warning AUDI RS7 SPORTBACK 2015 Owners Manual

218 Check ing and filling
fig . 188. With a cold engine, the coo lant
l evel should be between the "min" and
"max" markings . When the engine is warm ,
the leve l may be slightly above the "max"
mark ing .
The location of the coolant expansion tank
can be seen in the engine compartment illus­
tration
9 page 213.
To obtain an accurate reading, the engine
must be switched off .
The expans ion tank in you r vehicle is equipped
with an e lectric coolant level sensor.
When the coolant level is too low, the warning l ight in the Auto-Check System
9 page 15 w ill
illum inate unti l you add coolant and the level
has been restored to normal. Even though
there is an electric coolant level senso r, we
still recommend you check the coolant leve l
from time to time .
Coolant loss
Coolant loss may indicate a le ak in the cooling
system . In the event of coolant loss, the cool ­
ing system should be inspected immediately
by your authorized Audi dealer. It is not
enough merely to add coolant.
I n a
s ealed system, losses can occur only if
the boiling point of the coolant is exceeded as
a result of overheating.
A WARNING
The cooling system is under pressure and can get very hot. Reduce the risk of scald­
ing from hot coolant by followi ng these
steps .
- Turn off the engine and allow it to coo l
down.
- Protect your face, hands and arms from
escaping fluid and steam by covering the
cap with a large, thick rag .
- Turn the cap slowly and very carefu lly in
a counter-clockwise direction w hile ap­
plying light, downward pressure on the
top of the cap . -
To avoid being burned, do not spi ll anti­
freeze or coolant on the exha ust system
or hot engine parts. Under certain cond i­
tions, the ethylene glycol in engine coo l­
a nt can catch fire.
(D Note
Do not add any type of radiator leak sea l­
ant to your veh icle's engine coolant. Add­
i ng radiator repair fluid may adverse ly af­
fect the funct ion and pe rformance of you r
cooling system and could result in damage
not cove red by your New Veh icle Limited
War ran ty.
Adding coolant
Be very careful when adding engine coolant.
Befo re you check anyth ing in the eng ine com­
partment,
always read and he ed all WARN­
INGS ¢ ..&. in Working in the engine compart­
ment on page
211.
" Requirement: There must be a residua l
amo unt of coolant in the expansion ta nk
¢ (D .
"Tu rn off the engi ne.
" Le t the eng ine cool down.
" Place a thick rag over the coolant expansion
t ank
9 page 217, fig. 191 and ca refully
twist the cap counter-clockwise ¢&,, .
" Add coolant m ixed in the correct rat io
¢
page 217, Coolant up to the MAX mark­
ing.
" Make sure that the flu id leve l remains sta -
ble . Add more coo la nt if necessary .
" Twist the cap o n again
tightly .
Replacement engine coo lant must conform to
exact spec ificat ions ¢
page 217, Coolant.
We recommend using only coolant add i-
tive
Gl2++, Gl3 or in an emergency Gl2 +. Do
not use a d ifferent addit ive . In an emergency
use p la in water until you can get the correct
additive and can resto re the co rrect rat io . This
shou ld be done as soon as possib le. .,..

M N
0:: <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
If you have lost a consi derable amount of
coolant, then you should add co ld antifreeze
and cold water only when the engine is co ld .
Always use
new engine coolant when refi lling.
D o not fi ll coolant above the "MAX " mark . Ex­
cess coolant will be forced out th rough the
p ress ure rel ief valve in the cap when the en­
g ine becomes hot .
A WARNING ,_________
-The cooling system is under press ure and
can get very hot . Reduce the risk of
sca ld ing from hot coo lant by following
these steps.
- Tur n
off the eng ine and a llow itto cool
down.
- Protect your face, hands and arms from
escap ing f lu id a nd steam by cover ing
the cap wi th a la rge, thick rag.
- Turn the cap slow ly and very ca refully
in a cou nte r-clockw ise d irect ion while
a pply ing ligh t, downw ard p ress ure on
the to p of the cap.
- To avo id being burned, do no t sp ill an­
tifreeze or coolan t on t he exhaust sys­
tem or ho t engine parts . U nder certa in
conditions, the ethylene glyco l in en­
gine coolant can catc h fire .
- Antifreeze is poisonous . Always store an ­
tifreeze in its original container and we ll
o ut o f the reach of children.
