display AUDI Q5 2013 User Guide

Trip computer
Introduction
The trip computer gives you information on
current and average fuel mileage, average
speed, fuel rang e and driving tim e.
Fi g. 15 Trip computer display: Average fuel mileage
The fo llow ing informa tion is cont in uously
eva luate d by the trip compu ter and can be dis ­
p layed sequent ia lly in the instrument cl uster
d isp lay:
Fuel range
The estim ated cruising r ange in miles (k m)
appears in the display . This te lls you how far
your veh icle w ill be able to t ravel on the cur ­
rent tank of fue l and with the same dr iving
style. The display changes in increments of 6
m iles (10 km).
Average fuel mileage
The ave rage fue l economy in MPG (l/ 100 km)
since you last clea red the memory appears i n
this display. Yo u can use th is disp lay to adjust
your driving technique to achieve a desired
mileage.
Current fuel mileage
The instantaneo us fue l cons umption in miles
pe r gallo n (l/ 100 km) is shown in this d isp lay .
You can use this display to adj ust your dr iving
techniq ue to ach ieve a des ired mileage.
Fu el consumption is reca lcula ted at interva ls
of 33 yards (30 mete rs) . This display switches
to ga llons/ho ur (lite rs/hou r) when the vehicle
is not mov ing.
Driver information display 23
Average speed
T he average spee d in mph ( km/ h) since the
l ast time the display was reset appea rs in the
display.
Elapsed time
T he length o f time that yo u have been d rivi ng
s in ce you last re se t the memory appea rs i n
t h is disp lay.
Distance
The distance t hat has been covered since the
l ast t im e the m emory was clea red appea rs in
t he d isplay .
(D Tips
-Fuel consumptions (average and cur­
rent) , range and sp eed are d isp laye d in
m etri c un its on Canadi an mo dels.
- All sto red val ues will b e lost if t he vehi­
cle battery is di sconnected.
Memories
The trip comput er is equipped with two fully
automatic memories as well as an efficiency
p rog ram*.
Fig. 1 6 Trip computer display: memory leve l 1
-"' ... q a:
:l!
You can switch between the trip computer 1
and 2 and the efficiency program * by pressing
the
I RESET I butt on @ c:> page 24, fig. 17.
You can te ll wh ic h memory leve l is currently
active by the numbe r or the sign in the display
¢fig. 16. The data from the s ingle-trip mem­
ory (memory level
1) is being displayed if a D
appears in the display. If a fJ is show n, then
the data from the total-trip memory is being
displayed (memory level 2). T he fue l pump .,..

24 Driver in formation d isplay
nozzle ii indicates the efficiency program*
¢page 25.
Single-t rip memory (Trip computer 1 )
The single-t rip memo ry sto res the trip infor­
mat ion from the time the ignition is turned o n
until it is tu rned off . If the trip is contin ued
w ithin 2 hours from the time the ignition was
turned off, the new data will be included in
the calcu lation of the current trip informa ­
tion. If the trip is interrupted for
more than 2
hour s
the memory is reset automatically.
Total -tr ip m emory (Trip compu ter 2 )
Unlike the sing le-trip memory, the tota l-trip
memory is not reset automatically. This per­
mits you to evaluate your driving data for the
entire period between manual resets.
Effici ency prog ram*
The efficiency p rogram can help yo u to use
l ess fuel ¢
page 25 .
Operation
The trip computer is controlled by two
switches on the windshield wiper lever.
~
--- ®
Fig. 17 Windshie ld wipe r leve r: controls fo r th e trip
co mp ute r
.,. To d isp lay the trip computer memory leve ls ,
press the
I RESE T I button ®¢ fig. 17 re­
peatedly unt il the desired memory leve l is
shown in the d isp lay .
... To disp lay trip information within a memory
level, press the top or bottom part of the
function selection switch
@ .
The trip computer w ill not operate unless the
ignition is on. When you turn on the ignition, the function that was in use when you last
turned the ignition off wi
ll be displayed .
In add ition to info rm ation on the trip comput ­
er (trip computer 1, 2 and eff ic iency p ro­
gram*, the d igital speedometer and informa­
tion regarding the navigation system * can a l­
so be displayed. To switch the d isp lay between
the d ifferent informat ion, tap the
I RESE T I but­
ton ® briefly.
Sett ing values to ze ro
To de lete one current va lue from the trip com ­
puter, se lect the desired functio n and press
the
I RESET I button ® for at least one second.
