clock AUDI S8 2008 User Guide
[x] Cancel search | Manufacturer: AUDI, Model Year: 2008, Model line: S8, Model: AUDI S8 2008Pages: 404, PDF Size: 52.7 MB
Page 318 of 404

___ C_ h_e _c _ k_ i_ n ~g~ a_ n_ d_ f_ i_ll _in _g~--------------------------------------------
&, WARNING (continued)
• Turn off the engine and allow it to cool down.
• Protect your face, hands and arms from escaping fluid and
steam by covering the cap with a large, thick rag.
• Turn the cap slowly and very carefully
in a counter-clockwise
direction while applying light, downward pressure on the top of
the cap.
• To avoid being burned, do not spill antifreeze or coolant on the
exhaust system or hot engine parts. Under certain conditions, the
ethylene glycol in engine coolant can catch fire.
0 Note
Do not add any type of radiator leak sealant to your vehicle's engine
coo lant. Adding radiator repair fluid may adversely affect the func
tion and perfo rmance of your cooling system and could result in
damage not covered by your New Vehicle Limited Warranty .
[ i] Tips
On vehicles with the 12-cylinder engine, the expansion tank is
located under a cover. •
Adding coolant
Be very careful when adding engine coolant.
Before you check anything in the engine compartment,
always read and heed all WARNINGS => & in "Wor king in
the engine compartment" on
page 307.
-Turn off the engine.
-Let the engine cool down.
-Place a thick rag over the coolant expansion tank
=> page 315, fig. 267 and carefully twist the cap counter
clockwise
=> & .
-Add coolant.
-Twist the cap on again tightly.
Replacement engine coolant must conform to exact specifications
=> page 314, "Coolant". Even in an emergency, if coolant additive
G12++, G12+ or G12 is not available, do
not use a different additive.
Use plain water instead until you can get the correct additive and
can restore the correct ratio. This should be done as soon as
possible.
If you have lost a considerable amount of coolant, then you should
add cold antifreeze and cold water only when the engine is cold.
Always use
new engine coolant when refilling.
Do not fill coolant above the "MAX" mark. Excess coolant will be
forced out through the pressure relief valve in the cap when the
engine becomes hot.
& WARNING
• The cooling system is under pressure and can get very hot.
Reduce the risk of scalding from hot coolant by following these
steps.
-Turn off the engine and allow it to cool down.
- Protect your face, hands and arms from escaping fluid and
steam by covering the cap with a large, thick rag.
- Turn the cap slowly and very carefully
in a counter-clockwise
direction while applying light, downward pressure on the top
of the cap.
- To avoid being burned, do not spill antifreeze or coolant on
the exhaust system or hot engine parts. Under certain condi-
tions, the ethylene glycol in engine coolant can catch fire. .,,
Page 352 of 404

llffl!I What do I do novv?
'---------------------------------------------
Tools
The vehicle tools are stored in the luggage compartment
lid.
Fig . 281 Trunk lid:
Opening the cover
Fig . 282 Trunk lid:
Vehicle tools
-To open the cover, turn the retainer in the direction of the
arrow and pull the cover down
~ page 350, fig. 281.
The onboard tool kit includes:
• Hook for removing wheel covers *
• Plastic hook to remove wheel bolt covers
• Whe el bolt wr ench
• Alignment pin for changing wheels
• Screwdr iv e r with reversible blade •
10 x 13 open ended wrench
• Towing loop
[ i] Tips
Some of the on board items listed above are provided on certain
models only or are optional extras .•
Spare wheel
The spare wheel is stored in the wheel well underneath
the floor panel in the luggage compartment.
Fig . 283 Luggage
compartment spare
wheel
Your vehicle is equipped with a regular spare wheel. It is
held in place by plastic retaining knurled screw.
Taking out the spare wheel
- Raise the floor panel at the plastic handle.
- Securely engage the handle in the luggage compartment
seal as illustrated to keep the floor panel up.
- Unscrew the knurled retainer bolt in the wheel center
~ fig. 283. Turn it counter-clockwise .
- Take out the spare wheel.
Page 353 of 404

