by radio signals (for example from a mobile
telephone or TV transmitter) if these are in
the same frequency range.
LED and battery for the remote control key

Fig.
22 Remote control key (rear): Opening the cover
LED on remote control key
The LED on the remote control key lights up
when you press the buttons.

•
The LED should flash once when you press one
of the buttons briefly.

•
The LED should flash repeatedly when you
press and hold one of the buttons (convenience
open/close).

•
If the LED does not flash, the battery in the re­
mote control key is flat. In addition, the indica­
tor lamp |y will light up and the message Re­
mote control key: please change key battery
will appear. Replace the battery in the remote
control key.

Replacing
the battery for the remote control
key
• Use a coin to lever the cover (2) off the key
®
=>
Fig.
22.

•
Insert the new battery with the "+"
symbol
fac­
ing up.

•
Press the cover back onto the key until it clicks
into place. •
38

Doors
and
windows
Child Locks
Applies to: vehicles with electric/mechanical child lock

The
child locks disable
the
rear windows and pre­
vent the rear doors from being opened from
the

inside.
Driver message
in the
instrument cluster
display

Fig.
33
Detail
of
the driver's door: Controls

Fig.
34
Rear door: Child lock
Vehicles with
H
button
• To activate/deactivate the interior door handle
and electric window switch on each
of
the rear

doors,
press the left/right button
\±\
on
the

driver's
door
(T)^Fig.
33.
The LED
in
the but­
ton will light up
or
go out.
• To activate/deactivate the child locks on both

sides,
press the
B
buttons one after the other.
Vehicles with
M
button

•
To activate/deactivate the electric window
switches on the rear doors, press the
\M
button
on the driver's door
© •=>
Fig.
33.
The LED in
the

button will light up
or
go
out.

•
To activate/deactivate the interior door handle
in addition, open the corresponding rear door
and use the car key
to
turn the key-operated
switch
in
the direction
of
the arrow
(or
in
the

opposite direction)
^>Fig.
34.

LMJ
Child lock: fault. Please contact workshop
There
is
a malfunction
in
the child lock. Press
the

1*1/51
button again.
If the message remains displayed, drive
to a

qualified workshop soon and have the fault
recti­

fied.

A WARNING
- Always take the key with you when Leaving
the vehicle
-
even
if
you
only intend
to be

gone
for
a short time. This
is
especially im­
portant
if
children are left in the car. They
might otherwise be able
to
start the engine
or use power-operated equipment such
as

the electric windows
-
this could lead
to
in­

juries.

-
If
there
is
a malfunction
in
the child lock,
it

may be possible
to
open
the
rear doors from
the inside
-
risk
of
accident!
Electric windows
Controls

The
driver can operate
all the
electric windows.

^^S

MB-®

hjHi)

Fig.
35 Driver's door: Controls for electric windows (exam­
ple)

All electric windows have two-stage switches:
Opening/closing the windows

•
Press/pull the switch briefly
to
the second stop:
the window will automatically open/close
all

the way. The window will stop moving immedi­
ately
if
the switch
is
operated again.
•

46

Doors and windows

CO

s
rN rN

•-i

00
• To set an intermediate position,
press/pulL
the
switch to the first position until the window has
reached the desired position.
Switches for electric windows

(T)
Front left
(2) Front right
(D
Rear
left
(4) Rear right

/\
WARNING
- Always take the key with you when Leaving
the vehicle - even if
you
only intend to be
gone for a short time. This is especially im­
portant if chiLdren are left in the car. They
might otherwise be able to start the engine
or use power-operated equipment such as
the electric windows - this could lead to in­

juries.

- Always be careful when closing the
win­

dows.
Careless use of the electric windows
can cause severe injuries.
- When locking the vehicle from the outside,
make sure that nobody is inside the vehicle,
as the windows cannot be opened from the
inside in an emergency.
© Note
The windows can be operated for about ten
minutes after the ignition has been switched
off. The window switches are only deactivated
when the driver's door or the front passeng­
er's door is opened.
Convenience open/close function
Applies to: vehicles with convenience open/close function
All the windows and the panorama sun
roof*
can
be opened and closed together.
Convenience open function

•
Press and hold the
\§\
button on the remote
control key until all the windows and the panor­
ama sun roof* have reached the desired
posi­

tion.

Convenience close function

•
Press and hold the
\M
button on the remote
control key until all the windows and the panor­
ama sun roof* are closed
c>^.
Or:
• Applies to vehicles with convenience key: Touch
and keep your hand in contact with the sensor
on one of the front door handles until
all
the
windows and the panorama sun roof* are

closed.
Do not
rest
your hand on the door
han­

dle while this is happening.
This function can be switched
on/off
via the info­
tainment system
•=>
page 41.
A WARNING
-Take care when closing the windows and the
panorama sun roof*. Careless or uncontrol­
led use can cause injuries.
- For safety reasons, you should only use the
remote control key to open and close the
windows and panorama sun roof* within
about 2 metres of the vehicle. To avoid
inju­

ries,
always keep an eye on the windows and
the panorama sun roof* when pressing the

m
button to close them. The windows and
sun roof stop moving as soon as the 0 but­
ton is released.
What to do after a malfunction

You
can reactivate the one-touch open and close
function if it fails to operate.

•
Pull and hold the electric window switch until
the window is fully closed.

•
Release the switch and then pull it again for at
least one second.
47