page 51 AUDI Q2 2021 Owner´s Manual

Towing a trailer
Tyre pressure
Check the tyre pressures on your car, and adjust
for "full
load"
conditions (refer to the sticker list­
ing the tyre pressures)
^>page
307. It may also
be necessary to adjust the tyre pressures on the
trailer according to the recommendations of the
trailer manufacturer.
Exterior mirrors
Check whether you can see enough of the road
behind the trailer with the standard mirrors. If
this is not the case you should have additional
mirrors fitted. Both exterior mirrors should be
mounted on hinged extension brackets. Adjust
the mirrors to give sufficient vision to the rear.
Headlights
Before starting
a
journey, check the headlight
beam settings with the trailer hitched up. Adjust
the headlight settings if necessary.
On vehicles with halogen headlights, the
head­

light range control must be adjusted, see

tapage
49.
The headlight range control will be adjusted au­
tomatically if your vehicle is equipped with LED
headlights*.
Power supply
To ensure that the engine can be started again
after the ignition is switched off, the power
man­

agement system
^>page
149 controls the distri­
bution of electrical power and gradually switches
off unnecessary electrical equipment. The trailer
is supplied with power during this period. The
power supply to the trailer is interrupted while
the engine is being started.
Removable ball joint coupling
Vehicles with a factory-fitted towing bracket are
equipped with a removable
ball
joint coupling.
This is stored in the spare wheel well or in a sepa­
rate bag on the floor of the luggage compart­
ment, together with the necessary fitting instruc­

tions.

We recommend having the car serviced be­
tween the normal inspection intervals if it
used frequently for towing a trailer.
Trailer stabilisation system
Applies to: vehicles with towing bracket
Trailer stabilisation helps to reduce the risk of
the vehicle skidding when towing a
trailer.

When is the trailer stabilisation
system1'

activated?
Trailer stabilisation is active when the following
requirements are met:
- The ESC must be switched on
^>page
146 and
fully functional (no ESC malfunction).
- The trailer connector must be properly secured
in the vehicle socket.
- The vehicle speed must be higher than approx.
60 km/h.
How trailer stabilisation works
In many cases, the driver can stabilise a swaying
trailer by manually braking the vehicle.
However, if the ESC detects that the trailer is
swaying and this is affecting the towing vehicle,
it will automatically brake the vehicle in order to
stabilise the trailer. The indicator
Lamp Hi
will
flash in the instrument cluster. If possible, do
not turn the steering wheel at this stage.
In order to warn traffic behind you, the brake
lights will come on during this automatic braking

operation.

A trailer may sway quite considerably without the
trailer stabilisation system intervening.
If the system for activating the trailer brake
lights is defective, this will be indicated in the in­
strument cluster display
opage
35,
:&
Bulb

monitor.
•

CO

rN
rN
t-H
o <
x)
Not available on vehicles for some markets.
97

Towing a trailer
Requirements for correct functioning of the
trailer stabilisation system
If these conditions are not met in
full,
the trailer
stabilisation system will only intervene to a
limi­

ted extent or not at all
>=>
A-
- The electrical connection between the towing
vehicle and the trailer must be functioning cor­
rectly.
- The load on the trailer must be properly se­

cured.

- The tyre pressures on both the vehicLe and the
trailer must be adapted to the load that is be­
ing carried.
- Where possible, operate the trailer with the
maximum permitted draw bar weight.
- The trailer overrun brake must be set correctly.
This is important to ensure that the trailer can
be braked correctly, to avoid the vehicle and
trailer "jack-knifing" and to prevent excess
braking of the trailer.
- At low outside temperatures, both the towing
vehicle and the trailer should be fitted with
winter tyres.
A WARNING
It is essential that you adjust your speed to
suit the weather, road and traffic conditions.
Do not let the trailer stabilisation system
tempt you into taking any risks when driving -
this can cause accidents.
- The ESC and trailer stabilisation system
can­

not defy the Laws of physics. This should be
kept in mind, particularly on slippery and
wet roads and when towing a trailer with a
light Load.
- The trailer stabilisation system is function­

al,
regardless of whether the trailer has a
mechanical overrun brake or not.
- The trailer stabilisation system is not always
able to detect swaying of trailers with a
light load and will therefore not intervene.
- A trailer can still "jack-knife" on slippery
roads with little grip, even if the towing ve­
hicle is equipped with the trailer stabilisa­
tion system.
-Trailers with a high centre of gravity may
even tip over before they start to sway
side­

ways.

