warning engine AUDI Q2 2021 Owner´s Manual

Driving

•
Briefly pull the selector lever back from
posi­

tion D/S to select position S, or move the selec­
tor lever to the right into the tiptronic gate, or
select dynamic mode in drive select*

^>page
131.

•
Press the brake pedal firmly with your
left
foot
and hold it down for at Least one second.

•
At the same time, press the accelerator all the
way down with your right foot until the engine
revs are high and steady.
• Take your
left
foot
off
the brake.
A WARNING
- Always adapt your driving style to the traffic
conditions.
- Only use the launch control programme
when road and traffic conditions permit,
and make
sure
your manner of driving and
accelerating the vehicle does not inconven­
ience or endanger other road users.
- Please note that the driven wheels may
start to spin when the off-road mode is
switched on, causing the vehicle to Lose

grip,
in particular on slippery or wet roads -
danger of skidding!
- When acceleration has been completed, you
should deactivate the off-road mode again
by briefly pressing the
|flQFF|
button.
© Note
- The gearbox may be hot after you have used
the launch control programme. In this case,
the programme may not be available for
several minutes. The programme will be
available again after
a
cool-down period.
-Accelerating with the launch control pro­
gramme places a heavy load on all parts of
the vehicLe. This can result in increased wear
and tear.
Gearbox malfunction
Applies to: vehicles with automatic gearbox
| Gearbox malfunction! Please stop the vehi­
cle and select P
There is a malfunction in the gearbox. Park the
vehicle safely and do not drive on. Obtain profes­
sional assistance.
| Gearbox overheating! Please stop the vehi­

cle.

The gearbox is overheating and could be dam­

aged.
Stop the vehicle and let the gearbox cool
down with the engine idling and the selector lev­
er in position P. If the warning lamp and the
message disappear, drive to a qualified workshop
soon and have the fault rectified. Do not drive on
if the warning lamp stays on and the message
does not disappear. Obtain professional assis­

tance.

E3
Gearbox malfunction: you can continue driv­
ing
Drive to a qualified workshop soon and have the
fault rectified.

S3
Gearbox malfunction: no reverse gear (you
can continue driving)
A gearbox malfunction has occurred. The gearbox
will switch to the back-up programme. The pro­
gramme will only move into certain gears or may
not be able to shift gears at all. The engine may

stall.
You can no longer engage reverse gear.
Drive to a qualified workshop without delay and
have the fault rectified.

jftj
Gearbox malfunction: you can continue driv­
ing in D until engine off
Park your vehicle well away from moving traffic.
Obtain professional assistance.

ty
Gearbox overheating: please adapt driving
style
You can continue driving at moderate speed. You
can resume normal driving if the indicator lamp
goes out.

LQ]
Gearbox: please press brake pedal and select
gear again
If
a
gearbox malfunction has occurred due to
overheating, this message will appear once the
gearbox has cooled down again.
92

Towing a trailer
Towing a trailer
Driving the vehicle with a
trailer or caravan
Technical requirements

The
towing bracket must comply with certain
technical requirements.
Your car is intended mainly for transporting pas­
sengers and luggage. However, if suitably equip­

ped,
it can also be used to tow a trailer or cara­

van.

If the car is supplied with a factory-fitted towing
bracket it will already have the necessary techni­
cal modifications and meet the statutory require­
ments.
A 13-pin socket is provided to make the electrical
connection between the car and the trailer. If the
trailer you wish to tow has a 7-pin plug, the nec­
essary adapter cable can be obtained from a spe­
cialist retailer.
If
a
towing bracket is to be fitted after the car is

purchased,
this must be done according to the in­
structions of the towing bracket manufacturer

^page
102.
A WARNING
If
a
towing bracket is retrofitted, the installa­
tion should be carried out by
a
qualified work­

shop.

- In particular in high outside temperatures it
is not possible to drive up long steep gradi­
ents without
a
suitable cooling system. The
engine would then overheat.
- Incorrect installation can result in a safety
risk.
Points to check before towing
There are a number of points which need to be
checked before towing a trailer or caravan.

