page 34 AUDI Q7 2018 Owner´s Manual

0 a, .... N
" N
increase the tire pressure to the
maximum specified pressure¢,& .
Checking/correcting tire
pressure
.,.Check the tire pressure at least
once per month and also check it
before every long drive.
.,.Always check the tire pressure
when the tires are
cold. Do not
reduce the pressure if it increas­
es when the tires are warm .
.,.Check the labe l¢
fig. 2 72 for
the correct tire pressure based
on vehicle load.
.,,.Correct the tire pressure if nec­
essary.
.,.Store the new tire pressure in
the Infotainment system
¢ page 349.
& WARNING
Always adapt the tire pressure
to your driving style and vehicle
load.
-Overloading can lead to loss of
vehicle control and increase
Tire pressure table
Please note that the information
contained in the following table
was correct at the time of print­ ing, and the information is sub-
...
g ject to change. If there are differ-l: ..
Wheels
the risk of an accident. Read
and follow the important safe­
ty precautions in ¢
page 343,
Tires and vehicle load limits.
-The tire must flex more if the
tire pressure is too low or if
the vehicle speed or load are
too high. This heats the tire up
too much . This increases the
risk of an accident because it
can cause the tire to burst and
result in loss of vehicle con­
trol.
-Incorrect tire pressure in­ creases tire wear and has a negative effect on driving and
braking behavior, which in­
creases the risk of an accident.
@ Note
Replace lost valve caps to re­
duce the risk of damage to the
tire valves.
@ For the sake of the environment
Tire pressure that is too low in­
creases fuel consumption .
ences between this information
and the tire pressures specified
341

Wheels
on the label on the driver's side B­
pillar, always follow the specifica­
tion on the B-pillar label
r::=> page 340, fig. 271.
Make sure that the tire designa­
tion on your tire matches the des-
Model/ Tire designation
ignation on the tire pressure label
and the tire pressure table.
The following table lists recom­ mended tire pressures in cold
tires according to the load and
the size of the tires installed.
Tire pressure
Engine Normal load Maximum load
(up to 3 people)a)
front rear front rear
PSI kPA PSI kPA PSI kPA PSI kPA
Q7:
255/60 R18 108H 32 220 32 220 32 220 35 240
2.0L 255/55 R19 111H 32 220 32 220 32 220 35 240
4 cylinders
285/45 R20 112H 32 220 32 220 32 220 35 240
Gasoline en-
gine 285/45 R20 112V
32 220 32 220 32 220 35 240
285/40 R21109Y 32 220 32 220 32 220 35 240
285/35 R22 106V 32 220 3
2 220 35 240 38 260
Q7: 255/60 R18 108H 32 22 0 32 22 0 32 22 0 35 2
40
3.0L 255/55 R19 111H 32 220 32 220 33 230 36 250
6 cylinders
285/45 R20 112H 32 22 0 32 22 0 32 22 0 35 2
40
Gasoline en-
gine 285/45 R20 112V
32 220 32 220 32 220 35 240
285/40
R21109Y 32 220 32 220 3 2 220 35 240
285/35 R22 106V 32 220 32 220 38 260 41 280
Q7: 255/60 R18 108H 32 2
20 32 220 33 230 3 6 250
3.0L
255/55 R19 111H 32 220 32 220 35 240 38 260
6 cylinders
285/45 R20 112H 32 220 32 220 33 230 36 250
Diesel engine
285/45 R20 112V
32 220 32 220 33 230 36 250
285/40 R21109Y 32 22 0 32 22 0
33 2
30
36 2
50
285/35 R22 106V 32 220 32 220 39 270 42
290
SQ7: 255/55 R19 111H 35 2
4 0
35 24
0
36 25
0
39 27
0
4.0L
285/45 R20 112V 35 240 35 240
36 250 39 270
a-cylinder
285/45 R20 112H 35 240
35 240
36 250
39 270
diesel engine
285/40 R21109Y
35 240 35 240
39 270 42
290
285/35 R22 106V 38 2 60 38 260 45 310 48 330
a) 2 peop le in the front , 1 person in the rear
342

0 a, .... N
" N .... 0
0
l: ..
