wiper blades AUDI Q7 2013 Owner´s Manual

64 Clear vis ion
General information
The winds hield wipers and the w indshield
washer system operate only with the ignition
on.
During a temporary stop , e.g . at a t raff ic sig­
na l, the set wipe speed is automatically re­
duced by one stage.
The winds hield washer no zzles a re heated at
l ow temperatures when the ignition is on .
Removing w ate r droplet s
About 5 seconds after the wash cycle is com­
plete, the wiper system performs a single au ­
tomatic wipe cycle to remove any water drop­
l ets that remain on the windshield whi le dr iv ­
ing.
If you would like to deactivate this delayed
wipe cycle wh ile driving, you have to pull the
l eve r to pos ition ® again within 10 seconds
after this wipe cy cle.
Water droplet removal is reactivated after the
ignit ion is switched off and then on again .
Winter position
To speed up de -icing of the w indshield w ipers,
t hey move to the winter posi tion when the ig­
n ition is switched off and at an outside tem­
perature below 39
°F (4 °(). In this posit ion ,
the w indshield wipers are in an area on the
g lass w hich is reached by the a ir vents below
the glass. It is also easier to remove snow and
ice from the wi ndshield wipers in this posi­
tion .
The wipe rs leave the w inte r position, when
the ign ition is swi tc h ed on, if the winds hield
wiper lever is operated or the active rain sen­
sor reacts to moistu re.
Rain sensor
The rain senso r operates on ly in the inte rva l
wiper position . When it sta rts to ra in , the in­
terval wipe r mode is activated automati ca lly.
If the windshie ld w iper lever is in the inte rval
wipe posit ion w ith the ign ition switched off, the ra
in sensor is not activated until ve hicle
sp eed is above 4 mph (6 km/h).
T o red uce the sensi tivi ty of the rain senso r,
the switch @ mus t be moved down . T o in­
crease the sensitivity of the rain sensor, the
switch must be moved up.
T he higher the sensit iv ity se tt ing , the sooner
the windshie ld wipers react to moist ure on
the windshie ld . I nc reased sensitivity is sig­
naled by the windshie ld wipers making a sin­
gle pass over the windshield.
T he rain sensor w iper intervals depend on the
sensitivity setting as well as vehicle speed.
D uring brief stops, wiper motio n will adj ust in
relat ion to the amount o f rain on the w ind­
shield .
A WARNING
-W iper blades are crucial for safe driving!
O nl y when they are i n good co ndit io n are
they able to clear the windows prope rly
to p rov ide uncompromised vis ib ility.
Wo rn o r damaged wipe r blades are a
safety ha zard
~ page 66, Replacing
windshield wiper blades!
- T he rain sen so r is only designed to assist
a nd suppor t the driver.
It rem ains enti re­
ly the d river 's responsibility to monitor
outside weathe r conditions and to man­
ually activate the wipe rs as soon as rain
or driz zle reduces visibility through the
windshie ld.
(D Note
In freezing or near freezing conditions:
- Always check that the w iper b lades are
not frozen to the g lass before you turn
the wipe rs on . Loosen a wiper blade
wh ich is frozen in place before operating
the wipers to prevent damage to the
w iper blade or the wiper motor.
- Do not use the w ipers to clear a frosted
w indow. Us ing the wipers as a conven­
ient ice scrape r will destroy the wiper
blades .

