belt AUDI Q7 2013 Owner´s Manual

-Children on the front seat of any car,
even with Advanced A irbags, can be seri­
ous ly injured or even killed when an a ir­
bag inflates.
- Never let a child stand or kneel on any
seat, for examp le the front seat.
- Never let a child ride in the cargo area of
your vehicle .
- Always remember that a ch ild lean ing
forward, sitt ing sideways or out of posi­
t ion in any way during an acc ident can be
struck by a deploying airbag . This will re­
sult in se rious personal injury or death .
- If you must install a booster seat on the
front passenger seat because of excep­
t ional circumstances the
PASSENGER
AIR BAG OFF
light must come on and
stay on, whenever the ignition is switch­
ed on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, perform
the checks described¢
page 195, Moni­
toring the Advanced Airbag System.
- Ta ke the child restrain t off the front pas­
senger seat and install it properly at one
of the rear seat positions if the
PASSEN­
GER AIR BAG OFF
light does not stay on
whenever the ignition is switched on.
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used¢
page 175, Safety
belts,¢ page 184, Airbag system
and
c:> page 205, Important things to know.
Installing a child safety
seat
Securing a child safety seat using a
safety belt
Safety belts for the rear sea ts and the fron t
passenger can be locked wi th the convertible
locking retractor to properly secure child
safety seats .
The safety belts emergency lock ing retractors
for the rear seats safety belts and for the
front passenger's seat safety belt have a con ­
ve rtible locking retractor for child restraints.
Child Sa fet y 215
The safety belt must be locked so that be lt
webbing cannot unree l. The retractor can be
activated to lock the safety belt and prevent
the safety belt webbing from loosening up
during normal dr iving . A child safety seat can
only be properly installed when the safety belt
i s locked so that the chi ld and child safety
seat w ill stay in place .
Always remember: Even though your vehicle is equipped with an Advanced Airbag system, all
ch ildren, especially those 12 years and young­
er, shou ld always r ide in the back seat proper­
ly restrai ned fo r the ir age and size.
A WARNING
Improperly installed chi ld safety seats in­
crease the risk of serious personal injury
and death in a collision.
- Always ma ke sure that the safety belt re­
tracto r is loc ked when installing a child
safety seat . An unlocked safety belt re­
tractor cannot hold the child safety seat
in place during normal dr iving or in a
crash.
- Always buckle the child safety seat firmly
in place even if a ch ild is not sitt ing in it.
A loose child safety seat can fly around during a sudden stop or in a collision .
- Always make sure that the rear seat
backrest to which the center rear safety
be lt is attached is securely latched when­
eve r the rea r center safety belt is being
used to secure a ch ild restra int.
- If the backrest is not securely latched,
the child and the child restraint will be
thrown forward together with the back­ rest and will strike parts of the vehicle
interior. The child can be seriously in­
jured or killed.
- Never install rear-fa cing child safety
seats or infant carrie rs on the front pas ­
senger seat . A child will be serio usly in­
jured and can be killed when the passen­ ger airbag inflates.
- The inflating airbag will h it the ch ild
safety seat or infant carrier with great
force and will smash the child safety seat
~
•
•

-A tight tether strap on a rearward-facing
child restraint attached to the front pas­
senger seat can put too much pressure on the weight-mat in the seat and regis­
ter a heavier weight in the Advanced Air­
bag System . The heavier weight regis­
tered can make the system work as
though an adult were on the seat and de­
ploy the Advanced Airbag when it must
be suppressed causing serious or even
fatal injury to the child .
- Make sure that the
PASSENGER AIR BAG
OFF
light comes on and stays on all the
time whenever the ignition is switched
on.
- If the
PASSENGER AIR BAG OFF light
does not come on and stay on, immedi­
ately install the rear-facing child safety
seat in a rear seating position and have
the airbag system inspected by your Audi dealer.
Activating the convertible locking
retractor
Use the convertible locking retractor to se­
cure a child restraint.
Always heed the child safety seat manufactur­
er's instructions when installing a child re­
straint in your vehicle . To activate the conver­
tible locking retractor :
.. Place the child restraint on a seat, prefera­
bly on the rear seat.
.. Slowly pull the belt
all the way out .
.. Route it around or through the child re ­
straint belt path~&_ .
.. Push the child safety seat down with your
full weight to get the safety belt really tight.
