warning AUDI R8 SPYDER 2014 Owner's Guide

Wind deflector
The wind deflector reduces turbulence in the
passenger compartment and makes driving
more comfortable.
Fig. 33 Install ing the wind deflector
Fig. 34 Luggag .e compart ment: stor ing the wind de ·
flector
The wind deflector is located in the luggage
compartment . Insta lling it from the sid e of
the vehicle that is farthest from traffic is rec­
ommended for safety reasons . Fo llow the in·
stallat ion instructions provided in the storage
bag .
Installing /removing the wind deflector
.. To install the wind deflector, slide the re-
taining pin ® into the mount ®~
fig. 33 .
The wind deflector is secure when it clicks
into place and the red marks on both but­
tons are no longer visible .
.. To remove the wind deflector , press both
bu ttons © and pull the deflector upward.
Storing the wind deflector
.. Slide the wind deflector into the storage bag
with the retaining pins facing dow nward .
.. Hang the storage bag o n the retainers @) in
the luggage compartment ~
fig. 34.
Convertible top 39
A WARNING
-Do not use the wind deflector to secure
cargo or other objects . Th is could result
in injury.
- Be careful of traffic when installing the
wind deflector.
(D Note
To prevent damage to the vehicle paint, do not lean on the vehicle when installing the
wind deflector . Objects such as belt buck­
les could scratch the surface of the paint .
(D Tips
-Keeping both side windows raised pro­
vides the best wind protection.
- To prevent mildew, do not store the wind
deflector when it is damp.
Rear window
Fig. 35 Rear window in win d deflecto r position
Fig. 36 Section of the center console: convertible top
swi tc h
The rear window can be extended s light ly
when the convertible top is open to reduce air
movement inside the vehicle and increase
comfort . This is called the w ind deflector posi -
t ion
~ fig. 35 . ..,.

40 Convertible top
The rear window can be extended comp lete ly
for cleaning. This is ca lled the cleaning posi­
tion.
E xtendin g the rear w indow into th e w ind
d efl ector po sit io n
.. Pull and hold the rear window switch
¢ fig. 36 .
.. Re lease the switch once the rea r window has
reached the wind deflector position.
E xte nding th e rear window into th e
cle aning po sition
.. Pull and hold the rear window switch
¢ fig . 36.
.. Release the switch once the rear window has
reached the wind deflector position .
.. Pull and hold the rear w indow switch again .
.. Pull and hold the convertible top switch
within one second
¢ page 37, fig . 32.
Re tra cting the re ar w indow
.. Press and hold the rear window sw itch until
the window has been retracted .
Retra cting the re a r wi ndow using the one­
t ouch function
.. Press the rear window switch briefly . There
is no need to hold the switch .
The rear window can only be operated when
t he igni tion is switched on.
The rear window can also be extended or re­
tracted when the convertib le top is closed.
A WARNING
- Do not use the rear window to secure car­
go or other objects. This could result in
mJury .
- Always pay attention and be careful
when extending or retracting the rear
window . It could cause injury by pinch­
ing .
(D Tips
-Keeping all of the w indows raised pro­
v ides the best wind protection . - The vehicle must be stationary to bring
the rear window into the cleaning posi­
tion . The rear window will retract once
you begin dr iv ing .
Convertible top
emergency operation
General information
The convertible top can be closed by hand if
there is a malfunction .
First check if overload protection is active
¢ page 38. If this is the case, the convertible
top wi ll operate again afte r a short de lay. Oth­
erwise the fo llowing steps must be completed
before closing the convertib le top:
.. Activate the pa rking brake .
.. Open the side w indows, if necessary.
.. Remove the key from the ignition.
E mergency loc king is not intended for long­
term use or long d rives . The convertible top
will not be completely waterproof after using
the emergency locking procedure because the
seals wi ll not be seated correctly. Only close
the convertible top manually in an emergency .
Please see an authorized Audi R8 dealer to
have the cause of the malfunction corrected .
A WARNING
-The ignition must be sw itched off d uring
the entire closing p rocedu re.
- When pos itioning the convertible top,
avoid contact with the supports or other
movi ng parts. Otherwise you could p inch
your hands.
- Never drive when the convert ible top is
not locked correctly . The wind from d riv­
ing could cause the convertible top to
open . This can resu lt in injuries and dam­
age to the vehicle.
(D Tips
Have a second person assist when clos ing
the convert ible top. Opening the storage
bay lid and positioning the convertible top
i s easier when a second person is assisting.

