battery AUDI Q5 2016 Owner's Guide

..... N
co ~ CX)
..... I.Cl U"I
..... I.Cl .....
-Do not interchange the positive a nd nega­
tive cables.
- When working on the battery, be sure not to
short-circuit the terminals with tools or oth­
er metal objects. This would cause the bat­
tery to heat up very quickly, which could
lead to damage or explosion and personal
injury.
- When a battery is charged, it produces hy­
drogen gas which is explosive and could
cause personal injury.
- Always keep the battery well out of the reach of children.
- Before work is done on the electrical sys­
tem, disconnect the negative ground cable.
- Before performing any work on the electri­
cal system, switch off the engine and igni­
tion as well as any electrical equipment. The
negative cable on the battery must be dis­
connected. If you are just going to replace a
light b ulb, then it is enough to sw itch off
the lights.
- Before disconnecting the battery, switch off
the ant i-theft alarm system! Otherw ise you
will set off the a larm.
- When disconnecting the batte ry, first dis­
connect the negative cable and then the
positive cab le.
- Before reconnecting the battery, make sure
all e lectrical consumers are switched off .
Reconnect the posit ive cable first and then
the negative cable . Never interchange the
cables -this could start a fire!
- Never charge a frozen or a thawed-out bat­
tery. It could exp lode! If a battery has fro­
zen, then it must be replaced. A discharged
battery can freeze over at 32°F (0°C).
- Make sure the vent hose is a lways attached
to the opening on the side of the battery.
- Never use batteries which are damaged.
There is the danger of an explosion! Always replace a damaged battery.
A WARNING
California Proposition 65 Warn ing:
- Battery posts, termina ls and re lated acces­
sories contain lead and lead compounds,
C hecki ng an d Fill in g
chemicals known to the State of Californ ia
to cause cancer and reproductive prob lems.
Wash hands after handling.
(D Note
- Do not disconnect the vehicle battery when
the ignition is sw itched on or when the en­
gine is running, otherwise, you will damage
electronic components in the electrical sys­
tem .
- If your vehicle is going to stand for a long
period of time w ithout being driven, protect
the battery from "freezing", otherwise it
w ill be damaged and will then have to be re­
placed .
Battery charging
Starting the engine requires a well charged bat­
tery .
Fig . 202 E ngine compar tmen t: Co nn ectors fo r charg er and
j umpe r cables
Alw ays re ad and heed a ll WARN IN GS below
c;, ,& and r=;, .& in Working on the battery on
page 230 .
., Hybrid drive*: read the important information
concern ing a dead high voltage battery under
¢ page 104 .
., Turn off the ignition and a ll electrical consum­
ers.
... Make sure the area is we ll ven tilated when you
charge the battery .
... Open the eng ine hood
r=;, page 220 .
... Remove the cover (D by pressing on the arrow
¢ fig. 202 .
... Open the cover @on the pos itive terminal. ..,_
231

