brakes AUDI Q5 2014 Owners Manual

16 Instruments and warning/indicator lights
If the Jj;] indicator light turns on, the system
has switched the ESC
off . In this case, you can
switch the ignition
off and then on to switch
the ESC on again. The indicator light turns
off
when the system is functioning fully.
If the
11 indicator light turns on, ESC was re­
str icted using the
I~ OFF I button ¢ page 197.
Stabilization control (ESC/ABS): Fault! See
owner's manual
I f the
Jj;] indicator light and the ABS ind icator
l ight ~ (USA models)
Iii] (Canada models)
turn on and the message appears, the ABS or
e lectronic differential lock is ma lfunctioning.
This a lso causes the ESC to malfunction . The
brakes st ill function with the ir normal power,
but ABS is not active.
Drive to your authorized Audi dea ler or quali ­
fied workshop immediately to have the mal­
function corrected.
A WARNING
-
If the ~ (USA models)/ . (Canada
models) brake system ind icator light turns
on together with the ABS and ESC ind ica­
tor lights, the ABS/ESC regulating function
may have fai led. Functions that stabilize
the vehicle a re no longer ava ilab le. This
could cause the vehicle to swerve and in­
crease the risk of sliding. Drive carefully to
the nearest a uthorized Audi dea ler or oth­
er qualified workshop and have the mat-
function corrected.
(D Tips
For additional information on ESC and
ABS, refer to¢
page 197.
it !f Safety systems
The fl (USA models) tE,I (Canada models) in­
dicator light monitors the safety systems (e.g.
a ir bags, pretensioners) and illuminates for a
few seconds each time you switch the ignition
on .
If the
fl (USA models) tE,I (Canada models)
indicator light does not go out, or if it illumi- nates while you are driving, or if it starts to
blink,
then there is a malfunction somewhere
in the system. If the light does not illuminate
when you switch the ign ition on, this also
means there is a malfunction.
A WARNING '"--
If you have a malfunction in the safety sys-
tems, contact your authorized Audi dealer
imme diately. Otherwise the safety sys­
tems may not work properly in an acc i­
dent.
ill Tire pressure monitoring system -
telltale indicator lamp
Applies to vehicles: wit h tire p ressu re mo nito rin g system
The warning/indicator light appears in the
event of a significant loss of tire pressure or if
there is a malfunction .
The ind icator light IE illuminates to check
the function when you switch on the ignition.
If the
IE symbol remains on or blinks after
you sw itch on the ign it ion, there is a loss of
t ir e pressure or a system malfunction. If there
is a system ma lfunction, see your authorized
Audi dealer as soon as possible.
Detailed informat io n on the tire p ressure
monitoring system can be found in
¢page 265.
¢¢Turn signals
The indicator light blinks when you use either
turn signal.
Whenever you use the left (I or the r ight II
turn sig nal, the indicator light blinks. When
you use the emergency flashers, both indica­
tor lights flash .
If one of the turn signa l light bulbs burn out,
the turn sig nal will blink twice as fast as nor­
mal.
This does not apply, however, in towing mode .
The indicator light does not flash if a turn sig­
nal is out on the tra ile r or the towing vehicle. .,.

18 Instruments and warning/indicator lights
Malfunction in the brake system
If the brake warning light c::> page 18 and
the ABS warn ing illuminate
together there
may be a ma lfunction in the ABS, and there
may also be a malfunction in the brake system
itself
c::> A .
In the event of a malfunction in the brake
system
the warning/indicator light 1111
(USA models);II (Canada models) in the in­
strument cluster flashes. By pressing the
! SET !
button, you can bring up a dr iver message
which explains the malfunction in more de­
tail. Please note
c::> page 29.
Malfunction in the electron ic differential
lock (EDL)
The EDL works together with the ABS. The
ABS warning light will come on if there is a
malfunction in the EDL system
c::> page 197.
See your authorized Aud i dealer as soon as
possib le.
.&_ WARNING
-
- If the~ (USA models) l[!J (Canada
mode ls) warning light does not go out,
or if it comes on while driving, the ABS
system is not working properly. The vehi­
cle can then be stopped only with the
standard brakes (without ABS). You will
not have the protection ABS provides.
Contact your authorized Aud i dealer as
soon as poss ible.
- If the
1111 (USA models)/. (Canada
mode ls) brake system indicator light
turns on together with the ABS and ESC
indicator lights, the ABS/ ESC regu lating
function may have failed. Functions that
stabilize the vehicle are no longer availa­
ble. This could cause the vehicle to
swerve and increase the risk of sliding.
