oil AUDI RS5 CABRIOLET 2015 Owner's Manual

"' N
a: LL co
rl I.O
"' rl
"' rl
Checking and fillin g 197
Engine compartment
Engine compartment
These are the most important items that you can check.
Fig. 174 Typical layout for containers and engine oil filler cap
(D Coolant expansion tank (- L) . . . 202
@ Jump start point(+) under a cov-
er .. .. ... ....... ........ ..
207, 256
@ Engine o il filler cap ( @ Jump start point(-) with hex
head screw ............ .... .
207, 256
© Brake flu id reservoi r((())) . . . . . 204
® W indshie ld/headlight* washer
container
(0) . . . . . . . . . . . . . . 208
A WARNING
Before yo u check anything in the engine
compartment, always read and heed all
WARNINGS
q .& in Working in the engine
compartment on page 195.
-
Engine oil
Engine oil specifications
The engine oil used must conform to exact
specifications .
The service interval disp lay in the instrument
cluster of your vehicle will inform y ou when it
is time for an oil change. We recommend that
you have your oil changed by an authorized
Audi Se rv ice Advisor .
If you have to top off the o il between o il
changes, use the Audi o il quality standard
specified in the tab le.
Audi oil quality standard
Gasoline
VW 502 00 or
eng ine vw 504 00 ...

198 Checking and filling
Using the proper engine oil is important for
the functionality and service life of the en­
gine. Your engine was factory-filled with a
high-quality oil which can usually be used
throughout the entire year.
0 Note
Your Limited New Vehicle Warranty does
not cover damage or malfunctions due to
failure to follow recommended mainte­
nance and use requirements as set forth in
the Audi Owner's Manual and Warranty
&
Maintenance booklet.
- Use only a high quality engine oil that ex­
pressly complies with the Audi oil quality
standard specified for your vehicle's en­
gine . Using any other oil can cause seri­
ous engine damage.
- Do not mix any lubricants or other addi­
tives into the engine oil. Doing so can
cause engine damage.
If you need to add oil and there is none
available that meets the Audi oil quality
standard your engine requires, you may
add a total of no more than 0.5 quart/liter
of a high-quality "synthetic"oil that meets
the following specifications.
- Vehicles with gasoline engine: ACEA A3
or API SM with a viscosity grade of
SAE 0W-30, SAE SW-30 or SAE SW-40.
- For more information about engine oil
that has been approved for your vehicle, please contact either your authorized
Audi dealer or Audi Customer Relations
at 1 (800) 822-2834 or visit our web site
at www.audiusa .com or
www .audicanada .ca .
Engine oil consumption
The engine in your vehicle depends on an ade ­
quate amount of oil to lubricate and cool all
of its moving parts.
In order to provide effective lubrication and
cooling of internal engine components, all in­
ternal combustion engines consume a certain amount of oil. Oil consumption varies from
engine to engine and may change significantly
over the life of the engine. Typically, engines
with a specified break-in period (see
¢ page 179) consume more oil during the
break -in period than they consume after oil
consumption has stabilized.
Under normal conditions, the rate of oil con­
sumption depends on the quality and viscosity
of the oil, the RPM (revolutions per minute) at
which the engine is operated, the ambient
temperature and road conditions . Further fac­
tors are the amount of oil dilution from water
condensation or fuel residue and the oxida­
tion level of the oil. As any engine is subject to
wear as mileage builds up, the oil consump­
tion may increase over time until replacement of worn components may become necessary.
With all these variables coming into play, no
standard rate of oil consumption can be es­
tablished or specified. There is no alternative
to regular and frequent checking of the oil lev­ el, see
Note.
If
the yellow engine oil level warning symbol
El in the instrument cluster lights up, you
should check the oil level as soon as possible
¢ page 199. Top off the oil at your earliest
convenience
¢ page 199.