Check ing and F illing
"' Connect the charger connectors according to
the instr uctions to the
jump start bolts . (Bolts
u nder the cover = "posit ive", Bo lts with hex
head = "negative") .
"' Only now plug the mains lead for the charging
equipment into the wall outlet and tur n it on
¢& .
"' Make sure the charging rate is not over
30 amp s/14 .8 Volt.
"' When the batte ry is fu lly charged: T urn the
charg ing equipment off and remove the mains
lead from the wall outlet .
"' Now remove the clamps for the charg ing equip­
ment .
"' Close the cover @on the positive term inal and
re-install the cover@.
"' Close the hood
c:::;, page 220 .
A discharged battery can freeze at temperatures
of only 32 °F (0 °C). Allow a frozen battery to
thaw completely before attempt ing to charge it
c:::;, ,& . However, we recommend not us ing a
thawed batte ry again because the battery casi ng
can be cracked due to ice fo rmation and can leak
b attery acid.
Battery charging (Maximum charging rate of
30 amps/14.8 Volt)
W hen cha rging at low vo ltages (e .g . with a trick ­
le charger ),
the ba tte ry cables do not h ave to be
d isconnected first. The b att ery caps sho uld
no t
be opened when charging a battery.
It is not necessary to remove the batte ry from
the l uggage comp artme nt.
Fast charging the battery (charging rate
above 14.8 Volts)
F or techn ica l reaso ns do not use a battery charg­
er that uses vol tage greate r th an 14.8 Volts to
charge yo ur vehicle's bat tery.
A WARNING
Charging a ba ttery can be dangerous .
- Alw ays foll ow the operat ing instru ctions
p rovi ded by the bat tery char ger m anuf actur­
er when c harging your battery .
232
-Never cha rge a frozen battery . It may ex­
plode because of gas trapped in the ice. Al­
low a frozen battery to thaw out first.
- Do not reuse batter ies which were f rozen.
The battery housing may have cracked and
weakened w hen the battery froze.
- Charge the battery in a well ventilated area.
Keep away from open flame or electrical
spark. Do not smoke . Hydrogen gas generat­
ed by the battery is explosive.
- To reduce the da nger of explosion, never
connect or d isconnect c harger cables while
the charge r is ope ra ting .
- Fast c harg ing a battery is dange rous and
should o nly be attempted by a compe ten t
t echnicia n w ith the prope r equipment .
- Battery acid that may spill duri ng charging
should be washed off w it h a so lution o f
warm water and baking soda to neutra lize
t he a cid.
(D Note
Neve r use a fast c harge r as a booster to start
the eng ine . This will seriously damage se nsi­
tive electronic components, such as cont rol
units, re la ys, ra d io, e tc., as well as the batte ry
c h ar ger.
Battery replacement
The new battery must have the same specifica­
tions and dimensions as the original equipmen t
battery.
Intelligent energy manageme nt in yo ur vehicle is
r esponsib le for d istr ib uting t he e lec trica l energy
t hr oughou t your ve hicl e
c:::;, page 195 . The intelli­
gen t energy management system w ill keep the
engine battery charged bette r then vehicles with ­
out this system . To make sure the additional
e lectrica l ene rgy is available once aga in after you
have changed the batte ry, we recommend that
you install batteries of the same type and manu­
facture only (the same as those installed at the
time yo ur vehicle was delivered) . Specifications
a re listed on the ba tte ry ho using . Your a uth or-
iz ed dealer m ust code the battery in the energy
9"'

,...,
N
co ~ CX) ,...,
I.Cl U"I ,...,
I.Cl ,...,
management system to enable you to use the en­
ergy management functions correctly after re­
placing the battery.
If it is not possible to use a battery of this type,
the new battery must have the same capacity,
voltage (12 volts), amperage, construction and
plug sealing .
When installing the battery, make sure the igni­
tion and all electrical consumers are turned off.
CD Note
- Make sure the vent ilation hose on the side
of the battery is connected, otherwise
fumes or battery acid can leak out.
- Vehicles with the Start-Stop-System* are
equipped with a special cycle-proof AGM
battery. Installing a different type of bat­
tery can cause prob lems in the vehicle elec­
trical system. When replacing the vehicle battery, always install one with the same
spec ifications as the original battery.
@) For the sake of the environment
Because of the problem of proper disposal of
a battery, we recommend your authorized
Audi dealer change the battery for you. Bat­
ter ies contain sulfuric acid and lead and must
always be disposed of properly in compliance
with all environmental regulations. Disposing
of vehicle batteries imp roperly is very danger­
ous to the environment.
Windshield/headlight
washer container
Fig. 203 Engine compartment: cover on the windshield
and headl ight* washer flu id reservo ir
M N
-N
"' CX) CX)
Checking and Filling
The washer fluid container is marked with the
symbol
O on its cap ¢ fig. 203, ¢page 222,
fig. 197 .
.. Before you check anything in the engine com­
pa rtment,
always read and heed all WARN­
INGS ¢ A in Working in the engine compart­
ment on page 220 .
.. Lift the filler cap tongue to add washer fluid .
You can fill the container to the top .
.,. Press the cap back onto the filler neck after fill-
ing the co nta iner.
You can find the reservoir
capacity in the table in
¢page 277.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on the
washer jets. Always add a glass cleaner solution
(with frost protection in the winter).
CD Note
Do not mix engine coolant antifreeze or any
other additives to fill up the windshield wash­ er reservoir .
233

