ignition AUDI R8 SPYDER 2011 Owner's Manual

The rear window can be extended comp lete ly
for cleaning. This is ca lled the cleaning posi­
tion.
E xte nding the re ar w indow into the wind
defl ector po siti on
~ Pull and hold the rear window switch
9 fig. 47.
~ Release the switch once the rear window has
reached the wind deflector position.
Exte nd ing th e rear w indow into th e
cleaning po sition
~ Pull and hold the rear window switch
9 fig . 47.
~ Release the switch once the rear window has
reached the wind deflector position .
~ Pull and hold the rear window switch again .
~ Pull and hold the convertible top switch
within one second
9 page 46, fig . 43.
R etra cting the re ar w indow
~ Press and hold the rear window sw itch until
the window has been retracted .
Ret racting the re ar wi ndow using the one­
touch funct ion
~ Press the rear window switch briefly . There
is no need to hold the switch.
The rear w indow can on ly be operated when
t he ignition is switched on.
The rear window can also be extended or re­
tracted when the convertib le top is closed.
.&_ WARNING
- Do not use the rear window to secure car­
go or other objects. This could result in
injury .
- Always pay attention and be careful
when extending or retracting the rear
window . It could cause injury by p inch­
ing .
@ Tips
-Keeping all of the w indows raised pro­
v ides the best wind protection.
Con vertible top 49
- The veh icle must be stationary to br ing
the rear window into the cleaning posi­
tion . The rear window will retract once
you begin dr iv ing.
Convertible top
emergency operation
General information
The convertible top can be closed by hand if
there is a malfunction .
First check if overload pro tection is active
~ page 47. If this is the case, the conve rtible
top w ill operate again after a short de lay . O th­
erwise the fo llowing steps must be completed
before closing the convertib le top:
~ Ac tiva te the pa rking brake.
~ Open the side w indows, if necessary.
~ Remove the key from the ignition.
Emergency loc king is no t intended for long­
te rm use o r long drives . The convertib le top
will not be completely waterproof after using
the emergency locking proced ure because the
seals wi ll not be seated correctly. Only close
the convertible top manually in an emergency .
Please see an au thor ized Audi R8 dea ler to
have the cause of the malfunction corrected .
.&_ WARNING
-The ignition must be sw itched off during
the entire closing p rocedure.
- When positioning the convertible top,
avoid contact with the supports or other
mov ing parts. Othe rwise you could p inch
your hands.
- Never d rive when the convert ible top is
not locked cor re ctly. The wind from d riv­
ing could cause the convertible top to
open . This can resu lt in injuries and dam­
age to the vehicle.
@ Tips
Have a second person assist whe n closing
the convert ible top. Opening the storage
bay lid and posi tioning the conve rtible top
is easier when a seco nd person is assisting.

50 Convertible top
Step 1: Retract the rear window
Fig. 48 Upper storage compartme nt: re mov ing the
cover
F ig. 49 Upper sto rage compartment: using the Allen
wrench as a crank to lower the rear win dow
M 0 N ... a,
... ... M 0
The rear window must be retracted in order to
close the convertible top. If the rear window
switch is not functioning ¢
page 48, the rear
window can be cranked .
.. Open the upper storage compartment be­
tween the seat backrests ¢
page 70 .
.. Remove the cover using the screwdriver
from the vehicle tool kit¢
fig. 48.
• Press the Allen wrench from the veh icle tool
kit firmly into the opening until it cl icks into
place ¢
fig. 49.
> Turn the bolt clockw ise u ntil the rear win­
dow is lowered .
Step 2: Release the pressure in the
hydraulic system
The pressure in the hydraulic system must be
re leased before the convertible top can be
closed.
.. Switch the ignition off .
.. Pull or press the convertible top switch
¢
page 46, fig. 43 for approximately 10 sec­
onds.
A WARNING
-
If convertib le top operation fails when
opening or closing the top, do not hold or
touch the supports or other moving parts
when releasing the pressure. The converti­
ble top will sink down and could pinch your
hands.
Step 3 : Open the convertible top storage
bay lid
Fig. SO E ng ine compartme nt: install ing the eme rgency
ope rat io n bolts
Fig. 51 Raising the sto rage bay lid and pulling it back
The engine compartment lid must be released
using the emergency procedure in order to re­
l ease the storage bay lid ¢
page 177.