- If you drain the coolant , it must be
caught and safely stored in a proper con­
tainer clearly marked "poison".
@ Note
- Do not add coolant if the expansion tank
i s empty . Ai r could enter the cooling sys­
tem and damage the engine. If this is
the case, do not continue driving. Seek professional assistance.
- Coolant po llutes the env ironment and
could cause a n engine fire. Excess coo l­
ant wi ll be forced out through the pres­
sure re lief valve in the cap when the en ­
gine becomes hot.
Checkin g and fillin g 219
-If, in an emergency, on ly wate r can be
added, the correct ratio between water
and antifreeze ¢
page 217 must be re­
stored as soon as possible.
@) For the sake of the environment
Drained coolant sho uld not be reused. A l­
ways d ispose of used coolant while observ­
i ng a ll environmental regulations.
, Radiator fan
The radiator fan switches on automatically by
itself .
An auxiliary electric radiato r fan switches on
and
off depending on coolant temperature
and othe r vehicle ope rat ing cond it ions.
After yo u switch the eng ine o ff, the aux iliary
f an can continue running for up to 10 m inutes
- even with the ignition off. It can even switch
on aga in later by itself¢ .&. , if
- the temperatu re of the engine coo lant rises
du e to the h eat build -up from th e engin e in
the engine compa rtment, or
- the engine compa rtment heats up because
the vehicle is parked in intense sunlig ht.
A WARNING ~
- To reduce the risk of persona l inju ry nev-
er touch the radiator fan .
- The a uxiliary electric fan is tempe rat ure
contro lled and can switch on suddenly
even when the engine is not running.
- The a uxiliary radiator fan sw itches on a u­
tomatically when the engine coo lant
reaches a certai n temperature and will
continue to ru n until the coo lant temper­
ature drops. •
•

220 Checking and filling
Brake fluid
Checking brake fluid level
Fig . 192 Engine compar tment: cove r on the brake fl uid
reservo ir
Before you check anything in the engine com­
partment,
always read and heed all WARN­
INGS ¢&. in Working in the engine compart­
ment on page 211.
,.. Read the brake fluid level from the brake
fluid reservoir¢
fig . 192, ¢ page 213,
fig. 188 .
The brake fluid level must be be­
tween the "MIN" and "MAX" markings.
The location of the brake flu id reservoir can be
seen in the engine compartment illust rat ion
¢ page 213.
The fluid level may drop slightly after some
time due to the automatic adjustment of the
brake pads. This is not cause for alarm.
If the brake fluid level falls
considerably be­
low the "MIN" mark, the brake warning/indi­
cator light . (U.S. models)/ . (Canadian
models) will come on ¢
page 14. Do not con­
tinue to operate the vehicle. The comp lete
brake system shou ld be thoroughly checked
by an authorized A udi dealer or other quali­
fied facility and the cause corrected.
If the
brake fluid level is too low, the brake warning/
indic ator light will illuminate. Contact an au­
thorized Audi dealer
immediately .
Changing brake fluid
Have the brake fluid changed by an experi­
enced technician .
Brake fluid absorbs moisture from the air. If
t he water content in the brake fluid is too
high, corrosion in the brake system may result
after a period of time . The boiling point of the
brake flu id will also decrease conside rably and
decrease braking pe rformance.
Therefore, the brake fluid must be changed
every two years . Always use new brake flu id
which conforms to Federal Motor Vehicle
Standard "FMVSS 116 DOT 4".
The brake fluid reservoir can be difficult to
reach, therefore, we recommend that you
have the brake fluid changed by your author­
ized
Audi dealer. Your dealer has the correct
tools, the right brake fluid and the know-how
to do this for you.
A WARNING
- Brake fluid is poisonous . It must be stor­
ed only in the closed original container
out of the reach of children!
- Brake failure can resu lt from o ld or inap­
propriate brake fluid. Observe these pre­
cautions:
- Use only brake fluid that meets SA E
specification
J 1703 and conforms to
Federal Motor Vehicle Standard 116.
Always check with your authorized Audi
dealer to make sure you are using the
correct brake fluid. The correct type of
brake f luid is also indicated on the
brake fluid reservoir.
- The brake fluid must be new. Heavy use
of the brakes can cause a vapor lock if
the brake fluid is left in the system too
long . This can seriously affect the effi­
c ie ncy of the brakes as well as your
safety. This could resu lt in an accident.