.. Insert the belt tongue into the buckle for
that seating position .
.. Guide the safety belt back into the retractor
until the belt lies flat and snug on the child
safety seat .
.. You should hear a "clicking " noise as the
belt winds back into the inertia reel. Test the
convertible locking retractor by pulling on
the belt . You should no longer be able to
Child Safety 21 7
pull the belt out of the retractor. The con­
vertible locking retractor is now activated.
.. Make sure that the red release button is fac­
ing away from the child restraint so that it
can be unbuckled quickly.
.. Pull on the belt to make sure the safety belt
is properly tight and fastened so that the
seat cannot move forward or sideways more
than one inch (2.5 cm).
_&. WARNING
Using the wrong child restraint or an im­
properly installed child restraint can cause
serious personal injury or death in a crash.
- Always make sure that the safety belt re-
tractor is locked when installing a child
safety seat. An unlocked safety belt re­
tractor cannot hold the child safety seat
in place during normal driving or in a
crash.
-Always buckle the child safety seat firmly in place even if a child is not sitting in it.
A loose child safety seat can fly around
during a sudden stop or in a crash.
- Always make sure the seat backrest to
which the child restraint is installed is in
an upright position and securely latched
into place and cannot fold forward . Oth­
erwise, the seatback with the child safety
seat attached to it could fly forward in
the event of an accident or other emer­
gency situation .
- Always read and heed all WARNINGS
whenever using a child restrained in ave­
hicle is being used¢
page 205. Special
precautions apply when installing a child
safety seat on the front passenger seat
¢ page 186, Child restraints on the front
seat -some important things to know .
-
•
•

218 Child Saf ety
Deactivating the convertible locking
retractor
The convertible locking retractor for child re­
straints will be deactivated automatically when the belt is wound all the way back into the retractor.
.,. Press the red button on the safety be lt
buck le. The belt tongue wi ll pop out of the
buck le .
.. Guide the safety belt all the way back into
its stowed position .
A lways le t the safety belt retract complete ly
into its stowed position . The safety belt can
now be used as an ordinary safety belt with ­
out the convertib le locking r etractor for chi ld
restra ints .
I f the convertible locking retractor shou ld be
activated inadvertently, the safety belt m ust
be unfastened and guided completely back in­
to its stowed pos ition to deactivate th is fea­
ture. If the convertible locking retractor is not
deactivated, the safety belt will gradually be­
come tighter and u ncomfortable to wear .
A WARNING
Improperly insta lled child safety seats in­
crease the risk of ser ious personal inju ry
and death in a collision .
- Never unfaste n the safety belt to deacti­
vate the convert ible lock ing ret ractor for
c hild rest rain ts while the veh icle is mov­
ing. You would not be restrained and
cou ld be seriously injured in an accident.
- Always read and heed all WARN INGS
whenever using a child restrained in ave ­
hicle is being used
c::> page 205. Special
precautions apply when installing a ch ild
safety seat on the front passenger seat
<=> page 186, Child restraints on the front
seat -some important things to know .
LATCH Lower
anchorages and tethers
for children
Child Restraint System anchors and how
are they related to child safety
To p rov ide a simpler and more practicable way
to a ttach the child restra int on the vehi cle
seat, Federal regulat ions req uire spec ia l lowe r
anchorages in vehicles and devices on new
child restraints to attach to the vehicle ancho­
rages.
T he combination of the tether anc horages and
the lowe r anchorages is now genera lly ca lled
t h e
LATCH system fo r "Lower Anchorages and
T ethers for Child ren."
F o rward-facing chi ld restrai nts ma nufactured
after September 1, 1999, are requ ired by U .S .
f edera l regu lations to comply with new child
head movement performance req uirements.
These new performance req uirements make a
tether necessary on most new child seats.
Installing a child restraint that requires a top
tether without one can seriously impair the performance of the c hild restra int and its abil­
ity to protect the child in a coll is ion. Insta lling
a chi ld restraint that requires a top tether
without the top tether may be a violat ion of
state law.
Child restraint manufacturers offer LATCH
lower anchorages on their child seats w ith
hook -on or push-on connectors attached to
adjustable straps .
In add ition to the LATCH lower anchorages,
these chi ld restraint systems usually require
the use of tether straps to he lp keep the chi ld
rest raint firmly in place.