A WARNING
--
Before you check anything in the engine
compartment, always read and heed all
WARNINGS¢
& in Working in the engine
compartment on page 195.
{(D Note
Driving with an insufficient oil level is like­
ly to cause severe damage to the engine .
(D Tips
- The oil pressure warning display. is
not an indicator of the oil level. Do not
rely on it. Instead, check the oil level in
your engine at regular intervals, pref­ erably each time you refuel, and always
before going on a long trip. .,.

"' N
a: LL co
rl I.O
"' rl
"' rl
-If you have the impression your engine
consumes excessive amounts of oi l, we
recommend that you consult an author­
ized Audi dealer to have the cause of
your concern properly diagnosed. Keep in mind that the accurate measurement of
oil consumption requires great care and may take some time. An authorized Audi
dealer has ins tructions about how to
measure oil consumpt ion accura tely.
Checking the engine oil level
F ig. 175 MMI Display: Oil leve l indicator
Read oil le vel
"' Park your vehicle so that it is horizonta lly
level.
"' Shut the engine off when it is at operating
temperature.
"' Switch only the ignition back on .
"' Wa it approx. two minutes.
"' Se lect: Funct ion button
I _C_A_R_I > Oil l e v e l. Or
"' Se lect: Funct ion button
I CARI > Car sy s-
tem s* control button > Servicing & check s >
Oil level.
"' Read the oil leve l in the MMI* Display
r:::> fig. 175. Add engine oi l if the bar of the
o il level indicator is near "min"
r:::> page 199
Depending on the way the vehicle is driven
and the operating conditions, oil consumption
can be up to 1 quart per 600 mi les (0.8 liter
per 1,000 km). Consumption may be higher
within the first 3,000 miles (5,000 km) .
(D Tips
The oil level indicator in the MMI* Disp lay
is only an information display . If the oil
level is too low, a min imum oil warning ap-
Checkin g and fillin g 199
pears in the instrument cl uster . Add oil
Q page 199. If the hood has been opened,
the current oil leve l is shown in the instr u­
ment cluster the next time the ignition is
switc hed on.
F ig . 17 6 En gin e compart ment: Cover on the oil filler
n eck
"' Before you check anything in the engine
compa rtment,
alwa ys read and h eed all
WARNINGS r::> .&. in Working in the engine
compartment on page 195.
"' Shu t the eng ine off.
"' Unscrew the cap
't::::r. to the engine oil filling
hole
¢ fig. 176, ¢page 197, fig. 174.
"'Carefully top off with 0 .5 quarts (0 .5 liters)
of the appropr iate oil
¢page 197.
"'Check the oil level again after two minutes
r:::> page 199, Checking the engine oil level.
"'Top off the o il aga in, if necessary .
"' Screw the cap back on the fi lling hole .
.&_ WARNING
-W hile topping off, the o il m ust n ot come
in contact with hot e ngine parts -fir e
hazard !
- Th e oi l filler cap mus t be p roperly se­
cured to prevent oil from being sp rayed
on the hot engine and exhaus t system
when the engine is runn ing -fire haza rd!
- If you r skin has come in contact wi th the
e ngine o il, you must subse quently
cleanse it thorough ly.
(D Note
- Check the oil leve l using the r adio or
M MI*. I f the message
Plea se reduce oil

200 Check ing and filling
le vel appears, contact your authorized
Audi dealer or qualified workshop to have excess oil extracted if necessary.
- Aud i d oes not recomme nd th e use of o il
add it iv es. T he y ma y dam ag e the e ngine
and ad ve rsel y a ffect you r New Vehicle
Wa rrant y.
@ For the sake of the environment
- Under no circumstances can the oil come
in contact with the sewage network or
the soil.
- Observe and follow lega l regu lations
when disposing of empty oil containers.
Changing the engine oil
We recommend that hove your oil changed by
on authori zed Audi dealer or a qualified serv­
ice station.