Releasing the convertible top storage bay
lid
.. Turn the emergency operat ion bolts on the
left and right sides of the engine compart­
ment¢
fig. SO clockw ise using the open end
wrench from the vehicle too l kit until the
bolts are installed completely . The co nverti ­
ble top sto rage bay lid will raise app rox i­
mate ly 0,4 in (1 cm) from the vehicle when
t he bolts are install ed comp letely .
• Close the engine compartment lid
r=;, page 176.

Clear vision Lights
Switching the headlights on/off
Fig. 63 In str ume nt pa ne l: lig ht sw itc h (auto mat ic
head· a nd ta ill ig ht control)
Switching on the side marke r lights
... Turn the light switch to :oo::.
Switching on the headlights and high
beam
... Turn the light switch to §D.
.,. Push the h igh beam lever forwa rd towa rds
t h e instrument panel~
page 58 .
Sw itching off the lights
.,. Turn the light switch to 0 .
Sw itching on automatic head- and
taillight control
.,. Turn the light switch to AUTO ~ fig. 63 .
The headlig hts and tai lligh ts w ill come on au­
tomatically when the ignition is sw itche d on
and the light switch is in the position AU TO
(on ly in nig httime conditions). When switch·
ing off the ignit io n, the headlig hts wi ll go off
and only the side marker lights will remai n lit.
Daytime running lights
USA models: The daytime r unning lig hts will
come on a utomat ica lly when the ig nition is
sw itched on and the light switch is in the posi·
tion
AUTO (only in daylight conditions).
Canada models : Th e daytime runni ng lights
will come on a utomat ically when the ignition
is switched on and the light switch is in the
Clear vi sion 55
position 0 , AUTO (on ly in daylight conditions)
or ;oo :.
Automatic head- and taillight control
In the swi tch position AUTO the au tomati c
he ad- and t aillight con tro l is activ ated. Ligh t
senso rs ar e loca ted in t he i nside mir ro r h ous­
ing and co nstantly chec k the light cond itions
su rroundi ng the vehicle. If ambient bright­
ness fa lls below a factory set value (e .g. when
dr iv ing into a tunnel), the head- and tail lights
i ncl uding the license plate illuminati on are
automat ica lly t urned on . When ambient
brightness i ncreases aga in, the exte rnal ligh ts
ar e turned off aga in
c> &. . In the switch posi­
t ion
AUTO , the low beams are tur ned off when
th e ign ition is swi tched o ff. Th e rem aining
li gh ts are turned off when the key is ta ke n out
of the ignition lock.
W it h a utomat ic head- and taill igh t con trol,
t he h igh-beam fu nction is also ava ilable , bu t
with one rest ric t ion : If you have not sw itche d
the h igh beams back to low beams during a u­
tomat ic head light operat ion (for examp le, af­
ter driving through a tunnel), on ly the low
beams come on the next time automatic
headlig hts are switched on. To use the high
beams, yo u fi rst have to pull the h igh beam
lever back and then push the lever forwa rd
agam .
The side ma rke r lights a nd headlights ca n be
sw itc hed on manually by turn ing the light
swi tc h to the des ired pos ition .
Light sensor malfunction
If there is a light sensor ma lfunction, the
symbol
II comes on in the display . For safety
reasons, the low beams are tu rned on perma­
nently with t he sw itch in
AUTO . However, you
can con tinue to tu rn the lights on and off us­
in g t he light switch . Have t he ligh t sensor
c h eck ed as soon a s possib le a t an au thorized
A udi dealer.
Coming home/leaving home function
The function is sw itched on when the sw itch is
i n the
AUTO pos ition and th e funct ion is liJJ,,

56 Clear vision
shown as active in the driver information
system.
The
coming home function illuminates the
area around the vehicle when the ignition is
switched off and the driver's door is opened.
The length of time the lights remain on can be
set in the menu display
(Lights> Exterior
lights> coming home) .
The leaving home function illuminates the
area around the vehicle when unlocking it.
.&_ WARNING
- Never use daytime running lights to see
where you are going. They are not bright enough and will not let you see far
enough ahead for safety, especially at dusk or when it is dark. Be aware of
changes in outside light conditions when
you are driving and respond by switching
on your low beams.
