engine AUDI R8 SPYDER 2011 Repair Manual

182 Checking and filling
may seriously degrade the corros ion pro­
tection. The resu lting damage can cause
l oss of coo lant and subsequent ly lead to
se rious engine damage.
- The coolant additive
Gl2++ must not be
mixed w it h other coo lant add itives.
- Do not add any type of radiator leak sea l­
ant to your ve hicle's engine coo lant.
Adding rad iator repair fluid may adve rse­
ly affect the function and performance of
your cooling system and could result in
damage not covered by your New Vehicle
Limited Wa rranty.
Checking the engine coolant level
Proceed carefully when checking the coolant .
Fig. 145 Convert ible top: serv ice pos iti on
Fig. 146 Convert ible top storage bay: coo la n t expa n­
s ion tank
Before you check anything i n the eng ine com­
pa rtment,
alway s read and heed all WARN­
INGS c:::> ,&. in Working in the engine compart ­
ment on page 175.
T he coolant expa nsion tank is located i n the
r ight s ide of the co nvertib le top s to rage bay
under the ro und metal cover
c::>fig. 146. The
conver tible top must be in the servi ce position
to check the coolan t leve l
c:::> fig. 145 .
Bringing the closed convertible top into
the service position
.,. Switch t he ignition on.
.,. Pull and ho ld the convertib le top switch.
.,. Press and hold the rear window switc h too
until the convert ible top moves into the
service pos ition
c:::> fig. 145 .
Bringing th e open convertible to into the
service position
.,. Switch th e ignit ion on.
.,. Press and hold the convert ible top switch.
.,. Press and hold the rea r window switc h too
until t he convert ible top moves into the
service pos it ion
c:::> fig. 145.
Opening the coolant expansion tank cover
.,. Stop the engine a nd a llow it to cool.
.,. Switch t he ignit ion off .
.,. Carefully remove the bolts in the cover
(D
using a sc rewd river and remov e th e cover.
The coolan t rese rvo ir i s located be low
c:::> fig. 146 .
Checking the engine coolant level
.,. Place a rag or cloth on the cap of the coolant
e xpansion tank a nd turn the cap
carefully to
the left ( counte r-cloc kw ise)
c:::> .&_ .
.,. Read the coolan t leve l inside the coolan t ex ­
pa nsion tank
c:::> fig. 1 46. W it h a co ld eng ine,
it must be above the "min" mark . With a hot
engine, it can be a litt le above the indicated
range.
T o obtain an acc urate reading, the engine
must be sw itched off.
T he e xpansion ta nk in your vehicle is eq uipped
with an electr ic coo lant level senso r
c::> page 32. We s till rec om mend you check the
coolant leve l from time to time.
Coolant loss
Coolant loss may indicate a leak in the cooling
system. In t he eve nt of cool ant los s, the cool­
ing system should be inspec ted immedi ately
by your a uthorized Audi dea ler . I t is not
eno ugh mere ly to a dd coo lant .
ll-

In a se ale d system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheat ing.
A WARNING
- The cooling system is under press ure. Do
not open the cap of the coolant expan­
sion tank when the eng ine is hot. You
risk being scalded .
- The coo lant add itive, and therefore the
coolant itse lf, is hazardous to health.
Keep the coolant additive in the origina l
co nta iner out of the reach of children.
It
is a poison hazard.
CD Note
Do not add any type of rad iator leak seal ­
ant to your vehicle's eng ine coolant. Add­
ing radiator repair f luid may adve rsely af­
fect the fu nction and performance of your
coo ling system and could res ult in damage
not covere d by your New Vehicle Limited
Warranty .
Adding coolant
Before you check anything in the engine com­
partment,
always read and heed all WARN­
INGS ¢ & in Working in the engine compart­
ment on page 175 .
.. Add coolant .
.. Tw ist the cap on again
t ightly.
.. Tighte n the cap (D ¢ page 182, fig. 146
again .
Replacement engine coolant must conform to
exact specifications ¢
page 181, Coolant. If
the coolant additive Gl2++ is not available in
an emergency, you must not add any other ad­
d itive . In th is case, use only water and restore
the co rrec t mix ratio wi th the specified cool­
ant add itive as soon as possib le.
Always use
new engine coolant when ref illing .
Do not fill coolant above the " MAX" mark. Ex­
cess coolant will be forced out through the p ressure relief valve i n the cap when the en ­
g ine becomes hot .
Checking and fillin g 183
With a major loss of coolant, you shou ld add
the coolant only when the engine has
cooled.
