AUDI Q5 2021 Owner´s Manual

80B012721BA
Quick access

Vehicle sound
=> page 107
Drive system
=> page 107


























Brake system
=>page 110
Electromechanical parking brake
=> page 112
Suspension control
=>page 116
Air suspension
=>page 116
Steering
>page 117
Steering lock
=> page 117
All wheel drive
> page 118,
Sport differential
=>page 118
Electronic Stabilization Control
(ESC)
=> page 120
Electronic Stabilization Control
(ESC)
=> page 120
Electronic Stabilization Control
(ESC)
=> page 120
Anti-lock Braking System (ABS)
=> page 120
Anti-lock Braking System (ABS)
=> page 120
High-voltage battery range
=>page 129,
Tank system
=> page 242
Adaptive cruise control
=> page 162,
Traffic jam assist
=> page 163
Steering intervention request
=> page 163,
=> page 166

Distance warning
=> page 164
Active lane assist
=>page 165,
= page 167
Pre sense
=> page 167
Side assist, exit warning
=>page 172
Parking systems
=>page 176
Rear cross-traffic assist
=> page 181
Park assist
=>page 185
Emergency call function
=> page 203
Tank system
=> page 242,
=> page 242
Malfunction Indicator Lamp (MIL)
=> page 246,
Engine oil level (MIN)
=> page 250
Engine oil level (MAX)
=> page 250
Engine oil sensor
=> page 250
Engine warm-up request
=> page 250
Electrical system
=> page 256
Washer fluid level
=>page 259
Tire pressure
=> page 279,
=> page 279
Tire pressure
=> page 279

Other indicator lights
Low beam headlights
=> page 50 >
9

Quick access

Parking lights
=> page 50
Turn signals
> page 51,
=> page 52





















Turn signals
>page 51,
=> page 52
Plug-in hybrid modes
=>page 105
Start/Stop system
=> page 108
Hill hold assist
>page 114
Trailer turn signals
=> page 139
Cruise control system
=>page
151
Cruise control system
>page 151
Efficiency assist
=> page 153,
=> page 153
Efficiency assist
=> page 153
Efficiency assist
re => page 153
Efficiency assist
ou => page 153
Efficiency assist
=> page 153
Efficiency assist
=> page 153
Efficiency assist
=> page 153
Adaptive cruise control
=>page 155
Adaptive cruise control
=>page 155
Adaptive cruise control
>page 155
Adaptive cruise control
=>page 155
10
































Adaptive cruise control
=> page 160
Traffic jam assist
=> page 162
Traffic jam assist
=> page 162
Active lane assist
=>page 165
High beam headlights
=> page 51,
=> page 51
High beam assistant
> page 51
Child safety lock
=>page 45
Child safety lock
>page 45
Child safety lock
=>page 45
High beam assistant
=>page 51,
=> page 53
Convenience key
=> page 98
Transmission
=> page 103
Plug-in hybrid modes
=>page 105
Plug-in hybrid modes
=>page 105
Plug-in hybrid modes
=>page 105
Plug-in hybrid modes
=>page 105
Plug-in hybrid modes
=>page 105
Plug-in hybrid modes
=>page 105
Start/Stop system
=> page 109
Electromechanical parking brake
=> page 112 >

80B012721BA
Quick access

Pre sense
=> page 167



























Electromechanical parking brake
=>page 112
Pre sense
=>page 168
Hold assist
=>page 112
Hill hold assist
=>page 114
Side assist, exit warning
=> page 172
Steering
=> page 117
Parking systems
=>page 176
Rear cross-traffic assist
> page 181
Speed warning system
=>page 145
Park assist
=>page 185
Speed warning system
=>page 145

Park assist
=>page 185
Fuel filler door
=> page 242
Camera-based traffic sign recog-
nition
=> page 146
Cruise control system
> page 151,
=> page 152,
=> page 152
eit
Cruise control system
> page 151,
=> page 152,
=> page 152
Efficiency assist
> page 153,
Predictive control
=> page 158,
Adaptive cruise control
=> page 162,
Traffic jam assist
=> page 163
Adaptive cruise control
>page 158
Adaptive cruise control
=> page 162,
rae Traffic jam assist
=> page 162,
=> page 163
Distance warning
=> page 164
Active lane assist
=> page 165,
=> page 167
11

Instrument cluster
Belo
6/24/2019
6/24/2019
C100 T 0,0 mi
LOT SAF ela


Fig. 3 Instrument cluster overview (analog)