-Prior to using a car wash, the windshield
wiper system must be switched
off (lever
i n position 0) . This helps to prevent unin ­
tentiona l switching on and damage to
the windshie ld w iper system .
@ Tips
-The windshield wipers are switched off
when the ignition is turned off. Activate
the w indshield w ipers after the ignit ion
i s switched back on by moving the wind­
sh ield wiper lever to any pos ition.
- Worn or dirty windshield wiper blades
cause smearing which can affect the op­
eration of the rain sensor . Check the con­
dit ion of yo ur windshield wipe r blades
regularly.
- The rain sensor is part of the interval
wiping system. Turning
off the ignition
will a lso deact ivate the rain sensor. To re­
activate the sensor, sw itch
off the inter­
va l w iping function, then switch it back
on again.
- Make sure the washer fluid reservoir in
the engine compartment is topped
off
before going on a long trip . Look up
c:> page 2 79 for checking and fi lling the
washer container.
Rear window wiper
The wiper lever is also used to operate the
rear window wiper and the automatic wiper/
washer function.
Fig. 66 Wiper lever: activati ng th e rear window w iper
and washer
The rear window wiper and the automatic wip­
er/washer functions are activated as follows:
Clear vision 65
Intermittent wiping
.,. Push the wiper lever forward to the first po­
sition @<=:> fig. 66 . Th e rear window wiper
w ill wipe the window approx. every four sec­
onds.
Automatic wiper /washer function
.,. Push the wiper lever fo rward to the second
stop, position
(J), and hold it there for as
long as you want the rear wiper/washer to
operate.
.,. Release the lever again. the wiper will keep
running for approx. four seconds.
Switching intermittent wiper action off
.,. Pull the lever all the way back to the origi-
nal position .
As soon as the reverse gear is engaged and
the front w ipers are turned on and operating
at the same time, the rear w iper also turns on
automatically.
A WARNING
Wiper blades are crucial for safe driving!
Only in good condit ion are they able to
clear the w indows properly to provide un­
restricted visib ility. Worn or frayed w iper
blades are a safety hazard! <=:>page 66,
Replacing windshield wiper blades
(D Note
In freezing or near freezing conditions:
- Always check that the w iper b lades are
not frozen to the g lass before you turn
the wiper on. Loosen a wiper blade which
is frozen in place before operat ing the
w iper to prevent damage to the wiper
blade or the wiper motor.
- Do not use the w iper to clear a frosted
w indow . Us ing the wipers as a conven­
ient ice scrape r will destroy the wiper
blades.
-

66 Clear vis ion
Headlight washer system
Applies to vehicles: with hea dli ght washer system
The headlight washer system cleans the
headlights.
.. Operate the windsh ield wiper/washer sys­
tem
c:> page 63, fig. 65 ® with the head­
lights turned on by holding the lever for lon­
ger than one second.
The washer jets extend forward out of the
fro nt bumper driven by water pressure to
spray the front headlights with water .
You should inspect the headlights regularly
(for example when refueling) and clean off
any solid dirt or insects from the lenses .
To ensure the system works properly in winter,
keep the washer jets free of snow and remove
any ice using a de- ic ing spray.
Service position
The wiper blades can only be changed in the
service position.
.. If the wiper blades are not frozen to the
windshield, bring the windshield wiper lever
to the basic position@c:>
page 63 , fig. 65 .
.. Select: ICARI function button > Systems *
control button> Windshield w ipers > S erv­
i c e posit ion.
Or
.. Se lect:
ICARI funct ion button > Car s ys­
tems *
control button > Servicing & check s >
Wiper service po sition .
-On -changing the windsh ie ld w iper blades
can on ly be done if you bring the wiper a rms
to the se rv ice position. You w ill also avoid
paint damage to the hood when wo rking on
the wipers in this pos ition.
- Off -the w indshield wipe rs a re moved to
their initial pos ition aga in.
(D Note
Never maneuve r your vehicle with the
fro nt windshield wipe r arms r aised since
they will a utomat ically be moved back to the
ir basic position above a speed of 3
mph
(6 km/h) and can scratch the hood.
(D Tips
- Yo u ca n also use the se rvice posi tion, for
example, if you want to protect the
w indshield from icing by using
a cover .
- T he service posit ion automatically
switches to
Off when you operate the
w indshield wiper lever, o r speed exceeds
3 mph (6 km/h) .
Replacing windshield wiper blades
Wiper blades in good condition help keep the
windshield clear.
®
F ig . 67 Removing the wiper blades
F ig . 68 Instal ling wiper b lades
Removing a wiper blade
.. Bring the w indshield wipe rs to the se rvice
posi tion
c:> page 66.
.. Lift the wiper arm away from the wind­
shie ld .
.. Squeeze the plast ic bracket on the wind­
shie ld wiper arm together on both sides @
c:>
fig. 67 .
.. Turn the wiper blade away from the wiper
arm . ..,.

