wheel AUDI Q2 2021 Owner´s Manual

Instruments and controls

-Totaljourney
memory summary
- Energy consumers
^>page
20
- Driver assistance
^>page
104
- Traffic sign recognition
<=>page
108
The single journey memory processes the infor­
mation on
a
journey from the time the ignition is
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the
single
journey memory, the totaljour-
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­

formation.

Fuel consumption
The current fuel consumption can be shown in a
bar display
^>Fig.
15. The average fuel consump­
tion from the single journey memory can also be

displayed.
If the barturns green, yourvehicle is
saving fuel using the following function:
- Recuperation: Electrical energy can be stored in
the battery (recuperation) if the vehicle is trav­
elling downhill or coasting in gear (overrun). In
this case, the bar will move towards the
Q

symbol.

- Active Cylinder Management*: The engine au­
tomatically shuts down two cylinders when per­
formance demand is low and certain other
con­

ditions have been met. This process is imper­
ceptible to the occupants. The driver message

2-cylinder
mode will appear if the average fuel
consumption display
^>Fig.
15 is selected in the
instrument cluster. The cylinders are reactiva­
ted under heavier load conditions.
Energy consumers*
In the Energy consumers view, auxiliary equip­
ment currently affecting the vehicle's fuel
con­

sumption is listed. The display shows up to
three energy consumers. The energy consumer
drawing the most power appears at the top of
the list. If more than three energy consumers are
switched on, the ones currently using the most
power are displayed. In addition, a scale
indi­

cates the overall current fuel consumption of all
energy consumers.
Economy tips
Applies to: vehicles with Audi drive select and efficiency mode
In efficiency mode, economy tips are shown
briefly on the instrument cluster display in cer­
tain situations where fuel economy is affected.
By following these economy tips, you can save

fuel.

To clear an economy tip from the display immedi­
ately, press the left thumbwheel on the multi­
function steering wheel.
To activate/deactivate economy
tips:
Select the
following on the infotainment system:
|MENU|

button > Car
>
Audi drive select. Select: efficien­
cy
>
right control button > Economy tips.
© Note
- The date, the time and the time/date dis­
play format can be changed via the infotain­
ment system
^page
255.
- The economy tips are not always displayed
in every conceivable situation, but are delib­
erately spaced out over time.
- Once you have cleared an economy tip from
the display, it will not appear again until the
next time you switch on the ignition.
On-board computer (analogue instrument
cluster)
Applies to: vehicles with analogue instrument cluster
15:50

0
6,0

Fig.
16 Instrument cluster: Consumption display
Resetting values to zero

•
Press the
[Hi
button on the multi-function
steering wheel and select On-board computer
or Efficiency program from the menu. •
20

Instruments and controls

CO

<
o

IV
tN
I-I
00
• To reset the figures in the selected memory to

zero,
press the left
thumbwheel (Î) •=>page
18,
Fig. 13 on the multi-function steering wheel for
one second.
Calling up vehicle functions
• Call up the first tab (on-board computer) using
the
0E]
button on the multi-function steering

wheel.

•
Press the
@
button on the multi-function
steering wheel and select Vehicle functions
from the menu.
The equipment installed on your vehicle deter­
mines which of the following displays are availa­

ble:

- On-board computer fl, B
opage
21
- Efficiency program
3
<^page
21
- Digital speedometer
- Assists
cépage
104
- Traffic signs
^>page
108
- Reduced display
On-board computer
On the on-board computer you can call up the
following displays in turn by scrolling the left
thumbwheel on the multi-function steering

wheel:

- Date
•=>
page 255
- Range
- AdBlue range*
^>page
292
-Short-term
memoryD

- Average fuel consumption
- Long-term memory B
The single journey memory processes the infor­
mation on
a
journey from the time the ignition is
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the single journey memory, the
total
jour­
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­

formation.

The following additional display may be available
in the on-board computer, depending on the ve­
hicle equipment:
- Active Cylinder Management: The engine auto­
matically shuts down two cylinders when per­
formance demand is low and certain other
con­

ditions have been met. This process is imper­
ceptible to the occupants. The driver message

2-cylinder
mode will appear if the current or
average fuel consumption display
oFig.
16 is
selected in the instrument cluster. The cylin­
ders are reactivated under heavier load condi­

tions.