& WARNIN G
Please note the important safe­
ty precautions regarding tire
pressure
c:::> page 340 and load
limits
c:::>poge 343.
Tires and vehicle load limits
There are limits to the amount of
load or weight that any vehicle
and any tire can carry. A vehicle
that is overloaded will not handle
well and is more difficult to stop.
Overloading can not only lead to
loss of vehicle control, but can al­
so damage important parts of the
vehicle and can lead to sudden
tire failure, including a blowout
and sudden deflation that can
cause the vehicle to crash .
Your safety and that of your pas­ sengers also depends on making
sure that load limits are not ex­
ceeded . Veh icle load includes ev­
erybody and everything in and on
the vehicle . These load limits are
technically referred to as the vehi­
cle's
Gross Vehicle Weight Rat ­
ing ("GVWR").
The "GVWR" includes the weight
of the basic vehicle, all factory in­
stalled accessories, a full tank of
fuel, oil, coolant and other fluids
Wheels
plus maximum load . The maxi­
mum load includes the number of
passengers that the vehicle is in­
tended to carry ("seating capaci­
ty ") with an assumed weight of
150 lbs. (68 kg) for each passen ­
ger at a designated seating posi­
tion and the total weight of any
luggage in the vehicle . If you tow
a trailer, the weight of the trailer
hitch and the tongue weight of
the loaded trailer must be includ­ ed as part of the vehicle load .
The
Gross A xle Weight Rating
(" GAWR ") is the maximum load
that can be applied at each of the
vehicle's two axles.
T he fact that there is an upper
limit to your vehicle 's Gross Vehi­
cle Weight Rating means that the
total weight of whatever is being
carried in the vehicle (including
the weight of a trailer hitch and
the tongue weight of the loaded
trai ler) is lim ited. The more pas­
sengers in the vehicle or passen ­
gers who are heavier than the
standard weights assumed mean
that less weight can be carried as luggage.
The Gross Vehicle Weight Rating and the Gross Axle Weight Rating .,.
34 3

Wheels
are listed on the safety compli­
ance sticker label located on the
driver's side B-pillar.
A WARNING ,-= · -
Overloading a vehicle can cause
loss of vehicle control, a crash
or other accident, serious per­
sonal injury, and even death .
-Carrying more weight than your vehicle was designed to carry will prevent the vehicle
from handling properly and i ncrease the risk of the loss of
vehicle control.
-The brakes on a veh icle that
has been overloaded may not
be able to stop the vehicle
within a safe distance.
-Tires on a vehicle that has been overloaded can fail sud­
denly, including a b lowout and
sudden deflation, causing loss
of contro l and a crash.
-Always make sure that the to­ tal load being transported -i nc luding the weight of a tra il­
er hitch and the tongue
weight of a loaded trailer­
does not make the vehicle
h eavier than the vehicle's
Gross Vehicle Weight Rating.
3 44
Determining correct load
limit
Use the example below to calcu­
late the tota l weight of the pas­
sengers and luggage or other
things that you plan to transport
so that you can make sure that
your vehicle will not be over load ­
ed.
Steps for Determining Correct Load Limit
1 . Locate the statement " TH E
COMBIN ED WE IGH T OF OCC U­
PANTS AND CARGO SHOU LD
NEVER EXCEED XXX KG OR XXX
LBS" on your vehic le's placard
(tire inflation pressure label)
¢ page 340, fig . 272 .
2. Determine the combined
weight of the drive r and pas­
sengers that will be riding in
your vehicle.
3. Subtract the combined weight
of the driver and passengers
from
"XXX" kilograms or "XXX"
pounds shown on the stick­
er ¢
page 340, fig. 272 .