- Automatic head- and taillight control is
only intended to assist the driver. This
feature does not relieve the driver of his
responsibility to check the headlights
and to turn them on manually according
to the current light and visibility condi­
tions. For example, fog and rain cannot be detected by the light sensors. Conse­
quently, always switch the headlights on
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists.
-Always turn on the headlights so that you can see ahead and so that others can see your car from the back.
(D Tips
- Always observe the specific local regula­
tions for your area when to use your
lights .
- Turn on low beams as evening ap­
proaches or in conditions of poor visibili­
ty.
- Do not attach stickers to the windshield
in front of the sensors as this can disable the automatic head- and
taillight control
and the automatic glare-dimming of the
rearview mirror(s)*.
- If you
remove the ignition from the igni­
tion lock while the headlights are still
on, a buzzer will sound as long as the
driver's door is open to remind you to
turn off the lights.
- In the AUTO mode, the low beams are
turned off when the ignition is turned
off. The remaining lights are turned off
when the key is taken out of the ignition .
- In cool or damp weather conditions the
headlights may fog
over temporarily on
the inside.
- The critical factor is the temperature
difference between the interior and the
exterior of the headlight lens.
- With the main beams switched on, the
light-emitting area will be free of con­
densation after a short time, however
the edges of the glass may still be fog­
ged.
- This physical phenomenon has no ef­
fect on the life of your vehicle's light­
ing system.
Instrument panel illumination
The illumination of the instruments, displays
and the center console can be adjusted.
Fig. 64 Instrument panel illumination
You regulate the brightness of the instru­
ments with the left thumbwheel
(-'1· ~ fig. 64.
A phototransistor integrated into the instru­
ment cluster controls the illumination of the
needles in it. When the lights are switched on,
the lighting for the center console and the
llll>

instruments (needles and dials) is automati­
cally adjusted to ambient conditions. The driv­
er can a lso ad just the brightness of the light­
ing.
Ignition ON , light switch at @
With the ignition swi tched O N, the glow of in­
strument needles
can be adjusted to appear
brighter or dimmer.
Ignition ON , light switch at coo; or gD .
With the l igh ts sw itched on, the bright ness of
in str ument cluster (i.e. needles, g auges and
disp lays) and center console i llumination can
be adjusted .
(D Note
The inst rument cl uster and cente r console
illum ination (ga uges and needles) comes
on when you switch on the ignition and the
vehicle headlights are off. Be aware of t he
following difference between mode ls built
to US or Canadian specifications:
- USA models: illumination of the inst ru­
ment cluster (ga uges and needles), das h
and center console around the gearsh ift
l ever is controlled by a light senso r locat­
ed in the instrument panel. The instru­
m ent pane l illumination will a utomat i­
call y become dimmer as t he day ligh t
fades away and eventually will go o ut
com plete ly when o utside light is ve ry
l ow. This is to rem ind you, the driver, to
switch on the headlights before it gets
too dark .
- Canada mode ls: instrument panel i llum i­
nat ion will stay bright regard less of the
i ntensity of amb ient light. Always be
aware of c hanges in outside light cond i­
t ions wh ile you are driving. Respond in
time to fadi ng daylight by tu rning the
l ight sw itch to posit ion
io (or "AUTO" if
you r ca r is equ ipped with th is featu re) to
turn on your hea dligh ts. Clear vi
sion 5 7
Emergency flasher
The emergency flasher makes other motorists
aware that you or your vehicle are in an emer­
gency situation .
Fig. 65 Cent er consol e: eme rge ncy flas he r sw itc h
.,. Press the switc h l!J ~ fig. 65 to switch t he
emergency flasher on or off.
When the eme rgency f las her is on, all four
turn s ignal b link at t he same time . Th e turn
signal indicato r lights
1111 in t he instrument
cluster, as well as the light in the eme rgency
flasher switch ~ blink likew ise . The emergen­
cy flasher also works when the ignition is
switched off .
The eme rgency flasher will automatically
switch on if you are in an accident where the
airbag has deployed.
@ Tips
You sho uld switch on the emergency flash­
er when:
- you a re the last ve hicle standing in a t ra f­
fic jam so that any other vehicles coming
can see you, or when
- yo ur vehicle has bro ken dow n or you are
in an eme rgency s ituation, or when
- yo ur vehicle is be ing towed by a tow
truck or if you are towing another vehicle
behind you.