Drive caref ully to the nearest authorized
Audi dealer or other qualified workshop
and have the malfunction corrected.
::\ii(®) Electromechanical parking brake
The warning/indicator light monitors the
electromechanical parking brake.
With the parking brake applied and the igni­
tion turned on, the. (USA models)/ . (Can­
ada models) warn ing/ indicator light illumi­
nates. After the ignition has been turned off,
the warn ing/ indicato r light continues to illu­
minate for about 30 seconds.
If the parking
brake is applied with the ignition turned off,
the warn ing/indicato r light illuminates for
about 30 seconds.
T he wa rning/i ndicator lig ht will go out when
the parking brake is released.
If the warning/indicator light flashes continu­
ously
after applying the pa rking brake, brak­
ing force is not sufficient to prevent the veh i­
cle from rolling unintentionally . Please note
the following:
- If the slope of the ground is too steep to
pa rk the vehicle, the additional drive mes­
sage appears Caution : Vehicle parked too
steep.
- In the event of a pa rking brake malfunction,
the yellow
IIJ symbo l appears in the instru­
ment cluster display and the driver message
Parking brake malfunction! is displayed.
Have the ma lfunction repa ired as soon as
possible by an authorized Audi dealer or any
other qualified workshop.
BRAKE/((D) Brake system
The warning/indicator light flashes if brake
fluid level is low, if there is an ABS system
malfunction or a parking brake malfunction.
The 1111 (USA models)/ . (Canada models)
li ght illuminates when the ignition is turned
on. It goes out after the engine has been
started . This indicates that the brake warning
l ight is functioning properly.
If the brake warning light does not light up
when the engine is cranking, there may be a
malfunction in the electrical system. In this
case, contact an authorized Audi dealer. ..,.

Instrument s and warnin g/indic ator ligh ts 19
If the brake system warning/indicator light
flashes, there is a brake system malfunction. By pressing the
ISETI b utton, you can br ing up
a driver message which exp la ins the malfunc­
tion in more detail¢ page
29.
If the ABS fails, the ABS warning/indicator
light
fJln (USA models) ,11J (Canada models)
flashes together w ith the brake system warn­
ing/indicator light¢,& .
(USA models): If the warning light
11111 and
the warning light
EIJ i llum inate together, im­
mediately contact your author iz ed Audi dealer
or qualified workshop to have all brake pads
inspected ¢ page
33 .
When the light comes on, an audib le warning
signa l is also given.
A WARNING
- If the 11111 (USA models)/ . (Canada
models) brake system indicator light
tu rns on together with the ABS and ESC
indicator lights, the ABS/ESC regu lating
function may have failed. F unctions that
stabilize the vehi cle are no longer availa­
ble. Th is could cause the vehicle to
swerve and increase the risk of sliding .
Drive carefully to the nearest a uthorized
Audi dealer or other qualif ied workshop
and have the malfunction corrected.
- If the brake warning/indicator light does
not go out after a few seconds and the
parking brake is released, or lights up
wh ile you are driving, the fluid level in
the brake fluid reservoir is too low . If you
believe that it is safe to do so, proceed
immediately at low speed to the nearest
au thori zed Audi dealer o r qualified re pair
f acili ty and have the brake system in­
spected.
- Always keep in m ind tha t after several
brake applicat ions, yo u will need greater
pressure on the brake peda l to sto p your
vehicle. Do not re ly on stra ined brakes to
respond w ith maxim um stopp ing power
in critical situations. You must allow for
increased braking distances. The extra distance used up by fading brakes could
lead to an accident.

-Ze Key not in vehicle
Applies to vehicles: with Convenience key
l!I Is the key in the vehicle?
This reminder appears along with the l!I sym­
bol if the master key is removed from the ve­
hicle with the engine running. It is intended
to remind you (e.g. when changing drivers)
not to continue the journey without the mas­
ter key.
If the master key is no longer in the vehicle,
you cannot switch off the ignition after stop­
p in g the engine and you also cannot start the
engine again . You also cannot lock the vehicle
from the outside.
@9 Light/rain sensor defective
El Automatic headlights / automatic wipers
defective
If the symbol illuminates, the light sensor has
failed. For safety reasons the low beams are
turned on permanently with the switch in
AU­
T O . However, you can continue to turn the
lights on and off using the lig ht switch. In the
case of a defect in the rain sensor, the w ind­
shield w iper lever functions are st ill available.