4. The resu lting figure equa ls the
available amount of cargo and
luggage load capacity . For ex­
ample, if the "XXX" amount
eq uals 1400 lbs. and there will~

Cl a:, ...... N
" N ...... 0
0
::r ' be five 150 lb s. pa ssenge rs in
y o ur vehi cle, th e am ount of
ava ilable cargo a nd lu ggage
l oa d cap acity is 650 lb s.
(1400-750 (5
X 150) = 650
lb s.)
5 . Determine th e combined
w eight of lu gga ge and cargo
bein g load ed on the vehicle .
Th at w eight m ay not sa fel y
ex ­
ceed th e av ail able car go and
lu ggage l oad capa city ca lc ul at­
e d in St ep 4 .
6 . If your vehicle will b e to wing a
tr ail e r, load from your tr ailer
will b e tran sferr ed to your
v e­
hi cle . C on sul t thi s manual t o
dete rmin e how this re du ces
th e av ailabl e c argo and lug­
ga ge load cap acity o f your vehi­
c le.
.,. Che ck th e tir e s idewall
(c:::> p ag e 33 1, fig. 269) to det er­
min e the de signated load r ating
for a specific tire.
Wheel bolts and rims
Wheel bolts
Wheel bolts must be clean and loosen/t ighten
eas ily .
Rims
Rims w ith a bolted rim ring* o r with bolted wheel
cove rs* consis t of multip le pieces. These compo­
nents were bolted together using specia l bolts
Wheels
and a spec ia l proced ure. Yo u must not repair or
disass emb le them <::>
.&..
A WARNING
--
Wheel bo lts that are tightened or repaired in­
correct ly can become loose and resu lt in loss
of vehicle contro l, wh ich increases the risk of
an accident . For the cor rect tighten ing specifi­
cation, see <::>
page 362, Finishing .
-Always keep the wheel bolts and the
threads in the wheel h ub clean and free of
g rease .
- Only use wheel bolts that fit the rim .
- Always have damaged rims repaired by an
author ized Audi dealer or author ized Audi
Serv ice Facility . Never repair or disassemb le
rims yo urself, because th is increases the r isk
of an acc ident.
Winter tires
Winter tires sign ifican tly imp rove the vehi cle's
handling when dr iv ing in winter conditions . B e­
ca use of their const ruct ion (w idth, compou nd,
tread pattern), summer tires provide less trac ­
tion on ice and snow .
.,. Use winter tires on all four wheels.
.,. On ly use winter tires that a re app roved fo r yo ur
ve hicle.
.,. Please not e that th e maximum permitted
speed may be lower with winter ti res
c:> &. in
General information on page 330 .
An author­
ized Aud i dealer or authori zed Aud i Serv ice Fa­
cility can inform you about t he maximum per ­
m itted speed for your tires .
.,. Check the tire p ressure afte r insta lling wheels
<::> page 340 .
The effectiveness of w inter tires is reduced great­
ly when t he tread is wo rn down to a depth of
0.16 in (4 mm). The cha racter istics of w inte r
t ir es also decrease g reatly as the t ire ages, re ­
gard less o f th e rem aining t read.
@ For the sake of the environment
Reinstall summer tires at the app ropr iate
time , beca use they prov ide bette r handling
when roa ds are free o f snow and ice. Summer ..,.
345

Wheels
tires cause less road noise, tire wear and fuel
consumption.
(D Tips
You can also use all season tires instead of
winter tires. Please note that in some coun­
tries where winter tires are required, only
winter tires with the
& symbol may be per­
mitted.
Snow chains
Snow chains not only improve the driving in win­
ter road conditions, but also the braking .
~ Only install snow chains on the front wheels.
~ Check and correct the seating of the snow
chains after driving a few feet, if necessary . Fol­
low the instructions from the manufacturer.
~ Note the maximum speed of 30 mph (SO km/
h). Note the local regulations.
Use of snow chains is only permitted with certain
rim/tire combinations due to technical reasons.
Check with an authorized Audi dealer or author­
ized Audi Service Facility to see if you may use
snow chains.