In this way you prevent engine damage.
A WARNING
- The cooling system is unde r pressure and
can get very hot. Reduce the risk of
scalding from hot coolant by followi ng
these steps .
- Turn off t he engine and allow it to coo l
down.
- Protect you r fa ce, hands and arms from
escaping fluid and steam by covering
the cap with a large, th ic k rag.
- Turn the cap s lowly and very carefully
in a counter -clockwise direction while
applying light, downward pressure on
the top
of the cap.
- To avoid being bu rned, do not spill an­
tifreeze or coolant on the ex haust sys ­
tem or hot engine pa rts. Under certain
cond itions, the ethylene glycol in en­
gine coolant can catch fire .
- Antifreeze is poisonous . Always store an­
tifreeze in its origina l container and well
out of the reach of children .
- If you dra in the coo lant, it m ust be
caught and safely stored in a proper con­
taine r clearly marked " poison" .
CD Note
- Coolant pollutes the environment and
cou ld cause an engine fire. Excess cool­
ant will be forced out through the pres­
sure relief valve in the cap w hen the en­
gine becomes hot .
- If, in an eme rgency, o nly wate r can be
added, the co rrec t ratio between wa ter
and antifreez e
¢page 181 must be re­
stored as soon as poss ible.
@) For the sake of the environment
D ra ined coola nt sho uld not be reused. Al­
ways d ispose of used coolant while observ­
i ng a ll environmental regula tions. •
•

disconnect the battery negative terminal. Oc­
casionally charge a disconnected battery.
Winter operation
The cold time of year places a special strain on
the battery, resulting in reduced starting pow­
er. So before the cold weather starts, have the battery inspected and charged as necessary.
A WARNING
- All work on the battery requires technical
knowledge. Please contact an authorized
Audi dealer or another authorized facility
for questions about the battery - danger of acid burns and explosion hazard!
- The battery must not be opened! Do not
try to change the battery's liquid level,
otherwise detonating gas will escape
from the battery - explosion hazard!
Working on the battery
Always wear eye protection.
Battery acid contains sulfuric
acid. Always wear gloves and eye
protection.
No
- sparks
- flames
- smoking.
When a battery is charged, it pro­
duces hydrogen gas which is ex­ plosive and could cause personal
injury.
Always keep the battery well out
of reach of children.
The following WARNINGS are very important
when working on the battery:
A WARNING
Whenever working on the battery or on
the electrical system, there is the risk of
injury, accident and even fire. Read and
heed the following WARNINGS:
-
Checking and filling 185
- Always wear eye protection. Do not let
battery acid or any lead particles get on
your skin or clothing. Shield your eyes. Explosive gases can cause blindness or
other injury.
- Battery acid contains sulfuric acid. Sulfu­
ric acid can cause blindness and severe
burns.
- Always wear gloves and eye protection.
Do not tilt the battery because acid
could leak out of the ventilation open­
ings.
- If you get battery acid in your eyes or
on your skin, immediately rinse with
cold water for several minutes and get
medical attention.
- If you should ingest any battery acid,
seek medical attention immediately.
- Do not expose the battery to an open
flame, electric sparks or an open light.
- Do not smoke.
- Do not interchange the positive and neg- ative cables.
- When working on the battery, be sure
not to short-circuit the terminals with
tools or other metal objects. This would cause the battery to heat up very quickly,
which could lead to damage or explosion and personal injury.
- When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal injury.
- Always keep the battery well out of the
reach of children.
- Before work is done on the electrical sys­
tem, disconnect the negative ground ca­
ble.
- Before performing any work on the elec­
trical system, switch off the engine and
ignition as well as any electrical equip­
ment. The negative cable on the battery
must be disconnected.
If you are just go­
ing to replace a light bulb, then it is
enough to switch off the lights.
- Before disconnecting the battery, switch
off the anti-theft alarm system! Other­
wise you will set off the alarm. •
•

186 Checking and filling
-When disconnecting the battery, first
disconnect the negative cable and then
the positive cable.
- Before reconnecting the battery, make
sure all electrical consumers are switch­ ed off. Reconnect the positive cable first
and then the negative cable. Never inter­
change the cables -this could start a fire!
- Never charge a frozen or a thawed-out
battery. It could explode!
If a battery has
frozen, then it must be replaced. A dis­
charged battery can freeze over at 32 °F
(0 °C).
-Make sure the vent hose is always attach­
ed to the opening on the side of the bat­
tery.
