warning AUDI Q7 2015 Owner´s Manual

298 Tires and wheels
Sustained high temperature can cause the
materia l of the tire to degenerate and reduce
tire life, and excessive temperature can lead
to sudden tire failure<=>,& .
The grade C corresponds to a level of perform­
ance which a ll passenger car tires must meet
under the Federa l Motor Veh icle Safety Stand ­
ard No.
109. Grades Band A represent higher
levels of performance on the laboratory test
wheel than the minimum required by law.
A WARNING
The traction grade assigned to this t ire is
based on stra ight-ahead braking traction
tests, and does not include acceleration,
cornering, hydroplanin g or peak traction
characteristics.
A WARNING ,.,.____
The temperature grade for this tire is es­
tablished for a tire that is properly inflated
and not overloaded. Excessive speed, un­
derinflation, or excessive loading, either
separately or in combination, can cause heat buildup and possible tire fa ilure.
Winter tires
Winter tires can improve vehicle handling on
snow and ice. At temperatures below 45 °F
(7 °C) we recommend changing to winter
tires .
In some heavy snow areas, loca l governments
may require true winter or "snow" tires, those
with very deeply cut tread. These t ires should
only be used in pairs and be installed on all
four wheels. Make sure you purchase snow
tires that are the same size and construct ion
type as the other tires on your ve hicle.
Your veh icle is equipped with all -wheel drive,
this will improve traction during w inter driv­
i ng, even with the standard tires. However, we
strongly recommend that you always equip all
four whee ls on your veh icle w ith correctly fit­
ted winter ti res or all-season tires, when win­
ter road conditions are expected. This a lso im- proves the vehicle's
braking performance and
reduces stopping distances.
Summer tires provide less gr ip on ice and
snow.
Winter tires (snow tires) must always be fitted
on all four wheels.
Ask your authorized Audi dealer or qualified
workshop for perm itted
winter tire sizes . Use
only rad ial winter t ires .
Winter tires lose their effectiveness when the
tread is worn down to a depth of
0.157 inch
(4 mm).
Only drive w ith w inter t ires under winter con ­
ditions. Summer t ires handle better when
there is no snow or ice on the roads and the
temperature is above 45 °F (7 °() .
If you have a flat tire, see notes on spare
wheel<=>
page 291 .
Please always remember that winter tires may
have a lower speed rating than the tires origi­
nally installed on your vehicle at the time it
was manufactured. Please see
<=>page 294,
Speed rating (letter code)
for a listing of the
speed rating letter codes and the maximum
speed at which the tires can be driven .
The speed rating letter code (<=>
page 2 76) is
on the side wall of the t ire
c> page 291.
A WARNING ,.___
Winter tires have maximum speed limits
that may be lower than your vehicle's max­
imum speed. Always know the maximum
speed before driv in g off. Never drive faster
than the speed permitted for your specific
winter tires. This wi ll cause damage to the
tires leading to an accident and serious
personal injury to you and your passen­
gers.
A WARNING
'----
Driving faster than the maximum speed
for which the winter tires on your vehicle were designed can cause t ire failure in­
cluding a blowout and sudden deflation,

M N
0 ...J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
loss of control, crashes and serious per­
sonal inj uries. Have worn or damaged tires
rep laced immediate ly.
- Winter tires have maximum speed rating
that may be lower than your veh icle's
maximum speed.
- Never drive faster than the speed for wh ich the winter or other tires installed
on your vehicle are rated.
A WARNING
Always adjust your driving to the road and traffic conditions . Never let the good ac­
celeration of the winte r tires and all-whee l
drive temp t you into taking extra r is k s. Al­
ways remembe r:
- When braking, an a ll-w heel driv e vehicle
hand les in the same way as a front dr ive
vehicle.
- Drive carefu lly and reduce your speed on
icy and slippery roads, even winter tires
c annot he lp un der blac k ice cond it ions.
@) For the sake of the environment
Use summe r tires when weathe r cond i­
tions perm it. They are quieter, do not wea r
as quickly and red uce fue l consumption.
