ECO mode AUDI Q7 2013 Owner´s Manual

198 Airbag system
(D Tips
If the weight-sensing mat in the front pas­
senger seat detects an empty seat, the
front airbag on the passenger side will be turned off, and the
PASSENGER AIR BAG
OFF
light will stay on.
Repair, care and disposal of the airbags
Parts of the airbag system are installed at
many different places on your Audi . Installing,
removing, servicing or repairing a part in an
area of the vehicle can damage a part of an
airbag system and prevent that system from
working p roperly in a collision.
There are some important things you have to know to make sure that the effectiveness of
the system will not be impaired and that dis­
carded components do not cause injury or pol­
lute the environment.
A WARNING
Improper care, servicing and repair proce­
dures can increase the risk of personal in­
jury and death by preventing an airbag from deploying when needed or deploying
an airbag unexpectedly:
- Never cover, obstruct, or change the steering wheel horn pad or airbag cover
or the instrument panel or modify them
in any way .
- Never attach any objects such as cu­
pholders or telephone mountings to the
surfaces covering the airbag units.
- For cleaning the horn pad or instrument
panel, use only a soft, dry cloth or one
moistened with plain water. Solvents or
cleaners could damage the airbag cover
or change the stiffness or strength of the material so that the airbag cannot de­
ploy and protect properly.
- Never repair , adjust, or change any parts
of the airbag system.
- All work on the steering wheel, instru­
ment panel, front seats or electrical sys­
tem (including the installation of audio
equipment, cellular telephones and CB radios, etc.) must be performed by a
qualified technician who has the training
and special equipment necessary.
- For any work on the airbag system, we
strongly recommend that you see your
authorized Audi dealer or qualified work­
shop.
- Never modify the front bumper or parts
of the vehicle body.
- Always make sure that the side airbag
can inflate without interference:
- Never install seat covers or replace­
ment upholstery over the front seat­
backs that have not been specifically
approved by Audi.
- Never use additional seat cushions that
cover the areas where the side airbags
inflate.
- Damage to the original seat covers or
to the seam in the area of the side air­
bag module must always be repaired
immediately by an authorized Audi
dealer. - The airbag system can be activated only
once. After an airbag has inflated, it
must be replaced by an authorized Audi
dealer or qualified technician who has
the technical information, training and
special equipment necessary.
- The airbag system can be deployed only once . After an airbag has been deployed,
it must be replaced with new replace­
ment parts designed and approved espe­
cially for your Audi model version . Re­
placement of complete airbag systems
or airbag components must be per­
formed by qualified workshops only. Make sure that any airbag service action
is entered in your Audi Warranty
& Main­
tenance booklet under
AIRBAG REPLACE­
MENT RECORD .
-For safety reasons in severe accidents,
the alternator and starter are separated
from the vehicle battery with a pyrotech­
nic circuit interrupter.
- Work on the pyrotechnic circuit inter­
rupter must only be performed by a
qualified dealer - risk of an accident!

seat. The weight of a child restraint and its
"footprint" vary for different kinds of child re­
straints and for the different models of the
same kind of child restraint offered by child restra int manufacturers.
The weight ranges for the individual types, makes and mode ls of ch ild restra ints that the
NHTSA has specified in the Safety Standard
together with the we ight ranges of typical in­
fants and typical 1 year -old child have been
stored in the control unit of the Advanced A ir­
bag System . When a chi ld restraint is being
used on the front passenge r seat with a typi­
cal 1 year -old ch ild, the Advanced Airbag Sys­
tem compares the we ight measured by the
weight sensing mat with the information stor­
ed in the electronic control unit.
The electron ic contro l unit al so registers the
tension on the front passenger safety be lt.
The tension on the safety be lt for the front
passenger seat will be different for an adult
who is properly using the safety belt as com­
pared to the tension on the be lt when it is
used to attach a child restraint to the seat.
T he sensor below the latch for the safety belt
for the front seat passenger measures the
tension on the belt . T he input from this sen­
sor is t hen used w ith the we ight to "decide",
whether there is a ch ild restraint with a typ ica l
1 year-o ld child on the front passenger seat
and whether or not the airbag must be turned
off .