Use
fine-mesh snow chains . They must not add
more than 0 .53 in (13.5 mm) in height, including
the chain lock.
You must remove the snow chains on roads with ­
out snow. Otherwise, you could impair driving
ability and damage the tires.
.&_ WARNING
Using incorrect snow chains or installing snow
chains incorrectly can result in loss of vehicle
control, which increases the risk of an acci­
dent.
(LlJ) Note
- Snow chains can damage the rims/wheel
covers* if the chains come into direct con­
tact with them. Remove the wheel covers*
first. Use coated snow chains.
- Do not install and use snow chains if there is
a malfunction in the air suspension*, be­
cause the vehicle height will be
very low. If
346
you drive with snow chains anyway, the
wheel housings and other vehicle compo­ nents can be severely damaged.
(D Tips
When using snow chains, it may be useful to
switch the offroad mode on
r=> page 143.
Low-profile tires
Applies to: vehicles with low-profile tires
Compared to other tire/rim combinations, low­
profile tires offer a wider tread surface and a
larger rim diameter with shorter tire sidewalls.
This results in an agile driving style. However, it
may reduce the level of comfort and increase
road noise when driving on roads in poor condi­
tion.
Low -profile tires can become damaged more
quickly than standard tires when driving
over
large bumps, potholes, manhole covers, and
curbs . Therefore, it is particularly important to
maintain the correct tire pressure
r=.> page 340.
To reduce the risk of damage to the tires and
rims, drive
very carefully on poor roads.
Check your wheels regularly every 2,000 mi
(3,000 km) for damage . For example, check for
bulges/cracks on the tires or deformations/
cracks on the rims.
After a heavy impact or damage, have the tires
and rims inspected or replaced immediately by
an authorized Audi dealer or authorized Audi
Service Facility.
Low-profile tires can wear out faster than stand­
ard tires .
Uniform tire quality grading
- Tread wear
- Traction AA ABC
- Temperature ABC
Quality grades can be found where applicable on
the tire side wall between tread shoulder and maximum section width
r=.> page 331, fig. 269.

Wheels
Please note that the TPMS is not a substitute for
proper tire maintenance, and it is the driver's re­
sponsibility to maintain correct tire pressure,
even if under-inflation has not reached the level
to trigger illumination of the TPMS low tire pres­
sure telltale.
Your vehicle has also been equipped with a TPMS
malfunction indicator to indicate when the sys­
tem is not operating properly. The TPMS mal­
function indicator is combined with the low tire pressure telltale. When the system detects a
malfunction, the telltale will flash for approxi­
mately one minute and then remain continuously
illuminated. This sequence will continue upon
subsequent vehicle start-ups as long as the mal­
function exists.
When the malfunction indicator is illuminated,
the system may not be able to detect or signal
low tire pressure as intended. TPMS malfunctions
may occur for a variety of reasons, including the
installation of replacement or alternate tires or
wheels on the vehicle that prevent the TPMS
from functioning properly . Always check the
TPMS malfunction telltale after replacing one or
more tires or wheels on your vehicle to ensure
that the replacement or alternate tires and
wheels allow the TPMS to continue to function
properly.
If the tire pressure monitoring indicator
appears
Applies to: vehicles with Tire Pressure Monitoring System in­
dic ato r
The tire pressure indicator in the instrument
cluster informs you if the tire pressure is too low
or if there is a system malfunction.
Using the ABS sensors, the tire pressure monitor ­
ing system compares the tire tread circumfer­
ence and vibration characteristics of the individu­
al tires . If the pressure changes in one or more
tires, this is indicated in the instrument cluster
display with an indicator light
RI] and a message.
If only one tire is affected , the location of that
tire will be indicated.
The tire pressures must be stored in the Infotain­
ment system again each time the pressures
348
change (switching between partial and full load
pressure) or after changing or replacing a tire on
your vehicle ~
page 349. The tire pressure moni­
toring system only monitors the tire pressure you have stored. Refer to the tire pressure label for
the recommended tire pressure for your vehicle
~ page 340, fig . 272.