Snow chains
Snow chains may be fitted on ly to the rear
wheels, and only to certain tire sizes . Ask yo ur
authorized Audi dealer on whic h tire sizes
snow chains can be used.
The snow chains must have low -profile links
a nd must not be thicker than 0 .S3 inch
(13 .5 mm), including the lock.
Remove wheel cente r covers and tr im discs
before p utting snow chains on you r vehicle
~ 0 . For safety reasons cover caps must the n
be fitted over the whee l bolts. These are avail­
ab le from authorized Audi dea lers.
A WARNING
Using the wrong snow chains for your vehi­
cle or installing them incorrectly can in-
Tire s an d wheel s 2 99
crease the risk of loss of contro l leading to
serious personal injury.
- Snow chains are available in different
sizes. Always make sure to follow the in­
structions prov ided by the snow chain
manufacturer.
- When driving with snow cha ins neve r
drive faster than the speed permitted for
your specific snow chains.
- Always observe local regulations.
([) Note
-Remove snow c hains be fore driving on
roads not covered with snow to avoid
damaging tires and wearing the snow
chains down unnecessarily.
- Snow chains, which come into direct con ­
tact with the whee l rim, can scratch or
damage it. Therefore, make sure that the
snow chains are s uitably covered. Check
t he pos itio n of the snow chains afte r
dr iving a few yards and co rrect if neces­
sary. Fo llow the inst ruct io ns from the
s now chain ma nufa ct urer when do ing so.
- If the Adaptive Ai r Suspens io n* s hou ld
ma lfun ction, do not mount o r use snow
c h ains be cause the ve hicl e w il l be ex­
t reme ly low. If you do d rive with snow
chains on while t he ve hicle is at this lev ­
el, the snow chains m ight seve rely dam ­
age the whee lhouse and other parts of
the vehicle.
(D Tips
Where snow chains are mandatory oncer ­
tain roads, th is normally a lso applies to
vehicles with all-wheel drive.
Wheel bolts
Wheel bolts must always be tightened to the
correct torque.
T he design of w heel bolts is matched to the
factory installed rims. If different rims a re fit­
ted, the correct wheel bolts with the right length and correct ly shaped bolt heads must
be used. Th is ensures that wheels are fitted .,..
•
•

300 Tires and wheels
securely and that the brake system functions
correctly .
I n certain circumstances, you may not use
wheel bolts from a different vehicle -even if it
is the same model
¢ page 328.
A WARNING
Improperly tightened or maintained wheel
bolts can become loose causing loss of
control, a collision and serious personal in­
jury.
- Always keep the wheel bolts and the
threads in the wheel hubs clean so the
wheel bolts can turn easily and be prop­
erly tightened.
- Never grease or oil the wheel bolts and
the threads in the wheel hubs. They can
become loose while driving if greased or
oiled, even if tightened to the specified
torque.
- Only use wheel bolts that belong to the
rim being installed.
- Never use different wheels bolts on your
vehicle .
-Always maintain the correct tighten ing
torque for the wheel bolts to reduce the
risk of a wheel loss.
If the tightening tor­
que of the wheel bolts is too low, they
can loos en and come out when the vehi­
cle is moving .
If the tightening torque is
too high, the whee l bolts and threads
can be damaged and the wheel can be­
come loose.
{[) Note
The specified torq ue for the wheel bolts is
120 ft lb (160 Nm) with a tolerance of
± 7,4 ft lb(± 10 Nm). Torque whee l bolts
diagonally. After changing a whee l, the
torque must be checked as soon as possi­
ble with a torque wrench -preferably by an
author ized Audi dealer or qualified work­
shop.
Low aspect ratio tires
Your Audi is factory-equipped w ith low aspect
ratio tires. These tires have been thoroughly
tested and been se lected specifically for your
model for their superb performance, road feel
and handling under a variety of driving condi­
t ions . Ask your authorized Audi dealer for
more details.