Child restraints and Advanced Airbags
Regard less of the child restraint that you use,
make sure that it has been certified to meet
United States Federal Motor Vehicle Safety
Standards and has been certified by its manu­
facturer for use with an airbag . Always be sure
that the chi ld restraint is p roperly instal led at
one of the rear seat ing pos itions . If in excep­
tional ci rcumstances you must use it on the
front passenger seat, carefu lly read all of the
information on child safety and Advanced Air­
bags and heed a ll of the app licable WARN­
INGS. Make certain that the child restraint is
correctly recognized by the weight-sensing
Child Sa fet y 207
mat inside the front passenger seat, that the
front passenger airbag is turned off and that
the a irbag status is always correct ly signaled
by the
PAS SENGE R AIR BAG OFF light.
Many types and models of child restraints
have been available over t he years, new mod­
els are introduced regu larly incorporating new
and improved des igns and o lder models are
taken out of product ion. Ch ild restraints are
not standard ized . Child restraints of the same
type typ ically have d ifferent weights and sizes
and different 'footpr ints,' the size and shape
of the bottom of the ch ild restrai nt that sits
o n the seat, when they a re insta lled on a veh i­
cle seat. These diffe rences make it v irtually
impossible to certify compliance with the re­
quirements for advanced airbags with each
and every ch ild restraint that has ever been
sold in the past or will be sold over the course
of the useful life of your veh icle.
For this reason, the United States National
Highway Traffic Safety Adm inistrat ion has
published a list of spec ific type, makes and
models of child restraints that must be used
to certify comp liance of the Advanced Airbag
System in your veh icle with the suppression
requirements of Federal Motor Vehicle Safety
Standa rd 208. These chi ld restraints are :
Subpart A - Car bed child restraints
Model
Angel Guard Angel Ride AA 2403FOF
Manufactured on or
after
September 25, 2007
Subpart B - Rear-facing child restraints
Model Manufactured on or
after
Century SmartF it December 1, 1999
4543
Cosco Arriva September 25, 2007
22-013PAW and base
22-999WHO
Evenf lo Discovery Ad- December 1, 1999
just Right 212
I
j
•
•
....

226 Intellig ent technol ogy
The vehicle is then stabilized by the forces act­
ing on the whee l during braking. If the vehicle
is
oversteering (rear tends to sk id out of the
turn), the brakes are ma inly applied on the
wheel that is on the outside of the curve. In
the case of a vehicle that is
understeering
(tendency to slide out of the curve), the
brakes are applied as needed on the whee l
that is on the ins ide of the curve or addit ional­
l y on the o ther wheels. An acoustic s ignal indi­
cates when ESC b rake app lication cuts in
¢ A .
The system operates across the entire speed
range in combination with the ABS system
¢ page 229. If the Anti-Lock Brake System
(ABS) malfunctions, the ESC wi ll be out of ac­
tion as well .
Activating
When you turn on the engine, ESC w ill auto­
mat ica lly be act ivated and will perform a se lf­
test. As soon as the test is comp leted, the sys­
tem is in normal operating mode.
Offroad mod e
ESC should normally be ope rated in normal
mode because this ensures maximum vehicle
stability. If necessary, you can act ivate the
ESC offroad mode by pressing the but to n
¢ fig . 232 to obtain maximum traction and
braking ability when driving
off paved roads at
l ow speeds. In ESC offroad mode, the indica­
tor light
Ii) ill uminates and the message Sta ­
b ilization control (E S C): Offr oad . Wa rning !
R estric te d stabilit y
appears br iefly in the dis­
p lay .
The ESC offroad mode can be useful in the fo l­
low ing except ional situations when slip or a
h ighly effective differential locking function is
des irable . Examp les:
- when driving with tire chains,
- when driving in deep snow or on loose
ground,
- when driving on uneven surfaces with the
whee ls severe ly unloaded (articulation), and
- when rocking the vehicle loose after it has
become stuck . When the
unusual situation is past, you
sho uld shift back to the norma l ESC operating
mode by pushing the button again . The mes­
sage
S ta b ilizat ion cont rol (ES C): O n then ap­
pears briefly in the display.