The following values can be set to zero
indi ­
v iduall y:
-Average fue l mi leage
- Average speed
- Elapsed t ime
- Distance
All currently d isplayed va lues are deleted in
the efficie ncy program*.
In add ition,
all the values in the sing le-trip or
the total-tr ip memory can be de leted sim ulta­
neously ¢
page 24.
(!) Tips
All stored va lues w ill be lost if the veh icle
battery is disconnected.
Basic Settings for the trip computer
The MMI* or the radio operating unit is used
for setting the trip computer's basic settings.
.,. Select: !CAR ! function b utton > In strument
cluster > On-board computer
1 or On-board
computer
2 .
The values in the sing le -tr ip or the total-t rip
memory can all be reset to zero at the same
time under
Reset in the menu .
In add ition, yo u can de termi ne wha t informa­
tion from the t rip computer should be shown
in the instrument cluster disp lay . If one of the
pieces of driver information is turned
Off , that
drive r information will not be shown in the ..,.

display . Th e information will continue to be
calculated by the trip computer and can be
turned back
On at any time.
@ Tips
- This function is not avai lab le on all
vehicles.
- The driving information in the efficiency
program * is a lso reset to zero w ith the
single-trip memory .
Efficiency program
Description
Applies to vehicles: with efficiency program
Fig . 1 8 Disp lay : effi cienc y program
.. Press the !RESET I button ® c:> page 24,
fig. 17 repeatedly un til the efficiency pro­
gram appears in the display .
T he efficiency program can help you to use
less fuel. It eval uates driving info rmation in
re ference to fuel consump tion and shows o th­
er equipment i nfluencing consumption . Fuel
economy messages
c:> page 25 provide tips
for efficient driving .
The eff ic iency program uses distance and con­
sumpt ion data from trip computer
l. If the
data are de leted in the eff iciency program,
thos e val ues are a lso reset in trip computer
1.
Dri ver inform ation di spl ay 25
Other equipment
Applies to vehicles: with efficiency program
Fig. 19 D ispl ay : other equ ipmen t
.. In the efficiency program, press the func­
tion se lection switch
c:> page 24 , fig . 17 @
repeatedly until the other equipment ap­
pea rs in the display .
Other equipment th at is currently affecting
fuel consumpt io n is lis ted i n the effic iency
program . The display shows up to three other
items of equ ipment @. The equ ipment using
the most fuel is listed first .
If more than th ree
items us ing fuel a re switched on, t he equip­
ment t hat is c urrently usin g the most fuel is
displayed .
A scale @ also shows the c urrent tota l con­
sumption of all othe r equipmen t.
Fuel economy messages
Applies to vehicles: with efficiency program
Fig. 20 Disp lay: fuel econo my message
Fuel economy messages are displayed when
fuel consumpt ion is increased by certain con­
di tions .
If you fo llow these fuel economy mes­
sages, you ca n reduce your veh icle's consump­
t ion of fuel. The messages appea r automat i-
ca lly and are only d isplayed in the efficiency ..,.

26 Driver information d isplay
program. The fuel economy messages turn off
automatically after a certain per iod of t ime .
.,. To turn a fuel economy message off imme-
dia tely after it appears, press the
I RESE T I
button Q page 24 , fig . 17 @, or
.,. Press the funct ion selection switch
~ page 24 , fig. 17@.
(D Tips
-Once you have turned a fuel economy
message off, it will only appear again af­
ter you turn the ignition on again.
- The fuel economy messages are not dis­
played in every instance, but rather in in­
tervals over a period of time.
On-Board Diagnostic
system (OBD)
Malfunction Indicator Lamp (MIL)
T he Malfunction Indicator Lamp (MIL) ¢4 in
the instrument cluster
Q page 14, fig. 8 is
part o f the On-Board Diagnostic (OBD II) sys­
tem.
T he warning/indicator light illuminates when
the ignition is switched on and goes out after
the engine starts and the idle has stabilized .
T his indicates that the MIL is working proper ­
ly .
If the light does not go out after the engine
is started, or illuminates while you are driv­
ing, a malfunction may exist in the engine sys ­
tem. If the light illuminates, the catalytic con­
verter could be damaged.
Continue driving
with reduced power (avoid­
ing sustained high speeds and/or rapid accel­
erat ions) and have the condition corrected .
Contact your author ized A udi dealer.
If the light illuminates, the electronic speed limiter may also be malfunctioning. For more
information
Q page 2 7, Electronic speed
limiter .