What do I do now? Ill
------------------~;___
•
-Disengage and lower the floor panel before you close the
luggage compartment lid again.
Storing the replaced wheel
-Place the replaced wheel inside the spare wheel well in
the luggage compartment.
Tighten the knurled retaining screw clockwise to secure
the wheel in place.
-Disengage and lower the floor panel before you close the
luggage compartment lid again.
& WARNING
Loose items in the passenger compartment can cause serious
personal injury during hard braking or in an accident .
• Never store the spare wheel or jack and tools in the passenger
compartment.
• Always store all jacking equipment, tools, and the spare wheel
in the luggage compartment .
• Tighten the knurled retaining screw for the spare wheel
securely.
[ i] Tips
Check the inflation pressure of the spare tire periodically to keep the
tire ready for use. •
Changing a wheel
Before changing a wheel
Observe the following precautions for your own and your
passenger's safety when changing a wheel.
-After you experience a tire failure, pull the car well away
from moving traffic and try to reach level ground before
you stop
~ &,. .
-All passengers should leave the car and move to a safe
location (for instance, behind the
guardrail) ~&,. .
-Engage the parking brake to prevent your vehicle from
rolling
unintentionally ~&,. .
-Move selector lever to position P ~ &,..
-If you are towing a trailer: unhitch the trailer from your
vehicle.
-Take the jack and the spare tire out of the luggage
compartment~ page 349.
& WARNING
You or your passengers could be injured while changing a wheel if
you do not follow these safety precautions:
• If you have a flat tire, move a safe distance off the road. Turn off
the engine, turn the emergency flashers on and use other warning
devices to alert other motorists.
• Make sure that passengers wait in a safe place away from the
vehicle and well away from the road and traffic.
• To help prevent the vehicle from moving suddenly and possibly
slipping off the jack, always fully set the parking brake and block
the wheel diagonally opposite the wheel being changed. When one _..
Do -it -yourself service
Page 356 of 404

lll'I....__W_ h_ a
_ t_d_ o_ l _d _o_ n_ o_ vv_ ? ______________________________________________ _
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising the
vehicle .
Loosening
Fig . 28 6 Chang in g a
w hee l: loos enin g t he
whee l bolts
-Install the wheel bolt wrench over the wheel bolt and
push it down as far as it will go.
Take tight hold of the
end of the wrenc h handle and turn
the wheel bolts counter-clockwise about
one single turn
in the direction of
arrow =:> fig. 286.
Tightening
-Install th e wheel bolt wren ch over the wheel bo lt and
push it down as far as it w ill go .
- Take tight hold o f the
end of th e w re n ch handle and tur n
each wheel bolt clockwi se until it is seated.
& WARNING
• Do not u se fo rc e or hu rry when changi ng a whe el -you c an
ca use th e vehicle to slip off the jack and c ause ser iou s pers onal
injurie s.
& W AR N IN G (c ontinu ed )
• Do not loo sen th e wheel b olt s m ore than one turn before you
rai se the vehicle w ith the jack .
-You ris k an inju ry.
[ i] Tips
• Never use the hexagonal socket in the handle of the screwdriver
to loosen or tighten the wheel bolts .
• If a wheel bo lt is very tight, you may find it easier to loosen by
carefully pushing down on the end of the wheel bolt wrench with
one foot only . As you do so, hold on to the car to keep your balance
and take care not to slip. •
Raising the vehicle
The vehicle must be lifted with the jack first before the
wheel can be removed.
Fig . 287 C ha ng ing a
w he el: m ounting
poi nts for th e jac k ..
Page 358 of 404

lll'IL--____:W...:...;. h.:..: a::.. t:....: d.:..:o:....:. l...; d::.. o
..:.... n;..:..:: o...;w ...:...;. ? ____________________________________________ _
Taking the wheel off /installing the spare
Follow these instructions step-by-step for changing the
wheel
Fig . 289 Changing a
wheel: using the
screwdriver handle
!with the blade
removed) to turn the
bolts
Fig . 290 Changing a
wheel: alignment pin
inside the top hole
After you have loosened all wheel bolts and raised the
vehicle off the ground, remove and replace the wheel as
follows:
Removing the wheel
- Use the hexagonal socket in the screwdriver handle to
completely remove the topmost wheel bolt and set it
as ide on a
cl ean surface => fig. 289. -
Screw the threaded end of the
alignment pin from the
tool kit hand-tight into the empty bolt
hole => fig. 290.
- Then remove the other wheel bolts as described above .
- Take off the wheel leaving the alignment pin in the bolt
hole.
Putting on the spare wheel
- Lift the spare wheel and carefully slide it over the align
ment pin to guide it in place.
- Use the hexagonal socket in the screwdr iver handle to
screw in and tighten all wheel bolts
slightly.
- Remove the alignment pin and insert and t ighten the
remaining wheel bolt slightly like the rest.
- Turn the jack handle counter-clockwise to lower the
vehicle until the jack is fully released.
- Use the wheel bo lt wrench to tighten all wheel bolts
firmly=> page 354. Tighten them crosswise , from one
bolt to the (approximately) opposite one, to keep the
w heel centered .
[ i ] Tips
Never use the hexagonal socket in the handle of the screwdriver to
loosen or tighten the wheel bolts .
• Pull the reversible blade from the s crewdriver before you use the
hexagonal socket in the handle to turn the wheel bolts.
• When mounting tires with
unidirectional tread design make sure
the tread pattern is pointed the right way ::::>
page 357.
• The wheel bolts should be clean and easy to turn . Check for dirt
and corrosion on the mating surfaces of both the wheel and the -.,
Page 391 of 404