*•
Observe the maximum permitted trailer
weights
^>page
342.
Trailer weights
Never exceed the maximum permitted trailer
weights.
If
you
do not load the trailer up to the maximum
permitted trailer weight, you can then climb cor­
respondingly steeper gradients.
The maximum trailer weights listed are only ap­
plicable for altitudes up to 1000 m above sea

level.
With increasing altitude the engine power
and therefore the car's climbing ability are im­
paired because of the reduced air density, so the
maximum trailer weight has to be reduced ac­
cordingly. The weight of the car and trailer must
be reduced by about 10% for every further
1000 m (or part thereof). This figure refers to
the combined weight of the (loaded) vehicle and
(Loaded) trailer.
The figures for the draw bar weight that appear
on the identification plate of the towing bracket
are for certification purposes only. The correct
figures for your specific model, which may be
lower than these figures for the towing bracket,
are given in the registration documents and in

•=>
page 343.
Drive select*
Please note that the
efficiency*
mode is not
available in towing mode.
Exterior lights
Before starting
a
journey, make sure that all the
lights for the trailer are working properly.
Distributing the load
Distribute loads in the trailer so that heavy ob­
jects are as near to the axle as possible. Loads
carried in the trailer must be secured to prevent
them slipping. A badly distributed load can also
affect handling. This can activate the trailer sta­
bilisation feature and cause the vehicle to reduce

speed.

Where possible, operate the trailer with the max­
imum permitted draw bar weight on the ball
joint of the towing bracket, but do not exceed the
specified limit. •
96

Towing a trailer
Requirements for correct functioning of the
trailer stabilisation system
If these conditions are not met in
full,
the trailer
stabilisation system will only intervene to a
limi­

ted extent or not at all
>=>
A-
- The electrical connection between the towing
vehicle and the trailer must be functioning cor­
rectly.
- The load on the trailer must be properly se­

cured.

- The tyre pressures on both the vehicLe and the
trailer must be adapted to the load that is be­
ing carried.
- Where possible, operate the trailer with the
maximum permitted draw bar weight.
- The trailer overrun brake must be set correctly.
This is important to ensure that the trailer can
be braked correctly, to avoid the vehicle and
trailer "jack-knifing" and to prevent excess
braking of the trailer.
- At low outside temperatures, both the towing
vehicle and the trailer should be fitted with
winter tyres.
A WARNING
It is essential that you adjust your speed to
suit the weather, road and traffic conditions.
Do not let the trailer stabilisation system
tempt you into taking any risks when driving -
this can cause accidents.
- The ESC and trailer stabilisation system
can­

not defy the Laws of physics. This should be
kept in mind, particularly on slippery and
wet roads and when towing a trailer with a
light Load.
- The trailer stabilisation system is function­

al,
regardless of whether the trailer has a
mechanical overrun brake or not.
- The trailer stabilisation system is not always
able to detect swaying of trailers with a
light load and will therefore not intervene.
- A trailer can still "jack-knife" on slippery
roads with little grip, even if the towing ve­
hicle is equipped with the trailer stabilisa­
tion system.
-Trailers with a high centre of gravity may
even tip over before they start to sway
side­

ways.

-If
you
are not towing a trailer,
but
the
trail­

er socket is being used (e.g. for an illumina­
ted bicycle rack), the trailer stabilisation
system may be activated in extreme driving
conditions.
- Please note the additional information and
warnings
^>page
98, Driving tips.
Driving tips
Driving with a trailer always requires extra care.
Weight distribution
Try to avoid towing a loaded trailer with an unla­
den vehicle. If this cannot be avoided, drive extra
slowly to allow for the unbalanced weight distri­

bution.