A WARNING
-Imp roper installat ion of ch ild restra ints
will i ncrease the r is k of injury a nd death i n
a crash.
-

-Always follow the instructions provided
by the manufacturer of the ch ild re­
straint you intend to install in your veh i­
cle .
- Never install a child restraint without a
properly attached top tether strap if the
child restraint manufacturer's instruc­
t ions req uire the top tether strap to be
used.
- Improper use of ch ild restra int LATCH
lower anchorage points can lead to injury
in a collision. The LA TCH lower anchorage
points are designed to withstand only
those loads imposed by correctly fitted
child restraints.
- Never mount two child restraint systems
on one LATCH lower anchorage point.
- Never secure or attach any luggag e or
other item to the LATCH lower anchorag­
es .
{i) Tips
-In Canada, the terms "top tether" with
"lowe r universal anchorages" (or "lower
universal anchorage bars") are used to
desc ribe the system .
- In other countries, the term "ISOFIX" is
us ed to describe the lower anchorages.
Location
Fig . 222 Schematic overv iew : LATCH anc horage poi nt
locations
The illustration shows the seating locations in
your vehicle which are equipped with the low­ er anchorages system.
Child Safety 219
Description
The lower anchorage positions are marked
for quick locating .
Fig. 223 Second row of seats: lower anc horage b racket
locat io n s
Fig. 224 Thir d row of seats: locato r buttons for lower
a nch orages
Attachment locator markers for lower
anchorages
T he lower anchorage locations in the second
row of seats are indicated by the attachment
locator markers of the lower anchorage brack­
ets <=>
fig. 223. Remove the covers to access
the lower anchorage brackets . Circular locator
buttons on the third row of seats" indicate the
lower anchorage locations on the third row of
seats <=>
fig. 224 .
Lower anchorages
The lower anc horage attachment points are
located between the rear seatback and rear
seat cushion <=>
fig. 223 or<=> fig. 224.
Lower anchorages secure the child restraint in
the seat without using the vehicle's safety
belts. Anchorages provide a secure and easy­
to-use attachment and minimi ze the possibili-
ty of improper child restraint installation. .,..

220 Child Safe ty
A ll child restraints man ufactured after Sep­
tember 1, 2002, must have lower anchorage
attachments for the
LATCH system.
Remember that the lower anchorage points
are on ly intended for installation and attach­
ment of child restraints specifically certified
for use w ith
LATCH l ower anchorages . Child
restra ints that are not equipped with the tow­
er anchorage attachments can still be instal­ led in compliance with the ch ild restra int
manufacturer's instruct ions on using vehicle
safety belts.
A WARNING
Improper use of LATCH lower anchorages
can ca use serio us pe rsonal injury in an ac­
cident.
- Always carefully follow the ch ild re­
strain ts manufac turer's instruct io ns for
proper installation of the child restraint
and proper use of the lower anchorages
or safety belts in your vehicle .
- Never secure o r attach any l uggage or
ot her items to the
LATCH lower ancho­
rages.
- Always read and heed the important in­
formation about child restraints in this
chapter and WARNINGS
¢ page 205,
Child Safety.
Guidance fixtures for lower anchorages
Applies to vehicles: with third row seating
Special guidance fixtures increase the conven­
ience of the lower anchorages and are availa­
ble from your authorized Audi dealer.
Fig . 225 Thir d row of seats: install ing the gu idance fix ·
tures
0
Fig. 226 Close-up: fitting the guidance fixture over t he
l ower anchorage bracket
T he lower ancho rage attachment poi nts are
located on the third row of seats between the
seatback and the seat cushion. Special guid­
ance fixtures increase the conven ience of the
lower anchorages and help protect the seat
mater ial from possib le damage when instal­
ling ch ild restra ints .
Installing the guid anc e fixture s
.,. Push down on the seat cushion so that the
tower anchorages are v is ible.
.,. Hold the guidance fixture with the part
number facing downward and push it in the
d irection of the arrow onto the anchorage
¢fig. 226 .
.,. Make s ure that ea ch of the two guidance fix­
t ures per sea t snaps into place.
Removing the guidance fixtures
.,. Remove the ch ild restraint according the
child restraint manufacture r's instructions .
.,. Push down on the seat cus hion so that the
lowe r ancho rages are v is ible.