Alphab eti ca l ind ex I'll
----------------------------------------- -'---------
Climate controls ............. .... ... 114
Air distribution ... .... .... .... .... 120
Air outlets ..... .. .... .... .... .... 122
Air outlets (rear) .... ... .... .... ... 122
Air recirculation .. .... .... ... .... . 121
AUTO (standard setting) ...... .... . 117
Basic se ttings ... .. .... ... .... .... 1 26
Cen ter ai r vent . ....... ... .... .... 127
Contro ls ... .. .... .... ... .... .... 116
Defrosting/defogging ..... ... .... . 120
Description ... .... ....... .... .... 114
ECON operation .. .... .... ... .... . 126
Fan . .... .... .... .... .... ... .... . 120
Heated seats , front ... .... .... .... 118
in the rear ...... .... .... .... .... . 125
Key coded setting ... .... .... .... . 114
Rear c limate controls .... .... .... . 125
Rear seat operation .. .... .... .... . 127
Rec ircu lation mode (automatic) ... .. 126
Rec ommended set tin gs ...... .... . 11 4
Residual heat .. ...... .... .. . .... . 117
Set ting t he tempe rature ..... . .... . 117
SETUP . ......... .... .... ... .... . 126
Solar blower fan/solar roof .. ...... . 123
Solar operation ... ....... .... .... 127
Switching on and off .. .... ...... .. 117
Synchroni zation .. .... .... ... .... . 127
Using climate contro l economical ly . 123
Windshield defogger/defroster . .... 123
Clock . ...... .... .... .... ... .... .... . 13
Closing Power sunroo f .... .... ... .... .... . 66
Coat hooks . ... .... .... .... .... .... . 112
Co ld ti re inflati on pressure .. ...... ... 328
Controls and equip
ment Safety first
Compartments in the door trim panels
. 111
Co mpar tmen ts in the rea r do ors ... .. .. 111
Consumer Information ... .... .... 207 , 380
Contacting N HTSA .. .. .. .... .... .... 207
Conven ie nce open featu re
Win dows ..... ... .... .... .... .... . 64
Convertib le chi ld safe ty seat .... .... .. 249
How do I properly ins ta ll a convertib le
child safety seat in my vehic le? . ... 249
Safety instructions . .... .... ....... 249
Convertible lock ing retractor
Act ivating .. ...... .... .... .... ... 255
Dea ctivati ng .. ... ... .... .... .... . 256
Using to secure a chi ld safety seat . 253,
255
Coo lant
See Engine coo lant
Cr uise control
3 14
Cha nging speed ...... .... .... .... 138
Presett ing your speed ... .. .... .... 138
Switching off .... .... .... .... .... 138
Switching on . .... .... .... ....... 137
Warning/indicator lights .. .... .... .. 21
See also Adaptive Cruis e Con trol .. .. 139
Cr uis ing ra nge . ...... .... .... .... ... . 38
Cupholder .. .. .. ...... ....... .... .. 105
Center conso le .. .. .... ..... .. .... 108
D
Damping
See Adaptive Air Suspension .. ..... 185
Data .... .... .... ... .... .... .... .... 378 Data recorder
....... .... ....... .... . 268
Date d isplay ...... .... ... .... .... .... 1 3
Daytime running lights ... .... .... .. 69, 70
def What does this mean when it appears in the trip odomete r disp lay? ... .. .... 14
Defective light bu lb warning .... .... ... 26
Defrosting/defogg ing the windows . ... 120
Defrosting/defogging windows .. ..... . 122
Determining correct load limit .... .... . 33 4
Digita l clock .. ...... .... .... .... .. . .. 13
Digita l speedometer . .... .... .... ... .. 25
Dimensions ...... .... ... .... .... ... 376
Dipstick Readi ng the dipstick proper ly .. ... . 311
Distance control system
See Adaptive Cruise Contro l ... .. ... 139
Doors Mechanica l chi ld safety lock .. ...... . 58
Power child safety lock . .... .... .... 58
P ower side door closer . ... .... .... . 53
Dr iver
See Seating posi tion ...... .... .... 200
Driver information display Driver information messages ... ... .. 29
Introduct ion .. ... .... .... .... .... . 24
Open door o r rear lid wa rn ing .. .... . 26
Outs ide temperature display .. ...... 25
Sound system disp lay ........ ... .. . 25
Driver Information System Digita l speedometer ... ... .... .... . 25
Driver 's seat .. .... .... ... .... .... .... 87
Vehicle operation Vehicle care Do-it-yourself service Technical data
Page 396 of 404