Wheels
(a) Curb weight
(b) Accessory weight
(c) Vehicle capacity weight, and
(d) Production options weight
Maximum (permissible )
inflation pressure
means the maximum cold infla­
tion pressure to which a tire may be inflated. Also called "maxi­
mum inflation pressure ."
Normal occupant weight
means 150 lbs . (68 kilograms)
times the number of occupants
seated in the vehicle up to the to­
ta l seating capacity of your vehi­
c le .
Occupant distribution
means distribut ion of occupan ts
in a vehic le .
Outer diameter
means the overall diamete r of an
inflated new tire.
Overall width
means the l inear distance be ­
tween the exter iors of the side­
walls of an infla ted tire , including
elevations due to labeling , deco­
rations, or protective bands or
r ibs.
23 8
Ply
means a layer of rubber -coated
pa rallel cords.
Production options weight
means t he comb ined we ight of
those insta lled regular production
options weighing over 5 lbs . (2 .3
kg) in excess of those standard
items which they replace , not pre­
viously considered in curb weight or accessory weight, inc luding
heavy duty brakes, ride levelers,
roof rack, heavy duty battery, and
special trim.
Radial ply tire
means a pneumatic tire in which
the ply co rds that extend to the
beads are laid at subs tantially 90
deg rees to the centerline o f the
tread .
Recommended inflation
pressure
see~ page 23 7, Cold tire infla­
tion pressure.
Reinforced tire
means a tire designed to operate
at highe r loads and at h igher in­
flat ion pressures than t he corre­
spond ing standa rd tire . R ein ­
forced tires may be identified as .,.

Emerg ency assis ta nce
Emergency assistance
Vehicle jack, vehicle tool kit and collapsible spare
tire
Onboard tool kit and vehicle jack
The vehicle tools and vehicle jock* ore stored in
the luggage comportment under the floor cover.
Fig. 209 Luggage compartment: on board tool kit and vehi­
cle jack
The vehicle jack* is stored under the onboard tool
kit ¢ fig. 209.
Hybr id d rive*: the storage location of the on­
board tool kit varies ¢ page 104.
The onboard tool k it includes:
- Hook for removing wheel covers*
- Plastic hook to
remove wheel bolt covers*
-Alignment pin for changing wheels
- Wheel bolt wrench
- Folding chocks
- Screwdriver with revers ible blade
- Socket (removable Torx socket)*
- 10 x 13 open ended wrench (for disconnecting
the battery cables)
- Towing eye
A WARNING
Improper use of the vehicle jack* can cause
ser ious personal injuries.
- Never use the jack* supplied with your Aud i
on another vehicle, particularly on a heavier
one. The jack* is only su itable for use on the
vehicle it came w ith.
254 -
Using a bumper jack to raise the vehicle will
damage the bumper system. The jack may
slip, caus ing injury.
- Never support your vehicle on cinder blocks,
bricks or other objects. These may not be
able to support the load and could cause in­
jury when they fail.
- Never start or run the engine while the vehi­
cle is supported by the jack* .
- If you must work under the vehicle, always
use safety stands specifically designed for
this purpose .
- Never use the hexagonal socket in the han­
dle of the screwdr iver to loosen or tighten
the wheel bolts .
- Always make sure the inflatable spare tire*
and
even a flat tire are secu red in place and
not loose, otherwise they could fly forward,
causing personal inj ury to passenge rs in the
vehi cle in an a cc ident or sudden maneuve r.
@ Tips
The vehicle jack in your vehicle is mainte­
nance-free.
Folding chocks
The folding chocks ore port of the on board tool
kit .
---
Fig . 210 Open ing fo lding chocks
To use the chocks, you fi rst have to raise the sup­
port plate
¢ fig. 210 (D and then insert the lock­
ing plate with the two "tabs" into the elongated
holes in the base plate
@ c> &.. .,,_