-If
you
are not towing a trailer,
but
the
trail­

er socket is being used (e.g. for an illumina­
ted bicycle rack), the trailer stabilisation
system may be activated in extreme driving
conditions.
- Please note the additional information and
warnings
^>page
98, Driving tips.
Driving tips
Driving with a trailer always requires extra care.
Weight distribution
Try to avoid towing a loaded trailer with an unla­
den vehicle. If this cannot be avoided, drive extra
slowly to allow for the unbalanced weight distri­

bution.

Speed
Normally, you must not exceed 80 km/h when
towing a trailer or caravan. However, if the
trail­

er/caravan is equipped with a trailer stabilisation

system,
you can drive at max. 100 km/h. Please
observe any other regulations applicable in the
country in which you are travelling.
The stability of the car and trailer is reduced with
increasing speed. For this reason it is advisable
not to drive at the maximum permissible top
speed in unfavourable
road,
weather or wind
con­

ditions. This applies especially on a downhill gra­
dient.
You should always reduce speed immediately if
the trailer shows the slightest sign of swaying.
Never try to stop the swaying by accelerating fur­
ther.
Always brake in good time. If the trailer has an
overrun brake, apply the brakes gently at first
and then firmly. This will prevent the jerking that
can be caused by the trailer wheels locking.
Change down in good time before going down a
steep hill so
that
you can use the engine braking
effect to slow down the vehicLe.
Swaying and pitching can be reduced by attach­
ing an extra stabiliser to the trailer. It should •
98

Towing
a
trailer

CO

< o rN
iv
rN
t-H
o < 00
have friction linings at the sides to prevent exces­
sive wear. Degrease and clean the ball joint be­
fore using a stabiLiser. The stabiliser can be pur­
chased and installed
at
a qualified workshop.
Electronic stabilisation control
The
ESC
-
in particular in conjunction with the
trailer stabilisation system
o^page
97 - makes
it

easier to stabilise a trailer
if it
starts to skid
or

sway. You should therefore keep the
ESC
switch­
ed on
at
all times.
Overheating
In hot weather, keep an eye on the coolant
tem­

perature gauge
^page
13. When climbing long
hills with the engine running fast in low gear, the
coolant temperature can increase. Reduce speed
immediately
if
the needle moves to the right end
of the scale. For information on the warning
lamp
||
refer to
opage
30.

Rear carrier systems
When using rear carrier systems (e.g. bicycle
racks) on the towing bracket,
it
is important not
to exceed the maximum load.
The total weight
of
the rear carrier system and
its

load must not exceed
75
kg for this vehicle. How­
ever,
it
is also important to observe the maxi­
mum permissible load for the rear carrier sys­

tem.

The greater the distance from the towing brack­
et, the smaller the maximum permissible Load
on

the rear carrier system. For this reason, you
should secure heavy objects as near as possible
to the towing bracket.
Note the instructions provided by the manufac­
turer of the rear carrier system.
Please make sure that the rear carrier system
is

approved for use on your vehicle.

l
Note
A WARNING
The use of an unsuitable rear carrier system
could cause severe damage
to
the towing
bracket. The towing bracket could then break
and cause an accident.
Degrease and clean the ball joint before using
a rear carrier system.

Removable towing
bracket

Introduction
Applies to: vehicles with removable towing bracket
Special care is required when fitting and remov­
ing the towing bracket.

Fig.
84 Luggage compartment:
Ball
joint for towing brack­
et (stowage example)
The removable ball joint attachment for the tow­
ing bracket is stored under the floor panel or in a
separate bag on the floor of the luggage com­
partment.
The ball joint can be fitted and removed by hand.
WARNING
Never use tools of any kind when fitting and
removing the ball joint. This could damage
the mechanism which locks the
ball
joint
in

place and impair its safety
-
risk of accident!
© Note
- Do not attempt to modify or repair the ball
joint or other towing bracket components.
- Should you have any difficulties when using
the towing bracket, or suspect that
it
is not
fitted properly, contact
a
qualified work­

shop.