H ill desc ent control
The hill descent control is switched on in ESC
offroad mode . When slowly descending steep
gradients on loose ground or when the axles
are articulated, hill descent control provides ass istance by automatically apply ing the
brakes to keep vehicle speed constant. The ve ­
hicle is also rendered easier to steer by selec­
t ive d istr ibut ion of braking force. Hill descent
control intervenes when:
- the acce lerator pedal is not pressed,
- the vehicle is travelling less than 12 mph
(20 km/h),
- a steep gradient is detected,
- wheel behavior indicates loose ground or
conditions with poor adhesion (e .g. also axle
art iculation).
Hill descent contro l operates both d riving for­
ward and in reverse. Active hill descent con­
tro l is deactivated by pressing the accelerator
pedal until the condit ions for activation al­
ready listed are met again .
A WARNING
--
- The Electronic Stabilization Contro l is
neverthe less s ubject to the laws of phys­
ics. It is part icularly important to pay at­
tention to this fact on wet and slippe ry
roads . It i s therefore important that you
always adapt your dr iving to the cond i­
tion of the road and traffic conditions . Do
not a llow the increased safety provided
by the E lectronic Stabilization Contro l
system to lull you into accepting addi­
tional safety risks .
- Please be aware that in ESC offroad
mode, particularly on a smooth and s lip­
pe ry road, the wheels may have an in­
creased tendency to sp in and the vehicle
may b reak away - dange r of skidding!
~

236 Driving and en vir onm ent
- Do not a pply an under body p rotec tant in
the exhaust system area or a fire co uld
start.
Avoid damaging the
vehicle
When you are driving on poor roads, or over
curbs, steep ramps, etc., make certain that l ow-lying pa rts such as spoi lers and exhaust
system parts do not bo ttom out and get dam­
aged.
This is especially true fo r vehicles with low­
slung chassis (sports chassis)* and fully load­
ed ve hicles .
Operate your vehicle
economically and
minimize pollution
General
Your personal style of driving will determine
the economy of your vehicle, as well as ex­
haust and noise levels.
F ue l economy, envi ronmental impact, and
wear on you r engine, br akes and t ires large ly
depend on th ree factors:
- you r persona l dr iv ing sty le
- operating conditions
- technical lim itations
I f you anticipate what you need to do next and
d rive economically, you can easi ly cut your
fuel consumption by 10 -15 percent. This sec­
tion will give you some t ips on how you can
he lp the environment and your pocketbook .
(D Tips
The consumption estimates as published
by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the road, wh ich will vary depe nding upon vehi­
cle load and speed, road and weather con­
ditions, tr ip length, etc.
Drive smoothly and keep a lookout
ahead
Vehicles use the most fuel when they are ac­
celerating.
.,. Avo id u nnecessary accelerating and bra king.
Vehicles use the most fuel when they are ac­ ce lerat ing . If you ant icipate what is going to
happen next, you will need to brake less and,
thus, acce le rate less. Let the vehicle coast
whenever possible - for examp le when you see
t h at the next t raff ic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and
improves your mileage.
.,. Try and keep well below your car 's maxi -
mum speed .
Acce lerat ing gently reduces fue l cons ump­
t ion, eng ine wear, and does not disturb the
environment.
Fuel consumpt ion, exhaust emissions and e n­
gine noise increase disproportionately at high
speeds. If you drive at approximately three
quarte rs of top speed, fuel consumption w ill
be reduced by one ha lf. Never drive faster
t h an the pos ted speed limit and weathe r con ­
di tions pe rm it.
Reducing unnecessary idling
E ven when your car is just idling it burns up
fuel.
.,. Shut the eng ine off when you are not d riv­
ing the v ehicl e .
.,. Do not wa rm up t he veh icle by le tti ng the
eng ine run a t idle.
It makes sense to shut off the engine in traffic
jams, when wa it ing fo r tra ins to pass at rail­
road c rossings, o r at traffi c lights that have
l ong wai ts on red. T urning the eng ine
off f or
just 30 -40 seconds saves more f uel than is
burned start ing t he engine again .
IJII>

238 Driving off road
Driving off road
Driving in difficult road
conditions and offroad
General information
The operation of the E lectronic Stabilization
Control (ESC) is expanded for operation away
from paved roads. In situations where slip or a
differential locking function is required, the ESC offroad mode can be activated
c::> page 225 . Hill descent control is also availa­
ble in the ESC offroad mode, which automati­
cally brakes the vehicle and thereby keeps
speed constant when diffe rent wheel speeds
a re detected when descending a hill
c::> page 226. Your Audi also has permanent
a ll-wheel drive in addition.