.. Lift the wiper blade off in the direction of
the arrow @.
Install ing wipe r blade
.. Place the new wiper b lade in the retainer on
the wiper a rm ©
r::!>fig. 68.
.. Swing the wipe r blade in the direction of
the arrow @against the wiper arm .
.. Squeeze the corrugation on the wiper until
you hear the bracket click in the wiper arm .
.,. Place the wiper arm back against the wind-
shield.
Clean your wiper blades regularly with a wind­
shie ld washer solution to prevent streaking. If
the blades are very dirty, for example with in­
sects, carefully clean the blades with a sponge
or a soft brush .
If the wiper blades begin to streak the wind­
shie ld, this could be caused by residue left on
the windshield by automatic car washes .
Fi ll the windshield washer container with a
specia l solution available at your authorized
Aud i dealer to remove the residue.
A WARNING
Be sure to inspect the condit ion of yo ur
w iper blades regularly. See yo ur author­
ized Aud i dea le r for r eplacement b lades .
(D Note
-The windshield wiper blades must only
be replaced whe n in the service position
r::!> page 66! Otherwise, yo u risk da mag-
i ng the pa int on the hood or the wind­
s h ield wiper motor.
- To he lp prevent damage to the wiper sys­
tem, a lways loosen blades which are fro­
z en to the windsh iel d befo re ope rat ing
wipe rs.
- To he lp prevent damage to w iper b lades,
do no t use g asoline, ke rose ne, pa int
t hi nner, or othe r so lven ts on or nea r th e
wipe r blades .
- To he lp prevent dam age to the wiper
arms or other components, do not at­
tempt to move the w ipers by hand .
Clear vision 6 7
@ Tips
Commercia l hot wa xes applied by auto­
matic car washes affect the cleana bility of
the windshield .
Changing the rear wiper blade
F ig . 6 9 Rear w indow w iper Detac hing the rear wiper
b lade
Removing the wiper bl ade
.. Fold the windshie ld w iper arm away from
the glass.
.. Grasp the upper end of the wiper a rm with
one hand and the metal clamp o n the wiper
b lade w it h the other
Q fig . 69.
.. Ho ld the wipe r arm in the direction of the
arrow @and pu ll th e wiper b lade out of the
holder on ly in the d irection of the arrow @.
Attaching the w iper blade
.,. Ad just the wiper b lade in the holder .
.. Ho ld the upper end of the wipe r arm wit h
one hand.
.. Press t he wiper b lade i nto the ho lder wi th
your other hand .
.. Fold the w iper arm back onto the wind­
shield.
A WARNING
- To avoid streaks, you should clean the
windshie ld w iper blades regu larly with
w indow cleaner. For heavy soiling, for ex­
ample, insects, the w iper blades can also
be cleaned w ith a sponge or a cloth.
- For safety reasons, the w indshield wipe r
blades should be replaced once or tw ice
a year.

344 Index
Glossary of tire and loading termino lo-
gy . ... .... ... ............ .. .... . 281
New tires and wheels ...... .. .. .... . 291
Tires and vehicle load limits .. .. ..... 288
When mus t a safety belt be rep laced? . . 178
When must the airbag system be inspect-
ed? .... ... .. ................ ... ... 195
When shou ld I adjust the tire pressures? 28 7
When shou ld I check the tire pressures? . 287
Where are lower anchorage s located? ... 219
Where can I find the tire pressures for my
car? . ... .. .. ............... .. .... . 286
Why safety belts? . . . . . . . . . . . . . . 175 , 176
Windows Cleaning . .. ................ ... .. . 249
Conven ience close/open feature . .. .... 53
Defogging . . . . . . . . . . . . . . . . . . . . . . . . . 94
Defrosting . . . . . . . . . . . . . . . . . . . . . . . . 94
Rapid defros ting/defogg ing .. .. .... .. 96
Windshield washer fluid Low level ............. ........ ... .. 35
W indshield w ipers
Changing the rear wipe r blade . . . . . . . . 67
Faulty . .. .......... ....... .. .. .. ..
37
Intermittent wiping ........... .. .... 63
One-tap w iping .... .... ..... .. .. .. .. 63
Ra in sensor . ..... ..... .... ... .. .. .. 63
Rear window w iper . ....... .. .. .. .. .. 65
Service pos it ion . . . . . . . . . . . . . . . . . . . . 66
Washer reservoir .......... ... .... . 279
W inter operation
Battery .. .. ................ ... ... 275
Coolant system ..... ..... .... .. .. . 271
H eated front seats . ....... .. .. .. .. . 100
H eated rear seats .......... ... .... . 101
Steering whee l heating ..... .... ... . 101
Tires . ................... ... .... . 231
W indows .. .... .. ... .. .. .. .. .. ... 249
W inter tires .. ... ..... ..... .. .. .. .. . 295
A ll-wheel drive ............ ... .... . 295
W iper blades
I nstalling new w iper blades ...... .... 66
also refer to Windshie ld wipers . . . 66, 67
X
Xenon-Lights . ................ ... .. . 312
y
Yellow symbo ls . . . . . . . . . . . . . . . . . . . . . . 34