- Before setting off, always check that the

ball
joint is secured properly
Opage
101.
99

Towing a trailer
- Never disengage the ball joint with the cara­
van / trailer still hitched or with a bicycle
rack or similar accessory still attached.
- It is advisable to remove the ball joint when
you are not towing a trailer. Check whether
the plug is properly inserted in the mount­
ing fixture and that the bumper cover is fit­

ted.

-The
ball
joint must be removed if
you
intend
to clean the car with a steam cleaning at­
tachment. Check whether the plug is prop­
erly inserted in the mounting fixture and
that the bumper cover is fitted.
- For installation and removal of the ball joint
we recommend using the gloves provided

for
this purpose.
Fitting the ball joint (step 1)
Applies to: vehicles with removable towing bracket

Fig.
85 Area below rear bumper: Pulling out plug

Fig.
86 Removable towing bracket:
Ball
joint
Mounting fixture
The mounting fixture for the ball joint is located
on the underside of the bumper
^>Fig.
85.

•
Remove the plug
^>Fig.
85 from the mounting

fixture.

•
Check that the mounting fixture is free of dirt;
clean if necessary
•=> /\.

The spring mechanism inside the ball joint
must be in the "ready" position.

•
Check
that
the red marking (5)
^>Fig.
86 on the
knob is inside the green zone on the
ball
joint.

•
Check that the locking ball
(Î)
is inside the hole
in the shaft section of the
ball
joint.

•
Check that the knob protrudes visibly from the
ball joint, so that there is a clear gap (?) be­
tween the knob and the
ball
joint.
The
ball
joint can only be installed if the internal
spring mechanism is in the ready position.
Continued
^>page
100, Fitting the
ball
joint
(step 2).
WARNING
It is important to keep the mounting fixture

clean.
Otherwise the ball joint may fail to en­
gage securely (accident risk).
Fitting the ball joint (step 2)
Applies to: vehicles with removable towing bracket

Fig.
87 Removable towing bracket: Setting the spring
mechanism to the "ready" position

Fig.
88 Removable towing bracket: Inserting the
ball
joint •
100

Towing a trailer
Setting the spring mechanism to the "ready"
position (if required)

•
Insert the key®
^>Fig.
87 for locking the ball
joint into the lock on the knob and turn it
clock­

wise.

•
Pull out the knob in direction ®, hold and turn
in direction ® until the locking ball (5) engages
Inserting the ball joint

•
With the spring mechanism in the "ready"
posi­

tion,
insert the ball joint into the mounting fix­
ture and push it upwards
<=$Fig.
88 in the direc­
tion indicated (arrow)
•=> ^.
The spring mecha­
nism should then engage automatically with an
audible click.

•
Lock the ball joint by turning the key
anti-clock­

wise.

•
Take out the key and press the cover cap onto
the lock.
Continued
^>page
101, Fitting the
ball
joint
(step 3).
Fitting the ball joint (step 3)
Applies to: vehicles with removable towing bracket
A WARNING
- If it is not possible to set the spring mecha­
nism to the "ready" position as described

above,
please contact
a
qualified workshop

and,
for safety reasons, do not use the ball
joint.
- To avoid injury, keep your hands away from
the knob when inserting the ball joint in the
mounting fixture.
Make sure that the knob can turn freely when
the
ball
joint is inserted.

Fig.
89 Removable towing bracket: Safety check

M \

AH^H

eg
n
•>*
0

CO

J
m

Fig.
90 Area below rear bumper: Connecting socket®,
eye for safety cable (5)

•
Check
that
the green marking ®
^>Fig.
89 on
the knob is inside the green zone on the ball
joint.

•
Check that the knob is directly against the ball
joint, so that there is no gap (7) between the
knob and the
ball
joint.

•
Check that the ball joint is locked and the key is
removed (so that the knob cannot be pulled

out).

•
Check that the ball joint fits tightly in the
mounting fixture (try moving it about to check).
• To plug in the electrical connection for the
trail­

er, swivel the connecting socket down from un­
derneath the bumper®
^>Fig.
90.

*•
When you hitch a trailer up to your vehicle,
hook the safety cable into the eye on the tow­
ing bracket®
^F/g.
90.