H owever, your Aud i is not a pure off road vehi­
cle .
It was not built for d riving unde r extreme
conditions, e.g. fo r trips that are in the nature
of an expedition.
Dri ve only on road s and offroad section s
which mat ch the de sig n of your vehi cle and
y our a biliti es as a driver. Ne ver t ake ris k s!
Before driving offroad
- Check the eng ine oil level, tire pressure,
coolant level , and the fluid level in the w ind­
shield washe r reservo ir.
- Stow luggage items and other objects in the
luggage compartment, and secure them
against s lid ing aro und .
After driving offro ad
- After trips offroad, remove any twigs and
other foreign objects from the grill, the un­derbody and the wheels. Pay spec ia l atten­
t ion to fore ign objects (stones) which have
become lodged in the tire tread.
- Clean the body and the veh icle unders ide,
and inspec t the veh icle for poss ible damage.
- Clean dirty w indows , headlamp lenses , rear
l ights, and license plates .
- Perform a brake check (part icularly after
t ravel ling through water) .
A WARNING
-Drive especially attentively and plan
ahead in d iff icu lt road conditions and
when offroad. Excessive speed o r inco r­
rect maneuvers can cause injuries and
damage to the vehicle.
-
- Always adapt your speed and driving
style to road, offroad, t raff ic, and weath­
er cond itions. Drive especially slowly off­
road when you r view is res tricted.
- Please be awa re that in ESC off road
mode, particularly on a smoo th and s lip­
pery road, the wheels may have an in­
creased tendency to spin and the vehicle may break away -danger of skidding!
- Stability is limited in the ESC off road
mode .
@) For the sake of the environment
Avoid damage to the environment and re­
spect nature .
(D Tips
Only drive w here it is permitted and stay
on marked roads and paths.
Explanation of some technical terms
T he following data refe r to ideal cond itions.
Depend ing on veh icle load and ground condi ­
tions and the environment, the numbers may
vary. It is the driver's responsibility to decide
whether a vehicle can overcome a specific s it­
uat ion
c::> ,&. .
Gradient angle
The number of meters in alt itude gained over
a distance of 109.4 yards or 100 meters
(grade) are given as a percentage or degrees.
Information about the gradient the vehicle
can climb under its own power (depends in
part on the road surface and engine power) .
Max imum perm itted grade : 3 1
°
Late ral angle (slope of vehicle )
Indicates the angle up to which the vehicle
can be driven diagonally or across the fall line ..,.

Trailer towing Driving with a trailer
General information
Your Audi was designed primarily for passen­
ger transportation .
If you plan to tow a trailer, please remember
that the additional load will affect durability,
economy and performance .
Trailer towing not only places more stress on
the vehicle, it also calls for more concentra­
tion from the driver.
For this reason, always follow the operating
and driving instructions provided and use
common sense.
(D Note
If you are going to tow a trailer, you must
activate the trailer operation mode
q page 159, Towing a trailer.
Technical requirements
Trailer hitch
Use a weight-carrying hitch conforming to the
gross trailer weight. The hitch must be suita­ ble for your vehicle and trailer and must be
mounted securely on the vehicle's chassis at a
technically sound location. Use only a trailer
hitch with a removable ball mount. Always
check with the trailer hitch manufacturer to
make sure that you are using the correct
hitch.
Do not use a bumper hitch.
The hitch must be installed in such a way that
it does not interfere with the impact-absorb­
ing bumper system. No modifications should
be made to the vehicle exhaust and brake sys­
tems . From time to time, check that all hitch
mounting bolts remain securely fastened.
When you are not towing a trailer, remove the
trailer hitch ball mount. This prevents the
hitch from causing damage should your vehi­
cle be struck from behind~.&.
Trailer towing 241
Trailer brakes
If your trailer is equipped with a braking sys­
tem, check to be sure that it conforms to all
regulations.
The trailer hydraulic brake system must not be
directly connected to the vehicle's hydraulic
brake system
q .& .