The low aspect ratio of these tires is indicated
by a numera l of
55 or less in the tire's size
designation. The numera l represents the ratio
of the tire's sidewall height in relation to its
tread width expressed in percentage. Conven­
t iona l tires have a he ight/w idth ratio of 60 or
more .
The performance of low-aspect-ratio tires is
particularly sensitive to improper inflation
pressure. It is therefore important that low
aspect ratio tires are inflated to the specified
pressure and that the inflation pressure is
regularly checked and maintained. Tire pres­
sures should be checked at least once a
month and always before a long trip
¢ page 282, Checking tire pressure .
What you can do to avoid tire and rim
damage
Low aspect ratio tires can be damaged more
easily by impact with potholes, curbs, gullies
or ridges on the road, particularly if the tire is
underinflated .
In order to minimize the occurrence of impact
damage to the tires of your vehicle, we recom­
mend that you observe the following precau­
tions:
- Always maintain recommended inflation
pressures. Check your tire pressure every
2,000 miles (3,000 km) and add air if neces­
sary .
- Drive carefully on roads with potholes, deep
gullies or ridges. The impact from dr iving
through or over such obstacles can damage
your tires. Impact with a curb may also cause damage to your tires .
- After any impact, immed iately inspect your
tires or have them inspected by the nearest
II>

302 Tire s and whee ls
Tire pressure indicator appears
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too
low or if there is a system malfunction.
F ig . 255 D isp lay: underinflation warn ing
Using the ABS sensors, the tire pressure moni­
toring system compares the tire tread circum­
ference and vibration characteristics of the in­
d iv idual tires. If the pressure decreases in one
or more tires, this is indicated in the instru­ ment cluster with a
RE warning symbol and a
message ¢
fig. 255 . The dr iver message in the
d isplay goes out after 5 seconds . The dr iver
message can be displayed again by pressing
the
! CHECK I button. If only one tire is affect­
ed, the display will indica te its pos ition.
The tire pressure monitoring must be reset via MMI each time the pressures are adjusted (e.
g. when switch ing between partial and full
l oad pressure) or after changing or replac ing a
tire on your vehicle¢
page 303. The TPMS in­
dicator only monitors the tire pressure that
you have previously stored. You can find the
recommended tire pressures for your vehicle
on the label on dr iver's side 8-pillar
¢page 278.
Tire tread circumference and vibration charac­
teristics can change and cause a tire pressure
warn ing if:
- the tire pressure in one or more tires is too
l ow,
- the tire has st ructural damage,
- the tire pressure was changed, whee ls rotat-
ed o r replaced but the TPMS was not reset
¢ page 303,
-the sp are tire* is mounted.
Warn ing symbo ls
RE Loss of pressure in at least one tire¢,&..
Check the tire or tires and rep lace or repa ir if
necessary . The
RE indicator light in the instru ­
ment cluster also illuminates
¢ page 14.
Check/correct the pressures of all four tires
and reset TPMS via MMI.
[m'El (T ire Pressure Monitoring System) Tire
pre ssure: System m alfunction!. If [m'El ap­
pears after switching the ignition on or while
driving and the
RE i ndicator light in the in­
strument cluster bli nks for approx imately one
minute and then stays on, there is a system
malfunction . Attempt to store the correct tire
pressure
¢ page 303. If the indicator light
does not tu rn off or if it t urn s on sho rtly
thereafte r, immediately d rive yo ur vehicle to
an a uthorized Audi dea ler or a uthorized repair
facility to have the malfunction corrected.
A WARNING ......_
- If the tire pressure ind icator appears in
the instrument cluster display, one or
more of your t ires is sign ificant ly under­
inflated . Reduce your speed immediately
and avoid any hard steer ing or b raking
maneuvers. Stop as soon as possib le and
check the tires and their pressu res. In ­
flate the ti re p ressu re to the proper pres ­
sure as indicated on the vehicle's tire
pressure labe l
r=:>page 278. Driving on a
sign ificantly under-inflated tire causes
the t ire to overheat and can lead to tire
fa ilure. Under-inflation also is likely to
impair the vehicle's handl ing and stop­
p ing ability .
