tow AUDI Q3 2018 Owner's Guide

-Do not bend over the batteries -danger of
chemical burns!
- The battery cell locking screws must be
tightened securely.
- Before you check anything in the engine
compartment, a lways read and heed all
WARNINGS
¢ page 155.
(D Note
Improper hook-up of jumper cables can ruin
the generator.
- Always connect POSITIVE(+) to POSITIVE
( + ), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager contro l
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly . If not, tighten
plugs prior to connecting clamp on negative
battery terminal.
- Please note that the procedure for connect­
ing a jumper cable as described above ap­
plies specif ically to the case of your vehicle
being jump started. When you are giv ing a
jump start to another vehicle, do
not con­
nect the negative( -) cab le to the negative
(-) terminal on the discharged battery@
¢ fig. 161. Instead, securely connect the
negative (-) cable to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outs ide, escaping battery gas
could ignite and explode!
Towing with a tow truck
General hints
Your Audi requires special handling for towing .
The following information is to be used by com ­
mercial tow tr uck operators who know how to op­
erate their equipment safely .
-Never tow your Audi, towing will cause dam-
age to the engine and transmission .
a '.:: -Never wrap the safety chains or winch cables
~ around the brake lines. N
"" 0 0 ::, (X)
Emergency situations
-To prevent unnecessary damage , your Audi
must be transported with a flat bed truck.
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at·
tach to the front or rear anchorage
¢ page 205 and ¢ page 206.
A WARNING ~ -
A veh icle being towed is not safe for passen­
gers . Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Only install the front towing loop when it is
needed.
®
®
0 0:, N 9 ::> 0:, a)
Fig. 162 Front bumpe r on t he r ight s ide: remove t he cover
Fig. 163 Front bumpe r on t he right side: screw in the tow-
in g loop ...
205

Emergency situations
The threaded opening for the towing loop is lo­
cated behind a cover on the right side of the front
bumper. Depending on the version, the cover can
be removed in different ways¢
fig. 162 .
... Version @: remove the towing loop and the
hook from the vehicle tool kit
r=> page 191. Or
... Version @: remove the towing loop from the
vehicle tool kit
r=> page 191 .
... Version @: insert the hook into the hole on the
cover and carefully pull off the cover in the di ­
rection of the arrow¢
fig. 162 . Or
.,. Version @: press the cap inward with brief,
fo rceful pressure
r=;, fig. 162. Th e cap w ill loosen
from the bumper.
... Tighten the towing loop in the threaded open­
ing until it stops
r=;, fig. 163 and then tighten it
with a wheel wrench.
... After using, place the towing loop back in the
vehicle tool kit.
A WARNING
If the towing loop is not tightened until it
stops when insta lling, the threads may be
pulled out when tow ing the veh icle and that
cou ld cause an accident.
Rear towing loop
Fig. 164 Rear bumpe r: cover
206
-
Fig. 165 Rear bumper : install ing the tow ing loop
Vehicles with a towing loop
On vehicles without a factory -installed trailer
hitch*, the rear towing loop is located on the
right side of the bumper .
... Remove the towing loop from the vehicle tool
kit
r=;, page 191 .
.,. Press the cap inward with brief , forceful p res­
sure
r=> fig. 164 . The cap will loosen from the
bumper.
8l N 9 ::, co m
... Tight en the towing loop in the threaded open­
ing until it stops
r::!;> fig. 165 and then tighten it
with a wheel wrench.
... After using, place the towing loop back in the
vehicle tool kit .
Vehicles with a trailer hitch*
... Til t the trailer hitch out .
... Attach the towing bar or the towing cable to
the trailer hitch .
A WARNING
If the towing loop is not tightened until it
stops when installing, the threads may be pulled out when towing the vehicle a nd that
could cause an accident .
A WARNING
Applies to: vehicles with trailer hitch
-
- Only use a spec ial towing bar to prevent
damagi ng the ball hitch. These towing bars
have been specially designed for trailer tow­
ing hitches.
- Only use special towing cab les.