Efficiency program
3

Applies to: vehicles with efficiency program
The efficiency program can help to save
fuel.
It
evaluates fuel efficiency data, shows a list of aux­
iliary equipment affecting fuel consumption, and
suggests gear changes. It also provides economy
tips for saving
fuel.

The efficiency program uses the trip and fuel
con­

sumption data from the short-term memory.
When you clear the data from the efficiency pro­

gram,
the values in the short-term memory are
reset to zero.
The following additional displays are available in
the efficiency program, depending on the vehicle
equipment:
- Advanced gear-change indicator: The advanced
gear-change indicator is based on the same
log­

ic as the "regular" gear-change indicator. The
"regular" gear-change indicator disappears
from the display when the advanced gear-
change indicator appears
^>page
14.
- Energy consumers: The efficiency program
shows a List of energy consumers currently af­
fecting the vehicle's fuel consumption. The dis­
play shows up to three energy consumers. The
energy consumer drawing the most power ap­
pears at the top of the list. If more than three
energy consumers are switched on, the ones
currently using the most power are displayed.
In addition, a scale indicates the overall current
fuel consumption of all energy consumers.
- Economy
tips:
Economy tips will automatically
appear intermittently in the efficiency program •
21

Instruments and controls
in certain situations. By following these econo­
my tips, you can save
fuel.
To clear an economy
tip from the display immediately, press any of
the controls on the multi-function steering

wheel.

The date, the time and the time/date display
format can be changed via the infotainment
system
•=>
page 255.
Radio
Important: Radio mode must be activated

^>page
228, and the radio/media tab must be

displayed.

•
Press the
HH
button or the left control button

^>page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To set the waveband: Select and confirm the

waveband.

- To tune to a station from the memory list*:
Select Memory
>
desired radio station.
- To tune to a station from the station list*: Se­
lect and confirm a radio station.
- To tune to a station from the favourites list:
Select Favourites > desired radio station.
- To call up a media source: Select and confirm
To media.
Other settings
Applies to: vehicles with Audi virtual cockpit
- SeLect: right control button > desired
entry.

The following settings are available depending
on which function is selected:
- Update station list*: see
<=>page
232.
- Detailed station information: See

opage
232.
Media
Important: A media drive must contain audio/
video files
^page
235, and the radio/media tab
must be displayed.

•
Press the
\M
button or the left control button

^page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To select a media source: Select and confirm a
media source, e.g. "SD
card".

- To play an audio/video file: Select and confirm
a track/file.
-To pause/resume playback: Press the right

thumbwheel (D^poge
17, Fig. 12. To continue
playback, press the right thumbwheel again.
- To restart playback of an audio file: Select the
track currently playing if it is not already selec­
ted and press the left thumbwheel.
Applies to: vehicles with analogue instrument cluster
- To switch to the radio: Select and confirm a
waveband (e.g. FM).
Applies to: vehicles with Audi virtual cockpit
- To switch to radio: Select and confirm To radio.
- To call up detailed track information: SeLect
the right control button > Detailed track infor­

mation.
For more information, please refer to

tapage
246.
® Note
- The MMI media drives do not support DRM-
protected files; these files are marked with
the
symbolS.

- Please note that when you are using the
driver information system to control play­
back within a media source, only the playlist
selected on the MMI control console can be
played
^>page
244.
- Always note the information on the info­
tainment display. It may be necessary to
use the MMI control console to operate cer­
tain functions.
22

Instruments and controls

CO

<
O
rN
r>

I-I

00
Telephone
Applies to: vehicles with telephone
Important: A mobile phone must be connected
to the MMI
^>page
173, and the telephone tab
must be displayed.