An improperly closed fuel filler cap may also
cause the MIL light to illuminate
Qpage231 .
On-Board Diagnostics
Fig. 21 Location of Data Li nk Conn ecto r (DLC)
On-Board Diagnostics monitors the compo­
nents of your emission control system . Each
monitored component in your engine system
has been ass igned a code . In case of a mal­
function, the component will be identified
and the fault stored as a code in the control
module memo ry.
The MIL light may also illuminate if there is a
leak in the on-board fuel vapor recovery sys­
tem .
If the light illuminates after a refueling,
stop the vehicle and make sure the fuel filler
cap is properly closed
Q page 231.
In order to make an accurate diagnosis , the
stored data can only be displayed using spe ­
cial diagnostic equipment (generic scan tool
f or OBD).
In order to connect the spec ia l diagnostic
equipment , push the plug into the Data Link
Connector (DLC). Th e DLC is located to the
right of the hood release
Qfig. 21.
Your authorized Audi dea ler or qualified work­
shop can interpret the code and perform the
necessary repair.
~ ARNING
Do not use the diagnostic connector for
personal use. Incorrect usage can cause
malfunctions, which can increase the risk
of a collision!
-

Electronic speed
limiter
Your vehicle may be factory equipped with
tires that are rated for a maximum speed of
130 mph (210 km/h) . This is less than the
maximum speed of your vehicle . To reduce the
risk of sudden tire failure and loss of control if
the vehicle is ope rated at excessive speeds,
your veh icle also has an elect ronic speed limit­
er. The electronic speed limiter prevents your
ve hicle from going faster than the tire speed
rating. For more information
c::> page 259 .
If the engine control unit rece ives fau lty vehi­
cle road speed signals, the Malfunction Ind i­
cator Lamp (MIU¢• will illuminate . If this
occurs, contact the nearest authorized Audi
dea ler for assistance.
A WARNING
Always observe the posted speed limits
and adjust your speed to suit prevailing
road, traff ic and weather conditions. Never
drive your vehicle faster than the maxi­
mum speed ra ting of the tires insta lled.
Auto Check Control
Introduction
The Auto-Check control monitors the function
of certain veh icle features and components. It
simply makes sure these features and compo­
nents are work ing properly . The Auto-Check
control wo rks as long as the ignition is on, as
well as whenever the vehicle is driven .
If a component is malfunctioning or if the need for an urgent repair has been detected,
this wi ll appear in the instrument cluster dis­
p lay. You will a lso hear a n aud ible warn ing
tone. The d isplays are color coded in either
red or yellow depending on their level of prior­
ity.
A red symbo l means
Dang er, a ye llow symbo l
indi cates
W arning . In certain s ituations, in­
formation message for the dr iver appear in
additio n to the red and yellow symbols .
Driver inform ation di spl ay 2 7
Note about autom atic transmi ssion
T he Au to-Che ck Con trol wi ll automa tically
perform a test each t ime you sw itch on the ig­
nition. With the selecto r lever in P or N, the
following message appears in the display:
When stationar y appl y brake pedal while se­
lect ing gear
When you se lect a d iffe ren t gear (for exam­
ple: R, D, etc.), t he mes sage will disappea r
and the Auto-Check f unct ion is displayed .
If there is a malfunct ion, then the malfu nc·
tion message will appear about 15 seconds af­
te r you start the vehicle. At the same time you
will hear a wa rning tone.
Driver information messages
Driver information messages are shown in the
instrument cluster display in addition to sym­
bols .
Fig . 2 2 Instrument cluster: SET b utto n
For example, if the transmission selector lever
is not in the P position when the engine is
turned off, the follow ing message appears :
Shift to P otherwise vehicle can roll away.
Door s do not lock if le ver is not in P .
The ign ition key can only be removed with the
selector in this position. This and other mes­
sages are bro ught up if a function cannot be
carr ied out .
Driver messages and red s ymbols
If a red symbol appears in the display, a driver
message is also displayed au toma tically . ..,..

28 Driver information d isplay
F or example, the symbol for a p roblem with
engine oi l pressure . appears i n the display .
The fo llow ing message appears:
Turn off engine! Oil pre ssure too low
The driver message in the display goes out af­
ter about
5 seconds. The dr iver message ca n
b e d isp layed again by briefly pressi ng the
ISE Tlbut ton
r:::;, fig. 22.