Fuses and bulbs
Left cockpit fuse assignment
Fig. 224 Left side of the cockp it: fuse panel with p lastic
clip
Fuse panel @ (black)
No . Equipment
1 Dynamic steering
2 ESC control module
A/C system pressure sensor, electrome-
3 chanical parking
brake, Homelink, auto-
matic dimming interior rearview mirror,
air quality/outside air sensor, ESC button
s Sound actuator/exhaust sound tuning
6 Headlight range control/corner ing light
7 Headlight (cornering light)
Control modules (electromechanical park-
8 ing brake, shock absorber, quattro Sport,
trailer hitch), DCDC converter
9
Adaptive cruise control or high voltage
battery (hybrid dr ive)
11 Side assist
12 Headlight range control, parking system
13 Airbag
14 Rear wiper
15 Auxiliary
fuse (instrument panel)
16 Auxiliary fuse te rm inal 15 (engine area)
266
Fuse panel ® (brown)
No. Equipment
1 Electric exhaust door
2 Brake
light sensor or brake pedal move-
ment sensor (hybrid drive)
3 Fuel pump
4 Ad
Blue pumps or brake booster power
supply (hybrid dr ive)
s
Left seat heating with/without seat venti-
lation
6 ESC
7 Horn
8
Left front doo r (window regulator, central
locking, mirror, switch, lighting)
9 Wiper motor
10 ESC
11 L
eft rear doo r (window regulator, switch,
li ght ing)
12 Rain and light sensor
Fuse panel
© (red)
No. Equipment
3 Lumbar support
4 Dynamic steering
5 Climatized cupholder
6 Windshie
ld washer system, headlamp
washer system
7 Vehicle electrical system control module 1
8 Vehicle electrical system control module 1
9 Panorama roof
10 Vehicle electrical system control module 1
11 Sun shade (panorama sunroof)
12 Anti-theft alarm system

Fuses a nd bul bs
Fu se pa nel© (bro wn)
No. Equipment
1 Luggage compartment lid control module
2 12 V socket, cigarette lighter
3
DCDC converter path 1 or high vo ltage bat-
tery blower (hybrid drive)
4 DCDC converter path 2, DSP amp lifier, ra-
dio
7 Electromechanical
parking brake
9
Right front door (window regu lator, cen-
tral locking, mirror, switch, lighting)
11 Rear right
door (window regulator, switch,
lighting)
12 Cell phone preparation
F
use panel © (black )
No. Equipment
1 Rig ht
front seat heating/venti lation
2 Automatic dimming rearview mirror
3 Instrument
panel terminal 30
4 MMI
5 Radio
6 Rearview camera
7 Rear window defogger
8 Rear Seat Entertainment
11 AdBlue heating
12 Ad Blue supply or h
igh vo ltage battery (hy-
brid drive)
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out bulbs for you.
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re ­
moved before you are able to get to the bu lb.
This applies espec ially to the light bulbs in the
front of your ca r wh ich you can only reach
through the eng ine compartment.
2 6 8
Sheet meta l and bu lb holders can have sharp
edges that can cause serious cuts, and parts
must be correctly taken apart and then properly
put back together to help prevent breakage of
parts and long term damage from water that can
enter housings that have not been properly re­
sealed.
For your safety, we recommend that you have
your authorized Audi dealer replace any bulbs for
you, since your dealer has the proper tools, the correct bulbs and the expertise.
Ga s d ischar ge lam ps (Xeno n light s)*:
Due to the high e lectrica l voltage, have the bulbs
rep laced by a qualified technician. Headlights
with Xenon light can be identified by the h igh
voltage sticker.
A WARNING
-
Contact with high-voltage components of the
electr ical system and improper replacement
of gas discharge (Xenon) headlight bulbs can
cause ser ious persona l injury and death .
- Xenon bulbs are pressur ized and can ex­
plode when being changed .
- Changing Xenon lamps requires the special
tra ining, instruct ions and equ ipment .
- Only an authorized Audi dealer or other
qualified workshop should change the bulbs
in gas discharge lamps .
A WARNING
There are parts with sharp edges on the open­
ings and on the bulb ho lders that can cause
serious cuts.
- If you are uncertain about what to do, have
the wor k performed by an authorized Audi
dea ler or other qual ified workshop. Ser ious
personal injury may resu lt from improperly
performed work .
(D Tips
-If you must replace the light bulbs you rself,
always remember that the eng ine compart­
ment of any vehicle is a hazardous area to
work in. Always read and heed all WARN­
INGS¢
page 220 ¢ & .