Before you check anything in the engine com­
partment,
a lways r ea d and h eed all W ARN ·
ING S
q & in Working in the engine comport­
ment on page 195.
The engine oil must be changed according to
the intervals specified in your Warranty
&
Maintenance book let. This is very important
because the lubricating properties of oil di­
minish gradually dur ing normal veh icle use .
Under some circumstances the engine oi l
should be changed more frequently . Change
oil more often if you drive mostly short dis­
tances, operate the vehicle in dusty areas or
under predominantly stop-and-go traffic con·
d itions, or have your veh icle where tempera·
tures remain below freez ing fo r extended pe­
riods.
Detergent addit ives in the o il w ill make fresh
oil look dark after the eng ine has been run­
n ing for a short time. This is no rma l and is not
a reason to change the oil more often than recommended.
Because of the prob lem of proper disposal ,
a long w ith the special tools and necessary ex­
pertise required, we strong ly recommend that you have your oil changed by an authorized
A
udi de ale r or a qualified service station.
If yo u choo se t o c hange y our oi l yourse lf ,
please note the follow ing important informa ­
t ion:
_& WARNING
To reduce the risk of personal injury if you
must change the eng ine oil in your vehicle
yourself:
- Wear eye protection .
- To reduce the risk of burns from hot en -
gine oi l, let the engine cool down to the
touch .
- When removing the o il dra in p lug with
your fingers, stay as far away as possible.
Always keep your forearm parallel to the ground to help prevent hot oil from run· n ing down your arm.
- Dra in the oil into a container designed
for this purpose, one large enough to hold at least the tota l amount of oil in
your engine .
- Engine oil is poisonous. Keep it we ll out
of the reach of children.
- Continuous contact with used eng ine o il
is harmful to your sk in . Always protect
your skin by washing oil off thoroughly
wit h soap and water.
(D Note
Never mix oil additives with your engine
oil. These additives can damage your en­
g ine and adversely affect your Aud i Limit­
ed New Veh icle Warranty.
@ For the sake of the environment
- Before changing your oil, first make sure
you know where you can properly dispose of the used oil.
- Always dispose of used eng ine oil proper­
ly. Do not dump it on garden soil, wood­
ed areas, into open streams or down
sewage drains.
- Recycle used engine oil by taking it to a
used engine oil collect ion faci lity in you r
area, or contact a service station.

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Engine cooling system
Coolant
The engine coolant performs two functions: it
keeps the engine from overheating and it pro ­
tects the engine from freezing in the winter .
The cooling system is sealed and generally re­
quires little attention.
T he cooling system has been filled at the fac­
tory with a permanent coolant which does not need to be changed. The coolan t consists of a
mixture of specially conditioned water and the
manufacturer 's glycol-based coolant addi-
tive G13 antifreeze with ant icorros ion addi­
tives (50% for USA models ; 60% for Ca nadian
models) . Th is mixture both assures the neces­
sary frost protection and protects metal com­
ponents in the engine's coo ling system from
corrosion and scaling. It a lso raises the boil­
ing point of the coo lant.
D o not reduce the concentration o f the coo l­
ant in the summer by adding plain water .
The
proportion of coolant additive mu st be at
least 50 % but not more than 60 %
to main­
tain antifree ze protection and cooling efficien­
cy. If the coolant frost protect ion is too low,
the coolant could freeze and damage the veh i­
cle heating and eng ine cooling system .
For year-round driving, antifree ze is added at
the factory for temperatures down to:
- -31° F(-35°C)USA
- - 4 0 ° F ( -40 °C) Canada.
I f you must add coo lant, use a m ixture of wa­
ter and coolant addit ive. Mixing the coolant
addi tive wi th disti lled wate r is recommended.
A WARNING
Be fore yo u check any thing in the engine
compartment, always read and heed all
WARNI NGS
~ .&. in Working in the engine
compartment on page 195.