Depending on the vehicle equipment, the follow- — High-voltage battery charge level
ing items may appear in the instrument cluster: @) Right additional display with speed-
@® Left dial ometer
—Tachometer ........ 000.000 14 Left additional display with:
HSPOWERIMEER secur 2s essa oo awacnn @ 6 15 —'G@al a: = s qos os eee es eee er es 99
Tab
ara. « < sexes < + sgeps = ¢ eau 9 eee 13 — Audi drive select mode ......... 115
Central area ...............000. 13 Display
Status line (one or two lines) — Engine coolant temperature ~E .. 14
Right dial — High-voltage battery charge level

— Convenience display
— Speedometer

Display
—Fuellevel Y ............0.005 242
12

80B012721BA
Instrument cluster


ZA WARNING
Applies to: vehicles with Audi virtual cockpit
If there is a severe malfunction in the instru-
ment cluster, the display may turn off. The /\|
indicator light may also turn on. Stop the ve-
hicle safely. See an authorized Audi dealer or

authorized Audi Service Facility for assistance.

@) Tips
— The following pages primarily show illustra-
tions of the Audi virtual cockpit*. The dis-
play or location of the items that are shown
may vary on the different versions of the in-
strument cluster.
— You can select the units used for tempera-
ture, speed, and other measurements
> page 236.
— Speeds are displayed in mph (miles per
hour) or km/h (kilometers per hour).
— Certain instrument cluster content can also
be displayed in the head-up display*
=> page 26.
Operating
3:50™
12/5/2018

Fig. 4 Driver information system display



Fig. 5 Left side of multifunction steering wheel

Information is organized within various tabs @
in the instrument cluster. The tab contents are
displayed in the central area (2).
Requirement: the ignition must be switched on.
Selecting a tab
> Press the button @) repeatedly until the
desired tab is selected.
Returning to functions at higher levels
> Press the D button ©).
Opening and closing the menu
> Press the =] button ©.
Selecting and confirming a function
Requirement: a menu or list must be displayed.
> To select a function, turn the left thumbwheel
@ to the desired function.
> To confirm a selection, press the left thumb-
wheel (7).
Switching the view
> Press the VIEW button @) > page 13.
The following tabs may be available, depending
on vehicle equipment:




First tab Vehicle functions > page 16
Second tab | Driver messages (this is only dis-
played if at least one indicator
light/message is being displayed)
Third tab Radio > page 217
Media > page 227
Fourth tab | Telephone > page 190
Fifth tab Navigation > page 205
Adjusting the display


Applies to: Audi virtual cockpit
Fig. 6 Center display: adjusting the display
13

Instrument cluster

Switching the view
Applies to: Audi virtual cockpit
> Press the VIEW button to switch between the
default view @) and the enhanced view (2).
Adjusting the layout
Applies to: Audi virtual cockpit
Depending on the vehicle equipment, various lay-
outs may be available.
» Applies to: MMI: Select on the home screen:
SETTINGS > Display & brightness > Audi virtu-
al cockpit.
> To adjust the desired layout, press @).
Adjusting the additional display
Applies to: Audi virtual cockpit
Depending on the vehicle equipment, the addi-
tional displays that can be selected may vary.
> Applies to: MMI: Select on the home screen:
SETTINGS > Display & brightness > Audi virtu-
al cockpit > Configure.
> Select the desired additional display.
Reducing the display
Depending on the vehicle equipment, you can
hide the central area in the instrument cluster.
> Select on the instrument cluster: vehicle func-
tions tab > E=] button > Reduced display, or
> Press the VIEW button on the multifunction
steering wheel.
Coolant temperature
display
Applies to: vehicles with a coolant temperature indicator
The coolant temperature display @) > page 12
only functions when the ignition is switched on.
To reduce the risk of engine damage, please ob-
serve the following notes about the temperature
ranges.
Cold range
If only the LEDs at the bottom of the gauge turn
on, the engine has not reached operating tem-
perature yet. Avoid high engine speeds, full accel-
eration, and heavy engine loads.
14
Normal range
The engine has reached its operating tempera-
ture once the LEDs up to the center of the gauge
turn on. If the | indicator light in the instru-
ment cluster display turns on, the coolant tem-
perature is too high > page 253.
@) Note
— Auxiliary headlights and other accessories in
front of the air intake impair the cooling ef-
fect of the coolant. This increases the risk of
the engine overheating during high outside
temperatures and heavy engine load.
—The front spoiler also helps to distribute
cooling air correctly while driving. If the
spoiler is damaged, the cooling effect will
be impaired and the risk of the engine over-
heating will increase. See an authorized
Audi dealer or authorized Audi Service Fa-
cility for assistance.
Tachometer
The tachometer (@) 9 page 12 displays the engine
speed in revolutions per minute (RPM). The be-
ginning of the red zone in the tachometer indi-
cates the maximum permissible engine speed for
all gears once the engine has been broken in. Be-
fore reaching the red zone, you should shift into
the next higher gear, select the "D" or "S" selec-
tor lever position, or remove your foot from the
accelerator pedal.
Displaying the tachometer
Applies to: vehicles with plug-in hybrid drive
> Open the Vehicle functions tab.
> Applies to: vehicles with analog instrument
cluster: Select on the multifunction steering
wheel: [=] button > Tachometer.
> Applies to: vehicles with Audi virtual cockpit:
Select on the MMI home screen: SETTINGS >
Display & brightness > Audi virtual cockpit >
Left dial > Tachometer or Combined.
Engine speed limitation
If the BB indicator light turns on, the engine will
be automatically limited to the RPM displayed in
the instrument cluster. This will protect the >