Step 1: Retract the rear window
Fig. 37 Upper storage compartment: removing the
cover
Fig. 38 Upper storage compartment: using the Allen
wrenc h as a crank to lower the rear window
~ 0 N ... a,
,__ ,-. M C)
"' ... a,
The rear window must be retracted in order to
close the convertible top. If the rear window
switch is not functioning ¢
page 39, the rear
window can be cranked .
.. Open the upper storage compartment be­
tween the seat backrests ¢
page 61 .
.. Remove the cover using the screwdriver
from the vehicle tool kit¢
fig. 37 .
.. Press the Allen wrench from the veh icle tool
k it firmly into the opening until it cl icks into
place¢
fig. 38.
.. Turn the bolt clockw ise until the rear win­
dow is lowered.
Step 2: Release the pressure in the
hydraulic system
The pressure in the hydraulic system must be
released before the convertible top can be
closed.
.. Switch the ignition
off.
.. Pull or press the convertible top switch
¢page 37, fig. 32 for approximately 10 sec­
onds.
Convertible top 41
A WARNING
If convertible top operat ion fa ils when
opening or closing the top, do not hold or
touch the supports or other moving parts
when releasing the pressure. The converti­ ble top will sink down and could pinch your
hands.
Step 3: Open the convertible top storage
bay lid
Fig. 39 Engine compartment: install ing the emergency
operation bolts
Fig. 40 Raising t he storage bay lid and pulling it back
The engine compartment lid must be released
using the emergency procedure in order to re­
lease the storage bay lid
¢page 172 .
Releasing the convertible top storage bay
lid
.. Turn the emergency operation bolts on the
left and right sides of the engine compart­
ment¢
fig. 39 clockwise using the open end
wrench from the vehicle too l kit until the
bolts are installed completely . The converti­
ble top storage bay lid will raise approxi­
mately 0.4 in (1 cm) from the vehicle when
the bolts are insta lled comp letely.
.. Close the engine compartment lid
¢page 174.

42 Convertible top
Opening the conv ertible top stor age bay
lid
• From the r ear of the vehicle, r each into the
center ventilation slot in the sto rage bay lid
wi th both hands and raise the lid approxi­
mately 12 in (30 cm).
• Hold the storage bay lid in this posit ion and
pull it toward you until it stops ¢
fig. 40.
A WARNING
When working in the engine compart­
ment:
- T urn the engine off.
- Act ivate the park ing brake.
-
- In vehicles with a manua l transm iss ion,
move the sh ifter lever into idle . In
vehicles with the R tronic transmission,
move the se lector lever into the N pos i­
t ion.
- Remove the ignit ion key .
- Let the engine cool down .
- Keep children away from the engine com-
partment.
(D Note
To prevent damage to the vehicle, only
open the convertible top storage bay lid
when the engine compartment lid is
closed.
Step 4: Remove the covers
Fi g. 41 Conv ertib le top : cov ers ma rk e d
Fig. 42 Co nver tible top storage bay lid: r em ov ing t he
c o ver
T he following steps mus t be performed on
both sides of the vehicle .
• Remove the bo lt in the cover on the bo ttom
side of the sto rage bay lid using the open
e nd w rench from the vehicle too l kit
(D
¢ fig . 42.
• Move the cover up and down carefully until
it can be pulled downwa rd from the teeth
@ .
Step 5: Lift the convertible top out
Fig. 4 3 Conve rtib le to p sto rage bay: liftin g th e c onve r­
tible top o ut
Fig . 44 Wind shi eld fr ame: p res sing the c onvert ible top
fo rwa rd
• Ho ld the conve rtib le top at the@ point (ar ­
row)
r:!;> fig. 43 and raise it carefu lly ¢ A . .,..