- Never use batteries which are damaged.
Danger of explosion! Always replace a
damaged battery .
.&, WARNING
California Proposition
65 Warning:
- Battery posts, terminals and related ac­
cessories contain lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive problems. Wash hands after han­
dling.
(D Note
- Do not disconnect the vehicle battery
when the ignition is switched on or when
the engine is running, otherwise, you will
damage electronic components in the
electrical system.
- If your vehicle is going to stand for a
long period of time without being driven,
protect the battery from "freezing", oth­
erwise it will be damaged and will then have to be replaced. Charging the battery
Connections for
charging the battery are lo­
cated in the luggage compartment.
Fig. 147 L uggage compartment: battery cover
Fig. 148 Luggage compartment: connectors for a
charger and jump start cables
Do not connect the negative cable directly to
the negative terminal on the battery. Connect
it to a
jump start pin instead c:, fig. 148.
.,. Always read and heed all WARNINGS c:, A
in Working on the battery on page 185 and
¢ A -
... Switch off the ignition and all electrical con­
sumers .
.,. Open the luggage compartment lid
c:>page42 .
.,. Remove the battery cover c:, fig. 147.
.,. Connect the terminal clamps from the
charger to the battery terminal (red= "posi­
tive") and the jump start pin
c:, fig. 148
(black or brown= "negative") as specified.
.,. Only now plug the mains lead for the charg­
ing equipment into the wall outlet and turn
it on .
.,. When the battery is fully charged: Turn the
charging equipment off and remove the
mains lead from the wall outlet .
.,. Now remove the clamps for the charging
equipment.

~ Install the battery cover.
~ Close the luggage compartment lid
¢page 42.
When charging at low voltages (e.g. with a
trickle charger), the battery cables do not
have to be disconnected first. Before charging
at
high voltages, i.e. "fast charging", you
must disconnect both cables. In either case,
follow the instructions from the manufacturer
of the charger .
Fastcharging a battery is
dangerous ¢.&. in
Working on the battery on page 185 .
It re­
quires special charging equipment and the knowledge to go with it. We recommend hav ­
ing your battery fast charged only by a quali­
fied workshop.
A discharged battery can
freeze at tempera­
tures of only 32 °F (0 °C) . Allow a frozen bat ­
tery to thaw completely before attempting to
charge it¢ ,&. . However, we recommend not
using a thawed battery again because the bat­
tery casing can be cracked due to ice forma­
tion and can leak battery acid.
Do not open the battery caps when charging
the battery.
_& WARNING
-
Charging a battery can be dangerous.
- Never charge a frozen battery .
It may ex­
plode because of gas trapped in the ice.
Allow a frozen battery to thaw out first.
- Do not reuse batteries which were fro­
zen. The battery housing may have
cracked and weakened when the battery
froze.
- Charge the battery in a well ventilated
area. Keep away from open flame or elec­
trical spark. Do not smoke. Hydrogen gas
generated by the battery is explosive.
- To reduce the danger of explosion , never
connect or disconnect charger cables
while the charger is operating.
- Fast charging a battery is dangerous and
should only be attempted by a compe­
tent technician with the proper equip­ ment.
Checking and filling 187
- Battery acid that may spill during charg­
ing should be washed off with a solution
of warm water and baking soda to neu­
tralize the acid .
@ Note
Never use a fast charger as a booster to
start the engine. This will seriously dam­
age sensitive electronic components, such
as control units, relays, radio, etc ., as well
as the battery charger .
(D Tips
-The vehicle battery must not be charged
with a standard small charger that plugs
into the cigarette lighter or outlet .
- Only charge the battery through the con­
nections in the luggage compartment.
Replacing the battery
The new battery must have the same specifi­
cations as the old one.
Your vehicle is equipped with an intelligent
energy management system for distributing
electricity ¢
page 155. The battery charges
better in vehicles with the energy manage­
ment system than in vehicles without the sys­
tem. To ensure that the additional power is
available after replacing the battery , replacing
with the same type of battery from the same
manufacturer (like the battery that was deliv­
ered with the vehicle) is recommended. An au­
thori zed dealer mus t code the battery in the
energy management control module .
T he new battery must have the same capacity,
voltage (12 volts), current and design and it
must be sealed with plugs. The battery must
conform to the standards TL 825 06 (from Oc ­
tober 2006) and VW 7 50 73 (from August 2001).