Safety chains
Always use safety chains between your vehicle
and the trailer.
Trailer lights
Trailer lights must meet all regulations. Be
sure to check with your authorized Audi dealer
for correct wiring, switches, and relays.
Mirrors
If you are unable to see the traffic behind you
using the regular outside mirrors, then you
must install extended mirrors.
It is important
that you always have clear vision to the rear.
_&. WARNING
-If a trailer has electrical brakes please
note that these brakes are not activated
by the factory-fitted control unit -risk of
accident!
- After removing the trailer hitch, do not
store it in your vehicle. In case of sudden
braking, the hitch could fly forward and
injure you or your passengers.
- Never install a "weight distributing" or
"load equalizing" trailer hitch on your ve­
hicle. The vehicle was not designed for
these kinds of trailer hitches. The hitch
attachment can fail, causing the trailer
to tear loose from the vehicle.
- The Gross Vehicle Weight Rating for your
vehicle, found on the safety compliance
label on the driver's side B-pillar, must
never be exceeded under any circumstan­
ces. Exceeding the Gross Vehicle Weight
Rating of your vehicle is likely to damage
your vehicle, and such damage will not
be covered by your Limited New Vehicle
-
Warranty. Exceeding the Gross Vehicle ~
•
•

chains, make sure they will not drag on the
road when you are driving.
The cha ins shou ld cross under the trai le r
tongue to prevent it from dropping in case of
separation from the hitch.
(D Note
If you are going to tow a trailer, you must
activate the trailer operation mode
¢page 159, Towing a trailer.
Driving instructions
Driving with a trailer always requires extra
core and consideration.
To obtain the best poss ible handling of vehicle
and traile r, p lease note the following:
.,. Do not tow a loaded tra iler whe n your car it­
self is not loaded.
.,. Be especially careful when passing other
vehicles .
.. Observe speed limits.
.. Do not d rive at the maximum permissible
speed.
.. Always apply brakes early.
.. Monitor the temperature gauge.
Weight distribution
Tow ing a loaded trai ler with an empty ca r re­
sults in a high ly unstable distribution of
weight. If this cannot be avoided, drive at very
l ow speeds only to avoid the risk of losing
steering control.
A "balanced" rig is easier to operate and con ­
trol. This means that the tow vehicle should
be loaded to the extent possible and permiss i­
ble, while keeping the trailer as light as possi­
ble under the circumstances. Whenever possi­
ble, transfer some cargo to the luggage com­
partment of the tow vehicle wh ile observing
tongue load requirements and vehicle loading
considerations .
Speed
The higher the speed, the more difficult it be­
comes for the driver to control the rig . Do not
drive at the maximum permissible speed. Re-
Trailer towing 243
duce your speed even more if load, weather or
wind conditions are unfavorable - particularly
when going downhill.
Red uce veh icle speed
immediately if the trail­
er shows the slightest sign of sway ing.
Do not
try to stop the swaying by accelerating.
Observe speed limits. In some areas, speeds
f or vehicles towing trailers are lower than for
regular vehicles.
Always apply brakes early. When driving
downh ill, shift into a lowe r gear to use the en­
gine braking effect to slow the vehicle. Use of
the brakes alone can cause them to overheat
and fail.
Coolant temperature
The coolant temperature gauge¢ page 10
must be observed carefully. If the need le
moves close to the upper end of the scale, re­
duce speed immediately and/or turn off the
air conditioner.
If the coolant temperature warning light in
the instrument cluster starts flashing ., pull
off the road, stop and let the engine
idle for
about two minutes to prevent heat build -up .
A WARNING
Anyone not properly restrained in a mov­
ing vehicle is at a much greater risk in an
accident. Never let anyone ride in your car
who is not properly wearing the restraints
prov ided by Audi .
Trailer towing tips
Important to know
-
Your vehicle handles differently when towing
a trai ler because of the additional weight and
different weight distr ibution. Safety, perform­
ance and economy will great ly depend on how
carefully you load your trailer and operate
your rig.
Before you actua lly tow your tra iler, practice
turning, stopping and backing up in an area
away from traffic. Keep practicing until you
•
•

a reason to change the oil more often than recommended.