.. Pull the convertible top all the way out in
the direction indicated @. Position the fins
upward at the same t ime.
.. Press the convertib le top as far forward to­
ward the windshield frame as possible
Q fig. 44 .
Have a second person assist when positioning
the convertible top. That person should stand
on the opposite side of the vehicle and per­
form the same steps.
_& WARNING
-When positioning the convertible top,
avo id contact with the supports or othe r
moving pa rts. O the rw ise you cou ld pinch
yo ur hands.
- Whe n pressing the convert ible top down
onto the windsh iel d frame, make s ure
that you do not pinch yoursel f or anyone
else .
Step 6: Secure the convertible top
-
Fig . 4 5 Co nvertible top sto rage bay: installi ng the driv­
er
F ig . 4 6 Securing th e convert ib le top
The convertible top must be under tension to
secure it to the windshie ld frame. The wheel
wrench, dr iver and bolts from the vehicle tool
kit a re required for this.
Con vert ible top 4 3
Have a second person assist with th is step .
That person should stand on the opposite side
of the vehicle and perform the same steps .
.. Posit ion the dr iver @ on the bo lt @ in the
front sect ion of the convert ible top storage
bay and rotate clockwise to insta ll in the
threads ~
fig. 45.
.. Posit ion the wheel wrench © with the long
end on the driver @.
.,. Press the convertible top as far forward as
possible toward the windshie ld frame @
w ith one hand~
fig. 46. At the same t ime,
pull the fins upward @for support with the
other hand.
.. Now, grasp the fins with the hand that you
used to move the convertib le top forward
and hold the fins in this position . Wit h the
other hand, turn the wheel wrench upward
until it stops @.
(D Tips
-When pressing the convertible top for­
ward, make sure the locking pins are
seated in the latch o n the windshield
frame and not on the frame itself.
- When press ing the convert ible top for­
ward, make sure the locking pins are
seated exactly i n the latch on t he wind­
shield frame and not on the frame itself.
T his is t he on ly way that the convertib le
t op can be latched cor rect ly .

44 Convertible top
Step 7: Lock the convertible top
Fig . 47 Inner s ide of the convertible top : remov ing the
cap
F ig. 48 In ner s ide of the co nvertible top: pos it ion ing
the Allen wrench
... Remove the cap in the center of the conver­
tible top using the screwdriver from the ve­
hicle tool kit
c::> fig. 47. The emergency lock­
ing mechanism is located behind it.
... Insert the Allen wrench
(D and turn the bolt
to the left @until it is tight and the conver­
t ible top is locked securely
c::> fig. 48.
.,. Remove the Allen wrench from the open ing
and cover the open ing with the cap .
... Remove the wheel wrench from the conver­
t ib le top storage bay .
... Close the convertib le top storage bay lid .
A WARNING
Make s ure the convert ible top is locked
correctly. Otherwise the wind from driving
could cause the convertible top to open.
This can result in inju ries and damage to
th e vehicle.
-
Step 8 : Secure the fins on the body
F ig . 4 9 Co nve rtib le top : press ing t he f ins downward
F ig . SO Inte rior: tightening the bo lt
The following steps must be performed on
both sides of the veh icle .
... Press the fin downward firmly
c::> fig . 49 .
.,. Ho ld the fin in th is position and tighten the
bolt above the seat belt -arrow-us ing the
Allen wrench from the vehicle tool k it at the
same time
c::> fig. 50.
A second person should assist when securing
the fins to the body. Tightening the bolts is much easier if a second person presses the
fins down .
A WARNING
-
Make sure the fins lie on the body. Other -
wise the convert ible top will not lock se­
cure ly and it could open while driv ing. This
ca n resul t in in ju ries and d amage to the
vehicle.
-