CO

rN
rN
1-1

00
A WARNING
To avoid accidents, the towing bracket must
not be used if any one of the requirements
lis­

ted above is not met. If this is the case, the
101

Towing a trailer
ball joint must be fitted again properly

^>page
100. Please contact a qualified work­
shop in the event of
a
technical fault.

(T) Note
•
The eye ® on the towing bracket is intended
only for securing the safety cable of the
trail­

er.
Removing the ball joint
Applies to: vehicles with removable towing bracket

*—d

^•^Pfip-®
—
t*\®

Fig.
91 Removable towing bracket: Removing the ball
joint

IT)
CD

CO
m

Fig.
92 Area below rear bumper: Fitting the plug

•
Take off the cover cap and insert the key ®

^Fig.
91 in the lock on the knob.

•
Unlock the ball joint by turning the key
clock­

wise.

•
Take hold of the ball joint and pull out the knob
in direction®.

•
Keep hold of the knob and turn it as far as it
will go in direction ®.

•
Release the knob. The spring mechanism will
remain in the "ready" position
<=> /\.
•
Pull the ball joint down out of the mounting fix­

ture.

•
Insert the plug into the mounting fixture

^>Fig.
92.

•
Swivel the electrical socket upwards as far as
the stop.

•
Stow the ball joint underneath the floor panel
or in the bag on the floor of the Luggage com­
partment, depending on your vehicle configura­

tion.

- Make sure that the plug is properly fitted in
the mounting fixture for the towing bracket.
Otherwise the ball joint may fail to engage
securely the next time it is attached if dirt
has accumulated in the mounting fixture.
- On vehicles in which the
ball
joint is stowed
in a bag on the floor of the luggage com­
partment, the bag must always be secured
to the front right fastening
ring.
Otherwise
the bag could be catapulted through the in­
terior of the vehicle in the event of sudden
braking or an accident - risk of injury and ac­
cident!
Retrofitting
Please contact a qualified workshop to find out
whether your vehicle can be retrofitted with a
towing bracket.

I

B38.2

556,1
301,1

Fig.
93 Installation dimensions and positions of securing
points •
102

Driver assist systems

CO

< o rN
iv
rN
•-i

00
sections, please temporarily switch off the
cruise control system.
- Make sure you do not unintentionally rest
your foot on the accelerator - this will over­
ride the cruise control system which, as a re­
sult, will not brake the vehicLe.
-The automatic braking function may be de­
activated if
a
system fault occurs in the
brake system (e.g. if the brakes overheat)
while the cruise control system is activated.
All the other cruise control functions remain
activated as long as the indicator lamp
^
is
lit.
Before driving down a
long,
steep gradient, it
is advisable to reduce speed and select a low­
er gear. In this way you will make use of the
engine braking effect and relieve the Load on
the brakes.
© Note
- Applies to vehicles with manual gearbox:
The set speed cannot be reached if the cur­
rently selected gear is too high or too low or
if the engine would
overrevorfailto
run
smoothly at the target speed. Make sure to
change up or down a gear in good time.
- The brake lights come on when the system
brakes the vehicle.
Setting a new speed
Applies to: vehicles with cruise control system
• Briefly push the Lever towards
©/®

^>page
104, Fig. 94 to increase or reduce the
cruising speed in small steps.

•
To increase or reduce the speed quickly, hold
the lever towards
©/®
until you reach the de­
sired cruising speed.
Overriding the set speed
Applies to: vehicles with cruise control system
You can use the accelerator pedal to increase
speed in the normal way, for example to overtake
another vehicle. Once you release the accelera­
tor, the system will revert to the speed you stor­
ed initially.
However, if the vehicLe exceeds the programmed
speed significantly for
a
long time, the cruise
control system will be deactivated temporarily.
The indicator lamp
El
in the instrument cluster
will go out, but the programmed speed will re­
main stored.

Pre-selecting
a speed
Applies to: vehicles with cruise control system

You
can preselect a desired speed while the ve­
hicle is stationary.

•
Switch on the ignition.