Since the vehicle battery is difficult to reach,
we recommend having the battery replaced by
an authorized Audi R8 dealer or other quali-
fied workshop . ..,. •
•

188 Checking and filling
(D Note
-Your vehicle is equipped with a specia l
battery. Installing a different type of
battery can cause prob lems in the vehi­
cle electrical system. When replacing the
vehicle battery, always install one with
the same spec ificat ions as the original
batte ry .
- Make sure that the gas venting hose is
always connected to the o riginal open ing
on the battery side. Otherw ise gasses or
ba tte ry acid cou ld leak out .
- Battery ho lder and term inals a lways
have to be secured cor rectly.
- Read and follow the warnings under
9 page 185, Working on the battery be­
fore performing any work on the batte ry.
@ For the sake of the environment
Because of the problem of proper disposal
of a battery, we recommend your author­
ized Audi dealer change the batte ry for
you . Batter ies contain s ulf uric ac id and
lead and must always be disposed of prop­
erly in compliance with all environmenta l
reg ulations. D isposing of vehicle batteries
improperly is very dangerous to the envi­
ronment. Make sure that the removed bat­
tery ca nnot overbalance, otherwise sulfu­
r ic acid might escape!
Windshield washer
container
Fig. 149 Luggage co m pa rtment : W inds hield washer
fl uid reservo ir
T he windshield washer container O is located
in the luggag e compartment. You can find the
reservo ir
c a pacit y in the table in c::> page 229.
Clean water should be used when filling up. If
possible, use soft water to prevent scaling on
the washer jets . Always add a glass cleaner
solution (with frost protection in the winter) .
(D Note
-Do not mix engine coolant antifreeze or
any other additives to fill up the wind­
shield washer reservoir.
- Do not use g lass cleaners conta ining
pai nt so lvent; you risk damaging the
paint.

194 Tire s and wheel s
The table be low lists the recommended cold
tire inflation pressures for the Audi model
covered by your Owner's Literature at the vehi- cle's capacity weight and the tire sizes instal­
led on the respective models as original
equipment, or as a factory option.
Engine
(dis­
place­
ment in Tire designation
Tire pressure front Tire pressure rear
normal load full load normal load full load condition condition condition condition
liter )
a -cylin­
der
4 .2
inder
5.2 235
/3 5 R1 9 9 1 V
XL
295 /30 R19 100V X L
305 /30 R1 9 10 2V X L
235 /35 R19 91 V X L
295 /30 R1 9 100V XL
305 /30 R19 102V X L
XL= reinf orc ed
PSI
45
Because tec hnical changes may be made to
vehicle equ ipment dur ing the model yea r, a l­
ways compare the tire size designation on the
tire pressure labe l on you r vehi cle w it h the
tires on your vehicle. Make s ure that the ti re
size information on the veh icle label is the
same as the size of the tires on the vehicle.
This is especially important if the vehicle be­
longs to someone else or you bought the vehi­
cle with different rims/tires or you bought the
vehicle as a previously owned vehicle.
Remember, your safety and that of your pas­
sengers also depends on mak ing sure that
load limits are not exceeded. Vehicle load in­
cludes everybody and everything in and on the
veh icle . These load lim its are technically refer­
red to as the vehicle's G ross Vehicle We ight
Rati ng ("GVWR"). The G ross Ax le Weight Rat­
i ng ("GAWR") is the max imum load that can
be app lied at each o f the veh icle's two axles.
The G ross Vehicle Weight Rating and the
Gross Axle Weight Rating are listed on the
safety compliance stic ker labe l located either
on the driver's side B-pillar. The tire pressure
labe l on your Audi lists the maximum com­
b ined weight of all of the occupants and lug­
gage or other cargo that the veh icle can carry.
For the location of the tire pressure label
¢ fig. 15 0 .
kPA PSI kPA PSI
310 45 310
41
41
kPA PSI
280 41
280 41
kPA
280
280
280
280
.&_ WARNING
Overloading a vehicle can cause loss of ve­
h icle cont ro l, a crash o r other accident, se ­
r ious pe rsonal injury, and even death.
- Ca rrying more we igh t than your veh icle
was designed to carry wi ll prevent the
vehicle from handling properly and in­
crease the risk of a loss of vehicle con­
trol.
- The brakes on a vehicle that has been
overloaded may not be able to stop the
veh icle w ith in a safe distance.
- Tires on a vehicle that has been over load­
ed can fail s uddenly ca us ing loss of con­
trol and a crash.
.&_ WARNING
- Incorrect tire pressures and/or underin­
flation can lead to a serious or fatal acci­
dent.