shown as active in the driver information
system.
The
coming home function illuminates the
area around the vehicle when the ignition is
switched off and the driver 's door is opened.
The length of time the lights rema in on can be
set in the menu display
(Lights> Exterior
lights> coming home) .
The leaving home function illuminates the
area around the vehicle when unlock ing it.
A WARNING
- Never use daytime running lights to see
where you are going. They are not bright enough and will not let you see far
enough ahead for safety, especially at
dusk or when it is dark . Be aware of
changes in outside light conditions when
you are driving and respond by switching
on your low beams.
- Automatic head- and taillight control is
only intended to assist the driver. This
feature does not relieve the driver of his
responsibility to check the headlights
and to turn them on manually according
to the current light and visibility condi­
tions. For example, fog and rain cannot
be detected by the light sensors. Conse­
quently, always switch the headlights on
under these weather conditions and
when driving in the dark.
- Crashes can happen when you cannot see
the road ahead and when you cannot be
seen by other motorists .
-Always turn on the headlights so that you can see ahead and so that others can see your car from the back.
- Please observe legal regulations when
using the light ing systems descr ibed .
@ Tips
-Always observe the specific local regula­
tions for your area when to use your
lights .
- Turn on low beams as evening ap­
proaches or in conditions of poor visibili­
ty. Clear vision 4
7
- Do not attach stickers to the windshield
in front of the sensors as this can disable
the automatic head- and taillight control
and the automatic glare-dimming of the
rearview mirror(s)*.
- If you remove the ignition from the igni­
tion lock while the headlights are still
on, a buzzer will sound as long as the
driver's door is open to remind you to
turn off the lights .
- In the AUTO mode, the low beams are
turned off when the ignition is turned
off. The remaining lights are turned off
when the key is taken out of the ignition .
- In cool or damp weather conditions the
headlights may fog over temporarily on
the inside.
- The critical factor is the temperature
difference between the interior and the
exterior of the headlight Lens.
- With the main beams switched on, the
light-emitting area will be free of con­
densation after a short time, however
the edges of the glass may still be fog ­
ged .
- This physical phenomenon has no ef­
fect on the life of your vehicle's light­
ing system .
Turn signals and high beam lever
The lever on the left side of the steering col­
umn is used to operate the turn signals and the high beam as well as the headlight flash­
er.
t
'
Fig. 53 Turn signal and high b eam lever
The turn signal and high beam lever has the
following functions: ..,.

48 Clear vis ion
Turn sign als¢ Q (D@
.,. Push the lever up as far as it can go to turn
on the r ight turn signal or down to turn on
the left turn signal
c;, fig. 53 .
.,. Move the lever briefly until you meet resist­
ance and release it to flash three times .
.,. Move the lever (up or down) until you meet
resistance and ho ld it there to determine
the flash ing t ime for the turn signals.
High beam [D @
.,. Push the lever forward to switch on the high
beam.
.,. Pull the lever back towards you to swi tch off
the high beam .
Headl ight fla she r [D ©
.,. Pull the lever toward the steering wheel to
use the headlight f lasher.
Notes on these features
- T he turn signals only work with the igni tion
switched on . The ind icator lights
II or 1M in
the instrument cluster
i::> page 11 also b link .
- After you have turned a corner, the tur n sig -
nal switches off a utomat ica lly.
- T he
high beam works only when the head­
li gh ts are on. The indicator light
II in the
instrument cluste r illuminates when the
high beams are on.
- T he
headlight flasher works on ly as long as
yo u hold the lever -even if there are no
li ghts turned on . The indicator light
II in
the instrument cl uster i llum inates when you
use the headl ight f lasher.
A WARNING
Do not use the hig h beam or headlight
flashe r if you know that these could blind
oncoming traffic.
Emergency flasher
SPORT •
Fig. 5 4 Center co nsole : em erge ncy flashe r sw itc h
.,. Press the switc h lil i::> fig. 54 to switch the
emergency flasher on or off .
When the emergency flasher is on, all four
turn s ignals b link at the same time. The turn
s ignal indicator lights
II IB in the instrument
cluster, as well as the light i n the emergency
flasher sw itch
&,. blink likew ise . The eme rgen­
cy flashe rs also work when the ign ition is
tu rned off.
The emergency flasher will automatically switch on if you are in an accide nt whe re the
airbag has deployed.
@ Tips
You should sw itch on t he emergency flash­
er when :
- you are the last veh icle standing in a traf­
fic jam so that any other vehicles coming
can see you, o r w hen
- your vehicle has broken down or you a re
in an eme rgency s ituation, o r when
- your vehicle is be ing towed by a tow
truck or if you are towing another veh icle
beh ind you .