- The driver is responsible for maintaining
the correct tire pressures. You must
check the tire pressures regu larly.
- Under certain conditions (such as a spor­
ty driv ing style, winter conditions or un­
paved roads), the pressure monitor indi­
cator may be delayed .
-Ask you r aut horized Aud i dea ler if run­
flat t ires may be used on you r vehicle.

304 What do I do now?
What do I do now?
Jack, tools and
inflatable spare tire
Tools
The tool kit is located in the luggage com­
partment under the cargo floor cover.
Fig . 256 Luggage compartmen t: vehicle too l kit
The onboard tool kit includes:
- Hook for removing wheel covers*
- Plastic hook to remove wheel bolt covers*
- Wheel bolt wrench
- Alignment p in for changing wheels
- Screwdriver with reversible blade
- 10 x 13 open ended wrench
-Towing eye
(D Tips
Some of the onboard items listed above
are provided on certa in models only or are
optional extras .
Jack and folding chocks
The jack and the folding chocks are located in
the luggage compartment under the cargo
floor cover.
Fig. 257 Luggage compartment veh icle jack and fo ld­
ing chocks
-----........ -
Fig. 258 Opening fold ing chocks
Vehicle jack
The jack is located under the tool kit
<=>fig . 257. Before storing the jack, make sure
it is wound back down as far as it will go.
Folding chocks
Two unassembled fo lding chocks are attached
to the foam section at the front with the jack
<=> fig. 257.
Release the two hook-and-loop fasteners, and
remove the two chocks. To use the chocks, you
first have to raise the support plate
<=> fig. 258 (!) and then insert the locking plate
with the two "tabs" into the elongated holes
in the base plate@<=>&. .
A WARNING
-- The chock cannot fulfill its function and
may lose its stability if the "tabs" on the
support plate are not inserted correctly
into the elongated holes in the base

M
"' 0 _,
"". rl I.O
"' rl
"' rl
plate. If this hap pens , the vehicle may
start to m ove whi le a whee l is being
changed.
- Never use the folding chocks if they are
damaged or i f they have not been assem­
bled correct ly.
A WARNING
Improper use of the vehicle jack can cause
ser ious personal injuries.
- Never use the jack supplied with your
Audi on another vehicle, particularly on a heavier one. The jack is only suitable for
use on the vehicle it came w ith .
- Us ing a bumper jack to raise the vehicle
will damage the bumper system. The
jack may slip, causing i njury.
- Never support your vehicle on cinder bloc ks, b ricks or other objects. Th ese
may not be able to support the load and
cou ld cause injury when they fail.
- Never start or run t he engine while the
vehicle is suppor ted by the jack.
- If you must wo rk under the vehicle, al­
ways use safety stand s spe cifically de­
signed for this purpose.
- Always make sure the inflatable spare
tir e a nd even a f lat t ire are se cured in
place and not loose, ot herwise they
cou ld fly forward, causing personal inj ury
to passengers in the veh icle in an acc i­
dent or sudden mane uver.
Removing bass box
Applies to vehicles: with bass box
Before the inflatable spare tire can be taken
out, the bass box must be removed .
Fig . 259 Spare wheel well: Bass box
What do I do now ? 305
Removing bass box
.,. Squee ze the locking tabs ~ fig . 259 (D of
the conne ctor .
.,. Disconnect the connector @and place the
lead to one side.
.,. Turn the large screw counter-clockwise .
.,. Carefully remove the bass box.
Installing bass bo x
.,. Carefully p lace the bass box in the wheel.
The inscription "F RO NT" on the bass box
must face forward .
.,. Reconnect the connector that was removed.
.,. Secure the bass box with the large screw .
Inflatable spare tire
The inflatable spare tire expands to its full di­
ameter when it is inflated.