lll'ft __ A_l-=- p _h_ a_ b_e _t_ic _ a_l _in _ d_e _x ____________________________________________ _
p
Paint
Touch-up 292
Paint No. . . . . . . . . . . . . . . . . . . . . . . . . . . 374
Parking . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Automatic transmission ... .... .... 163
Caution when parking near a parking bar -
rier or curb .. .... ....... .... ... 135
Low bumper cover, spoilers and suspension . . . . . . . . . . . . . . . . . . . . 135
Parking brake
See Electromechanica l parking brake 134
P arking on a dec line (downhill) ....... 135
Parking on an incline (uphill) ... .. .... 135
Parts replacement . . . . . . . . . . . . . . . . . . 382
PASSENGER AIR BAG OFF ligh t ........ 230
Passenger's seat . . . . . . . . . . . . . . . . . . . . . 87
Passenger's seat memory . . . . . . . . . . . . . 95
Passive safety system . . . . . . . . . . . . . . . 198
Pedals ............................ 204
Physical principles of a frontal collision 210
Pockets . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Polishing .... ..... .. .... .... ...... . 291
Power locking switch . . . . . . . . . . . . . . . . . 53
Power locking system . . . . . . . . . . . . . . . . 49
Conven ience open feature .......... 64
Locking and unlocking the vehicle from
inside ........... ....... .... .... 53
Opening and closing the windows .. . 64
Rear lid/trunk lid ...... .... .... .... 55
Remote control . . . . . . . . . . . . . . . . . . . 48
Selective unlock feature . . . . . . . . . . . . 52 Settings
. . . . . . . . . . . . . . . . . . . . . . . . . 52
Unlocking and locking vehicle ... .... 51
Power roof . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Power seat Contro ls .. .... ... .... .... .... .... 87
Massage function ....... ...... .... 89
Seat adjustment ........ ....... ... 88
Upper thigh support .. ...... .... ... 88
Power side door closer . . . . . . . . . . . . . . . 53
Power steering ..................... 273
Power sunroo f
Emergency c losing ............. 67, 68
Power window switche·s ... .... ....... 62
In the driver's door ................ 63
In the front passenger's door . . . . . . . 64
Reactivating the system ............ 65
Power windows Settings . . . . . . . . . . . . . . . . . . . . . . . . . 65
Pregnant women Specia l considerations when wearing a
safety belt ..................... 215
Programming the Homelink® universal re-
mote control . . . . . . . . . . . . . . . . . . . 191
Prop er occupant seating positions .... 200
Proper safety be lt position .. .... ... .. 214
Proper seating position Front passenger ................. 201
Occupants ...................... 200
Rear passengers 202
a
Quartz clock . . . . . . . . . . . . . . . . . . . . . . . . . 13 quattro®
See All Wheel Drive
............... 273
Question
R
What happens to unbelted occupants? . .
211
Why safety belts? ................ 209
Radiator fan ........................ 317
Rain sensor ......................... 80
Rain sensor defective ... .. .... .... .... 36
Reading lights
Front . .... .... .... .... ....... .... 74
Rear ............................. 75
Rear ashtray ....................... 107
Rear center console ...... .... .... ... 108
Rear c limate controls ................ 125
Air distribution .... ....... .... ... 125
Automatic operation . ...... .... ... 125
Contro ls . ...... ..... .. .... .... .. 125
Heated seats . . . . . . . . . . . . . . . . . . . . 125
PASSIVE . ... .. .... .... ...... .... 125
Switching on and off . ...... .... ... 125
Temperature ...... .... .... .... .. 125
Ventilated seats .................. 125
Rear fog lights .. ...... .... ...... .... . 71
Rear lid
Automatic operation ............... 56
Escape handle .... .... .... .... ... 348
Opening and clos ing ... .... .... .... 55
Opening manual ly ...... .... .... ... 56