A WARNING
Stop! Before working in the engine com­
partme nt, always read and heed all WARN­
INGS
q & in Working in the engine com­
partment on page 264.
The engine com­
partme nt of any motor veh icle is a poten­
tially dangerous a rea and can cause ser i­
ous pe rsonal injury.
A WARNING
If you must change the engine o il i n your
vehicle:
- Always wea r eye p rotection.
- To reduce the r isk of burns from hot en-
gine oil let the engine cool down to the
t ouch.
- When removing the oil drain plug with
yo ur finge rs, stay as far away as possible.
Always kee p your forea rm pa ra llel to the
ground to he lp prevent ho t oi l from r un­
ning down your arm.
- Drain the o il into a co nt ainer designed
f or this p urpose, one large enough to
hold at least the total amount of oil in
yo ur engine .
- T o reduce the r is k of po ison ing, never use
empty food or beverage containers that
might mis lead someone into drinking
from them.
- Engine oil is poisono us. Keep it well out
of the reach of chi ldren.
- Cont in u ous contact with used engi ne oil
is harmful to your skin. Always protect
yo ur sk in by washing tho ro ughly with
soap and water.
(D Note
Never mix oi l addit ives with your engine
oil. These additives can damage your en ­
gine and adverse ly affect your Audi Limit­
ed New Vehicle Warranty.
-
Checkin g and fillin g 2 71
@) For the sake of the environment
-Before changing the oil, first make sure
you know where you can prope rly dispose
of the old o il.
- Always dispose of used oil p ro perly. Nev­
er dump it on garden soil, in wooded
areas, into streams or down sewage
dra ins.
- Recycle used o il by tak ing it to a used en ­
gine oil collection facility in your area, or
contact a service station.
- We strongly recommend that yo u have
your oil cha nged by an authorized Audi
dealer or a qualified wo rkshop with the
special tools a nd expert ise required, and
proper m eans of disposa l.
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro­ tects the engine from freezing in the winter.
T he cooling sys tem is sealed and genera lly re­
quires little attention.
T he cooli ng system has bee n filled a t the fac­
t ory with a permanent coolant which does not
need to be c hanged . The coo lant cons ists of a
mixture of water and the manufacturer's gly ­
col-based coo lant additive G l3 antifreeze
with anticorrosion additives (50% for USA
models; 60% for Canadian mode ls). This m ix­
ture both assures the necessary frost protec­
tion and protects meta l compone nts in t he
engine's cool ing system from corros io n and
sca ling.
It also raises the boiling point of the
c oolant.
Do not reduce the concentration of the cool ­
ant in the s ummer by adding p lai n water .
The
proportion of coolant additive must be at
lea st 50 % but not more than 60 %
to main ­
tai n antifree ze pro te ct io n a nd coo ling eff icien­
cy .
If the coo lant fros t protection is too low,
the coo lant co uld freeze and damage the vehi-
cle heating and engine cooling system. .,..
•
•

274 Che cking and filling
-If you drain the coolant, it must be
caught and safely stored in a proper con­
tainer clearly marked "poison".
(D Note
- Coolant pollutes the environment and
could cause an engine fire . Excess coo l-
ant will be forced out through the pres­
sure relief valve in the cap when the en­
gine becomes hot.
- If, in an emergency, only water can be
added, the correct ratio between water
and antifreeze
c:;, page 271 must be re­
stored as soon as possible .
@ For the sake of the environment
Dra ined coolant should not be reused. Al­
ways dispose of used coolant while observ­ ing all environmental regulations.
Radiator fan
The radiator fan switches on automatically by
itself
The radiator fan is driven by the engine via the
V-belt . The viscous clutch regulates the speed
of the fan accord ing to t he temperature of the
coolant.
An auxiliary electric radiator fan* switches on
and off depending on coolant temperature
and other vehicle operating conditions.
After you switch the engine off, the auxiliary
fan can continue running for up to 10 minutes - even with the ignition off. It can even switch
on again later by itself
c:;, &. , if
- the temperature of the engine coolant rises
due to the heat build-up from the engine in
the engine compartment, or
- the engine compartment heats up because
the vehicle is parked in intense sunlight.
_&. WARNING
- To reduce the risk of personal injury nev­
er touch the radiator fan . -
The auxiliary electric fan is temperature
controlled and can switch on suddenly
even when the engine is not running.