•
Pull the lever to position
® ^>page
104,
Fig. 94.
• Press the lever up towards © or down towards

0
in order to increase or reduce the cruising
speed setting.
This function allows you to enter the desired
cruise control setting speed ahead of
time,
for
example before joining a motorway.
Once
you are
on the motorway, you can activate the cruise
con­

trol system by pulling the lever to position ®.
Switching off
Applies to: vehicles with cruise control system
Switching off temporarily

•
Press the brake pedal, or

•
Push the lever to position @ (click stop not en­
gaged)
^>page
104, Fig. 94, or
Switching off completely

*•
Push the lever to position
©
(click stop engag­

ed),
or

•
Switch off the ignition.
The speed setting will remain stored after the
system is temporarily deactivated. To resume the
programmed cruising speed, release the brake
pedal and pull the lever to position ®.
The stored speed will be deleted once the
igni­

tion is switched off. •
105

Driver assist systems

CO

<
O
rN
iv
rN
t-H
o < 00

•
Press button ® to store the cut-off speed while
the car is moving.
The instrument cluster display will indicate the
stored cut-off
speed,
and the indicator lamp
Q

will light up.
Applies to: vehicles with cruise control system or Audi adap­
tive cruise control
While the speed Limiter is switched on, you can
switch to the cruise control
^>page
104 or adap­
tive cruise control
^>page 111
systems. Press
button
®1)
until the corresponding system is
displayed in the instrument cluster.
The last cut-off speed set for the speed limiter
remains stored and can be applied again when
you switch back into speed limiter mode.
Changing the cut-off speed
Applies to: vehicles with speed limiter

•
Briefly push the Lever towards ©/©

^>page
106, Fig. 96 to increase or reduce the
cut-off speed in small steps.

•
To increase or reduce the cut-off speed in
big­

ger steps, hold the lever towards ©/© until
you reach the desired cruising speed.
Overriding the cut-off speed
Applies to: vehicles with speed limiter
To override the speed limiter temporarily, press
the accelerator fully past the point of resistance
(kick-down feature).
Speed limiting is suspended temporarily. The in­
dicator lamp
QB
flashes while the system is deac­

tivated;
the cut-off speed setting will remain

stored.
The system is reactivated automatically
as soon as your speed drops below the original
stored setting.
Switching off
Applies to: vehicles with speed limiter
Switching off temporarily

•
Push the lever towards © (click stop not en­
gaged)
^>page
106, Fig. 96. The instrument
cluster display will indicate the stored cut-off

speed,
and the indicator
lamp^will
light up.
Switching off completely

•
Push the lever to position © (click stop engag­

ed),
or

•
Switch off the ignition.
The cut-off speed setting will remain stored after
the system is temporarily deactivated. To resume
the programmed cut-off
speed,
pull
the lever to
position ©. The vehicle speed is limited to the
stored cut-off setting as soon as your current
driving speed drops below the stored cut-off

speed.

The stored cut-off speed will be deleted once the
ignition is switched off.
Automatic deactivation

QQ
Speed limiter: currently unavailable. See
owner's manual
The speed Limiter has been automatically deacti­
vated because the system has detected a fault
which could impair its function. Try switching on
the speed limiter again Later.
A WARNING
The speed limiter may be deactivated if a
fault occurs in the brake system (e.g. if the
brakes overheat) while the speed limiter is ac­

tivated.

©
Not

If
a
system fault requires the speed limiter to
switch off automatically, for safety reasons it
does not switch off completely until the driver
releases the accelerator pedal once or deacti­
vates the system manually.

l)
On some equipment versions, the speed limiter is not
available and button
(S)
has no function.
107

Driver assist systems
Camera-based traffic
sign recognition
Description
Applies to: vehicles with camera-based traffic sign recogni­
tion

Fig.
97 Instrument cluster: Traffic sign recognition

Fig.
98 Windscreen: Camera window for traffic sign recog­
nition
Traffic signs detected by the system appear in
the instrument cluster display to keep you in­
formed of current speed restrictions and no-over­
taking zones
^>Fig.
97. Within certain system

limits,
it will display these additional traffic re­
strictions:

£5
///

s

G

^-if?