Speed
Normally, you must not exceed 80 km/h when
towing a trailer or caravan. However, if the
trail­

er/caravan is equipped with a trailer stabilisation

system,
you can drive at max. 100 km/h. Please
observe any other regulations applicable in the
country in which you are travelling.
The stability of the car and trailer is reduced with
increasing speed. For this reason it is advisable
not to drive at the maximum permissible top
speed in unfavourable
road,
weather or wind
con­

ditions. This applies especially on a downhill gra­
dient.
You should always reduce speed immediately if
the trailer shows the slightest sign of swaying.
Never try to stop the swaying by accelerating fur­
ther.
Always brake in good time. If the trailer has an
overrun brake, apply the brakes gently at first
and then firmly. This will prevent the jerking that
can be caused by the trailer wheels locking.
Change down in good time before going down a
steep hill so
that
you can use the engine braking
effect to slow down the vehicLe.
Swaying and pitching can be reduced by attach­
ing an extra stabiliser to the trailer. It should •
98

Towing
a
trailer

CO

< o rN
iv
rN
t-H
o < 00
have friction linings at the sides to prevent exces­
sive wear. Degrease and clean the ball joint be­
fore using a stabiLiser. The stabiliser can be pur­
chased and installed
at
a qualified workshop.
Electronic stabilisation control
The
ESC
-
in particular in conjunction with the
trailer stabilisation system
o^page
97 - makes
it

easier to stabilise a trailer
if it
starts to skid
or

sway. You should therefore keep the
ESC
switch­
ed on
at
all times.
Overheating
In hot weather, keep an eye on the coolant
tem­

perature gauge
^page
13. When climbing long
hills with the engine running fast in low gear, the
coolant temperature can increase. Reduce speed
immediately
if
the needle moves to the right end
of the scale. For information on the warning
lamp
||
refer to
opage
30.

Rear carrier systems
When using rear carrier systems (e.g. bicycle
racks) on the towing bracket,
it
is important not
to exceed the maximum load.
The total weight
of
the rear carrier system and
its

load must not exceed
75
kg for this vehicle. How­
ever,
it
is also important to observe the maxi­
mum permissible load for the rear carrier sys­

tem.

The greater the distance from the towing brack­
et, the smaller the maximum permissible Load
on

the rear carrier system. For this reason, you
should secure heavy objects as near as possible
to the towing bracket.
Note the instructions provided by the manufac­
turer of the rear carrier system.
Please make sure that the rear carrier system
is

approved for use on your vehicle.

l
Note
A WARNING
The use of an unsuitable rear carrier system
could cause severe damage
to
the towing
bracket. The towing bracket could then break
and cause an accident.
Degrease and clean the ball joint before using
a rear carrier system.

Removable towing
bracket

Introduction
Applies to: vehicles with removable towing bracket
Special care is required when fitting and remov­
ing the towing bracket.

Fig.
84 Luggage compartment:
Ball
joint for towing brack­
et (stowage example)
The removable ball joint attachment for the tow­
ing bracket is stored under the floor panel or in a
separate bag on the floor of the luggage com­
partment.
The ball joint can be fitted and removed by hand.
WARNING
Never use tools of any kind when fitting and
removing the ball joint. This could damage
the mechanism which locks the
ball
joint
in

place and impair its safety
-
risk of accident!
© Note
- Do not attempt to modify or repair the ball
joint or other towing bracket components.
- Should you have any difficulties when using
the towing bracket, or suspect that
it
is not
fitted properly, contact
a
qualified work­

shop.

- Before setting off, always check that the

ball
joint is secured properly
Opage
101.
99

Towing a trailer

CO

rN
rN

•-i

00
If a towing bracket is to be fitted after the car is

purchased,
this must be done according to the in­
structions of the towing bracket manufacturer.
The towing bracket is bolted to the body at the
securing points®
^F/'g.
93.
Qualified workshops are familiar with the meth­
od of installation and any modifications which
may be required for the cooling system.

/\
WARNING
If a towing bracket is retrofitted, the installa­
tion should be carried out by a qualified work­

shop.

- A towing bracket that is not fitted properly
constitutes an accident risk.
- For your own safety, please observe the in­
structions provided by the manufacturer of
the towing bracket.
©
1
CAUTION
- If the connector socket is not fitted correct­
ly, this could cause damage to the vehicle's
electrical system.
- In particular in high outside temperatures it
is not possible to drive up Long steep gradi­
ents without a suitable cooling
system,

there is a risk of damaging the engine.
103

Driver assist systems
Driver assist systems Cruise
control,
system
Speed warning function
Applies to: vehicles with speed warning function
The speed warning function can
help
you keep
below a pre-set maximum speed. It can be set,
changed and deleted on the infotainment sys­
tem.
The speed warning function will warn you if the
vehicle exceeds the pre-set maximum speed. The
system gives an audible warning signal if the set
speed is exceeded by a small amount. At the
same time, a warning lamp [5] and a message
will appear on the instrument cluster display.
The indicator Lamp [5] and the message will dis­
appear when the road speed drops below the set

value.