•
Press the
\M
button or the left control button

^>page
16, depending on the equipment in
your vehicle.
The following functions are available on the driv­
er information system, depending on the vehicle
equipment:
- To call a contact: Select and confirm Call list /
Favourites / Directory. Select and confirm a
contact.
- Directory contacts: Only directory contacts for
which a telephone number is stored are dis­
played in the driver information system. If sev­
eral telephone numbers are stored for one
con­

tact, the list of stored telephone numbers is
displayed first when the contact is selected. For
more information on the symbols displayed, re­
fer to
^>page
185.
- Call list: The call lists contain all received,
placed and missed calls.
- Caller information*: Depending on whether the
caller is stored in the directory and whether the
telephone number is transmitted with the
call,

the name, the telephone number or Unknown

wilL
appear on the display of the driver informa­
tion system.
Functions for an incoming call
- To answer a
call:
Press the left thumbwheel
when there is an incoming
call.

- To ignore a
call:
Select and confirm Ignore
when there is an incoming
call.

- To end a
call:
SeLect and confirm End
call.

Functions during a call
Applies to: vehicles with analogue instrument cluster
- To make a further
call:
Select Hold >
\M\
button
> Directory or Call list
>
entry in
list.

- To answer a further call when you are talking
on the phone and have another call on hold:
Select and confirm Replace. The current call
will be replaced by the incoming
call.

Applies to: vehicles with Audi virtual cockpit
- To make a further
call:
Select Hold > left
con­

trol button > Directory or Call list
>
entry in

list.

- To answer a further call when you are talking
on the phone and have another call on hold:
Select and confirm Answer. The current call will
be replaced by the incoming
call.

Other functions are:
Microphone off: If
you
select and confirm this

option,
the caller will no longer be able to hear

you;
you will still be able to hear the caller.
Hold/Resume: You can put
a
call on hold and re­
trieve
it
from the hold queue later.

Switch:
You can switch between two phone calls
(one of them will be on hold at any given time).
Select End call to end whichever call is active.
The call on hold will remain in the hold queue
and can be retrieved by selecting Resume.
Conference: Up to five callers and one caller on
hold can take part in a conference (depending on
the mobile network provider). To set up a further

call,
select Hold to place all the members of an
existing conference on
hold.
You can then press
the left control button to place another call to a
contact in the directory or the call list. Select Re­
sume if
you
want to retrieve all participants in an
existing conference from the hold queue.
- The functions of the telephone can be oper­
ated using the multi-function steering
wheel only if the telephone equipment was
installed at the factory.
- The functions of the telephone depend on
your mobile phone and whether they are
supported
by
your mobile network service
provider.
- The option Call waiting must be activated
on your mobile phone and on the MMI for
you to be made aware of incoming calls dur­
ing a conversation. The call options depend
on your mobile network service provider.
For more information, contact your service
provider.
23

Instruments and controls

CO

s
rN rN
I-I

00
Street view when route guidance is started
Applies to: vehicles with navigation system and analogue in­
strument cluster

f»
Bayern
3
:OB16a/Inqolstadt

Fig.
18 Example: Lane change in instrument cluster

> 89.9 MHz

Fig.
19 Example: Turn-off in instrument cluster
Important: A destination must have been en­
tered
^>page
208, the route guidance function
must have been started, and the navigation tab
must be displayed.
The following information is displayed on the
driver information system, depending on the
equipment installed in your vehicle:

(T)
Distance to next manoeuvre

@
Distance to destination/stopover
(D Estimated time of arrival
(4) Name of motorway, major road or street you
are driving on. If the symbol
O
is displayed
in front of the street name, you are being di­
rected to turn into the street.
(5) Arrow indicating direction of upcoming
turn-

off
(?) Lane recommendation
(7) If an arrow is displayed, a bar graph will also
appear. The fewer bars are displayed, the
shorter the distance to the turn-off point.
The following functions are available when route
guidance is active:
- To have the last navigation cue repeated:
Press
the S
button.
- To adjust the volume of the navigation cues:
Scroll the right thumbwheel up/down while a
navigation cue is being played.

A
WARNING
The route calculated by the navigation system
is a recommendation of how best to reach a
destination. Pay attention to traffic lights, no-
stopping signs, lane change restrictions,
one­

way streets, etc.