58 Clear vis ion
Turn signals and high beam lever
The lever is used to operate the turn signals
and the high beam as well as the headlight
flasher .
Fig. 66 Turn s igna l and high beam lever
The turn s ignal and high beam leve r has the
following functions:
Turn signals ¢ c::>
"" Lift the lever up all the way¢ fig. 66 to use
the right turn signals @, or push the lever
down all the way to use the left turn signals
@ .
""Move the lever (up or down) just to the point
of resistance to use the turn signals for as
l ong as you need them, for example when
changing lanes.
"" Briefly move the lever up or down just to the
po int of resistance and then release it to
flash the turn signals
three times in succes­
sion.
T his Convenience turn signal function
must be activated in the menu display
¢ page 24.
High beam [D
"" Push the lever forward @ to switch on the
high beam.
"" Pull the lever back towards you to switch off
the high beam.
Headlight flasher [D
"" Pull the lever toward the steering wheel @
to use the headlight flasher.
Notes on these features
- The turn signals only work with the ignition
switched on. The indicator lights
II or II in
t he instrument cluster¢
page 14 also blink. - After you have turned a corner, the turn sig­
na l switches off automatically .
- The
high beam works only when the head­
lights are on . The indicator light. in the
instrument cluster illuminates when the
high beams are on.
- The
headlight flasher works on ly as long as
you ho ld the lever -even if there a re no
lights switched on. The indicator light . in
the instrument cluster illuminates when you
use the headlight flasher.
(D Note
Do not use the high beam or headlight
flasher if you know that these could be
blinding oncoming traffic.
Interior Lights
Interior light s
The interior lights include the reading lights
for the driver and the front passenger.
Fig. 67 Sect ion from headliner: Interior lights
Activating door contact circuit
.,. Press the button@. The LED in the button
illumi nates.
Deactivating door contact circuit
"" Press the button @. The LED in the button
goes out.
Front reading lights ~
"" Press one of the switches @ to turn the
r ight or left reading l ight on or off.
With the door contact circuit, the interior
lights tur n on as soon as you unlock the vehi-
cle or open the doors. The interior lights are
Ill>

also turned on when the ignition key is re­moved. The lights turn off about 30 seconds
after the doors are closed. When the vehicle is
l ocked or when the ignit ion is turned on, the
interior light s are turned off .
When a door is open, the interior lights are
turned off after abo ut 10 m inutes to prevent
battery draining .
The brightness of the lights is controlled a u­
tomatically by a dimmer when they are sw itched on and off.
Luggage compartment light
The light is located on the right side of the
luggage compartment .
These lights come on automatically when the
front lid is opened. The lights turn off auto­
matically if the lid is left open for more then
10 minutes.
Vision
Sun visors
Using the sun visors makes driving safer.
Fi g. 68 Sun v isor
The vanity mirrors in the sun visors are eq uip­
ped with covers. Clear vi
sion 59
Wiper and washer
system
Windshield wiper
The windshield wiper lever controls both the
windshield wipers and the washer system.
F ig . 69 W ipe r leve r
The windshield wiper lever ¢ fig. 69 has the
follow ing positions:
Intermittent w iping ~l (act ivating r ain
sen sor)
.,. Move the lever up to position (D .
.,. Move the switch @to set the duration of
the wipe intervals or to adjust the sensitivity
of the light/ra in sensor .
Lo w wiper spe ed
.,. Move the lever up to position @.
High wiper speed
.,. Move the leve r up to posit ion @.
One-touch wiping
.,. Move the lever to position ©, when you
want to wipe the windsh ield
briefly .
Automatic wip er/ wa sh er
.,. Pull the lever to position ® (toward the
steering whee l) and hold .
.,. Release the lever. The washer system stops
and the wipers continue to operate for
about 4 seconds . Different numbers of wipe
cycles are performed depending on how
long the lever is he ld.
Turning off the w ipe rs
.,. Move the lever back to position @ .

60 Clear v is ion
Moving w iper blades to the service
posit ion
.. Do not lift the wiper arms away from the
glass when they are in their parked position;
this would damage the paint on the front
lid .