(D Note
Brake fluid will damage the paint of your
vehicle .

M N
0:: <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
@ For the sake of the environment
Because of the pr oblem of proper d isposa l
of brake flu id as we ll as the special tools
requ ired and the necessary expert ise, we
recommend that you have the brake fluid
changed by your author ized Audi dealer .
Battery
General information
Under normal operating conditions, the bat­
tery in your Audi does not need any mainte ­
nance. With
high outside temperatures or
long daily dr ives we recommend that you have
the electro lyte level checked by a service fa­
cility . The electrolyte level shou ld also be
checked each time the battery is charged
¢ page 223.
Have the battery checked when you take your
ve hicle in for service . You are well adv ised to
replace a battery that is older than 5 yea rs .
W ith certa in types of a irbag deployment, t he
b attery is d isconnected from the vehicle elec­
tr ica l system for safety reasons¢.&.
in Re ­
pair, core and disposal of the airbags on
page 155.
Disconnecting the battery terminals
Some vehicle functions (power w indow regu­
lators , for example) are lost if the battery ter­
m inals a re d isconnected. These func tions have
to be re lea rned after the batte ry term inals a re
connected agai n. T o prevent this , the bat tery
should only be d isconnec ted from the vehicle
e lec tric al system when absolu tely necessa ry
for repairs .
Vehicles not driven for long periods
If you do not drive you r vehicle over a period
of severa l days or weeks, elec trical compo­
nen ts are gr adually cut b ack o r swi tched off .
This redu ces energy cons umption and main­
tains starting capab ility over a longer per io d
¢
page 193. Some of the co nvenience func­
tions may not operate, s uch as the inte rior
lights or power seat adjustme nt. The conven-
Checkin g and fillin g 221
ience funct ions w ill be available again when
yo u sw itch on the ign ition and start the en­
gine.
Winter operation
D ur ing the w inte r mon ths, bat tery ca pa city
tends to decrease as tempera tures drop . This
is beca use more power is a lso consumed wh ile
starting, and the headlights, rear window de­
fogger, etc., are used mo re often.
Avoid unnecess ary powe r consumpt ion, pa r­
ticu lar ly in city traffic o r when traveling only
sho rt distances. Let yo ur authorized A udi
dealer check the capacity of the vehicle bat ­
tery before w inter sets in¢
page 223 . A well
charged battery will no t on ly prevent star tin g
problems w hen the weather is cold, but w ill
also last longer .
@ Tips
If your vehicle is left standing for seve ral
weeks at extremely low temperatures, the
vehicle battery s hou ld be removed and
stored where it will not freez e. This will
p reve nt it from be ing dam aged and having
to be repl aced .
Working on the battery
Be especially careful when working on or near
the bat tery.
The battery is located in the luggage compar t­
ment under the floor . B efo re you che ck any­
thi ng in the luggage compartment,
read and
heed all WARNINGS
¢ .&, .
Always heed the safety warnings , when work­
i ng on the veh icle batte ry or t he vehicle e lec­
t rical sys tem to p reven t inju ry.
The following WARNINGS are very
important when working on the battery:
Always heed the following WARNING SYM· BO LS and safety precautions when working
on the battery .
®
Always wear eye protection.
•
•

222 Check ing and filling
&
Batt ery aci d c ont ain s s ulfuric acid .
A lw ay s w ear gloves and eye protec-
ti on.
@
No
- spark s
- flame s
· sm okin g.
A
When a b atte ry is ch arged , it p rodu -
ce s hydr oge n ga s wh ich i s ex plosi ve
.
and co uld cause pe rsonal injur y.
®
Alway s keep the batt ery well out of
re ach of children.
A WARNING
Whenever working on the battery or on
the electrical system, there is the r isk of
injury, acc ident and even fire. Read and
heed the following WARNINGS:
- Always wear eye protection. Do not let
battery acid or any lead part icles get on
your sk in or cloth ing . Sh ield your eyes .
Explosive gases can cause blindness or
other injury.
- Battery acid contai ns sulfur ic acid. Sulfu­
ric acid can cause blindness and severe
burns.
- Always wear gloves and eye protection.
Do not tilt the battery because ac id
could leak out of the vent ilation open­
ings.
- If you get battery acid in your eyes or
on your sk in, immediately rinse with
cold water for severa l m inutes and get
medical attention .