Driver messages and yellow symbols
If a ye llow symbo l appears in the display, a
d river message is a lso displayed automat ica l­
l y.
For example, the symbo,
(-$ appea rs in the
d isplay, ind icati ng low w indshield was her flu­
id leve l. The follow ing message also appears:
Please refill washer fluid
The driver message disappears after a few
seconds . The driver message can be d isp layed
again by b rief ly pressing the !SET I button.
Red symbols
A red symbol means DANGER .
Fig . 2 3 Disp lay: Da nge r sy mbo l
" Pull off the road .
" Stop t he vehicle .
" Turn off the e ngine.
" Check the ma lf u nction ing system. Con ta ct
yo ur autho rize d Au di dea ler o r a q ua lified
wor kshop for assis tance .
Red symbols indicate a priority 1 ma lf u nction
- Danger!
W it h a pr iority 1 malfu nction, a red symbol
appears in the upp er center area of the dis- play
r:::;,
fig . 23. A drive r message ap pears as
well to exp lai n the ma lfunction in more de­
ta il. When this symbol appears ,
three warning
tones so und in succession . T he symbo l contin­
u es to flash unti l th e fault has been corrected.
If several priority 1 malfunctions are present,
the symbo ls appear in s uccession and rema in
for about
2 seconds.
The driver wa rning goes o ut after about
5 sec­
onds, but it can be bro ught up aga in at any
t ime by press ing the ISET I button
r:!;> page 2 7 .
Alt ernator fa il ur e
r:!;> pag e 28
Electrom echanical steering
r:::;,page20 1
USA models: Brake system
malfunction
r:!;> page 29
Canada models: Brake sys­
tem malfunction
r:::;,page29
En gine coolan t leve l too low/
e ngine coolant tempe rature
too h igh
c:::>page30
Eng ine oil pressure too low
c:::> page 30
Refill engine oil now
c:::> pag e 31
Stee ring malfunction
c:::> page 31
Ignition lock malfu nction
r:::;, page31
Hybrid drive *
r:::;,page 99, c;,page 105
E3 Alternator malfunction
If the . symbo l in t he instr ument pane l dis ­
play flashes, t hen t he re is a ma lfunction in t he
alternato r or the ve hicle elect ronics . A warn-
ing to the driver will appear, too. The driver
II>

30 Driver in formation d isplay
...L Engine cooling system malfunction
A malfunction in the engine cooling system
must be repaired as soon as possible .
If the . symbol flashes in the display, either
t he eng ine cool ant
temperature is too h igh or
the eng ine coolant
level is too low . A dr iver
message appears as well to explain the mal­
function in more detail. The d rive r warning
goes out afte r about 5 seconds, but it ca n be
b rought up a t any time by p ress ing the
!SE TI
button again.
Turn off engine and ch eck coolant l evel
• Pull off the road .
• Stop the vehicle .
• Turn off the engine.
• Check coo lant level¢
page 240.
• Add coolant if ne cessa ry ¢ page 241 .
• Co ntin ue d riving only after the eng ine cool­
ant warn ing/ indicato r light goes o ut.
• Contact your a uthorized Audi dea ler for as-
sistance if necessary.
If the engine coolant level is co rrec t, then the
radia tor fan may be the cause o f the malf unc ­
tion .
A WARNING
-If your veh icle should break down for
mechanical or other reasons, park at a
safe distance from moving traffic, turn off the engi ne and turn on the hazard
wa rning lights ¢
page 52, Emergency
flash ers.
-
- Never open the hood if you see or hea r
steam o r coolant esca ping from the en­
gine compa rtme nt - you risk being s cald­
ed. Wait until you can no longe r see or
hear steam or coo lant es caping.
- T he e ngine compartmen t of a ny veh icle
is a dan gerous area. Before you perform
any wor k in the engine compartment,
t ur n of the engine and allow it to coo l.
Follow the wa rning stickers ¢
page 226,
Engine compartment.
(D Note
Do not continue driv ing if the . symbo l
ill um inates . There is a mal function in the
engine cooling system -you could damage
your engine.
"l:::r. Engine oil pressure malfunction
T he red engine oil pressure warning symbol
requires immediate service or repair. Driving with a low
oil pressure indication is likely to
cause severe engine damage .
If the . symbo l on the disp lay flashes, the
engine oil pressure is too low. A driver mes­
sage appears as we ll to exp la in the malfunc ­
t io n in more detail. The dr iver warning goes
o ut afte r abo ut 5 seconds , but it can be
brought up at any t ime by p ressing the
~ 1s =ET= I
button ag ain.