Fig. 2 60 In flatable spare tir e w ith compressor
Removing inflatable spare tire
.,. Lift up the cargo floo r us ing the handle .
"' Turn the large screw
9 fig . 260 counte r-
clockw ise.
"' Remove the bass box as required
¢ page 305 .
.,. Take out the in flatable spare tire .
.,. Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
9 page 169.
Stowing the inflatable spare t ire
"' Release the ai r by u nscrewing the valve
stem .
.,. Screw the valve stem back in afterwards .
.,. Wait a few hours before p lac ing the wheel in
the spare wheel we ll¢ ,& .
"' Install the bass box as required ¢
page 305 . ..,_

306 What do I do now?
• Secure the wheel with the large screw.
• Fold the cargo floor back down .
After using th e inflat able spare wheel
The inflatable spare t ire can be re-used as
l ong as it is not damaged and is not worn
down to the tread wear ind icators
c::> A .
When you let the air out of the inflatable
spa re tire, it does not assume its folded shape
again for several ho urs. Until then, it cannot
be p laced back in the spare wheel well and
stowed securely.
A WARNING
- Never use the spare tire if it is damaged
or if it is worn down to the tread wear in­
dicators.
- If the inflatable spare tire is more than 6
years old, use it on ly in an emergency
and w ith extreme caut ion and careful
dr iv ing .
- The inflatable spare tire is intended only
for temporary and short-term use .
It
should be replaced as soon as possible
with the no rmal wheel and tire .
- The tire pressure value for the inflatable
spare t ire is located on the driver's side
B-p illar
c::> page 278, fig . 251 .
-Maximum perm iss ible speed is SO mph
(80 km/h).
- Avoid full-throttle acce le rat ion, heavy
braking, and fast corner ing .
- When the air is let out of the inflatable
spare wheel, it does not assume its fold­
ed shape for several hours . Until then, it
cannot be placed back in the spare wheel
we ll and stowed secu rely.
- Never drive with more than one inflata­
ble spare ti re.
- For technical reasons, the use of ti re
chains on the inf latable spare tire is not
permitted.
If i t is necessary to drive w ith
t ir e cha ins, the infla table spare whee l
must be moun ted on the front axle in the
event of a flat in a rear tire . The newly
available front whee l must the n be in­
sta lled in place of the rear wheel with the flat tire
. Insta lling the t ire cha in be­
fore mounting the wheel and tire is rec­
ommended.
- Loose items in the passenger compart­
ment can cause serious personal injury
during hard brak ing or in a n accident.
Never store the inflatable spare tire or
jack and tools in the passenge r compart­
ment.
(D Note
- The inflatable spare tire has been deve l­
oped specifically for t his veh icle mode l.
It must not be exchanged or used for
other vehicle models. Sim ila rly, inflata­
ble t ires from other vehi cle models m ust
no t be used.
- Norma l summer or w inte r ti res m ust not
be ins talled on the infla table t ire rim.
Inflating inflatable spare tire
• Remove the compressor from the luggage
compa rtment
c::> page 305 , fig. 260.
• Unscrew the valve stem from the spare tire.
• Screw the tire f iller hose from the compres­
sor firmly onto the
va lve of the spare tire.
• Insert the plug from the compressor into an
outlet of the ve hicle
c::> page 90 .
• Switch the comp resso r on .
• Let the compressor run unti l the va lue speci­
fied on the ti re p ressu re label is reached
c::> page 278, fig. 251 . Switc h the compres­
sor off after running for 12 m inutes at the
most -danger of overheating!
A WARNING
-The compressor and the tire f iller hose can
become extremely hot while t hey are run­
n ing -danger of burns!
([) Note
Switch the compressor off after ru nning
for 12 min utes at the most -danger of
overheating! Allow the compressor to cool
down for a few m inutes before you use it
again .

M N
0 ..J
'SI: ,...., \!) ..,.,
,...., ..,., ,....,
Changing a wheel
Before changing a wheel
Observe the following precautions for your
own and your passenger's safety when chang­
ing a wheel .