80B012721BA
Instrument cluster

engine components, for example during a cold
start or from overheating.
The engine speed limitation is deactivated if you
release the accelerator pedal while the engine is
at normal operating temperature.
If the engine speed limitation was activated by
an engine control malfunction, the By indicator
light also turns on. Make sure the engine speed
does not go above the speed displayed, for exam-
ple when downshifting. Drive to an authorized
Audi dealer or authorized Audi Service Facility im-
mediately to have the malfunction corrected.
@) Note
The needle in the tachometer may only be in
the red area of the gauge for a short period of
time before there is a risk of damaging the
engine. The location where the red zone be-
gins varies depending on the engine.
Power meter
Applies to: vehicles with plug-in hybrid drive


© ©
@ Ip



RAZ-0575,

Applies to: vehicles with Audi virtual cockpit
Fig. 7 Instrument cluster: power meter

9 ©




[RAzZ-1117]

Applies to: vehicles with analog instrument cluster
Fig. 8 Instrument cluster: power meter
Displaying the power meter
Applies to: vehicles with Audi virtual cockpit
> Applies to: MMI: Select on the home screen:
SETTINGS > Display & brightness > Audi virtu-
al cockpit > Left dial > Power meter or Com-
bined.
The power meter (@) > page 12 gives feedback
about the usage capacity of the drive system. The
power meter needle displays the current usage
capacity.
Applies to: vehicles with Audi virtual cockpit: In
Audi virtual cockpit, a colored border indicates
how much the drive system can be currently uti-
lized. The colored borders may vary depending
the selected driving program and the electric
power currently available.
on
Depending on the vehicle equipment, the power
meter displays the following driving statuses:
@ Drive system switched off
@ Vehicle recovering electrical energy
@® Drive system switched on
@ Vehicle is driving with the electric
motor (green)
© Vehicle is driving with the electric
motor, the combustion engine can
switch on automatically (green
dash)
© Vehicle is driving with the combus-
tion engine (orange)
@ Vehicle is driving with maximum
power from the electric motor and
combustion engine for a brief peri-
od of time
Odometer


Fig. 9 Instrument cluster: reset button
15

Instrument cluster

The trip odometer and odometer are displayed in
the status bar @) > page 12.
The trip odometer shows the distance driven
since it was last reset. It can be used to measure
short distances. The odometer shows the total
distance that the vehicle has been driven.
Resetting the trip odometer
> To reset the trip odometer to zero, press the re-
set button @.
@) Tips
Distances are displayed in mi (miles) or km
(kilometers).
Outside temperature
display
The outside temperature is displayed in the sta-
tus bar @) > page 12.
If your vehicle is stationary or if you are driving at
very low speeds, the temperature displayed in
the instrument cluster may be slightly higher
than the actual temperature outside due to heat
radiating from the motor.
At temperatures below 41 °F (+5 °C), a snowflake
symbol appears in front of the temperature dis-
play > A.

Z\ WARNING
Do not assume the roads are free of ice based
on the outside temperature display. Be aware
that there may be ice on roads even when the
outside temperature is around 41 °F (+5 °C)
and that ice can increase the risk of accidents.