(T)
Note
- Also refer to
^>page
10, Controls at a
glance.
- An exclamation mark
"I"
in front of the
street name indicates that the navigation
data of the MMI system do not contain all
the information on this street or street sec­

tion.
Pay attention to traffic rules such as
one-way streets or pedestrian zones.
Head-up display
Applies to: vehicles with head-up display

Fig.
20 Dashboard: Button for head-up display
The head-up display projects certain warnings
and selected information from driver assist func­

tions*
and the navigation system* into the driv­
er's area of vision.
Switching on/off
• To switch the head-up display on/off, press the

^button.
•
25

Instruments and controls
Height adjustment
The height of the head-up display can be adjus­
ted to your individual requirements.

•
Sit in the correct position in your seat

•=>
page 265.
• Turn the
button to adjust the display.
Settings on infotainment system

•
Select the following on the infotainment sys­

tem:
IMENU|
button > Car
>
left control button
> Driver assist
>
Head-up display.
Display contents
The settings on the infotainment system allow
you to specify which information is shown in the
display. Possible options include navigation mes­
sages*, adaptive cruise control* and camera-
based traffic sign recognition*.
The display of certain information and some of
the red warning lamps cannot be deactivated on
the infotainment system.
Brightness
You can adjust the brightness of the display via
the infotainment system. In addition, the display
brightness is reduced automatically as the
day­

light starts to fade. The basic level of brightness
is determined by the instrument lighting setting

•=>
page 53.
© CAUTION
Do not place any objects over the opening for
the head-up display to avoid scratching the
glass cover.
© Note
- The display may be harder to see in unfav­
ourable light conditions or if
you
are wear­
ing polarised sunglasses.
- To be able to see the display as clearly as
possible, adjust the position of your seat
and the height setting for the head-up dis­
play.
- Notes on cleaning
^tab.
Cleaning the inte­
rior on page 314.
Warning and indicator
Lamps
Description
The warning and indicator lamps light up or flash
in the instrument cluster to indicate functions or

faults.

Some of the warning and indicator lamps may be
accompanied by a driver message. The warning
display will be accompanied by the corresponding
warning chime. The warning/indicator lamps and
driver messages on the instrument
duster
dis­
play can be masked by further displays. You can
have them displayed again on the driver informa­
tion system* by calling up the second tab (driver
messages) via the
\<±\
button on the multi-func­
tion steering wheel. If several malfunctions have

occurred,
you can use the Left thumbwheel to
scroll through them on the display.
Some of the warning lamps may be displayed in
different colours.

âs
Central warning/indicator lamps
If the warning/indicator lamp
|g or pq
lights

up,
observe the additional information on the in­
strument cluster display.

Applies
to: vehicles with monochrome display
If
a
driver message appears and a central warn­
ing [amp
Kfl/central
indicator
lamp^S
lights up,
the central warning/indicator lamp indicates the
priority level of the warning. If
a
white indicator
lamp also appears, the central warning/indicator
lamp indicates its actual colour. For example, if

g
lights up with
H.
read the description for
Overview
When you switch on the ignition, some of the
warning and indicator lamps Light up briefly to
show that the associated systems are working
properly. These systems are marked with a
•/
in
the following tables. If one of these warning/in­
dicator lamps does not light up, there is a fault in
the associated system. •
26

Instruments and controls

CO

s
rN rN

•-i

00
Fuel has entered the engine oil due to low out­
side temperatures or frequent short trips. Drive
until the engine is warm to allow the fuel to
evaporate out of the engine oil. When doing so,
avoid high engine speeds, full acceleration and
heavy engine loads.

m
Fuel tank system
P3 Please refuel
When the indicator lamp lights up for the first
time and the message appears, there are still
about 7 litres (front-wheeL drive) or about
8.5
li­
tres (four-wheel drive) of fuel left in the tank.

IM
Please refuel immediately
If the indicator lamp lights up and the message
appears, the fuel tank is almost empty. Drive to a
filling station without delay.

E3
Tank system malfunction! Please contact
workshop
There is a malfunction in the tank system.
Drive to a qualified workshop without delay and
have the fault rectified.

S
Driver's door*
For more information about filling the tank,
refer to
=>page
290.

Washer fluid level
Please add washer fluid
With the ignition switched off, top up the fluid
for the windscreen washer and headlight washer

system*
^>page
303.

!
Windscreen wipers
Windscreen wiper defective
There is a malfunction in the windscreen wipers.
Drive to a qualified workshop without delay and
have the fault rectified.