- Inco rrect tire pressures and/or underin­
f lation cause increased tire wear and can
affect the handling of the vehicle.
- Inco rrect tire pressures and/or underin­
f lation can a lso lead to s udden t ire fail­
ure, including a blowout and sudden de­
flation, ca using loss of veh icle cont ro l.

Consumer Information
Warranty coverages
Your Audi is covered by the following war­
ranties :
-New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfo-
ration
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding yo ur warran ­
ties can be found in your
Warranty & Mainte­
nance booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulations in the United States
and Canada require that automobiles meet
specific emission regulations and safety
standards. Therefore, veh icles built for the
U.S.A. and Canada differ from vehicles sold in
other countries .
I f you p lan to take your vehicle outside the
continental limits of the United States or Can­
ada, there is the possibility that
- unleaded fuels for vehicles with cata lytic
converter may not be available;
- fuel may have a considerably lower octane
rating . Improper fuel may cause engine
damage;
- service may be inadequate due to lack of
proper service facilities, tools or testing
equipment;
- replacement parts may not be readily availa­
ble.
- Navigation systems for vehicles built for the
U.S.A. and Canada will not necessari ly work
in Europe, and may not work in other coun­
tries outside of North America.
Consumer Information 209
@ Note
Audi cannot be responsible for mechanical
damage that could result from inadequate
fuel, serv ice or parts availab ility.
Audi Service Repair
Manuals and Literature
Audi Offic ial Factory Service Manuals and Lit ­
erature are published as soon as possible after
model introduct ion. Service Manuals and liter­
at ure are available to order from the Audi
T echnical Literature Ordering Center at:
https: //www. audi.techliterature.com
Maintenance
' General
Your vehicle has been designed to help keep
maintenance requirements to a minimum.
However, a certain amount of regular mainte­
nance is still necessary to assure your vehicle's
safety, economy and reliability . For detailed
vehicle maintenance consult your Warranty& Maintenance booklet.
Under difficult operating conditions , for ex­
ample at extremely low outside temperatures,
in very dusty regions, etc., some service work
shou ld be pe rformed between the intervals
specified. This applies particularly to:
- oil changes, and
- cleaning or replacing the air fi lter.
@ For the sake of the environment
By regu larly maintaining your vehicle, you
help make sure that emission standards
are maintained, thus minimizing adverse
effects on the environment.
Important considerations for you and
your vehicle
T he increasing use of electron ics, soph isticat­
ed fuel injection and emission control sys­
tems, and the genera lly increasing technica l
complexity of today's automobiles, have ..,_
•
•

210 Consum er Inf orm ati on
steadi ly reduced the scope of maintenance
and repairs which can be carried out by vehicle
owners.
Als o, sa fe ty a nd en vir onm ent al con­
cerns p lace very strict limits on the nature of
repairs and adjustments to engine and trans­
miss ion parts which an owner can perform .
Maintenance, adjustments and repa irs usua lly
require special tools, testing devices and oth­
er equipment available to specially trained
workshop personnel in order to assure proper pe rformance, reliab ility and safety of the vehi­
cle and its many systems .
Improper maintenance, adjustments and re­ pa irs can impair the operation and reliab ility
of your vehicle and even void your vehicle war­
ranty. Therefore , proof of servic ing in accord­
ance w ith the ma intenance schedule may be a
condition for upholding a poss ible warranty
claim made within the warranty period.
Above all, operational safety can be adversely
affected, c reating unnecessary risks for you
and your passengers .
If in doubt about any se rv icing, have it done
by your author ized Audi dealer or any other
p roperly equipped and qualified workshop .
We strong ly urge you to give yo ur a utho rized
Aud i dealer the opportunity to perfo rm all
schedu led maintenance and necessary repairs.
Your dea ler has the facilities, original parts
and trained spec ialists to keep your vehicle
running properly .
Performing limit ed ma int enance your self
The following pages describe a limited num­
ber of proced ures which can be performed on
your ve hicle with ordinary too ls, shou ld the
need arise and trained personnel be unavaila­
ble. Before performing any of these proce­
dures, always thoroughly read all of the app li­
cable text and carefully follow the instruc ­
tions given . Always rigorously observe the
WARNINGS p rovided.
Before you ch eck a nything in th e eng ine
co mpartm ent , alwa ys re ad and h eed all
WA RNINGS
c::> .&. and c::> ..&. in Working in the
engine compartment on page 175.