You are recommended to store this speed limit
warning if you wish to be reminded of a particu­
lar speed limit. This could be when driving in
countries with general speed limits, or if you
need to keep below a particular speed when
win­

ter tyres are fitted, etc.
Setting speed limit warning

•
Select the following on the infotainment sys­

tem:
IMENUI
button > Car > left control button
> Driver assist > Speed warning > manual.
© Note
- Please bear in mind that, even with the
speed warning function, it is still important
to keep a check on the car's speed with the
speedometer and to observe the statutory
speed limits.
- On vehicles for some markets, the speed
warning function warns you when you reach
a speed of 120 km/h. This speed limit warn­
ing is preset at the factory.
Switching on
Applies to: vehicles with cruise control system
The cruise control system allows you to drive at a
constant speed of 20 km/h or
higher.

Fig.
94 Control lever for cruise control system

• Pull
the lever to position
®
<^>Fig.
94 to switch
on the system.

•
Drive at the speed you wish to set the system

to.

• Press the button marked ® to store the speed.
The indicator lamp
[3]
in the instrument cluster
will light up. Information is also provided in the
head-up display*.
The instrument cluster display will briefly
indi­

cate the stored or
pre-selected
speed.
A constant speed is maintained by adjusting the
engine power or braking the vehicle accordingly.
WARNING
- Always direct your full attention to the
road,

even when you are using the cruise control

system.
It is always the driver who is re­
sponsible for determining the speed and for
keeping a safe distance to the other vehicles
on the
road.

- For safety reasons, the cruise control sys­
tem must not be used in city traffic, stop-
and-go traffic, on roads with a lot of bends
or in difficult or slippery driving conditions
(such as ice, fog, Loose grit or gravel, heavy

rain,
etc.) - risk of accident!
- When you take a turn-off, drive along a mo­
torway exit lane or pass through roadwork
104

Driver assist systems
Automatic deactivation
Cruise control system: currently unavailable.
See owner's manual
The cruise control system has been automatically
deactivated because the system has detected a
fault which could impair its function. Try switch­
ing the cruise control system on again later.
A WARNING
Do not resume the programmed cruising
speed if this is too high
for
the traffic condi­
tions - this can cause accidents.
Speed Limiter
Description
Applies to: vehicles with speed limiter
®
LIM
•

km/h
|

Fig.
95 Speed limiter:
©
LIM
100
km/h
illustration

BFV-0268

LIM
100
km/h
At speeds above approximately 30 km/h, the
speed limiter helps prevent the driver from ex­
ceeding a set cut-off
speed.
The indicator lamp

Q
Lights up as soon as you switch on the speed
limiter. Information is also provided in the head-
up display*.
Speed limiter displays
© - The speed limiter is in passive mode, but a
cut-off speed has
not
yet been set.

®
- The speed limiter is in passive mode, and a
set cut-off speed has been stored.
® - The speed limiter is activated. The indicator
lamp
BH
flashes briefly when the speed limiter is

applied.

A WARNING
- Always direct your full attention to the
road,

even when you are using the speed limiter.
It is always the driver who is responsible for
determining the speed and for keeping a
safe distance to the other vehicles on the

road.

- For safety reasons, the speed limiter must
not be used in adverse weather or difficult
driving conditions (such as ice, fog, loose
grit or gravel, heavy
rain,
etc.) - risk of
acci­

dent!
- Only accelerate quickly or use the kick-down
feature when the visibility and weather
con­

ditions are suitable, and when the road and
traffic conditions allow you do do so safely.
Before driving down a
long,
steep gradient, it
is advisable to reduce speed and select a low­
er gear. In this way you will make use of the
engine braking effect and relieve the Load on
the brakes.
Switching on
Applies to: vehicles with speed limiter

Fig.
96 Control lever for cruise control system (example)

•
Pull the lever to position © to switch the sys­
tem on.