E]
Driver's door: fault. Shift to P before leaving
vehicle. See owner's manual
A malfunction has occurred in the driver's door.
Move the selector lever to position P (automatic
gearbox) to hold the vehicle.
Drive to a qualified workshop soon and have the
fault rectified.

- Bulb monitor
If the indicator Lamp
jjjj
Lights up, a bulb has

failed.
The message indicates the location of the

bulb.

Have the bulb replaced without delay.
Vehicle lights: malfunction!
There is a fault with the headlights or light

switch.
Drive to a qualified workshop soon and
have the fault rectified.

/\
WARNING
Bulbs are sensitive to pressure. The glass can
break when you touch the bulb, causing in­
jury.

ip
Dynamic headlight range control
Applies to: vehicles with dynamic headlight range control

13
Headlight range control: system fault!
There is a malfunction in the dynamic headlight
range control which may cause other road users
to be dazzled.
Drive to a qualified workshop without delay and
have the fault rectified.

•D
Audi adaptive light
Applies to: vehicles with Audi adaptive light

US
Audi adaptive light: system fault!
There is a malfunction in the adaptive light. The
dipped beam headlights will still be working nor­
mally.
Drive to a qualified workshop soon and have the
fault rectified.
35

Driving
Steering
Adjusting the steering wheel position
The height and reach of the steering wheel can
be adjusted as required to suit the
driver.

Fig.
68 Steering column: Lever for steering column adjust­
ment

•
Push the Lever
^>Fig.
68 down
<=> /\.
•
Move the steering wheel to the desired
posi­

tion.

•
Then push the lever towards the steering
col­

umn until the catch engages.
WARNING
- Never adjust the position of the steering
wheel when the vehicle is moving - this
could cause an accident.
- Press the lever upwards so it is secure and
so that the position of the steering wheel
cannot shift unexpectedly while the vehicle
is moving - risk of accident!
Starting and stopping
the engine (vehicles with
ignition Lock)
Starting the engine
Applies to: vehicles with ignition lock
Insert the key in the ignition lock to switch on
the ignition and start the engine.

Fig.
69 Ignition lock: Ignition key positions
Switching the ignition on/off

•
To switch on the ignition, turn the ignition key
to position ®. Vehicles without start/stop sys­

tem*:
The rev counter needle will move to the
READY position.
• To switch off the ignition, turn the ignition key
to position ©. The rev counter needle will
move to the OFF position.
Diesel engines are automatically preheated when
you switch on the ignition.
Starting the engine

•
Manual gearbox: Press the clutch pedal all the
way down and move the gear lever into neutral.

•
Automatic gearbox: Press the brake pedal and
move the selector lever to position P or N.

•
Turn the ignition key briefly to position @. The
ignition key automatically returns to position
®. Do not press the accelerator.
Applies to: vehicles with diesel engine

•
The engine may take a few seconds Longer than
usual to start on cold days. Please keep your
foot on the clutch pedal (manual gearbox) or
brake pedal (automatic gearbox) until the en­
gine starts. The indicator Lamp
E g
lights up
while the glow plugs are preheating.
74

Driving

CO

<
O
rN
iv
rN
•-i

00
Electrical components with a high power
con­

sumption are switched off temporarily while you
start the engine.
If the engine fails to start immediately, switch
off the starter by turning the ignition key to
posi­

tion (5) and try again after about 30 seconds.

Start/stop
system*

Please note the information on
^>page
79,
Start/stop system.
A WARNING
- Never run the engine in confined spaces.
The exhaust gases are toxic - risk of poison­

ing!

- Never remove the key from the ignition
while the vehicle is moving. The steering
lock would engage, and you would not be
able to steer the car - risk of accident!
© CAUTION
Avoid high engine speeds, full throttle and ex­
treme load conditions until the engine has
reached its normal operating temperature;
otherwise this can damage the engine.
© For the sake of the environmen
Do not warm up the engine by running it with
the car stationary. You should drive off imme­
diately whenever possible. This will help avoid
unnecessary exhaust emissions.
© Note
- If it is difficult to turn the ignition key to po­
sition ®, move the steering wheel (to take
the load off the steering lock mechanism)
until the key turns freely.
- Any noises which may be heard when the
engine is started are quite normal and no
cause for concern.
Switching off the engine
Applies to: vehicles with ignition lock
Switching off the engine

•
Stop the vehicle.