- If you should ingest any battery acid,
seek medical attention immediately .
- Do not expose the battery to an open
flame, electric sparks or an open light.
- Do not smoke.
- Do not interchange the positive and neg-
ative cab les.
- When working on the battery, be sure
not to short-circuit the terminals with
tools or other metal objects. This would
cause the battery to heat up very quickly,
wh ich could lead to damage or explosion
and personal injury. -
When a battery is charged, it produces
hydrogen gas which is explosive and
could cause personal injury.
- Always keep the battery well out of the
reach of children.
- Before work is done on the electrical sys­
tem, disconnect the negat ive ground ca­
ble.
- Before performing any work on the e lec­
trica l system, switch off the engine and
ignit ion as well as any electrical equip­
ment. The negative cable on the battery
must be disconnected .
If you are just go­
ing to replace a light bulb, then it is
e nough to swi tc h off the lights.
- Before disconnecting the battery, switch
off the anti-theft alarm system! Other­
wise you wi ll set off the alarm.
- When disconnecting the battery, f irst
d isconnect the negat ive cab le and then
the posit ive c ab le.
- Before reconnecting the batte ry, ma ke
sure all e lectr ica l consumers are sw itch­
ed off . Re connect the pos it ive cable first
and then the negative cable. Never inter ­
change the cables - this could start a fire!
- Never charge a frozen or a thawed-out
battery. It could exp lode! If a battery has
frozen, then it must be replaced . A dis­
charged battery can freeze over at 32
°F
(0 oc).
- Make sure the vent hose is always attach­
ed to the opening on the s ide of the bat­
tery.
- Never use batteries which are damaged.
There is the danger of an explosion! Al­
ways rep lace a damaged battery.
A WARNING
Ca lifornia Proposition 65 Warning:
- Battery posts, terminals and related ac­
cessories conta in lead and lead com­
pounds, chemicals known to the State of
California to cause cancer and reproduc­
tive problems . Wash hands after han-
dling.
~

"' N
a:: I.J ""'. rl I.O
"' rl
"' rl
(D Note
- Do not disconnect the ve hicle battery
when the ignition is on or when the en­
gine is running, otherwise, you will dam­
age electronic components in the electri­
ca l system .
- If your vehicle is going to stand for a
l ong period of time without being driven,
protect the battery from "freezing", oth ­
erwise it w ill be damaged and w ill then
have to be replaced .
- When opening the doors, the windows
l ower app rox imately 10 mm automati­
cally. This f unction is not available when
t h e battery is disconnec ted, wh ic h
means there is a ris k t hat the door se al
or the w indow co uld be damaged .
Battery charging
Starting the engine requires a well charged bat tery.
F ig. 1 93 En gine co mpartme nt: c onnectors for a charg­
er a nd jum p sta rt cable s
Always read and heed all WARNINGS below
¢ .&. and
¢.&. in Working an the battery on
page 2 22.
"'Switch off the ignit ion and all electrica l con­
s u mers .
"' Make sure the area is well vent ilated when
you charge the battery.
"' Open the engine hood
c::> page 211 .
"'Open the red cover o n the posit ive pole
<=> fig . 193.
"' Connect the charger connectors accord ing to
the instruc tions to the
jump start bolts .
(Bolts under the red cover = "positive", Bolts
with hex head = "nega tiv e").
Checkin g and fillin g 223
"'On ly now plug the mains lead for the cha rg ­
i ng eq uipment into the wa ll outlet and turn
it on
c::> ,&. .
"'Make sure the charging rate is not o ver
30 amps /14.8 Volt .
"'When the battery is fully c harged : Turn the
charg ing equipment off and remove the
mains lead from the wa ll out let .
"' Now remove the clamps fo r the cha rg ing
equ ipme nt.
"' Close the red cover on the positive pole .
"' Close the hood ¢
page 212 .
A d ischa rged batte ry can freeze at tempe ra­
tures of only 3 2 F
0 (0 °C). Allow a fro zen bat­
te ry to thaw completely before attemp ting to
c h arge it
c::> & . However, we recommend not
using a thawed battery again because the bat­
tery casing can be cracked due to ice forma­
tion and can leak battery ac id.
Battery charging (Maximum charging rate
of 30 amps /14.8 Volt )
When cha rging at
low vo ltages (e .g. with a
trickle charger), the batte ry cables do not
have to be disconnected f irst . The battery
caps should
not be ope ned when charg ing a
batte ry .