50 Clear vis ion
- Canada mode ls: instrument panel illumi ­
nation will stay bright regard less of the
i ntensity of amb ient light. Always be
aware of changes in outside light condi­
tions whi le you are driv ing. Respond in
time to fading daylight by turning the light sw itch to position @,0 (or "AUTO " if
you r ca r is equ ipped with this feature) to
tu rn on your headl igh ts.
Luggage compartment light
The ligh t is loc ated on t he righ t side of the
l uggage compartmen t.
These lights come on automat ica lly when the
front lid is ope ned . T he lights tu rn off au to­
mat ica lly if the lid is left open for more t hen
10 minutes .
Vision
Adjusting the exterior mirrors
Fig. 57 Forwa rd se cti on of drive r' s armr est: pow er mir ­
r o r co ntrols
Turn the knob to the desired position :
Q/P - In this position, you can adjust the
driver's and fron t passenger's exter ior mirrors
by turn ing t he knob in the des ired direction .
outs ide temperature.
8 - The exterior mirrors fold in *
You are well-advised to fold the ex te rior m ir­
rors in when mane uvering in tight spaces or
when leaving the car parked close to other
vehi cles .
A WARNING
--Curved (i.e . convex) m irror surfaces in-
crease your field of view. Remember that
veh icles or other objects will appea r
sma ller and farther away than when seen
i n a flat mirror.
If you use th is m irror to
estimate dis tances of followi ng ve hicl es
when changing lanes, yo u co uld estimate
i n correct ly and cause an accident .
(D Note
-If the m irror housing is moved uninten­
ti onally (for examp le , while p arking your
vehicle), then yo u m ust first fold t he mir­
ror electrically. Do not readjust the mir ­
ror housing manually . You cou ld damage
the motor which controls the mirror .
- If you wash the vehicle in an automatic
car wash, you must fo ld the exter ior mir­
rors in to reduce the risk of damage to
the mirro rs . Never fold powe r folding ex­
terior mirrors* by hand . Only fold them
in and o ut using the power controls .
@ Tips
If there should be a malf u nction in t he
electr ica l system, you can st ill adjust the
ex ter io r mirrors by pressing the edge of
the m irror.
Dimming the mirrors
Fig . 58 Auto matic dimmin g rearv iew m irro r*
Manu al anti-glare adju stment
.,. Move the small lever ( located on the bottom
edge of the mirror) to the rear .
Ill>

Automatically dimming mirr ors*
• To d im the rearv iew mirror and both exterior
mirrors, press the @ button. The diode @
turns on. The rearview and exterior mirrors dim automat ically when light shines on
them, for example from headlights on ave­ hicle to the rear.
A WARNING
E lectrolyte flu id can leak from automatic
dimming m irrors if the glass is broken.
Electrolyte flu id can irritate skin, eyes and
respiratory system.
- Repeated or prolonged exposure to elec­
tro lyte can cause irritation to the respira­
tory system, espec ially among people
with asthma or other respiratory condi­
tions . Get fresh air immediately by leav­
ing the vehicle or, if that is not possible,
open windows and doors a ll the way.
- If electrolyte gets into the eyes, flush
them thoro ughly with large amounts of
clean water for at least 15 m inutes;
medica l attention is recommended.
- If electrolyte contacts sk in, flush affect­
ed area with clean water for at least 15
minutes and then wash affected area
with soap and water; medical attention is recommended . Thoroughly wash af­
fected clothing and shoes before reuse .
- If swallowed and person is conscious, rinse mouth w ith water for at least 15
minutes . Do not induce vom iting un less
instructed to do so by medical professio­
nal. Get medical attention immediately.
(D Note
Liquid elect rolyte leaking from broken mir­
ror glass will damage any p lastic surfaces
it comes i n contact w ith. Clean up spilled
elec trolyte immediately with clean water
and a sponge.
(D Tips
- Switch ing off the dimming func tion of
the i nside rear view m irror also deact i-
Clear vi sion 51
vates the automatic dimming function of
the exterior mirrors .
- T he automatic dimming mirrors do not
dim when the interior lighting is turned
on or the reverse gear is selected .
- Automatic d imm ing fo r the mirror on ly
operates properly if the light striking the
inside mirror is not hindered in any way.
, Sun visors
,.--~ --~-- -------.
Fig . 59 S un vi so r
The vanity mirrors in the sun visors are equip­
ped with covers .
Wiper and washer
system
Windshield wiper
The windshield wiper lever controls both the
windshield wipers and the washer system.
Fig . 60 W iper le ver: win ds hiel d wiper le ver positio ns
The windshield wiper lever I:!) fig. 60 has th e
fo llowing positions:
Int ermittent wiping ~1 (acti vating r ain
s e n sor )*
• Move the lever up to position (!).