(D Note
- Befo re win ter sets in, have the coolan t
checked to see if t he coolant ad dit ive in
-
Checkin g and fillin g 201
your vehicle is sufficient to meet the cli ­
mate conditions . This is especia lly impor ­
tant if you live in a region where the win ­
ter is extreme ly co ld. If necessary, in­
c rease the p ropo rtion of coo lant add itive
to 60% .
- When adding coolant additive to your
cooling system, remember:
- We re commend using on ly coola nt ad­
d itive G 12++ or G 13 for your veh icle .
T his coolan t ad di tive is availab le a t au­
thor ized Audi dealers. Other types of
antifreeze can significantly reduce cor ­
rosion protection. The resulting corro­
sion can cause a loss of coolant and se­
rious engine damage .
- Do not add any type of rad iator leak seal­
ant to your vehicle's engi ne coolant .
Add ing radiator repa ir flu id may adverse ­
ly affect the f unction and performance of
your cooling system and cou ld resu lt in
damage not covered by you r New Ve hicle
Li mited War ran ty.
•
•

202 Checking and filling
Checking the engine coolant level and
adding coolant
Be very careful when adding engine coolant.
Fi g. 1 77 En g in e c ompart men t: C over on the coola nt
ex pan sion ta nk
Fig. 178 Engine co mpar tment : ma rkin gs in th e coolant
ex pan sio n ta nk
Before you che ck anything in the engi ne com­
partment,
a lwa ys r ead and heed all WARN­
INGS c> A in Working in the engine compart ­
ment on page
195.
The "M IN " und "MAX " mark ings a re found o n
the bi -level disc in the in terior of the coolant
expansion tank
¢ fig . 178.
.,. Pa rk you r vehi cle on a level sur face .
.,. Turn off t he igni tion.
.,. Let the engine coo l down .
.,. Place a thick rag over the coolant expansion
tank and
c a refully turn the cap cou nte r­
clockwise
c> _&. .
.,. Read the eng ine coolant level inside the
coolant expans io n tank
c> fig . 177,
c>page 197 , fig. 174 . With a cold engine,
the coolant level sho uld be betwe en the
" M IN " and "MAX " ma rkings <=>
fig. 178
-arrows- . W he n t he eng ine is wa rm, the lev­
el may be slightly
above the "MAX" marking . .,.
Add coo lant mixed in the correct rat io, if
necessary
c> page 201 . Coolant may be a
maxim um of 1 mm above the MAX marking .
.,. Twist the cap on again
tightly.
The location of the coo lant expansion tan k
can be seen i n the engine compartment illus ­
tration
c> page 197.
T o obtain an acc urate reading, the engine
must be sw itched off.
T he ex pan sion ta nk in your vehicle is eq uipped
with an ele ctric coo lant level senso r.
When the coolant level is too low , the wa rn ing
li ght in the Au to-Check System <=>
page 17 will
blink u nti l yo u ad d coolant and the level has
been restored to normal. Eve n t hough t here i s
an e lectri c coo lant level senso r, we still rec ­
ommend you check the coola nt level from
time to t ime.
Coolant loss
Coolant loss may indica te a leak in the cooling
system. In t he event o f coolant loss, the coo l­
i ng system shou ld be inspected immediately
by your a uthorized Audi dea ler . It is not
eno ugh mere ly to add coolant.
In a
sealed sys tem, losses can occur on ly i f
the boili ng point o f the coo lant is exceeded as
a res ult of overheating.
Adding coolant
Rep la cement engine coo la nt must conform to
exact spe cificat ions
c> page 201, Cool ant .
We recommend using only coolant add it ive
Gl 2++ , Gl3 or in an emergency G 12 +. Do not
use a diffe rent add itive. In an emerge ncy use
plain w ater until yo u can get the correc t addi­
tive a nd can res tore the cor rect ra tio. T hi s
sho uld be done as soon as possib le .
If you have lost a considerab le amou nt of
c oolant , the n you shoul d a dd cold an tifreeze
and co ld wate r on ly w hen the e ng ine is cold.