a
co
...... N r--. N .... 0 0 ::, co
Loading the vehicle onto a flat bed truck
Fig. 166 Vehicl e on fla t bed tr uck
Front hook up
• Align the vehicle with the centerline of the car
carrier ramp .
• Attach the winch hook to the front towline eye
prev iously installed .
Rear hook up
• Align the vehicle with the centerline of the car
carrier ramp .
• Attach the winch hook to the rear towline eye
previously installed.
@ Tips
Check carefully to make sure the hook-up is
secure before moving the car up the flatbed
truck ramp.
Raising the vehicle
Lifting with workshop hoist and with floor
jack
The vehicle may only be lifted at the lifting
points illustrated.
Fig. 167 Fro nt lifting poi nt
Emergency situations
Fig. 168 Rear lifting po int
• Read and heed WARNING c:> .&_.
• Locate lifting points c:> fig. 167 and c:> fig. 168 .
• Adjust l ift ing arms of workshop hoist or floor
jack to match vehicle lifting points.
• Insert a rubber pad between the floor jack/
workshop hoist and the lifting points.
If you must lift your vehicle with a floor jack to
work underneath, be sure the vehicle is safely
supported on stands intended for this purpose.
Front lifting point
The lifting point is located on the floor pan rein­
forcement about at the same level as the jack
mounting point
c:> fig. 167. Do not lift the vehi­
cle at the vertical sill reinforcement .
Rear lifting point
The lifting point is located on the vertical rein­
forcement of the lower sill for the on board jack
c:>fig . 168.
Lifting with vehicle jack
Refer to c:> page 194 .
A WARNING
-To reduce the r isk of se rious injury and vehi­
cle damage.
- Always lift the vehicle only at the special
workshop hoist and floor jack lift points i l­
lustrated
c:> fig. 167 and c:> fig. 168.
- Failure to lift the vehicle at these points
could cause the vehicle to tilt or fall from
a lift if there is a change in vehicle weight
207

Consumer Information
Consumer Information
Warranty coverages
Your Audi is covered by the following warran­
ties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulati ons in the United States and
Canada require that automobi les meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana ­
da differ from vehicles sold in other countries.
If you plan to take your vehicle outside the conti­
nenta l limits of the United States or Canada,
there is the poss ibility that:
- un leaded fue ls for vehicles with catalytic con­
verter may not be available;
- fuel may have a considerably lower octane rat­
ing . Improper fuel may cause engine damage;
- service may be inadequate due to lack of proper
service facilities, tools or testing equipment;
- r eplacement parts may not be readily available.
- Nav igation systems for veh icles built for the
U.S .A . and Canada will not necessarily work in
Europe, and may not work in other countries
outside of North America.
212
(D Note
Audi cannot be responsib le for mechanical
damage that could result from inadequate
f u el, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and Litera ­
ture are published as soon as poss ible after mod­
el introd uction . Service Manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at :
www.audi.techliterature .com
Maintenance
General '
Your vehicle has been designed to help keep
maintenance requirements to a min imum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your vehicle's safety,
economy and reliability . For detailed vehicle
maintena nce consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam ­
ple at extremely low outside temperatures, in
very dusty regions, whe n towing a trailer very fre­
quently, etc., some service work should be per­
formed between the intervals specified. This ap­
plies particularly to:
- oil changes, and
- cleaning or replac ing the a ir filter .
'
@) For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that em iss ion standards are
maintained, thus minimizing adverse effects
on the environment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the genera lly increas ing technica l complexity of ..,_