.,. After you experience a tire fa ilure, pull the
car well away from moving traffic and try to
reach
level gro und before you stop¢.&_ .
.. All passengers should
leav e the car and
move to a safe location (fo r instan ce, be hind
the guardra il)¢ .&_.
.,. Engage the
parkin g brake to prevent your
vehicle from ro lling unintentionally¢ .&_.
.. Move
selecto r le ver to p osition P ¢ .&_ .
1> Ifyou are towing a trai ler: unhitch the trail­
er from your veh icle.
.,. Block the diagonally opposite wheel with
the folding chocks or other objects.
.. Take the
jack and the inflatab le spare tire
out of the luggage compartment
¢page 304.
& WARNING
You or your passengers cou ld be injured
while changing a whee l if yo u do not fol­
low these safety precautions:
- If you have a flat t ire, move a safe dis ­
tance off the road . Turn off the eng ine,
t ur n the emergency flashers o n and use
other warning devices to alert other mo­
torists.
- Make sure that passengers wait in a safe
place away from the vehicle and well
away from the road and traffic.
- To he lp prevent the veh icle from mov ing
sudden ly and possibly slipping off the
jack, always fully set the parking b rake
and block the whee l diagonally opposite
the wheel being cha nged with the fo ld­
ing chocks or othe r objects. When one
front whee l is lifted off the g ro und, plac­
ing the A utomat ic Transm iss ion in P
(Park) wi ll
not prevent the vehicle from
moving .
-
What do I do now? 307
-Before you change a whee l, be sure the
ground is level and firm. If necessary,
use a sturdy board under the jack.
- Always store the vehicle tool kit, the jack
and the replaced tire in the luggage com­
partment
<=:>page 169 .
Changing a wheel
When you change a wheel, follow these­
quence described below step-by-step and in
exactly that order.
1. Activate the vehicle jack mode (only
vehicles with Adaptive Air S uspension)
¢ page 161 .
2. Remove the decorati ve wheel co ver* . For
more details see also <=:>
page 308, Deco­
rative wheel covers
or <=:> page 308,
Wheels with wheel bolt caps.
3. Loosen the wh eel bolt s¢ page 308 .
4. Loca te the p roper mounting point for the
jack and align the jack be low that point
¢ page 309.
5. Lift the car with the jack Q page 309 .
6. Remove the wheel with the flat ti re and
then install the
inflatable spare tire
¢ page 310.
7. Tig hte n all wheel bolts lightly.
8.
L owe r the vehicle with the jack .
9. Use the wheel bolt w rench and
firmly
t ighten all wheel bolts¢ page 308.
10. Replace the decora tive whe el co ver* .
11. Deactivate the vehicle jack mode (on ly
vehicles with Adaptive Air S uspension)
¢ page 161 .
A WARNING
Always read and follow all WARNINGS and
informat ion<=:>
& in Raising the vehicle on
page 310
and <=:> page 311.
•
•

M
"' 0 ..J
"". rl I.O
Loosening
• Install the wheel bolt wrench over the
whee l bolt and push it down as far as it wi ll
go.
• Take tight hold of th e
end of the wrench
handle and turn the whee l bolts
counter­
clockwise
abou t one single turn in the di rec·
tion of arrow
c::> fig. 263 .
Tightening
• Install the wheel bolt wrench over the
wheel bolt and push it down as far as it will
go .
• Take tight hold of the
end of the wrench
handle and turn each wheel bolt
clockwise
until it is seated .
& WARNING
-Do not use force or hurry when changi ng
a whee l· you can cause the vehicle to slip
off the jac k and cause serious personal
injuries .
-Do not loosen the wheel bolts more than
one turn
before you raise the veh icle with
the jack. -You risk an injury.
(j) Tips
If a wheel bolt is very tight, you may find it
easie r to loosen by carefully pushing down
on the end of the wheel bolt wrench with
one foot only. As you do so, hold on to the
car to keep yo ur balance and take care not
to slip.