H ave the light/ra in sensor checked as soon as
possible by an autho rized Aud i deale r.
(0) Worn brake pads
li1 Brake pads!
If the warn ing light illuminates, immediately
contact your authorized Audi dealer or quali­
fied workshop to have all bra ke pads inspect­
ed. O n USA models the warning
light lil
comes on together with the warning light
1111. Both sets of brake pads on an axle
must always be replaced at the same time .
A WARNING
Driving with bad brakes can cause a colli­
sion and serious personal injury.
1) - : USA mod els only
-
Driver information display 33
-If the warning light li1 and the warning
light
llll1l with the message Brake
pads!
comes on in the instrument cluster
disp lay, immediately contact your au­
thorized Audi dealer or qualified work­
shop to have all brake pads checked or
replaced if necessary.
~!}010$ Defective light bulb warning
f:;:1-If the indicat or light turns on, a bulb has
fa iled. The message indicates the location of
the bulb.
II-If a front fog lamp has failed, the indica­
tor light tu rns on to indica te the locat ion on
the vehicle.
0 -If a rear fog lamp has failed, the indica­
tor light turns on to indicate the location on
the vehicl e.
Vehicle lights: System fault!
If the message appears, there is a malfunc­
tion in the headlights or light switch.
Drive to your authorized A udi dealer immedi­
ate ly to have the malfunction corrected.
A WARNING
- Light bulbs are press urized and could ex­
plode wh ile they are being changed caus­
ing serious personal injury.
- Work with due care when handling the
high-voltage section of gas discharge
(xenon) lights*. Failure to do so could re­
sult in death or serious injury .
(D Tips
Have the bu lb replaced or the connect ion
repaired by your authorized Audi Service
department .
c> Windshield washer fluid level too
low
- Please refill washer fluid

76 Seats and storage
The 12-volt sockets can be used for electrical
accessories. The power input must not exceed
120 watts.
There is an additional 12-volt socket in the
center console. Before you purchase any accessories, always
read and follow the information in
Q page 295, Additional accessories and parts
replacement.
A WARNING
The power outlets and therefore the elec­
trical accessories connected to them oper­ ate only with the ignition on. Improper use
of the outlets or of electrical accessories
can lead to serious injuries or cause a fire.
For this reason, children should never be
left unattended in the vehicle -they could
be injured!
(D Note
To avoid damaging the socket, only use
plugs that fit properly .
{D) Tips
When the engine is off and accessories are
still plugged in and are on, the vehicle bat ­
tery can still be drained .
Storage
General overview
There are numerous places to store items in
your vehicle.
Glove compar tment Q page 76
Cooling box in glove com part-Qpage 77
ment
Storage compartment in the
Qpage 77
roof
Coat hooks
Qpage 77
Storage in the door panels
Storage net in footwell
-
Storage net in the front seat- backs
Storage net in luggage com- partment
A WARNING
--
- Always remove objects from the instru­
ment panel. Any items not put away
could slide around inside the vehicle
while driving or when accelerating or
when applying the brakes or when driv­ ing around a corner.
- When you are driving make sure that
anything you may have placed in the cen­
ter console or other storage locations
cannot fall out into the footwells. In case
of sudden braking you would not be able
to brake or accelerate.
- Any pieces of clothing that you have
hung up must not interfere with the driv­
er's view. The coat hooks are designed
only for lightweight clothing. Never hang
any clothing with hard, pointed or heavy
objects in the pockets on the coat hooks .
During sudden braking or in an accident -
especially if the airbag is deployed -
these objects could injure any passen­
gers inside the vehicle.
Glove compartment
The glove compartment is illuminated and
can be locked .
Fig. 90 Glove co mpartm ent
To open glove compartment
.,. Pull the handle in the direction of the arrow
Q fig. 90 and swing the cover down to open . ..,.

-When starting on inclines, the starting as­
sist prevents the vehicle from unintentional­
ly rolling back. The braking force of the
parking brake is not released until sufficient
driv ing force has been built up at the
wheels .
Emergency brake function
An emergency brake ensures that the vehicle
can be slowed down even if the
normal brakes
fa il
c::> page 90, Emergency braking.
Indicator light s
-If the parking brake is closed with the igni­
tion
s witched on the indicator lights come
on . (USA mode ls)/ . (Canada mode ls) in
the instrument cluster and the switch.