It is not necessary to remove the battery from
the luggage compartment, and it is a lso not
necessary to d iscon nect the cab les .
Fa st charging the battery (cha rging rate
above 14.8 Volts)
Fo r technical reasons do not use a battery
c h a rger that uses voltage g reater than 14 .8
Volts to charge yo ur vehicle's battery .
A WARNING
C harging a battery can be dangero us.
- Always follow t he ope rati ng inst ructions
provi ded by the battery cha rg er ma nu­
f ac turer when chargi ng you r battery.
- N ever cha rge a fro zen batte ry.
It may ex­
p lode because of gas trapped in the ice .
A llow a froz en ba tte ry to thaw out first.
- D o not r euse ba tte ries wh ich were fro­
z en. The bat tery housi ng may
h ave

224 Check ing and filling
cracked an d weake ned when the battery
froze.
- Charge the battery in a we ll ventilated
area. Keep away from open flame or elec­
trical spark . Do not smoke. Hydrogen gas
generated by the battery is exp losive.
- To reduce the danger of explosion, never
connect or disconnect charger cables
wh ile the charger is operating .
- Fast charg ing a battery is dangerous and
should only be attempted by a compe­
tent technician w ith the proper equip ­
ment .
- Battery acid that may spill d uring charg­
ing should be washed off w it h a solution
of warm water and ba kin g soda to neu­
t rali ze the acid.
~ Note
Never use a fast charger as a booster to
start the engine. This will seriously dam ­
age sensitive ele ct ronic components, such
as co ntrol units, relays, rad io, etc. , a s we ll
as th e batte ry charge r.
Battery replacement
The new battery must have the same specifi­
cations and dimensions as the original equip­
ment battery.
I ntell igent energy manag ement in your veh i­
cle is respo nsible for d ist ribu ting the e lectr i­
cal energy throughou t you r vehi cle
~ page 193. The inte lligen t energy m anage­
ment system w ill keep the engine batte ry
charged better than vehicles w it h out t his sys­
tem . T o make sure the additional e lectrical en ­
ergy is available once again after you have
changed t he battery, we recommend that you
install batteries of the same type and manu ­
facture only (the same as those ins talled at
the t ime your vehicle was delivered). Specifi­
cations a re listed o n the battery hous ing. You r
author ized de aler m ust code the b attery in
the ene rgy management system to enable yo u
to use the energy managemen t fu nctions co r­
rectly after replac ing the battery. T
he new battery must have the same capacity,
vo ltage ( 12-volts) , amperage , construction
and plug sea ling .
When ins tall ing t he battery, make su re the ig­
nition and a ll elect rical consume rs are switch ­
ed off .
(D Note
M ake sure the ven tilat ion hose on the side
of the ba ttery is connecte d, otherwise
fumes or batte ry acid can lea k out .
@ For the sake of the environment
B ecause o f the p rob lem of p roper disposal
of a battery, we recommen d your author ­
i zed Audi dea ler chan ge the battery for
you . Batteries contain sul fur ic acid and
l ead and must a lways be disposed of p rop­
e rly in compliance with all environmental
regulations . Disposing of vehicle batter ies
i mprope rly is very dange rous to th e envi ­
r o nment.
Windshield/headlight*
washer container
Fi g. 19 4 En gin e co mpa rt m en t: cove r on t he w inds hield
a n d head ligh t* was her fl ui d reservo ir
T he washer fluid co ntai ner is mar ked w it h t he
symbol$ on its cap
~ fig. 194, ~page 213,
fig . 188.
.,. Before you chec k any thing in the engine
comp artment,
always read and heed all
WARNINGS ~ A in Working in the engine
compartment on page 211 .
.,. Lift the fi ller cap tongue to add washer flu -
id. You can f ill the container to the top. ..,.