•
Turn the ignition key to position
@.
The rev
counter needle will move to the OFF position.
Engaging the steering lock
Important: The selector lever must be in position
P (automatic gearbox*).

•
Remove the ignition key while it is in position

(§) ^>page
76, Fig. 70
=> A
•
Turn the steering wheel until you hear the
steering lock engage.
The steering lock acts as a theft deterrent.

A,
WARNING
- Never switch off the engine until the vehicle
is stationary. Otherwise you may not have
the full benefit of the brake servo and pow­
er steering. You may need more strength to
steer and brake the vehicle than you nor­
mally would. This would mean a greater risk
of accidents and serious injury, because you
cannot steer and brake in the normal
man­

ner.
- Never remove the key from the ignition
while the vehicle is moving. The steering
lock could engage suddenly, and you would
not be able to steer the car.
- Always take the key with you when you leave
the vehicle. Otherwise the engine can be
started or power-operated equipment such
as the electric windows can be used. This
could result in serious injury.
- When parking, always move the selector
lever to position
P
to prevent the vehicle
from rolling back accidentally.
© CAUTION
If the engine has been working hard
fora
long

time,
there is a risk of heat building up in the
engine compartment after the engine has
been switched off; this could cause engine
damage. For this reason, you should Leave the
engine idling for about 2 minutes before
switching
it
off.
75

Driving
©
y
Note
After the engine is stopped, the radiator fan
may remain on or turn itself back on for up to
10 minutes, even if the ignition is switched
off. This may occur for the following reasons:
- Residual heat has raised the coolant
tem­

perature.
- Direct sunlight has additionally heated up
the engine compartment while the engine is

warm.

- Applies to vehicles with diesel particulate
filter: The emission control system is hot
because of the regeneration process, even
though the engine has
not
yet reached oper­
ating temperature.
Starting and stopping
the engine (vehicles with
convenience key)
Starting the engine
Applies to: vehicles with convenience key
You can use the ISTART ENGINE STOP| button to
switch on the ignition and start the engine.

Fig.
70 Centre console: START ENGINE STOP button
Starting the engine

•
Manual gearbox: Press the clutch pedal all the
way down and move the gear lever into neutral.

•
Automatic gearbox: Press the brake pedal and
move the selector lever to position P or N.

•
Press the ISTART ENGINE
STOP!
button briefly
to start the engine.
Applies to: vehicles with diesel engine

•
The engine may take a few seconds longer than
usual to start on cold days. Please keep your
foot on the clutch pedal (manual gearbox) or
brake pedal (automatic gearbox) until the en­
gine starts. The indicator Lamp
E 3
lights up
while the glow plugs are preheating.
Electrical components with a high power
con­

sumption are switched off temporarily while you
start the engine.
If the engine fails to start immediately, switch
off the starter by pressing the
ISTART
ENGINE
STOPI
button once more and try
again after about 30 seconds.
Switching the ignition on/off
If you only wish to switch on the ignition and do
not want to start the engine as
well,
proceed as
follows:

•
Press the ISTART ENGINE STOP| button with­
out pressing the clutch (manual gearbox) or
brake pedal (automatic gearbox). Vehicles
without start/stop system*: The rev counter
needle will move to the READY position.

•
To switch off the ignition, press the button

again.
The rev counter needle will move to the
OFF position.
Diesel engines are automatically preheated when
you switch on the ignition.
If the indicator lamp
£21
flashes and the message
Please move steering wheel appears when you
switch on the ignition, the steering wheel is

locked.
In this case, turn the steering wheel
slightly
to
the left/right.
Start/stop system*
Please note the information on
<^>page
79,
Start/stop system.
WARNING
Never run the engine in confined spaces. The
exhaust gases are toxic - risk of poisoning!
© CAUTION
Avoid high engine speeds, full throttle and ex­
treme load conditions until the engine has
reached its normal operating temperature;
otherwise this can damage the engine. •
76