- If the parking brake is closed with the igni­
tion
s witched off the indicator lights come
on . (USA mode ls)/ . (Canada mode ls) in
the instrument cluster and the switch for
about 20 seconds.
A WARNING
If a drive range is engaged with the veh icle
stat iona ry and the engine running, you
must in no instance accele rate ca re lessly.
Otherw ise the vehicle will sta rt to move
immediately -risk of an accident .
(D Note
If the symbo l. in the display or the ind i­
cato r light .. (USA models) . (Cana­
da mode ls) in the instrument clus ter flash ­
es, the re is a malfunction in the brake sys­
tem . By pressing the
ISETI button, you can
bring up a driver message which explains
the malfunction in more detail.
If the driv­
er message
Parking brake system fault!
See owner's manua l
appears, there is an
operating malfunction in the park ing brake
which you should have repaired immedi­ ately by an author ized Audi dealer or other
qua lified workshop
c::> page 29.
@ Tips
- You can apply the pa rking brake at any
time -even w ith the ignition switched
'
On th e ro ad 89
off. The ignition must be turned on and
the brake pedal must be pressed in order
to release the parking b rake .
- Occasional noises w hen the parking
brake is app lied and released are normal
and are not a cause for concern.
- When the vehicle is pa rked, the parking
brake goes through a self -test cycle at
regu lar inte rva ls. Any associated noises
are normal.
Parking
"' Press the brake pedal to stop the veh icle.
"' Pull the sw itch
c::> page 88, fig. 100 to set
the parking b rake.
"' Move the selector lever to P.
"' Tu rn the engine off
c::> ,&. .
"'When on inclines or decl ines, turn the steer ­
ing wheel so that the vehicle will roll into
the cu rb if it begins to move.
A WARNING
-When you leave your vehicle -even if on­
ly briefly- always remove the ignition
key. T his app lies particularly whe n chil­
dren remain in the vehicle. Otherwise the
children could start the eng ine, release
the par king brake or operate elect rical
eq uipment (e.g. power w indows). The re
is the risk of an acc ident.
- When the veh icle is locked, no one -par­
ticularly not children should rema in in
the vehicle. Locked doors make it more difficult for emergency workers to get in­
to the vehicle -putting lives at risk.
Starting from rest
The starting assist function ensures that the
parking brake is released automatically upon
starting .
Stopping and applying parking brake
"' Pull the sw itch to app ly the parking b rake. .,.

(30 km/h to 240 km/h). Settings can each be
adjusted in intervals of
5 mph (10 km/h) .
Cruise control
Switching on
The cruise control sys tem makes it possible to
drive at a constant speed starting at 20 mph
(30 km/h) .
0
f
®t
0
Fig. 10S Contro l lever wi th push -bu tton
Fig. 106 Di splay: Selec ted speed
.. Pull the lever to position (D c:? fig . 105 to
switch the system on .
.. Drive at the speed to be contro lled.
.. Press button @to set that speed .
The stored speed and the ind icator light
Bll!lm (US model)/ il (Canad ian model) ap­
pear in the instrument cluster disp lay
<=> fig . 106. The display may vary, depending
on the type of display in your vehicle.
The speed is kept constant by modify ing en­
gine power or through an active brake inter­
vention.
A WARNING
- Always pay attention to the traffic around you when the cruise control is in
operation . You are always responsible for
c:o ;:g 0 ci: c:o al
On th e road 95
your speed and the distance between
your vehicle and other vehicles.
- For reasons of safety, cruise control
should not be used in the city, in stop­
and-go traffic, on twisting roads and
when road conditions are poor (such as
ice, fog, gravel, heavy rain and hydro ­
plan ing) - you could have an accident.
- Switch the cruise control off temporarily
when dr iv ing in turning lanes, h ighway
exits or in construction zones .
- Please note that unconsciously "resting" your foot on the accelerator pedal causes cru ise contro l not to brake. This is due to
the control system be ing overridden by
the driver's acceleration.
- Never use the cruise control when driving off-road or on unpaved roads. The c ruise
con tro l is intended for use only when the
vehicle is being operated on paved roads,
and is not suitable for use off-road or on
unpaved roads.
- If a brake system malfunction such as overheating occurs when the cruise con ­
trol system is switched on, the braking
function in the system may be switched off. The other cruise control functions re­main active as long as the indicator light
IR;\1 )~14 (US model)/ fil (Canadian model)
1s on .