Tire tread circumference and vibration character­
istics can change and cause a tire pressure warn­
ing if:
- the tire pressure in one or more tires is too low
- the tires have structural damage
- the tire was replaced or the tire pressure was
changed and it was not stored
~ page 349
- tires that are only partially used are replaced
with new tires
Indicator lights
RI] -loss of pressure in at least one tire~,& .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires and
store the pressure again in the Infotainment sys­
tem
~ page 349.
m (Tire Pressure Monitoring System) Tire
pressure: malfunction! See owner's manual.
If
m appears after switching the ignition on or
while driving and the
RI] indicator light in the in­
strument cluster blinks for approximately one
minute and then stays on, there is system mal­
function. Try to store the correct tire pressures
~ page 349. In some cases, you must drive for
several minutes after storing the pressures until
the indicator light turns off . If the indicator light
does turn off or turns on again after a short peri­
od of time, drive to an authorized Audi dealer or
authorized Audi Service Facility immediately to
have the malfunction corrected.
& WARNING
- If the tire pressure indicator appears in the
display, reduce your speed immediately and
avoid any hard steering or braking maneu­
vers. Stop as soon as possible and check the
tires and their pressure.

-The driver is responsib le for maintaining the
correct tire pressure. You must c heck the
t ire pressure regu larly.
- Under certa in conditions (s uch as a sporty
dr iv ing style, winter cond itions o r unpaved
roads), the tire p ressure monitoring system
indicator may be de layed .
(D Tips
-The t ire press ure monitoring system can al­
so stop work ing when there is an ESC mal­
funct ion.
- Using snow chains may result in a system
malfunction.
- The t ire press ure monitoring system in your
A udi was calib rated with "A udi Orig inal
Tires"
<=)page 337. Using these t ires is rec­
omme nded .
Storing tire pressures
Applies to: vehicles with Tire Pressure Monitoring System in­
dicator
If the tire pressure changes or a tire is replaced,
it must be confirmed in the Infotainment sys ­
tem.
~ Make s ure before storing that the tire pressures
of a ll fou r tires meet the specified values and
are adapted to the load
Q page 340 .
~ Switch the ign ition on.
~ Se lect in the Infotainment system: ! MENUI but­
ton
> Vehicle > Service & checks > Tire pres­
sure monitoring > Store tire pressur e> Yes,
store now .
(D Tips
Do not store the tire press ures if snow chains
are insta lled.
Run-flat ti res
Applies to: vehicles with run-flat tires
A run-flat tire helps to maintain vehicle mobility
when there is a loss of pressure .
Cl ~ Run-flat t ires have re inforced sidewalls that pro-
~ tect the t i re if there is a loss of press ure. N ,-1 0
0
::r ' Wheels
If the t ire pressure monitoring system indicates a
l oss of pressure in one or severa l tires, yo u can
contin ue driving on run -flat tires fo r at least 20
miles (30 km). Drive to an authorized Audi dealer
or authorized Aud i Serv ice Facility immediately to
have the problem corrected .
Continuing to drive on run-flat tires is n o
longer possible if
- there is visible damage to the tires, such as
cracks in the sidewalls .
- strong vibrat ions are felt w hile driving, or the
tire beg ins to smoke due to a strong build-up of
heat .
- the t ire was heavi ly damaged, for example in an
accident There is a r isk that parts of the tire
tread will detach and damage important ve hi­
cle components .
- the E lectron ic Stab ilizat ion Control (ESC) is not
work ing or is cont inuously r unning .
- the t ire pressure monitoring system is not
work ing .
If it is no longer poss ible to continue driving de­
spite hav ing run-flat tires, see an author ized Audi
dealer or author ized Audi Service Fac ility for as­
s istance.
A WARNING
-
R un-f lat t ires may only be used on vehicles
that we re equipped with them at the fa ctory.