Raising the vehicle
The vehicle must be lifted with th e jack first
before the wheel can be removed .
"' rl "' Fig. 264 Sill pane ls: m arkin gs rl
What do I do now? 309
Fig. 265 Sill: p ositioning the jack
• Activate the vehicle jack mode* (only
veh icles with Adaptive Air Suspension)
c::> page 161 .
• Engage the parking brake to prevent your
vehicle from rolling unintentionally
• Move the
selector lever to position P .
• Find the marking (imprint) on the sill that is
nea rest the whee l that will be changed
c::> fig. 264. Behind the marking, there is a
lifting point on the sill for the jack.
• Turn the
jack located under the lifting point
on the sill to raise the jack until its arm@
c::> fig. 265 is located under the designated
plastic mount
c::> .&. c::> Q) .
• Align the jack so that its arm@ c::> fig. 265
engages in the designated lifting point in
the door s ill and the movable base® lies
flat on the ground. The base@ must be
ver­
tical
under the lifting point@.
• Wind the jack up further until the flat tire
comes off the ground
c::> .,& .
Position the jack only under the designated
lifting points on the sill
c::> fig. 264. There is
exactly
one locat ion for each whe el. The jack
must not be positioned at any other location
c::> .&. c::> Q).
An unstable surface under the jack ca n cause
the vehicle to slip off the jack. Always provide
a firm base for the jack on the ground . If nec ­
essary place a sturdy board or similar support
under the jack . On
hard, slippery surfaces
(such as tiles) use a rubber mat or similar to
prevent the jack from slipping
c::> ,&.. .,,.

310 What do I do now?
& WARNING
-You or your passengers could be injured
while changing a wheel if you do not
follow these safety precautions:
- Position the jack only at the designated
lifting points and align the jack. Other­
wise, the jack could slip and cause an injury if it does not have sufficient hold
on the vehicle.
- A soft or unstable surface under the
jack may cause the vehicle to slip off the jack. Always provide a firm base for
the jack on the ground . If necessary,
use a sturdy board under the jack.
- On hard, slippery surface (such as tiles)
use a rubber mat or similar to prevent
the jack from slipping.
- To help prevent injury to yourself and
your passengers:
- Do not raise the vehicle until you are
sure the jack is securely engaged.
- Passengers must not remain in the ve­
hicle when it is jacked up.
- Make sure that passengers wait in a
safe place away from the vehicle and
well away from the road and traffic.
- Make sure jack position is correct, ad­
just as necessary and then continue to
raise the jack.
(D Note
Do not lift the vehicle by the sill. Position
the jack only at the designated lifting
points on the sill. Otherwise , your vehicle
will be damaged.
Taking the wheel off /installing the
inflatable spare tire
Follow these instructions step-by-step for
changing the wheel
Fig. 266 Changing a wheel: alignment pin inside the
top hole
After you have loosened all wheel bolts and raised the vehicle off the ground, remove and
replace the wheel as follows:
Removing the wheel
.,. Remove the topmost wheel bolt completely
and set it aside on a
clean surface.
.,. Screw the threaded end of the
alignment
pin
from the tool kit hand-tight into the
empty bolt hole
¢ fig . 266.
.,. Then remove the other wheel bolts as de­
scribed above.
.,._Takeoff the wheel leaving the alignment pin
in the bolt hole ¢(D.
Putting on the inflatable spare tire
.,. Inflate the inflatable spare tire ¢ page 306
and push the wheel over the alignment pin.
"Screw in and tighten all wheel bolts
slightly.
.,. Remove the alignment pin and insert and
tighten the remaining wheel bolt slightly
like the rest .
.,. Turn the jack handle counter-clockwise to
lower the vehicle until the jack is fully re­
leased .
" Use the wheel bolt wrench to tighten all
wheel bolts firmly ¢
page 308 . Tighten
them
crosswise, from one bolt to the (ap­
proximately) opposite one, to keep the
wheel centered.