•
Applies to vehicles with cruise control system
or Audi adaptive cruise control: To switch to the
speed limiter, press the button
®1)
until the
driver message
QQ
Speed limiter: selected ap­
pears in the instrument cluster. •

l)
On some equipment versions, the speed limiter is not
available and button
(B)
has no function.
106

Driver assist systems
© Note
The distance may be below the warning
threshold for a short time when overtaking or
approaching a slower vehicle quickly from be­

hind.
In this case, no warning will be given. A
warning is only given if the distance is consis­
tently below the threshold.
Driver messages
Applies to: vehicles with Audi adaptive cruise control

El
ACC:
not available
The system cannot detect vehicles reliably and
will be deactivated. The sensor is out of align­
ment or defective. Drive to a qualified workshop
and have the fault rectified.

EH
ACC:
currently unavailable. No sensor vision

Eo3
ACC:
currently unavailable. Sensor view re­
stricted due to surroundings. See owner's
man­

ual
These messages appear if the radar sensor vision
is impaired, e.g. by leaves, snow, heavy road
spray or dirt. Clean the sensor
^>page
112,
Fig. 101.

E3
ACC:
currently unavailable. Speed too low
Manual gearbox: This message appears if the cur­
rent speed is too low for
ACC
mode. You cannot
store speed settings below 30 km/h. The cruise
control system switches off if the speed falls
be­

low 20 km/h.

Esi
ACC:
available from 2nd gear up
Manual gearbox: The adaptive cruise control only
operates in 2nd gear or higher.

B
ACC:
currently unavailable. Gradient too
steep
The maximum possible road gradient for safe op­
eration of the adaptive cruise control has been

exceeded.
The adaptive cruise control cannot be
switched on.
ffl
Ea3
ACC:
only
available in D, S or M < o

PI
Automatic gearbox: Move the selector lever to

g
position D/S or M. <
00

Eol
ACC:
clutch pedal pressed
Automatic gearbox: Cruise control mode is deac­
tivated if the clutch pedal is pressed for
a
rela­
tively long period.

Bf
ACC:
engine speed
Manual gearbox: This message appears if the
driver does not change gear in time when the
adaptive cruise control accelerates or brakes the
vehicle and the engine speed is too high or low as
a result. The adaptive cruise control is switched

off.

EJACC:
parking brake applied
The adaptive cruise control system is deactivated
if the parking brake is applied. The adaptive
cruise control will be available again when the
parking brake is released.

Eo3
ACC:
currently unavailable. Stabilisation
control input
This message appears if the electronic stabilisa­
tion control (ESC) intervenes. In this case, the
adaptive cruise control will automatically be
switched off.

Eo3 ACC
off: manual control!
This message appears if the vehicLe rolls back­
wards when driving away on a slight gradient,
even though the adaptive cruise control is active.
Press the brake pedal to prevent the vehicle from
rolling back or colliding with an object behind.

EM
ACC:
currently unavailable. Park assist ac­
tive
The systems are switched off when the park as­
sist* is active. The systems will be available again
when the parking manoeuvre is finished.
Distance warning: fault. Please contact work­
shop
The system cannot detect vehicles reliably and
will be deactivated. The radar sensor is out of
alignment or defective. Drive to a qualified work­
shop and have the fault rectified.
Distance warning: currently unavailable. Sensor
view restricted due to surroundings •
119

Driver assist systems

CO

< o rN
r>
rN
t-H
o < 00
-The automatic brake application with in­
creasing brake force can be cancelled by ap­
plying the brakes yourself or by pressing the
accelerator firmly.
- In certain situations, a warning may be giv­
en by the rear cross-traffic assist even if
there is no traffic in the critical zone, for in­
stance when parking or manoeuvring the ve­
hicle in reverse.
- The rear cross-traffic assist is deactivated
automatically if you deactivate the
ESC.

-The rear cross-traffic assist is switched on/
off via the parking aid
^>page
134.
-The system is not available in towing mode.
Driver messages
Applies to: vehicles with Audi side assist
Should the side assist be deactivated automati­
cally, a driver message will appear in the instru­
ment cluster display.