.. When there is a risk of frost, make sure that
the wiper b lades are not frozen to the wind­
shield .
.. Move wipe r blades to the se rvice posit ion
¢page 61.
The windshield wipers and washer on ly work
when the ignition is turned on.
To reduce the sensit iv ity of the sensor, move
switch @down . To increase the sens itiv ity,
move the switch up. The higher you adjust the
sens itivity, the faste r th e sensor will react
when it senses moisture on the w indshield.
The pauses between w iper turns depend not
on ly on the sensitivity setting, but on the ve ­
hicle speed as well.
Du ring a temporary stop, e.g . at a t raff ic sig­
na l, the set wipe r speed is automatically re­
duced by one stage.
When the igni tion is tu rned on, the washer
jets are heated.
_& WARNING
- Wipe r blades a re cruc ial for safe driving!
Only when they are in good cond ition are
they able to clear the windows properly
to provide uncompromising visibility.
Worn or damaged wiper blades are a safety hazard ¢
page 61, Replacing
front wiper blades!
- The light/ra in sensor is only des igned to
assist and support the dr iver .
It remains
entirely the d river 's responsibility to
mon itor outs ide weather conditions and
to manually activate the w ipers as soon
as rain o r dri zzle red uces visibi lity
thro ugh t he windshie ld.
- T he windshie ld must not be treated with
water-repe llent materials. They can in­
crease glare under poor visib ility condi­
tions such as wetness, darkness, or when the s
un is low on the horizon . In addi­
tion, they can cause the w indshield w ip­
ers to chatter .
(D Note
In freezing or near freezing conditions:
- Always check that the w iper b lades are
not frozen to the g lass before you turn
the wipers on . Loosen a wiper blade
wh ich is frozen in place before operating
the wipers to prevent damage to the
w iper blade or the wiper motor.
- Do not use the w ipers to clear a frosted
window. Us ing the wipers as a conven­
ient ice scraper will destroy the wiper
blades .
- Before you take your veh icle to an auto­
matic car wash, make sure you have the
w indshield w iper system switched off
(lever in position 0), otherwise the w ind­
shield w iper system could get damaged
in the car wash if it should suddenly
come on .
(D Tips
-The windshie ld w ipers are switched off
w hen the ignit ion is turned off. Act ivate
t he winds hield wipers after the igni tion
is switched back on by moving the wind­
shield wiper lever to any position.
- Worn or d irty windshield wipe r blades
cause smearing, which can affect the op­
eration of the light/rain sensor . Check
the cond ition of your windsh ield wiper
blades regularly.
- When the wipers are switched on man­
ually and in ra in cond itions, the auto­
matic headlights turn on
¢ page 55 or
off during the day when the wipers are
no longer operating . The automat ic
head lights fu nction is avai lab le in this
case on ly w hen the light switch is in the
"A UTO" posit ion ¢
page 55, fig. 63.
-Make su re the washer fluid reservoir is
t opped off before goi ng on a long tr ip.
Look up ¢
page 188 for checking and
filling the washe r containe r.

-If you switch off the ignition w ith the
windshield wiper lever still in the inter­
val w ipe pos ition and then come back a
while later and dr ive off , the rain sensor
will reactivate itself after the vehicle
speed has exceeded 4 mph (6 km/h) .
Service position
It is only possible to change wiper blades if
you move the wiper arms to the service posi­
tion .
In order to use the windshield wipers, the
front lid must be comp letely closed.
Moving w ipe r blade s to the service
position
.. When there is a risk of frost, make sure that
the wiper b lades are no t frozen to the wind­
shield .
.. Switch the ign ition on .
.. Move the wiper lever to pos ition
0
c::> page 59, fig. 69 .
.. Press the I RESE T I button unt il the Display
type
menu appears in the Driver Informa­
tion System display .
.. Using the rocker switch and the
!RESET I b ut­
ton, select the
Set > Wiper s > Front > Serv ­
ic e position on
function . The wind sh ield
wiper arms move to the service pos it ion.
Moving w ipe r blade s to park po siti on
.. Make certain that the wiper arms are ly ing
against the w indshie ld .
.. Switch the ignition on and move the wipe r
lever from position
O to 4 c::> page 59 ,
fig. 69. The wiper arms will move back to
t h e park pos ition .