A WARNING
- Serious personal injury may occur as a re­
sult of improperly performed mainte­
nance, adjustments or repa irs .
- Always be extremely careful when work­
ing on the vehicle . Always follow com­
monly accepted safety pract ices and gen­
eral common sense. Never r is k personal
injury.
- Do not attempt any of the maintenance ,
checks or repairs descr ibed on the fol­
lowing pages if you are not fu lly fam iliar
with these or other procedures with re ­
spect to the vehicle, or are uncertain how
to proceed .
- Do not do any work without the proper
too ls and equipment. Have the necessa ry
work done by your authorized A udi deal­
er or another proper ly equipped and
qualified workshop.
- Always remove the ignition key before
anyone gets under the veh icle.
- Always support your veh icle with safety
stands if it is necessary to work under­ neath the vehicle . The jack* is not ade­
quate for this purpose and cou ld collapse
causing ser ious personal inju ry.
- If you must work underneath the vehicle
with the wheels on the ground, a lways
make sure the vehicle is on level ground,
that the wheels a re a lways secure ly
b locked and that t he engine cannot be
started.
- Always make sure the transmission se­
lec to r l ever is in "N" (Neut ral) (R t ron ic)
or Neutral (manual transmission) and
the hand bra ke is f irmly app lied.
@ For the sake of the environment
- Changing the engine sett ings will ad­
verse ly affect emission leve ls. Th is is det­
r imental to the environment and increas­
es fuel consumpt ion .
- Always observe environmenta l regu la­
tions when disposing of old eng ine oil,
used brake flu id, dirty engine coo lant,
spent batte ries o r worn out tires.

-Undeployed airbag modules and preten ­
sioners might be classified as Perchlo­
rate Material -spec ia l hand ling may ap­
ply, see www.dtsc.ca.gov/hazardous­
waste/perch lorate. When the veh icle or
parts of the restraint system includ ing
airbag modules safety belts with p reten­
s ione rs are scrapped, all applicable laws
and regulations must be observed. Your
a utho rized Aud i dea le r i s f amiliar w ith
these req uirements and we recommend
that you have your dea le r perform this
service for you.
Additional accessories, modifications and
parts replacement
Additional accessories and parts
replacement
Always consult on authorized Audi dealer be­
fore purchasing accessories .
Your vehicle incorporates the latest safety de­
sign features ensuring a high standard of ac­
tive and passive safety .
This safety could be compromised by non -ap ­
proved changes to the veh icle. For this reason,
if parts have to be replaced, please observe
the following points when installing addition­
al accessories:
Approved Audi accessor ies and genuine Audi
parts are ava ilable from authorized Audi deal­
ers.
These dealers also have the necessary faci li­
ties, too ls and trained specialists to insta ll the
parts and accessor ies properly .
A WARNING
Using the wrong spare parts or using non­
approved accessories can cause damage to
the vehicle and se rious personal injury .
- Use only accessor ies expressly approved
by Audi and genuine Aud i spa re parts
Con sumer In formation 21 1
-These parts and accessories have been
specially designed to be used on yo ur ve­
hicle.
- Never install accessor ies such as tele­
phone crad les or beverage ho lders on air­
bag covers or within the airbag deploy­
men t zones . Do ing so wi ll increase the
ris k of injury if a irbags are triggered in an
accident!
- Before you check anything in the engine compa rtment, always read and heed a ll
WARNINGS
r:::;> poge 175.
(D Note
-If items other than genu ine Audi spare
parts, add-on equipment and accessory
items are used o r if repair wo rk is not
performed ac cord ing to specified met h­
ods, this ca n resu lt in severe damage to
yo ur vehicle's engine and bo dy (s uch as
co rrosion) and adve rsely affect yo ur vehi ­
cle 's warranty.
- The innovat ive a luminium concep t of
your Audi means that a ll servicing, re ­
pairs or other work on the vehicle body
must be carr ied out exclusive ly by an Au­
di workshop.
- If emergency repa irs must be performe d
elsewhere , have the veh icle examined by
an authorized Audi dealership as soon as
possible .
- The manufacturer cannot be held liable
for damage wh ich occurs due to failure
to comply with these stipu lations.
Technical Modifications
Our guidelines must be complied with when
technical modifications ore mode .
Always consult an author ized Audi dealer be·
fore start ing work on a ny modifications.
T his will help ensure t hat veh icle function,
performance and safety are not impaired
c> _&. .
Attempt ing to work on e lec tronic componen ts
and t he software used with them can ca use
Iii>
•
•