O
Audi side assist: system fault!
The system cannot detect vehicles reliably and
will be deactivated. The sensors are out of align­
ment or defective. Have the system checked by a
qualified workshop soon.

O
Audi side assist: currently unavailable. No
sensor vision

O
Audi side assist: currently unavailable.
Sen­

sor view restricted due to surroundings. See
owner's manual
The radar sensors are blocked. The area in front
of the sensors must not be obstructed by bicycle

racks,
stickers, deposits or any other substances.
If necessary, clean the area in front of the
sen­

sors
^>page
128, Fig. 120.

O
Audi side assist: currently unavailable
The side assist is temporarily inoperative and
cannot be switched on (for instance if the battery
is not sufficiently charged).

O
Audi side assist: unavailable in towing mode

2
Audi side assist: unavailable in towing mode
The side assist function will be switched off auto­
matically after a short time when the electrical
connector for the trailer socket is plugged in on
vehicles with a factory-fitted towing bracket. If
the towing bracket is not factory-fitted the side
assist function may not be switched off automat­
ically. The side assist must not be used when
towing a trailer.

O Rear
parking aid: obstacle detection limited
The rear cross-traffic assist is not available. Ei­
ther the ESC is switched off or the radar sensors
may be obstructed by a bicycle rack, stickers,
leaves, snow or similar objects. Switch on the ESC
or, if necessary, clean the area in front of the
sen­

sors
<3page
128, Fig. 120. If this message re­
mains displayed, drive to a qualified workshop
soon and have the fault rectified.
Audi drive select
Introduction
Applies to: vehicles with Audi drive select
Audi drive select alLows you to use different set­
ups on your vehicle. The modes efficiency*, com­
fort, auto and dynamic allow the driver, for ex­

ample,
to change from a sporty mode to a more
comfortable one via the
&&
button in the centre
console or via the infotainment system. In
addi­

tion,
the individual* mode allows you to adapt
the vehicle set-up to
suit
your personal driving

style.
For example, you might choose to combine
a more dynamic engine set-up with a lighter
steering response.
Description
Applies to: vehicles with Audi drive select
The possible vehicle set-up in each mode de­
pends on which equipment is installed on your
vehicle. The engine and steering are basic parts
of your vehicle which are always included in the

set-up.

Engine and automatic gearbox*
The response of the engine and automatic
gear­

box* to accelerator pedal movements will be
more spontaneous or balanced, depending on
131

Driver assist systems

•
Select the following on the infotainment sys­

tem:
|MENU|
button > Car
>
left control button
> Audi drive select.

•
Select and confirm the desired setting.
You can change the mode while the vehicle is sta­
tionary or moving. If traffic conditions permit,
take
your
foot off the accelerator briefly after you
change the mode so that the new mode is also
activated for the engine.
efficiency* - trims the vehicle to a fuel-saving
set-up and helps the driver adopt an economical
driving style.
comfort - alters the vehicle set-up for a more
comfortable ride and is suitable for long motor­
way trips, for instance.
auto - gives an overall impression of
a
comforta­
ble but dynamic ride and is a good choice of set­
up for everyday use.
dynamic - gives the vehicLe a tighter set-up and is
ideal for performance driving.
individual* -
^>page
133.
A WARNING
Always keep an eye on the traffic when using
the drive select controls - Risk of accident!

CO

rN
r>
rN
•-i

00
Configuring individual mode

You
can configure your own personal vehicle set-up.

*-
Select: |MENU| button > Car
>
Audi drive select
> individual
>
right control button.
The individual* driving mode will automatically
be activated when you have finished configuring
the settings.
Your vehicle's equipment and engine determine
which systems you can select. The following ta­
ble provides an overview of the characteristics.
Systems
Engine/Gearbox
Steering
Audi adaptive cruise control*
Suspension control*
comfort
Comfortable
Comfortable
Comfortable
Comfortable
auto dynamic
Balanced
Balanced
Balanced
Balanced
Dynamic
Dynamic
Dynamic
Dynamic
© Note
Your settings in individual* mode are stored
automatically and assigned to the remote
control key currently in use.
133