.,. Pull off the gu idance fixtures from the low ­
er ancho rages .
.,. Always remove the guidance fixtures and
keep them in a safe p lace when not in use .
You may find it easier to install c hild re­
straints equ ipped with hooks attached to
straps witho ut the g uidance fixtures in place.
If this is the case, remove the guidance fix­
tures by pulling them off the anchorages. However, the guidance fixtures can help you
to locate the
LATCH anchorages . ..,.

_& WARNING
Improper use of tether anchorages or low­
er anchorages can cause serious personal
injury in a crash.
- Always carefully follow the child re­
straint manufacturer's instructions for
proper installation and use of child re­
straint systems.
- Never use the
LATCH or tether anchorag­
es to attach safety belts or other kinds of
occupant restraints.
- Child restraint tether attachments and
lower attachments are only designed to
secure a child restraint that has been
equipped to use these anchorages.
- Tether anchorages and lower anchorages
are designed to withstand only those
loads imposed by correctly fitted child
restraints. Under no circumstances can
they be used safely for adult or child
safety belts or harnesses.
- Never mount more than one child re­
straint to a single tether or to a lower an­
chorage point. Attaching two child re­
straints to a single anchorage point can
cause the anchorage to fail and cause se­
rious personal injury in a crash.
(D Note
-Remove the guidance fixtures before
folding the rear seatback to prevent
damaging the seat cushion.
- If you leave the guidance fixtures instal­
led for several days, they could leave a
mark on the upholstery on the seat cush­
ion and backrest in the area that the
guidance fixtures were installed. The up­
holstery would also be permanently
stretched around the guidance fixtures.
This applies especially to leather seats.
Child Safety 221
Installing a child restra int with LATCH
lower anchorages
Whenever you install a child restraint always
follow the child restraint manufacturer's in­
structions.
Fig. 227 Lower anchorages: proper mounting
Mounting
.. Make sure the seatback of the rear seat
bench is in the upright position and securely
latched in place.
.. Attach both hook-on connectors with the
spring catch release on the child safety seat
onto the LATCH lower anchorage so that the
connectors lock into place
¢fig. 227.
.. Pull on the connector attachments to make
sure they are properly attached to the LATCH
lower anchorage .
.. Pull straps tight following the child re­
straint manufacturer's instructions.
Releasing
.. loosen the tension on the straps following
the child restraint manufacturer's instruc­
tions.
.. Depress the spring catches to release the
anchorage hooks from the lower anchorag­
es.
Remember: Use tether straps to help keep the
child restraint firmly in place.
A WARNING '-
Improper use of the LATCH system can in-
crease the risk of serious personal injury
and death in an accident.

222 Child Safe ty
- These anchors were developed only for
child safety seats us ing the ''LATCH" sys­
tem.
- Never attach other child safety seats,
belts or other objects to these anchors.
- Always make sure that you hear a click
when latching the seat in place. If you do
not hear a click the seat is not secure and
cou ld fly forward and hit the interior of
the vehicle, or be ejected from the vehi­ cle.
A WARNING
Improper insta llation of chi ld restraints
w ill increase the risk of injury in an acc i­
dent.
- Always fo llow the child restraint system
ma nufacturer's instructions for proper
installation of the child restraint system
and proper use of tether straps as we ll as
the lower anchorages or safety belts in
yo ur vehicle.
- Always read and heed the important in ­
format ion and WARNINGS about child
safety and the installation of child re­
straint systems ¢
page 205, Child Safe­
ty.
Tether anchors and tether straps
Fig. 228 Tether anchors for second row of seats: at­
t ac hm ent hook locatio ns
-
Fig. 229 Tet her anchors fo r thir d row of seats: attach­
men t hook loca tions
The tether anchors for the three rear seating
positions in the second row of seats are locat­
ed underneath the seats in the back
c> fig. 228. For vehicles with third row seat­
ing*, the tether anchors for the two seating
pos itions in the third row of seats are stored
u nderneath a p lastic cover cap in the floor
c> fig . 229 .
A tether is a stra ight or V-shaped strap that
attaches the top part of a ch ild restra int to
special anchorage po ints in the vehicle .
The purpose of the tether is to reduce the for­
ward movement of the child restraint in a
crash, in order to help reduce the risk of head
injury that could be caused by striking t he ve­
hicle inte rior .