Engine oil temperature
indicator
Applies to: vehicles with engine oil temperature indicator
Depending on the vehicle equipment, the engine
oil temperature 7 may be indicated by a bar in
the instrument cluster.
» Applies to: vehicles with Audi virtual cockpit:
Open the vehicle functions tab and switch to
the enhanced view > page 13.
16
> Applies to: vehicles with analog instrument
cluster: Open the lap timer > page 148.
When engine oil temperatures are low, the dis-
play --- °F (--- °C) appears in the instrument clus-
ter. The engine has reached its operating temper-
ature when the engine oil temperature is be-
tween 176 °F (80 °C) and 248 °F (120 °C) under
normal driving conditions. The engine oil temper-
ature may be higher if there is heavy engine load
and high temperatures outside. This is not a
cause for concern as long as the E or = indica-
tor lights do not turn on.
Boost indicator
Applies to: vehicles with boost indicator
Depending on vehicle equipment, the current en-
gine load (meaning the current boost pressure)
may be indicated by a bar in the instrument clus-
ter.
> Applies to: vehicles with Audi virtual cockpit:
Open the vehicle functions tab and switch to
the enhanced view > page 13.
> Applies to: vehicles with analog instrument
cluster: Open the lap timer > page 148.
Vehicle functions
Overview
The trip computer is displayed in the first tab of
the driver information system. Additional vehicle
functions can be accessed depending on the vehi-
cle equipment.
> Press the [=] button on the multifunction steer-
ing wheel.
— On-board computer > page 17
— Energy flow > page 106
— Tachometer > page 14
—Lap times > page 148
— Lap statistics > page 148
— Reduced display > page 14

80B012721BA
Instrument cluster

On-board computer
Resetting values to zero
Requirement: the Consumption, Short-term
memory, or Long-term memory display must be
selected.
> To reset the values in the respective memory to
zero, press and hold the left thumbwheel on
the multifunction steering wheel for one sec-
ond.
Depending on the vehicle equipment, you can call
up the following displays in the on-board com-
puter one at a time by turning the left thumb-
wheel on the multifunction steering wheel:
— Time and date > page 236
— Level
— Digital speedometer
— Plug-in hybrid drive: range display
— Average consumption > page 17
— Range
— Short-term memory overview
— Long-term memory overview
— Energy consumers > page 17
— Driver assistance
— Traffic sign recognition and traffic light infor-
mation
Short-term memory and long-term memory
The short-term memory collects driving informa-
tion from the time the ignition is switched on un-
til it is switched off. If you continue driving within
two hours after switching the ignition off, the
new values will be included when calculating the
current trip information.
Unlike the short-term memory, the long-term
memory
is not erased automatically. You can se-
lect the time period for evaluating trip informa-
tion yourself.
Average consumption
The current consumption can be shown using a
bar graph. The average consumption stored in
the short-term memory is also displayed. If the
bar is green, your vehicle is saving fuel (for exam-
ple, using recuperation).
Energy consumers
The Energy consumers view lists other equip-
ment that is currently affecting fuel consump-
tion. The display shows up to three equipment
items. The equipment using the most power is
listed first. If more than three items using power
are switched on, the equipment that is currently
using the most power is displayed. A gauge also
shows the current total consumption of all other
equipment.
@) Tips
The date, time of day, and time and date for-
mat can be set > page 236.
17

Touch display

Touch displa > Press and hold an item until the associated op-
tions are displayed.
General touch display
operation Teen LCR ite
Applies to: touch display
Applies to: touch display
The center display is a touchscreen. Operation is
very similar to operating a smartphone.
@) Tips
Certain gestures are not available in every
menu.

Fig. 12 Touch display: pressing and pulling

>)
Applies to: touch display : Moving an item
You can position some items at any location on
the screen.
>» Press and hold an item, and then use your fin-
ger to pull it to the desired location.

inching fingers together and ling a
Applies to: touch display

Fig. 10 Touch display: pressing
Selecting a function or button
> Press the desired function or button.

Applies to: touch dis play

Fig. 13 Touch display: pinching fingers together and pull-
ing them apart
Zooming in and out on an item
> To increase the size of an item, touch it with
two fingers and pull your fingers apart.
> To decrease the size of an item, touch it with
two fingers and pull your fingers together.

Fig. 11 Touch display: pressing and holding
Accessing options
For some items, you can access additional op-
tions that are not directly visible.
18