Turn off engin e! O il pressure too low
• Stop the vehicle.
• Turn the engine off.
• Chec k the engine o il level ¢
page 238 .
• Contact yo ur au thorized Aud i deale r for as-
sistance if necessa ry.
Eng ine oil level too low
If the engine oil level is too low, add engine
o il
¢page 238.
Engine oil leve l correct
If the symbol . flashes even tho ugh the en­
gine oil leve l is correct, please contact your
nearest authori zed Aud i Dea ler for assistance.
Do not continue dr iving . Do not leave the en­
gine running
idle, either .
(D Tips
- The engine oil pressure symbol. is
not an indicator for a low eng ine oil lev­
e l. Do not rely on it. Instead, check the
oil level in your engine at regular inter­
vals, preferably each time you refuel, and always before going on a long trip .

-The yellow oil level warning indication
II requires oil refill or workshop serv­
ice without delay. Do not wait until the
red oil pressure warning. starts to
flash before you respond to the low oil
level warning
11-By then, your engine
may already have suffered serious dam­
age .
~ . Fill engine oil now
WARNING: Please add oil immediately
If the . symbol lights up, then the o il has to
be re plenished r ight now ~
page 238 .
~- Steering malfunction
If there is a malfunction in the electronic
steering column lock, the steering cannot b e
unloc ked .
If the . symbol i n the display blinks , th ere
i s a malfunction in the electronic steer ing col­
u m n lock . A driver message a ppears as well to
e xplain t he malfu nction in m ore deta il. The
d river war ning goes ou t a fter abou t
5 se c­
on ds, but it can be brough t up at an y time by
p ress ing t he
ISE TI but ton again.
Steering defective! Do not drive vehicle!
.,. Co ntact your nearest authorized Audi deal ­
er .
.,. Do
not tow yo ur vehicle .
A WARNING
Your vehicle must not b e towe d in th e
eve nt of a m alfu nction in the ele ctronic
s t eerin g colum n lo ck bec ause i t ca n not be
steered due to the l ocked steering . If it is
towed with the stee ring loc ked, t here is
the risk of an accident.
© -Ignition lock malfunction
A mal function in the ignition lock mus t be re ­
paired immediately .
If th e. symbol in the d isp lay blink s, there
i s a ma lfunc tion in the elec troni c ignition lo ck.
Driver information display 31
A dr iver message appea rs as we ll to ex plain
t h e malfunction i n mo re deta il. The dr iver
warning goes out after a bout 5 seconds, b ut it
can be b roug ht up at any time by pressing the
ISE TI b utt on again.
Ignition lock defective. Contact dealer!
.,. Do not tu rn th e e ngine o ff.
.,. Drive imme diate ly to an a uthor ized A udi
dea le r to have t he mal funct io n corrected .
If there is a mal fun ctio n in t he ele ct ro nic igni­
tio n loc k, the igni tion can not b e turne d off.
Drive immediate ly to an au tho riz e d se rvice fa­
c ili ty to have t he cause of t he malfunct ion cor­
r ected .
On vehicle s wi th Conven ien ce key* , the eng ine
s h ould not b e swi tc h ed off usin g th e S tart/
Stop button because t he engine cannot be
started again afte r th e ignit io n has been
switc hed off.
· Yellow symbols
A yellow symbol me ans WA RNING .
Fig. 24 Display: Yellow wa rning symbo l
N ..,
I
Yellow symbo ls ind icate a prior ity 2 malfunc­
tion -Wa rning!
When a yellow warn ing symbol appears,
one
warning to ne sounds . A d river message ap­
p ears as well to exp lai n the ma lfu nction in
m ore d etail. T he d rive r war ning goes out aft er
abo ut 5 seconds, but it ca n be broug ht up a t
any ti me by press ing t he
ISE TI button again .
Check the function displayed as s oon as possi­
ble. The yellow symbol will not go out again
u nti l th e re ason fo r the mal func tion has bee n
cor rected.

32 Driver in formation d isplay
If several priority 2 malfunctions a re present,
the symbols appear in succession and remain
for about 2 seconds .
,1,ij
Electromechanical steering,
Dynamic steering*
¢ page 201
•
Worn brake pads
¢page 33
&1
Battery voltage
¢page34
;....