Forward facing child restraints manufactured
after September 1, 1999, are required by U.S .
federa l regu lations to comply with new child
head movement perfo rmance requ irements .
T hese new perfo rma nce req uirements make a
tether nece ssary on most new child safety
seats .
,&_ WARNING
-= -Improper installation of child restraints
will increase the risk of injury and death i n
a crash.
- Always follow the instructions provided
by the manufacturer of the child re-
straint you intend to install in your Audi. ..,_

-Improper use of child restra int anchors
(incl uding tether anchors) can lead to in­
jury in a co llision. The anchors are de­
signed to withstand only those loads im­
posed by correctly fitted ch ild restraints .
- Never mount two child restraint systems
on one LATCH lower anchor po int.
- Never attach two child restraint systems
to one tether strap or tether anchorage.
- Never attach a tether strap to a tie-down
hook in the luggage compartment.
- Never use ch ild restra int tether ancho­
rages to secure safety belts or other
kinds of occupant restra ints.
- Never secure or attach any luggage or
other items to t he LATCH lower ancho­
rages or to the tether anchors.
- If a tether or other strap is used to at­
tac h a child restraint to the fro nt passen­
ger seat, make sure that it is not so
t ight, that it causes the we ight-sensing
mat to measu re mo re weight than is ac­
t ual ly on the seat.
- T he heav ier we ight reg iste red can make
the Advanced Airbag System wo rk as
though an adult were on the seat and de­ ploy the Adva nced Ai rbag when it must
be s uppressed causing serious or even
fatal injury to the child.
- If you must install a rearward facing
child safety seat on the front passenger
seat because of exceptional circ umstan ­
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im­
med iately install the rear-facing child
safety seat in a rear seating posi tion and
have the a irbag system inspected by you r
Audi dealer.
Child S afety 223
Installing the upper tether strap on the
anchorage
Fig . 230 Tet her st rap: prope r rout ing a nd mounti ng
Fi g. 23 1 Tet her st rap fo r seco nd row sea ts: prope r
rou ting and moun tin g
Installing the tether strap
... Release or deploy the tether strap on the
child res traint accord ing to the child re ­
st raint manufacture r's ins tructions .
... Guide the upper tether strap
und er the rear
head restraint and into the rear ca rgo area
(raise the head restraint if necessary).
... Fo r the second row o f seats: Pull the floor­
ing back, in order to reach the anchor brack­
et
c:::> fig. 231 .
... Fo r the third row of seat s:* Remove the
plastic cover cap with a screw drive r, in orde r
to reach the anchor bracket
c:::> page 222,
fig . 229.
.,. Slide the tether strap hoo k over the anchor
bracket .
... Pull on the tether strap hook so that the
spring catch of the hook engages .
.,. Tighten the tether strap firmly follow ing
the child restra int manufacturer's instruc­
tions .
.,. For the second r ow of s eats : Push the floor-
ing forward into place again.
11-

224 Child Saf ety
Re leas ing th e te th er str ap
.. Loosen the tension following the child re­
stra int manufacturer's instructions.
.. Depress the spring catch on the hook and
release it from the anchorage .
.. Fo r t he seco nd ro w of se ats: Push the floor­
ing forward into place again.
.. For the th ird r ow of seats :* Replace the
plast ic cover cap .
(D Note
If you leave the child restraint with the
tether strap firmly installed for several
days, this could leave a mark on the up­
holstery on the seat cushion and backrest
in the area whe re the tether strap was in­
stalled. The uphols tery would a lso be per­
manently stretched around the tether
strap . This applies especially to leather
seats .
Using tether straps on rearward-facing
child restraints
Currently , few rear -facing child restraint sys­
tems come with a tether . P lease read and
heed the child restraint system manufactur­
e r's instructions caref ully to determine how to
p roperly insta ll the tethe r.
& WARNING
A child in a rearward -facing child safety
seat insta lled on the front passenger seat
w ill be seriously injured and can be ki lled if
the front a irbag inflates - even with an Ad­
vanced Airbag System.
- The inflating airbag will hit the child safety seat or infant carrier with great
force and w ill smash the ch ild safety seat
and child against the backrest, center
armrest, or door .