(D Tips
The brake lights illuminate as soon as the
brakes apply automatically .
Changing speed
.. To increase/decrease the speed in incre­
ments, tap the lever in the
0 10 direction
<=> page 95, fig. 105 .
.. To increase/decrease the speed quickly, hold
the lever in the
0 10 direction until the de­
sired speed is displayed.
You can also press the accelerator pedal down
to increase your speed, e.g . if you want to
pass someone. The speed you saved earlier

(!) Fuel efficient driv ing within the
comb ustion engine's partia l
l oad range
@ System limits fo r electric d riving
i n the EV mode
® Elect ric driving or d riving w it h
the combustion engine (EFFI -
CI ENCY)
© Vehicle d rive ready (READY)
® H igh vo ltage bat tery c ha rge sta -
tus
® Recuperation (CHARGE)
0 Dr iving w it hi n the combus tion
engine's fu ll loa d range
® 100% combust io n engine
® Boost ing -the elect ric e ngine
assists the combus tion engine
( B OOST)
@ Engaging the conventiona l
brakes w ith recuperat ion
@ Vehicle not drive ready ( OFF)
@ EV mode active
The needle rema ins at
OFF when the igni tion
is tur ned on. W hen the veh icle en ters drive
ready mode, t he stat us message
hybrid ready
ap pears briefly in the instrument cluster dis ­
p lay and the needle in the power meter po ints
to
READY .
Indicator lights and messages
Applies to vehicles: with hybrid drive
The indicator lights in the instrument cluste r
b link or t urn on . Th ey i ndicate fu nctions o r
malfunct ions .
W ith some ind icator lights, messages may ap­
pear and a warning tone may sound. Also note
the indicator lights in c::,;,
pag e 27.
Press brake pedal to start vehicle
This message appea rs if you do not press the
brake peda l when starting the vehicle.
Hybrid 99
Shift to N or P to start vehicle
T his mess age appears if the se lector lever for
the automatic t ransmission is not in t he N or
P positions when starting the vehicle.
- Hybrid drive: System fault! Power
brakes, steering malfunction possible
I f the indica tor ligh t turns on and this mes ­
sage a ppears, t here is a ma lf u nction in the hy­
bri d system. The brake booster and the power
steering may stop working. Stop the vehicle i n
a safe l ocat io n as soo n as poss ible.
You may cont in ue dr iving if the indicator light
turns
off afte r start ing the ve hicle severa l
times. Dr ive to an a uthorized repa ir facility
immediately to have the malfunct ion correct­
ed .
EHithjj,j Hybrid drive : Sy stem fault!
Contact dealer
If the indicator light turns on and this mes­
sage appears , there is a malfunct ion in the hy­
br id system . Drive to a n author ized repair fa ­
c ili ty immediat ely to hav e th e m alfunc tion
corrected.
Ill Hybrid system: Performance
restricted. Please contact dealer
If th e i ndica to r light turns on and this mes­
sag e appea rs, there is an engine contro l ma l­
f unct io n .
The @B indi cator light in t he instr u­
m ent cluster also tur ns on. The engine ou tput
i s re duced. Drive to yo ur autho rize d Au di dea l­
er or qualifie d repair facility immediately to
have the malfunct io n corrected .
Hybrid drive deactivated. Please restart
engine manually.
Th is message ap pears if the high vo ltage bat­
te ry charge leve l has fallen below a certa in
range or if the ignition key is no longer inside
the ve hicle for ve hicles with the convenience
key *.
Start the eng ine with e it h er the ignitio n key
¢page 83 or with the !STAR T EN GINE STOPI
button* c::> page 86.

-Offroad mode and hill descent assist must
not be turned on
c::> page 198.
The combust ion eng ine tu rns on and inter­
rupts
the enhanced electric d rive mode when
the vehicle is accelerated. The gray indicator
light
l:!I also turns on in the disp lay. The en­
hanced electric drive mode resumes automati ­
cally once acceleration stops.
The enhanced e lectric drive mode is
deactivat­
ed
if at least one of the following conditions is
met :
- Th e ign ition is turned off.
- Th e
1.:1"1 button is pressed again.
- The high voltage battery charge level is low .
- The veh icle speed is higher than approxi -
mately 62 mph (100 km/h).
- The
S selector lever position or tiptronic
mode is selected .
- Offroad mode or hill descent assist is
switched on .