Always use
n ew engine coo lant w hen refilling .
Do not f ill coo la nt
above the "MA X" mark. Ex-
cess coolant will be forced o ut through the .,,_

204 Checking and filling
Brake fluid
Checking brake fluid level
The brake fluid level can be checked with a
quick glance .
N N ~ N
" (X) (0
Fig. 179 Engine compartme nt: Cover on the brake flu ·
id reservo ir
Before you check anything in the engine com­
partment,
a lwa ys re ad and heed all WARN·
ING S ¢.&._ in Working in the engine compart­
ment on page 195 .
.. Read the brake fluid level from the brake
fluid reservoir
¢ fig . 179 , ¢page 197,
fig . 174.
The brake fluid level must be be ­
tween the "MIN" and
"MAX" markings.
The brake fluid reservoir is located at the rear
partition of the engine compartment on the
left side
¢ page 197.
The fluid level may drop slightly after some
time due to the automatic adjustment of the
brake pads. This is not cause for alarm.
If the brake fluid level falls
considerably be­
low the "MIN" mark, the brake warning/indi­
cator light (U.S. models:
11111 , Canadian
models :. ) will come on
¢page 15. Do not
continue to operate the vehicle. The complete brake system should be thoroughly checked
by an authorized Audi dealer or qualified
workshop and the cause corrected .
If the
brake fluid level is too low, the brake warn ing/
indicator light w ill illuminate. Contact an au­
thorized Audi dealer
immedi atel y.
@ Tips
The brake fluid reservoir is located under­
neath the cover.
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician .
Brake fluid absorbs moisture from the air. If
the water content in the brake fluid is too
high, corrosion in the brake system may result
after a period of time . The boiling point of the
brake flu id will also decrease conside rably and
decrease braking pe rformance.
Therefore, the brake fluid must be changed
every two year s. Always use new brake flu id
which conforms to Federal Motor Veh icle
Standard "F MVSS 116 DOT 4".
The brake fluid reservoir can be diff icult to
reach, therefore, we recommend that you
have the brake fluid changed by your author­
ized
Audi d ealer . Your dealer has the correct
tools, the right brake fl uid and the know -how
to do this for you .
A WARNING
- Brake fluid is poisonous . It must be stor­
ed only in the closed original container
out of the reach of children!
- Brake failure can resu lt from o ld or inap­
propriate brake flu id. Observe these pre­
cautions:
- Use only brake f luid that meets SA E
specifica tion
J 1 7 03 and conforms to
Federa l Moto r Ve hicle Standard 1 16.
Always check with yo ur authorized Aud i
dealer to make sure yo u are using the
correct brake fluid. The correct type of brake f lu id is also indicated on the
brake fluid reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
l ong. This can seriously affect the effi­
c iency of the brakes as well as your
safety. This cou ld resu lt in an accident.
(D Note
Brake fluid will damage the paint of your
vehicle .

210 Tires an d whee ls
Tires and wheels
Tires
General notes
Tires may be the least appreci­
ated and most abused parts of
a motor vehicle.
Ti res may be the least appreci­
ated and most abused parts of
a motor vehicle. Tires are, how­
ever, one of the most important
parts of a vehicle, particularly
considering the comparatively
small patch of r ubber on each
tire that assures that all-impor­
tant contact between you, your
vehicle and the road.
Maintaining the co rrect tire
p ressure, making sure that your
vehicle and its tires do not have
to carry more we ight than they
can safe ly handle, avoiding
damage from road hazards and
regularly inspecting tires for
damage including cuts, s lashes
irregular wear and overall con ­
d ition are the most important
things that you can do to help
avoid sudden tire failure inc lud­
ing tread separation and blow­
outs.
Avoiding damage
If you have to drive over a curb
or similar obstacle, drive very
slowly and as close as possible
at a right angle to the curb.