Tires and wheels 22 7
and make of tire and the tread -New tires tend to be slip-•
pattern. pery and must be broken in. • '
Hidden damage To reduce the risk of losing
Damage to tires and rims is of- control, a collision and seri-
ous personal injuries, drive
ten not readily visible. If you with special care for the
notice unusual vibration or the first 350 miles (560 km).
vehicle pulls to one side, this
-Driving with worn or dam-
may indicate that one of the
aged tires can lead to loss of
tires has been damaged. The
control, sudden tire failure,
tires must be checked immedi-
ately by an authorized Audi including a blowout and
sudden deflation, crashes
dealer or qualified workshop.
and serious personal inju-
Unidirectional tires ries. Have worn or damaged
A unidirectional tire can be tires replaced immediately.
identified by arrows on the -Tires age even if they are
sidewall, that point in the di rec- not being used and can fail
tion the tire is designed to ro- suddenly, especially at high
tate. You must follow the speci- speeds. Tires that are more
fied direction of rotation. This is than 6 years old can only be
necessary so that these tires used in an emergency and
can develop their optimum then with special care and
characteristics regarding grip, at low speed.
road noise, wear and hydro- -Never mount used tires on
planing resistance. For more in- your vehicle if you are not
formation
¢ page 268. sure of their "previous histo-
ry." Old used tires may have
A WARNING
been damaged even though -
New tires or tires that are the damage cannot be seen
old, worn or damaged cannot that can lead to sudden tire
provide maximum control failure and loss of vehicle
M N and braking ability. 0:: control. <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,

Recommended inflation
pressure
see¢ page 229J Cold tire infla­
tion pressure.
Reinforced tire
means a tire design to operate
at higher loads and at higher
inflation pressures than the
corresponding standard tire. Reinforced tires may be identi­
fied as "XL", "xl", "EXTRA
LOAD", or "RF" on the sidewall.
Rim
means a metal support for a
tire or a tire and tube assembly
upon which the tire beads are
seated.
Rim diameter
means nominal diameter of the
bead seat. If you change your
wheel size, you will have to pur­ chase new tires to match the
new rim diameter.
Rim size designation
means rim diameter and width.
Rim width
means nominal distance be­
~ tween rim flanges.
0:: <.J 'SI: ,...., \!) 1.1'1 ,...., 1.1'1 ,....,
Tires and wheels 231
Sidewall
means that portion of a tire be­
tween the tread and bead.
Speed rating (letter code)
means the speed at which a tire
is designed to be driven for ex­
tended periods of time. The rat­ ings range from 93 mph (150
km/h) to 186 mph (298 km/h)
¢
page 248. You may not find
this information on all tires be­ cause it is not required by law.
The speed rating letter code,
where applicable, is molded on
the tire sidewall and indicates
the maximum permissible road speeds ¢
A in Winter tires on
page 252.
Tire pressure monitoring system
means a system that detects
when one or more of a vehicle's tires are underinflated and illu­
minates a low tire pressure
warning telltale.
Tread
means that portion of a tire
that comes into contact with
the road.
•
•
'

236 Tires and wheels
Because technical changes may
be made to vehicle equipment
during the model year, always
compare the tire size designa­
tion on the tire pressure label
on your vehicle with the tires on
your vehicle . Make sure that the
tire size information on the ve­ hicle label is the same as the
size of the tires on the vehicle .
This is especially important if
the vehicle belongs to someone else or you bought the vehicle
with different rims/tires or you bought the vehicle as a previ ­
ously owned vehicle.
Remember, your safety and
that of your passengers also de­ pends on making sure that load
limits are not exceeded . Vehicle
load includes everybody and ev­
erything in and on the vehicle .
These load limits are technical­ ly referred to as the vehicle's
Gross Vehicle Weight Rating
("GVWR"). The Gross Axle
Weight Rating ("GAWR") is the
maximum load that can be ap­
plied at each of the vehicle's
two axles . The Gross Vehicle
Weight Rating and the Gross
Axle Weight Rating are listed on the safety compliance stick- er label located on the driver's
side B-pillar. The tire pressure
label on your Audi lists the
maximum combined weight of
all of the occupants and lug­
gage or other cargo that the ve­
hicle can carry. For the location
of the tire pressure label
¢ fig. 195.
&_ WARNING
-
Overloading a vehicle can
cause loss of vehicle control,
a crash or other accident, se­
rious personal injury, and
even death .
- Carrying more weight than
your vehicle was designed to carry will prevent the ve­
hicle from handling properly
and increase the risk of a
loss of vehicle control.
-The brakes on a vehicle that has been overloaded may
not be able to stop the vehi­
cle within a safe distance.
- Tires on a vehicle that has
been overloaded can fail
suddenly causing loss of
control and a crash.
-Always make sure that the total load being transported
does not make the vehicle .,.