T he
ld" I button must be pressed to reactivate
it .
Start-Stop function
The combustion engine is operated on ly as
needed. Generally, the combustion engine
turns off when the vehicle is stationary and
the high voltage battery powers the electrical
vehicle systems.
The purpose of automatica lly shutting the
combustion engine off in hybrid drive mode is
to save fuel. All of the important veh icle sys­
tems, such as steering, brakes and the A/C
system, cont inue to remain active. In some
cases, systems may require the combustion
engine to cont inue running when the vehicle
is stationary. When dr iv ing in congested traf­
fic for long per iods of time, the combustion
engine w ill cycle on when the vehicle is sta­
tionary to keep the high voltage battery
charged.
Gliding
I f the gas pedal is not pressed and the D posi­
tion is selected, the combustion engine re-
Hybrid 101
mains turned off up to speeds of approxi ­
mately 99 mph ( 160 km/h) . Driving conserva­
tive ly like this can reduce fuel consumption .
Energy recovery (recuperation)
When braking, the elect ric motor will act as a
generator creating e lectric energy that is then
stored in the high voltage battery. This also
occurs when the ve hicle is coasting or driving
downhi ll. The combustion engine is automati­
cally turned off in this case.
The vehicle is braked with the electric motor
by applying ear ly and even pressure to the
brakes and using short pedal movements
¢ page 98, fig. 107 @. By doing this, a large
amount of the kinetic energy is recovered and may be stored as electric energy in the high
voltage battery. During heavy braking, the
convent ional brakes are also act ivated
c::> page 98, fig. 107 @.
The energy recovery is shown in the MMI dis­
play
c::> page 104 .
Automatic start of the combustion engine
Various operating conditions cause the com­
bust ion engine to start automat ically :
- The high voltage battery charge leve l is low.
- The temperature of the comb ustion engine
is low.
- The temperature of the catalyt ic converter is
low .
- The power output needed for the A/C sys-
t em is high.
- The vehicle speed is hig h.
- The vehicle acceleration is high.
- The inclin e is steep.
- High charge level for the high voltage bat-
tery when coasting. In th is case, the h igh
voltage battery cannot absorb any mo re en­
ergy and so the electric motor cannot slow
down the veh icle. The combustion engine
tu rns on (engine brake). In this situation the
h igh voltage battery will show a Ma x charge.

102 Hybrid Tips for Driving Efficiently with your Hybrid
Applies to vehicles: with hybrid drive
Driving situa-
Conditions Vehicle behavior
tions
-Shift into the D position.
In the D position, the hybrid system adapts
Starting from a -
Release the brake pedal. to the driving situation by automatically
stop -
Only press moderately on the ac- switching between the combustion engine
and electric drive types or by combining
celerator pedal.
them.
- Ca utious dr iv ing and reserved ac-
The kinetic energy of the vehicle is used to
ce leration . move the vehicle.
Constant driv-
ing and coasting -
Release the acce lerator pedal When you release the acce lerator pedal en-
early and entirely. ti rely, the combustion engine turns off au-
(gliding)
tomatically and is disengaged. The vehicle
glides without being propelled.
- Brake early and even ly with short The electric motor brakes the vehicle. By
Energy recovery pedal movements.
doing this
, a large amount of the kinetic
energy is recovered and may be stored in
( recuperation)
the high voltage battery in the form of
electric energy.
- Reserved acceleration and early The kinetic energy of the vehicle is used to
and even braking w ith short pedal move the vehicle.
movements .
Driving in city -
Use the
la• I button sparing ly. The battery drains quickly when the laVI
button is turned on, which can increase
traffic
fuel consumption because electric driving
is given priority, even if driving with the
combustion engine on would be more effi-
cient .
- Intentionally take your foot off When you release the acce lerator pedal en-
of the gas pedal to allow for ti rely, the combustion engine turns off au-
lengthy coasting . tomatically and is disengaged. The vehicle
glides without being propelled.
Driv ing on high- -
Reduce the vehicle speed by re-Fuel consumption can be reduced by coast-
ways and ex- l
eas ing the accelerator peda l and mg.
pressways not by braking.
- Avoid vehicle speeds above ajp -
It is possible to coast up to a veh icle speed
proximately 99 mph (160 km/h) . of approximately 99 mph (160 km/h).
- Use the S selector lever position A sporty driving style increases fuel con -
and tiptronic mode sparingly. sumption.