Always keep chemicals includ­
ing grease, oil, gasoline and
brake fluid off the tires.
Inspect the tires regularly for
damage (cuts, cracks or blis­
ters, etc.). Remove any foreign
bodies embedded in the treads.
Storing tires
Mark tires when you remove
them to indicate the direction
of rotation. This ensures you to be able to mount them correct ­
ly when you reinstall them.
When removed, the wheels or
tires should be stored in a cool,
dry and preferably dark p lace.
Store tires in a vertical position if they are not mounted on
rims, in a horizontal position if
they are mounted on rims.
New tires
New tires have to be broken in
¢ &.
The tread depth of new tires
may vary, according to the type .,.

M N
er
u..
co ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Bead
means the part of the tire that
is made of steel wires, wrapped
or reinforced by ply cords and
that is shaped to fit the rim.
Bead separation
means a breakdown of the bond
between components in the
bead.
Cord
means the strands forming the
plies in the tire .
Cold tire inflation pressure
means the tire pressure recom­
mended by the vehicle manu­
facturer for a tire of a designat­
ed size that has not been driven
for more than a couple of miles (kilometers) at low speeds in
the three hour period before
the tire pressure is measured or
adjusted.
Curb weight
means the weight of a motor
vehicle with standard equip­
ment including the maximum
capacity of fuel, oil, and cool­
ant, air conditioning and addi­
tional weight of optional equip­
ment.
Tires and wheels 213
Extra load tire
means a tire design to operate
at higher loads and at higher inflation pressures than the
corresponding standard tire. Extra load tires may be identi­
fied as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Gross Axle Weight Rating ("GAWR")
means the load-carrying capaci­
ty of a single axle system,
measured at the tire-ground in­
terfaces.
Gross Vehicle Weight Rating ("GVWR")
means the maximum total
loaded weight of the vehicle.
Groove
means the space between two
adjacent tread ribs.
Load rating (code)
means the maximum load that
a tire is rated to carry for a giv­
en inflation pressure. You may
not find this information on all
tires because it is not required by law.
•
•
'

important parts of the vehicle
and can lead to sudden tire fail­
ure, including a blowout and
sudden deflation that can cause
the vehicle to crash.
Your safety and that of your
passengers also depends on
making sure that load limits are not exceeded. Vehicle load in­
cludes everybody and every­
thing in and on the vehicle.
These load limits are technical­ ly referred to as the vehicle's
Gross Vehicle Weight Rating
("GVWR").
The "GVWR" includes the
weight of the basic vehicle, all
factory installed accessories, a
full tank of fuel, oil, coolant and other fluids plus maximum
load. The maximum load in­
cludes the number of passen­
gers that the vehicle is intend­
ed to carry ("seating capacity")
with an assumed weight of 150 lbs . (68 kg) for each pas­
senger at a designated seating
position and the total weight of
any luggage in the vehicle. If
you tow a trailer, the weight of
the trailer hitch and the tongue
weight of the loaded trailer
Tires and wheels 225
must be included as part of the
vehicle load.
The
Gross Axle Weight Rating
("GAWR") is the maximum load
that can be applied at each of
the vehicle's two axles.
The Gross Vehicle Weight Rat­ ing and the Gross Axle Weight
Rating are listed on the safety
compliance sticker label locat­
ed on the driver's side 8-pillar.
Your Audi has 4 seating posi­
tions, 2 in the front and 2 in the rear for total seating capacity
of 4. Each seating position has
a seat belt¢ page 123, Safety
belts.
The fact that there is an upper limit to your vehicle's Gross Ve­
hicle Weight Rating means that
the total weight of whatever is being carried in the vehicle (in­
cluding the weight of a trailer hitch and the tongue weight of
the loaded trailer) is limited.
The more passengers in the ve­ hicle or passengers who are
heavier than the standard
weights assumed mean that less weight can be carried as
luggage.
•
•
'