- The auxiliary radiator fan switches on au­
tomatically when the engine coolant
reaches a certain temperature and will
continue to run until the coolant temper­
ature drops.
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance.
Fig. 248 Eng ine compart men t: cover on the brake fluid
reservoir
Before you check anyth ing in the engine com­
partment,
always read and heed all WARN­
INGS c:;, _&. in Working in the engine compart­
ment on page 264.
.,. Read the brake fluid level from the brake
fluid reservoir
c::> fig. 248, c:;, page 266,
fig. 243.
The brake fluid level m ust be be­
tween the "MIN" and "MAX" markings.
The brake fluid reservoir is located at the rear
part ition of the engine compartment on the
left side
c:;, page 266.
The fluid level may drop slightly after some
time due to the automatic adjustment of the brake pads. This is not cause for alarm .
If the brake flu id level falls
considerably be­
low the
"MIN" mark, the brake warn ing/indi­
cator light ( U.S. models:
1111 , Canadian
models :. will come on
c::> page 19 and
c::>page 32. Do not continue to operate the ve-
hicle. The complete brake system should be ..,.

Tires an d wheel s 285
change. In the event of discrepancies, the tire
pressure label located on the driver's side 8-
p ill ar a lways takes precedence.
The table be low lists the recommended cold
tire inf lation pressures for the A udi model
I Model / Tire designation
covered by your Owner's Literature at the vehi­
cle's capacity weight and the tire sizes instal­
l ed on the respect ive models as orig inal
equipment, or as a factory option.
Tire pressure
Engine normal load condition full load condition
front rear front rear
I
PSI II kPA PSI kPA PSI j[ kPA PSI kPA
Q7:
3.0 liter
6-cy linder 2
55/5 5 Rl8 109H XL
All Sea son
265 /50 Rl9 ll0H XL
All Sea son
2 75/45 R20 ll0H XL
All S ea so n
275 /45 R20 110V XL
High Performance
295 /35 R21 10 7V XL
High Performance
35 240 35
35 240 35
35 240 35
35 240 35
36 250 35 240
44
300 49 340
240 44 300 49 340
240 44 300 49 340
•
240 44 300 49 340
I
240 44 300 49 340
XL= reinforced or extra load tire. It may als o appear as xl, EXTRA LOAD, or RF on the tire side­
wall.
The correct tire pressure for the spare wheel i s
l ocated on a label on the driver's side 8-pilla r.
Because technical changes may be made to
vehicle equ ipment during the model year, al­
ways compare the tire size designation on the
tire pressure label on your vehicle w ith the
tires on your vehicle. Ma ke sure that the tire
size information on the veh icle label is the
same as the s ize of the t ires on the vehicle.
This is especially important if the vehicle be­ l ongs to someone else or you bought the vehi­
cle with different rims/tires or you bought the
vehicle as a previously owned vehicle.
Remember, your safety and that of your pas­
sengers also depends on making sure that
l oad limits are not exceeded. Vehicle load in­
cludes everybody and everything in and on the
vehicle. These load limits are technically refer­ red to as the vehicle's Gross Vehicle We ight
Rating ("GVWR") . The Gross Axle Weight Rat­
i ng ("GAWR") is the maximum load that can
be appl ied at each of the veh icle's two axles.
The G ross Vehicle Weight Rating and the Gross Axle Weig
ht Rating are listed on the
safety compl iance sticker label located on the
drive r's side 8-pillar . The tire pressure labe l on
your A udi lists the maxim um combined
weight of all of the occ upants and luggage or
other cargo that t he vehicle can carry. Fo r the
location of the tire pressure label ¢
fig. 251.
A WARNING
Overloading a vehicle can cause loss of ve­
h icle control, a crash or other accident, se­
rious personal injury, and even death.
- Carrying more we ight than your veh icle
was des igned to carry will prevent the
veh icle from handling properly and in­
crease the risk of a loss of vehicle con­
trol.
- The brakes on a vehicle that has been overloaded may not be able to stop the
veh icle w ith in a safe distance.
- T ires on a vehicle that has been overload­
ed can fail suddenly caus ing loss of con-
trol and a crash. ..,.
•
•