Emergency situations
Emergency situations
General
This chapter is intended for trained emergency crews and working personnel who have the nec­
essary tools and equipment to perform these
operations.
Starting by pushing or
towing
CD Note
Vehicles with an automatic transmission
cannot be started by pushing or towing.
Starting with jumper
cables
If necessary, the engin e con be started by con­
necting it to the battery of another vehicle.
If the engine should fail to start because of a dis­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of sufficiently large cross
section
to carry the starter current safely. Refer
to the manufacturer's specifications.
Use only jumper cables with
insulated terminal
clamps which are distinctly marked :
plus(+) cable in most cases colored red
minus(-) cable
in most cases colored black.
A WARNING
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury. Follow the instructions below for
safe
handling of your vehicle's battery.
-Always shield your eyes and avoid leaning
over the battery whenever possible.
-A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C). Before con­
necting a jumper cable, you must thaw the
270
frozen battery completely, otherwise it could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water immediately.
- Improper use of a booster battery to start a
vehicle may cause an explosion.
- Vehicle batteries generate explosive gases.
Keep sparks, flame and lighted cigarettes
away from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery.
- The voltage of the booster battery must also
have a 12-Volt rating. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­
ly different "Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery. Gas trapped in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen . The battery
case may have be weak­
ened .
- Use of batteries of different voltage or sub­
stantially different capacity (Ah) rating may
cause an explosion and injury. The capacity
(Ah) of the booster battery should not be
lower than that of the discharged battery.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
~page 220.
CD Note
-Applying a higher voltage booster battery
will cause expensive damage to sensitive
electronic components, such as control
units, relays, radio, etc.
- There must be no electrical contact between
the vehicles as otherwise current could al­
ready start to flow as soon as the positive
(+) terminals are connected.
@ Tips
- The discharged battery must be properly
connected to the vehicle's electrical system. .,..