- The vehicle must have suspens ion designed
for run-flat tires and a facto ry-installed tire
p ress ure mo nitor ing syste m.
- I nco rrect use of r un-f lat t ires can lead to ve­
h icl e damage o r accidents. Contact an au­
thor ized A udi dealer or au thori zed A udi
Serv ice Facili ty to lear n if r un-f la t tir es may
be used on you r vehicle an d if so, which
ones.
- If r un-fla t ti re s are used, they m ust be in ­
stalled on all fo ur whee ls. Mix ing ti re types
is not permitted.
- If yo u have to drive when the tire press ure is
too low or there is no tire press ure, note the
following : .,..
349

Wheels
-Do not dr ive faste r than 50 mph (80 km/
h) because this increases the risk of an ac­
cident. Observe any laws specific to the
country where yo u are driv ing.
- Avoid full-th rottle accele ration, heavy
braking, and fast cornering, because this
increases the r isk of an accident .
- The vehicle may become more difficult to
control.
- See an autho rized Aud i deale r or a uthor­
ized Audi Service Fac ility for assistance if
the t ire is too heavily damaged.
- Have the faulty tires replaced and the rims
checked fo r damage by an author ized A udi
dealer or author ized Audi Service Facil ity.
- The driver is responsib le for the vehicle, fo r
correcting the t ire pressure and for rep lac­
ing faulty parts. Therefore, always adjus t
yo ur driv ing to the g iven s ituation .
(D Tips
-Audi Orig inal run-flat tires can be identified
by the "AOE" labeling on the tire sidewall.
- You can use the tire mob ility k it*
c:> page 357 on run-flat ti res.
350

Care and cl eaning
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when was h­
ing the underbody or the inside of the wheel
housings .
- After washing the vehicle, the braking effect may be delayed due to mo isture on the
brake rotors or ice in the winter . This in­
creases the risk of an acc ident . The brakes
must be d ried first w it h a few careful b rake
applications.
@ Note
- If you wash the ve hicle in an automatic car
wash, you must fold the exterior m irrors in
to reduce the risk of damage to the mirrors .
P ower folding exte rior m irrors* must o nly
be fo lded in and out using the powe r folding
f u nct io n.
- To reduce t he risk of damage to the rims
and t ires , compare the width be tween the
whee ls on your ve hicl e w it h t he distance be ­
tween the g uide rai ls in the car wash .
- To reduce t he risk of damage, compare the
height and width o f you r vehicle with the heig
ht and w idth of the inside o f the car
was h.
- T o red uce the risk of pa in t damage, do not
was h the vehicle in direct sun light .
- T o red uce the risk of d amage to the s urf ace,
do not use insect removing sponges, k itchen
sponges or similar items .
- Matte finish painted vehicle components:
- To reduce the r isk of damage to the sur-
face, do not use polis hing agents or hard
wax .
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnet ic
signs on vehicle parts painted with matte
finish paint . The paint cou ld be damaged
when the stickers or magnets are re­
moved .
@ For the sake of the environment
Only wash the ve hicle in facilities spec ia lly de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contaminated with o il from
ente ring the sewe r system.
Cleaning and care information
W hen clea ning and ca ring for ind ividua l vehicle
components, refer to the fo llowing tables . The
information contained there is simply recom­
m endations. Fo r qu estions or for compon ents t
h at are not listed, cons ult an autho rized Aud i
dealer or authorized A udi Service Fac ility. Also
fo llow the information fo und inc:>.&. .
Ext erior cleaning
Component Situation Solution
Windshield wiper
Deposits soft cloth with glass cleane r, c:> page 51
blades
Headlights /
Deposits Soft sponge with
a m ild soap solution a)
tail light s
S ensors /
Deposits Sensors: soft cloth with solvent -free cleaning solut ion
camera lenses Camera lenses: soft cloth w it h alcohol-free cleaning solu-
tion
Snow/ic e Hand brush/solv ent-free de -icing spray
Wheels Road salt Water
Brake dust Acid-free special cleaning solution
352