(D Note
Never drive your vehicle when the wind­
shield w iper arms are in the service pos i­
tion and pulled away from the windshie ld.
When you dr ive faster than
4 mp h (6 km/
h), the w iper arms a utomat ica lly re turn to
t he par k position and could ca use pa int
d amage to the front lid!
Clear vi sion 61
@ Tips
- Yo u can also turn on t he service position,
for example, if yo u want to protect the
w indshield from icing by using a cover.
- Th e service posit io n moves to
off auto­
matically when you operate the wind­
shield wiper lever, or speed exceeds
4 mph (6 km/h).
Replacing front wiper blades
Wiper blades in good condition help keep the
windshield clear.
Fi g. 70 Unl atching w ipe r blade s
Fig. 71 Re mov ing w iper b lades
Removing the wiper blade
.. Move the wipers to the service pos it ion
c::> page 61.
.. Fold the windsh ie ld w iper arm away from
the glass .
N 0
i ,:. .., m
.. On the upper end of the wiper arm at the
corr uga tion, squeeze the p lastic ret ainer to­
gethe r on both s ides in the direction of the
arrow
c::> fig. 70.
.. Rotate the w iper b lade in the direction of
the arrow @
c::> fig. 71 away from the wiper
arm .
.. Lift the wiper b lade off in the d irection of
t he arrow @.

_& WARNING
Broken glass of automatic dimming mirror
can cause electrolyte fluid leakage. Elec­
trolyte fluid can irritate sk in, eyes, and res­
piratory system .
- Repeated or prolonged exposure to elec­ trolyte can cause ir ritation to the resp ira­
tory system, espec ially among people
with asthma or other respiratory condi­
ti ons. Get fres h ai r i mmedia tely by leav­
ing the vehicle or, if that is not possible,
open windows and doors all the way.
- If electrolyte gets into the eyes, flush
them thoro ughly with large amounts of
clean water for at least 15 min utes;
med ica l attent ion is recommended.
- If e lectrolyte contacts sk in, f lush affect­
ed area with clean water for at least 15
minutes and then wash affected area
with soap and water; medical attention
is recommended . T horoughly wash af­
fected clothing and shoes before reuse .
- If swallowed and person is conscious,
rinse mouth w ith water for at least 15
min utes . Do not i nd uce vom it in g unless
inst ructed to do so by medical professio­
nal. Get medical atten tion immediately.
CD Note
liquid electro lyte leaked from a b roken
m irror glass will damage any p lastic surfa­
ces it comes in contact with. Clean up spil­
led electro lyte immediately wi th clear wa ­
t er and a sponge.
(D Tips
- If yo u switch off the automatic dim·
ming function on th e in sid e mirror , au ­
t o mati c dimming of the out sid e mirror s
w ill likewi se be di sabled .
-Check to make sure there are no objects
preventing light from reaching the inside
mirro r.
- Do no t attach any sticke rs to the wind ­
sh ield in front of t he two light sensors,
as this would interfere with both the au ­
tomatic operation of the headlights and
Clear vi sion 63
the a utomatic dimming of the inside
mirror(s) .
Outside mirrors
The outsid e mirrors ar e electrically adjusted .
Fig. 73 Forward sect io n of dr iv er's armrest: powe r mir ­
ro r control s
Adjusting the outside mirrors
.,. Turn the adjust ing knob to position © (driv­
er 's s ide) or in pos ition ® (passenger side)
r::!) fig. 73.
... Press the knob in the appropriate dire ction
to move the mi rror surface so that yo u have
a good view to the rear .
Heated mirrors
... Tu rn the knob to position @.
Folding both out side mirro rs flat*
.,. Turn the knob to @.
Depend ing on the outside temperature, the
mirror surfaces are heated until the ignition is
switched off - even if the knob is no longer in
pos ition @.
You are we ll-advised to fold* the outside mir­
rors in maneuvering in tight spaces or when
leaving the car parked close to other vehicles.
CD Note
- Curved (i .e. convex) mirror surfaces in­
crease yo ur field of view. Remember that
vehicles or other objects will appear smaller and farther away than when
seen in a flat m irror . If you use this mir­
ror to estimate distances of following ve-
hicles when chang ing lanes, you could ..,.