..... N
co ~ CX)
..... I.Cl U"I
..... I.Cl .....
When jump starting or charging the bat ­
tery, never connect the negative ground ca­
ble to tbe battery negat ive post because the
battery manager system must be ab le to de­
tect the battery's state of charge. Always
connect the negative ground cable to the
negative ground post of the battery manag­
er contro l unit .
Use of jumper cables
Make sure to connect the jumper coble clomps in
exactly the order described below!
Fig. 227 Engine co mpartment: Connectors for jumper ca ­
b les and charger
Fig. 228 Jump starting w ith the bat tery of a nother vehicle:
@ booste r battery, @ discha rged veh icle battery
The procedure described below for connecting
jumper cables is intended to provide a jump start for your vehicle.
Hybrid drive*: read the important information
concerning a dead high voltage battery under
c;;,poge 104.
Vehicle with discharged battery:
.. Turn off lights and accessories, move lever of
automatic transmission to N (Neutral) or P
(Park) and set parking brake .
Emergency situations
Connect POSITIVE(+) to POSITIVE (+) (red)
.. Remove the cover@ by pressing on the arrow
¢fig. 227.
.. Open the cover @on the positive terminal.
1. Connect one end of the red positive cab le on
the
jump start bolt r=;;, fig. 228 @ (Bolts un­
der cover= "positive") of the vehicle to be
started @.
2. Connect the other end to the positive termi-
nal @ of the booster battery @.
Connect NEGATIVE(-) to NEGATIVE(-)
(black)
3. Connect one end of the black negative cable
to the negative te rm i nal @of the booster
battery @.
4. Connect the other end of the bla ck negative
cable to the
jump start bolt@ (Bolts wi th
hex head = "negative") of the vehicle to be
started @.
Starting the engine
.. Start the engine of the vehicle with the booster
battery @. Run the eng ine at a moderate
speed .
.. Start engine w ith discharged vehicle battery®
in the usual manner .
.. If the engine fails to start: do not keep the
starter cranking for longer than 10 seconds.
Wait for about 30 seconds and then try again .
.. With eng ine running,
remove jumper cables
from both veh icles in the exact
reverse order .
.. Close the
cover @on the positive terminal and
re-install the cover (!)¢
fig. 227.
T he battery is vented to the outside to prevent
gases from entering the vehicle interior . Make
sure that the jumper clamps are well connected
with their
metal ports in full contact with the
battery term inals.
& WARNING ~
To avoid serious personal injury and damage
to the veh icle, heed all warnings and instruc­
tions of the jumper cable manufacturer. If in
doubt, call for road
service.
-Jumper cables must be long enough so that
the vehicles do not touch.
~
271

Emergency situations
-When connecting jumper cables, make sure
that they cannot get caught in any moving
parts in the engine compartment.
- Do not bend over the batteries -danger of
chemical burns!
- The battery cell locking screws must be
tightened securely.
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS
c> page 220.
(D Note
Improper hook-up of jumper cables can ruin
the generator .
- Always connect POSITIVE(+) to POSITIVE
(+), and NEGATIVE(-) to NEGATIVE(-)
ground post of the battery manager control
unit.
- Check that all screw p lugs on the battery
cells are screwed in firmly. If not, tighten
plugs prior to connect ing clamp on negative
battery terminal.
- Please note that the procedure for connect ­
i ng a jumper cable as described above ap­
plies specifically to the case of your vehicle
being jump started . When you are giving a
ju mp start to another vehicle , do
not con­
nect the negative (-) cable to the negative
(-) terminal on the discharged batte ry @
c> fig. 228. Instead, securely connect the
negative( -) cab le to either a solid metal
component that is firm ly bolted to the en­
gine block or to the engine block itself. If
the battery that is being charged does not
vent to the outside, escap ing battery gas
could ignite and explode !
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
The following information is to be used by com ­
mercial tow truck operators who know how to op­
erate the ir equipment safely.
-Never tow your Audi, towing will cause dam­
age to the engine and transmission.
272
-Never wrap the safety chains or winch cables
around the brake lines .
- To prevent unnecessary damage, your Audi
must be transported with a flat bed truck .
- To load the vehicle on to the flat bed, use the
towing loop found in the vehicle tools and at­
tach to the front or rear anchorage
i:>pag e 272 and i:> page 273.
A WARNING
A vehicle being towed is not safe for passen­
gers . Never allow anyone to ride in a vehicle
being towed, for any reason.
Front towing loop
Do not install the front towing loop until it is
needed.

Fig. 229 Front bumper : remov ing the cover cap

Fig. 230 Front bumper: s crew ing in t he towing loop
The towing loop fits into the threaded hole locat­
ed on the right side o f the front bumper and cov­
ered by a cover when not in use.
.,. Remove the towing loop from the vehicle tool­
kit
c> page 254 .
.,. Carefully remove the cove r c> fig. 229.
.,. Screw the towing loop tightly into the threaded
hole as far as it will go
c> fig. 230. Ill>