Speed limits in wet weather
Speed limits in foggy conditions (only dis­
played when the all-weather lights or rear
fog light are switched on)
Speed limits at certain times of day
Speed limits when towing a trailer
General notes
The traffic sign recognition system can detect
standardised speed Limit signs within the cam­
era's range of
vision.
It makes use of the naviga­
tion data to evaluate the detected speed limits
and show them on the display. Under certain
con­

ditions, the system will also display the legal
speed limits on roads without speed Limit signs.
The traffic sign for the currently detected speed
limit will flash on the display if
a
speed warning

threshold,
which has been set on the infotain­
ment system, is exceeded
^page
109.
Traffic sign recognition is not available in all
countries. For
a
current list, see the Internet (e.g.
www.audi.com). The system is also subject to
certain inherent restrictions and may be partially
or completely unavailable in the following situa­

tions:

- If visibility is impaired by snow,
rain,
fog or
heavy road spray.
- In dazzling light, e.g. from the sun or oncom­
ing traffic.
-At high speeds.
- If the camera's range of vision
^>Fig.
98 is im­

paired,
e.g. by dirt or stickers. Notes on clean­
ing
•=>
page 312.
- If the traffic signs are partially or completely

obscured,
e.g. by trees, snow, mud or other
vehicles.
- If traffic signs deviate from the standard ap­
pearance (round with red border).
- If traffic signs are damaged or bent.
- If matrix traffic signs are mounted on overhead
gantries.
- If traffic signs or routes have changed (naviga­
tion data out of date).
- If the system detects a speed sticker on a slow-
moving vehicle (such as a heavy goods vehicle).
WARNING
Always direct your full attention to the road
and surroundings, even when you are using
traffic sign recognition. The actual traffic
signs on your route always take precedence

over
the information on the display. It is al­
ways the driver's responsibility to assess the
traffic situation and take appropriate care.
- Under adverse conditions, the traffic sign
recognition system may misinterpret or fail
to detect traffic signs. It is therefore possi­
ble that the speed limit display may occa­
sionally be unavailable or even incorrect.
108

Driver assist systems
key in use. If you change to a different type
of trailer, you may need to change the maxi­
mum trailer speed setting.
- Information is also provided in the head-up
display*.
- Please note
that
the navigation system (SD

card)*
is immediately no longer available if
the SD card is removed from the SD card
reader.
Driver messages
Applies to: vehicles with camera-based traffic sign
recogni

tion

EJ
Traffic sign recognition: currently unavaila­

ble.
No camera view
This message will appear if the camera view is
obstructed
^>page
108. The system will switch
it­

self off.

EJ
Traffic sign recognition: currently restricted
This message appears, for instance, in the event
of a navigation system fault. The Limited func­
tionality may cause fewer speed limits to be dis­
played (which increases the possibility of an er­

ror).

Traffic sign based speed warning: currently
unavailable. See owner's manual
No warning will be given if the selected warning
threshold is exceeded.
Traffic sign recognition: system fault
The function of the system is impaired; the sys­
tem will be deactivated. Drive to a qualified
workshop soon.
No traffic sign recognised
No relevant navigation data are available, and no
speed limit has been detected.
Traffic sign recognition: outside operational
area
Function unavailable in this country
The vehicLe is being driven in a country outside
the system's operational area.
Rest recommendation
General notes
Applies to: vehicles with rest recommendation
Under certain conditions, the system can detect
that the driver needs to take a break.
At the beginning of a trip, the system monitors
the driver's general steering style. Using this as a
reference, the system continuously compares the
current steering input at speeds of between 60
km/h and 200 km/h. If the evaluation of the
steering input implies a lapse in the driver's
con­

centration,
the system will then recommend a
break
^>page
111,
Instrument cluster display.
The rest recommendation function is designed
for journeys on motorways and major roads.
System limitations
The rest recommendation function may misinter­
pret the steering input in certain driving situa­

tions,
such as the following:
- On twisty roads.
- On rough roads.
- In poor weather.
- During performance driving.
- When the driver's attention is distracted.
Resetting the system
The system is automatically reset if
you...

- switch off the ignition.
- release the driver's seat belt and open the driv­
er's door.
- drive slower than 60 km/h for a while. If you
subsequently increase your speed again, the
system will reevaluate the driving style.

/\
WARNING
- Never drive when you are
tired.
As a driver
you are always responsible for ensuring that
you
are
fit to drive.
- On
Long
journeys, make sure to take
quate breaks at regular intervals.

ade-

- The system cannot always tell if
you
need a
break.
110