Index
Sunroof
refer to Panorama glass roof . . . . . . . . . . . 31
Sunshade
Emergency closing (panorama glass roof) .
32
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 7
Symbols
refer to Indicator lights . . . . . . . . . . . . . . . . 10
T
Tachometer. . . . . . . . . . . . . . . . . . . . . . . . . . 8, 9
Technical data . . . . . . . . . . . . . . . . . . . . . . . . 209
Technical modifications . . . . . . . . . . . . . . . . 215
Temp erature display
Outside temper ature . . . . . . . . . . . . . . . . . . . 9
Temperature indicator Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
Temporary spare tire . . . . . . . . . . . . . . . . . . 197
Tether anchors . . . . . . . . . . . . . . . . . . . . . . . 149
Tether strap . . . . . . . . . . . . . . . . . . . . . . . . . 149
Tie-down rings . . . . . . . . . . . . . . . . . . . . . . . 103
Tie -downs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Time . .... .. .. .. ............. .... .. ... 9
tiptronic mode (automat ic transmission) . . . 70
tiptronic (automatic transmission) . . . . . . . . 66
Tires................................ 166
All
wheel drive . . . . . . . . . . . . . . . . . . . . . . . 93
Low-profile tires . . . . . . . . . . . . . . . . . . . . . 182
Replacing . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Service life . . . . . . . . . . . . . . . . . . . . . . . . . 17 5
Tire pressure . . . . . . . . . . . . . . . . . . . . . . . 176
Tir e pressure monitoring system . . . . . . . 183
Tire pressure table . . . . . . . . . . . . . . . . . . . 177
Tire pressure (trailer towing) . . . . . . . . . . . 73
Treadwear indicators . . . . . . . . . . . . . . . . .
175
Unidirectional . . . . . . . . . . . . . . . . . . . . . . . 168
Uniform tire quality grading . . . . . . . . . . . 182
Tires and wheels
Glossary of tire and loading terminology .
169
Tires and vehicle load limits . . . . . . . . . . . 17 8
Tool . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 1
Torn or frayed safety belts . . . . . . . . . . . . . . 108
Towing
Tow trucks . . . . . . . . . . . . . . . . . . . . . . . . .
205
Towing loop . . . . . . . . . . . . . . . . . . . . . 205, 206
TPMS (Tire Press ure Monitoring System) . . 183
224
Trailer towing . . . . . . . . . . . . . . . . . . . . . . . . . 73
Parking systems . . . . . . . . . . . . . . . . . . . . . .
88
Trailer load . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . .
16
Transport Canada . . . . . . . . . . . . . . . . . . . . . 104
Turn signal . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
u
Unfastening safety belts
Uniform tire quality grading
Unlocking/ locking 111
182
By remote control . . . . . . . . . . . . . . . . . . . . 24
With the central locking sw itch . . . . . . . . . 25
With the convenience key . . . . . . . . . . . . . . 24
Use of jumper cables . . . . . . . . . . . . . . . . . . 204
V
Vanity mirror.... .. .. .. ............. ... 37
Vehicle Care/cleaning . . . . . . . . . . . . . . . . . . . . . . .
185
D .
. 1mens1ons ...... .. .. .............. .
Out of service .. .. .. .. .. ........... . .
Specifications ..................... . . 210
190
209
Vehicle battery . . . . . . . . . . . . . . . . . . . . . . . 163
Charge leve l . . . . . . . . . . . . . . . . . . . . . . . . . 94
Charging . . . . . . . . . . . . . . . . . . . . . . . . 13, 164
Energy management . . . . . . . . . . . . . . . . . . 94
Vehicle control modules . . . . . . . . . . . . . . . . . 95
Vehicle jack . ... ... .. .. ... ..... ... 191,194
Vehicle key . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Vehicle tool kit . . . . . . . . . . . . . . . . . . . . . . . 191
VIN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
w
Warning lights
refer to Indicator lights . . . . . . . . . . . . . . . . 10
Warranty coverages . . . . . . . . . . . . . . . . . . . 212
Washing matte finish paint . . . . . . . . . . . . . 185
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 209
What happens if you wear your safety belt too
loose? . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
110
What happens to unbelted occupants? . . . . 107
What impairs driving safety? . . . . . . . . . . . . . 97
Wheel bolt caps
Removing . . . . . . . . . . . . . . . . . . . . . . . . . .
193