J:J
Defective light bulb
¢page33
II
Fog lights
¢page 33
.... -
II
Rear fog ligh ts
¢page33
•
Check engine oil leve l
¢page34
Ill
Engine oil sensor malfunc-
tion
¢page34
•
Engine temperature*
¢page229
II
Low fuel level
¢page33
•
Windshield washer flu id level
low
¢ page33
!I
Convenience key *
Key not
in vehicle
¢page32
m
Light/rain sensor defective
¢page33
II
Dynamic headlight range
control defective
¢page34
I!
Battery in remote control key
¢ page 37
-
rm
.,
-
Ill
m
B
m
[DJ
11NIB
6HVBRID
(D Tips
E
lectromechanical parking
bra ke
¢page 91
Engine speed limitation *
¢ page 34, ¢ page 99
Adaptive light defective *
¢page34
Ignition lock malfunction
¢ page34
Adaptive dampers *
¢page35
Windshield wiper defective
¢page35
Tire pressure monitoring sys­
tem*
L oss of tire pressure
¢page267
Tire pressure monitor ing sys­
tem*
System not avai lab le
¢ page 267
Automatic transmission mal-I
function
¢page 128 j
Hybr id dr ive *
¢page99
The speed warnings warn ing thresho ld 1
Ct] and warning thresho ld 2 [i] are also
yellow symbo ls in some models . The warn­
i ng is always shown as a small symbo l in
the upper a rea of the display ¢
page 93.
.Je Key not in vehicle
Applies to veh icles: w ith Convenience key
!I Is the key in the vehicl e?
Th is rem inder appears along with the !I sym­
bo l if the master key is removed from the ve­
hicle with the eng ine runn ing. It is intended
to rem ind you (e.g . whe n ch ang ing dr ivers) .,.

not to continue the journey without the mas­
ter key.
If the master key is no longer in the vehicle,
you cannot sw itch off the ignition after stop­
ping the engine and you a lso cannot start the
engine again . You also cannot lock the vehicle
from the outs ide.
~ o Light/rain sensor defective
ral A utom atic he adlight s/ autom atic wi pers
d efect ive
If the symbol illuminates, the light sensor has
fa iled. For safety reasons the low beams are
turned on permanently with the switch in
A U­
TO . However, you can continue to turn the
lights on and off us ing the light switch . In the
case of a defect in the rain sensor, the w ind­
sh ie ld wiper lever functions are st ill available .
H ave the light/rain sensor checked as soon as
possible by an autho rized Aud i dea ler.
(0) Worn brake pad s
[IJ Brake pad s!
If the warn ing l ight illum inates, immediately
contact your authorized A udi dealer or quali­
fied workshop to have all brake pads inspect­
ed . On USA models the warning light
[IJ
comes on together with the warning light
1111 . Both sets of brake pads on an axle
must always be replaced at the same time.
A WARNING
Dr iv ing with bad brakes can cause a coll i­
sion and serious personal injury.
- If the warning light
[IJ and the warning
light
11111> w ith the message B rak e
pads!
comes on in the instr ument cluster
display, immediately contact your au­
tho rized Aud i deale r or qualified work­
shop to have a ll brake pads checked or
replaced if necessary.
1) - : USA mod els only
-
Dri ver information di spla y 33
~!}010 $ Defective light bulb warning
I -If the ind icator light tu rns on, a bulb has
failed . The message ind icates the location of
the bu lb.
II -If a front fog lamp has fa iled, the ind ica­
tor light tu rns on to indica te the location on
the vehi cle.
ml -If a rear fog lamp has fa iled, the indica­
tor light turns on to indicate the location on
the ve hicl e.
Veh icl e light s: Sys te m fault!
If the message appears, there is a malfunc­
tion in the headlights or light sw itch.
Drive to your authorized A udi dealer immedi­
ate ly to have the malfunction corrected.
A WARNING
- Light bulbs are pressurized and could ex­
plode wh ile they are being changed caus­
ing serious personal injury.
- Work with due care when handling the high-voltage section of gas discharge
(xenon) lights* . Failure to do so could re­
sult in death or serious injury .
(D Tips
Have the bulb replaced or the connection
repaired by your authorized Audi Service
department .
o:> Windshield washer fluid level too
low
- Please re fill w asher fluid
If the symbol il lum inates, add w indshield
washer flu id to the washer system and also to
the headlight washe r system
c::> page 247.
Eli) Fuel supply too low
When the Ii'] symbo l ill uminates, this means
there a re abo ut 2.6 gallons (10 liters) o f fuel ..,.