- A tight tether or other strap on a rear­
ward-facing child restra int attached to
the front passenger seat can put too much pressure on the weight-mat in the
seat and register a heavier weigh t in the
Advanced Airbag System. The heav ier weight registered can make the system
work as though an adult were on the seat
and deploy the Advanced Airbag when it must be suppressed causing ser ious or
even fatal injury to the ch ild.
- If you must install a rearward fac ing
child safety seat on the front passenger
seat because of exceptional c ircumstan­
ces and the
PASSENGER AIR BAG OFF
light does not come on and stay on, im­
mediately insta ll the rear-fac ing ch ild
safety seat in a rear seating position and have the airbag system inspected by your
Audi dea ler.
Additional Information
Sources of information about child
restraints and their use
T here are a number of sou rces of add itiona l
information about child restraint se lection, in ­
sta llation and use:
N HT SA advises that the best chi ld safety seat
is the one that fits your ch ild and fits in you r
vehicle, and that yo u will use correct ly and
consistently.
T ry before yo u buy!
U. S Nat ional Highw ay Traffi c Safety Admin ­
i s trat ion
Tel.: 1-888-327-4 236 (TIY: 1-800-424-9153)
http://www.nhtsa.gov
N ati onal SAFE KID S Camp aign
Tel.: (202) 662-0600
http://www.safekids .o rg
S af ety Belt Saf e U. S.A
T el.: (800) 7 45 -SAFE (Eng Lish)
Tel.: (800) 747-SANO (Span ish)
http://www.ca rseat.org
T ranspo rt Ca nad a Info rmation Centre
Tel.: 1-800 -333-0371 or call
1-613-998-8616 if you are in the Ottawa area
http://www.tc.gc.ca/eng/ roadsafety/
menu.htm
Aud i Cu stom er R elation s
Tel.: (800) 822-2834

Intelligent technology Notice about data
recorded by vehicle
control modules
Your vehicle is not equipped with an Event Da­
ta Recorder (EDR), installed by some manu­
facturers for the express purpose of capturing
data for retrieval after an accident or crash
event. EDRs are sometimes called "crash re­
corders".
Some state laws restrict the retr ieval or down­
loading of data stored by EDRs that were in­
stalled in a vehicle for the express purpose of
retrieving data after an accident or crash
event without the owner's consent.
Although your vehicle is not equipped with an
EDR, it is equipped with a number of electron­
ic control modules for various vehicle systems
such as, for example, engine function, emis­
sion control, as well as for the airbags and
safety belts.
These electronic control modules also record
vehicle-related data during norma l vehicle op­
eration for diagnostic and repair purposes.
The recording capacity of the electronic con­
trol modules is limited to data (no sound is re­
corded) and only a small amount of data is ac­
tually recorded over a very limited period of
time and stored when a system fault or other
condition is sensed by a control unit. Some of
the data then stored may relate to vehicle
speed, direction, braking as we ll as restraint
system use and performance in the event of a
crash or other condition. Stored data can only be read and downloaded with special equip­
ment.
Intelligent technology 225
Electronic Stabilization
Control (ESC)
General information
The ESC improves the vehicle stability.
. ..---------..
------- -
Fig. 232 Center console with ESC sw itch
ESC is designed to help you maintain vehicle
control in situations where the car approaches
the limits of "grip", especially when accelerat­
ing and cornering. ESC reduces the risk of
skidding and improves stability under all road
condit ions .
The system operates across the entire speed range in combination with the ABS system. If
the Anti-Lock Brake System (ABS) malfunc­
tions, the ESC will also shut down.
How the system works
The Anti-Lock Brake System (ABS), Electronic
Differential Lock (EDL) and the Anti-Slip Regu­
lation System (ASR) are integrated in the Elec­
tronic Stabilization Control. In addition to the
data prov ided by these functions, the ESC con­
trol unit requires additional measurement da­
ta provided by high performance sensors. The
rotational speed of the vehicle about its verti­
cal axis, vehicle acceleration in the fore-and­
aft and lateral directions, the brake pressure and the steering angle are all measured.
T he direction in wh ich the driver wishes to
travel is determined with the aid of the steer­
ing angle and vehicle speed and is continually
compared with the actual behavior of the ve­
hicle. If the two do not match, for example,
when the vehicle starts hydroplaning on a wet
road, ESC will automatically brake the appro-
priate wheel to correct the problem. ..,_
•
•