engine AUDI TT COUPE 2017 User Guide

Instruments and indicator lights
'1=1";.. Engine oil sensor
• Oil level sy stem : malfunction! Plea se con­
tact S ervic e
The senso r to check the engine oil level has
fa iled. Drive to an au thorized Aud i dea le r or a u­
thor ized Audi Se rvice Facil ity immediate ly to have
the ma lfun ction co rrected.
II O il l ev el sen sor : oil chang e nece ssar y. Plea se
con tact Service
The engine oil leve l is too high.
Drive to an a uthorized Audi dea ler or authorized
Aud i Serv ice Facility immediately to have the
malfunct ion corrected.
CJ) Note
Refer to the description in the Owner's Man­
ual ¢
page 248, Checking the engine oil level
and adding engine oil.
Bl Tank system
00] Pl ea se refuel
If the indicator lig ht turns on for the first time
and the message appears, there are about 1.9
ga l (7 L) of fue l left in the tank.
D Plea se refuel immediately
If the ind icator lig ht turns on the message ap­
pea rs, the fue l tank is almos t empty. Refuel the
veh icle immed iate ly.
D Tan k system : ma lfun ction! Plea se contact
Servic e
If the indicator light turns on and th is message
appears, there is a malfunction in the tank sys­
tem.
Drive to an authorized Aud i dealer or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
@ For the sake of the environment
Fuel should never enter the sewer system or
come into contact w ith the ground.
16
(D Tips
More information on refueling is available on
page ¢
page 241 .
~ Washer fluid level
m Please add washe r fluid
Fill the washer fluid for the windshie ld washer
system and the headlight washer system* when
the ignit ion is switched off¢
page 253.
@wind shield wipers: malfunction! P lease
conta ct Se rvice
There is a ma lfunction with the windsh ield wip­
ers .
Drive to an authorized A udi dealer or authorized
Audi Service Facility immediate ly to have the
malfunction corrected .
. ·: If the II ind icator light turns on, a bulb has
failed. The message indicates the location of the
bulb .
Replace the bulb immediately.
Vehicle light s: malfunction! Please contact
Ser vice
There is a m alfu nction in the headlights or the
li gh t sw itch. Dr ive to an a uthor ized Audi dealer or
a uth orized Aud i Serv ice Facili ty immedia tely to
have the malfunction cor rected.
_& WARNING
- Light bulbs a re under p ressure and can ex­
plode when b ulbs are replaced, wh ic h in­
creases the risk of injury .
- With gas -discharge lamps* (xenon head­
lights), the high-vo ltage component must
be handled appropriately. Otherw ise, there
is a risk of fatal injury .

co
co
.... N
" N .... 0
0
Vl c:o
~(D Headlight range control system
Iii Headlight range control : malfun ction! See
owner' s manual
There is a malfunction in the headlight range
control system, which may ca use g lare fo r othe r
d rivers.
Drive to an aut horized Aud i dea le r o r a uthorize d
Aud i Service Facility immediately to have t he
malfunct ion corrected .
§0 Audi adaptive light
Appl ies to: ve hicles with Audi adaptive light
l;J Audi adaptive light: malfunction! See own­
er's manual
There is a malfunc tion in the adapt ive lig hts . T he
h eadligh ts still f unction.
Drive to an authorized Aud i dea ler or authorized
Aud i Service Fac ility immediately to have t he
mal funct ion corrected .
~ Light/rain sensor
El Automatic headlights: malfunction! See
owner 's manual
El Automatic wipers: malfunction! See owner's
manual
The light/rain sensor is malfunct io ni ng .
The low beams remain switched on at all times
for safety reasons when the light switch is in the
AUTO position. You can continue to tur n the
lights on and off using the light switch. You can
still cont rol a ll w iper functions that are inde ­
pendent of the ra in sensor .
Drive to an authori zed Aud i dea le r or a uthori zed
Aud i Service Facility immediately to have the
malfunct ion corrected .
; Adaptive dampers
A ppl ies to: ve hicles w ith Audi drive select
B Suspension : malfunction! You may continue
driving
There is an adaptive damper malf unct ion.
Instruments and ind icator lights
D rive to an au thori zed A udi dealer or au tho rized
Audi Se rvice Facility immed iate ly to have the
malfunction corrected.
¢i ¢ Turn signals
If the . or 1B indicator light blinks, a turn sig­
nal is turned on . If both indicato r lights a re blink­
i ng, the emergency flashers are on .
On-Board Diagnostic
system (OBD)
Malfunction indicator lamp (MIL)
The malf u nction ind icator lamp ( MIL) ¢4 in t he
i ns trument cluste r is pa rt of the On Board D iag­
nost ic System (OB D II).
The wa rning/indicator lig ht tu rns on when the ig­
nition is switched on and turns off once the en­
gine is started a nd is r unning in idle at a s table
spe ed . T his ind icates t hat the MIL is f unct io ni ng
c or rectly.
If the lig ht does not turn off after start ing the
engine or t urns o n while drivi ng, this may ind i­
cate there is a malfunction in the eng ine . If the
i ndica to r tur ns o n, the cata lytic conve rter m ay be
d am aged .
Drive
with reduced engine performance (avo id
high speeds for extended per iods of t ime and/o r
fast accele rat ion) and have the ma lfu nction cor­
rec ted . See an aut hor ized A udi de aler or au thor­
i z ed Audi Service F acili ty.
T he in dicator may turn on if the e lectro nic speed
li mi ter is faulty. For ad dit io nal informa tio n, see
~ page 70, Ele ct ronic speed limite r.
17

Instrumen ts and ind icator ligh ts
On-Board Diagnostics
F ig. 4 Loc ation of D ata Link Connector (OLC)
On-Board Diagnostics monitors the components
of your emission control system. Eac h monitored
component in your engine system has been as­
signed a code . In case of a ma lfunction, the com­
ponent w ill be identified and the fa ult stored as a
code in the control module memory.
The MIL light may also ill uminate if there is a
leak in the on-board fuel vapor recovery system .
18
In order to make an accurate diagnosis, the stor­
ed data can only b e display ed using special diag­
nostic equipment (gener ic scan tool for OBD) .
In order to connect the special d iagnost ic equip­
ment, push the plug into the Data Link Connector
(DLC). The DLC is located to the right of the hood
release
~ fig. 4.
Your a utho rized Aud i dea ler or a qua lified service
station can interpret the code and perform the
necessary repair.
A WARNING
Do not use t he diagnostic connector for per­
sonal use. Incorrect usage can cause malfunc­
tions, which can increase the risk of a co lli­
sion!
-

Drive r inf orm ati on sy stem
- If your vehicle is stationary or if you are driv­
ing at very low speeds, the temperature dis­
played may be s light ly higher than the ac­
tual temperature outside due to the heat
radiating from the engine.
- At temperatures below 41 °F (+S
0
(), a
snowflake symbol appears in front of the
temperature display¢,&.
Multifunction steering
wheel plus
Operating
A pp les to: ve hicles w ith multifunctio n steering wheel p lus
The Multifunction steering wheel plus* hos 14
buttons. You con use them to operate the driver
information system and the MMI functions ,
change the volume and switch the voice recogni­
tion system* on and off.
Fig . 7 Infotainment system display
Fig . 8 Mult ifunc tion steering whee l, left side
Req uirement: the ignition must be switched on.
The driver information system contains mult iple
tabs
(D that display various informat ion @.
The follow ing tabs are available, depending on
veh icle equipment :
20
First tab Vehicle
Second Warnings
tab
a)
Third tab Radio c::> page 150
Media c::>page 155
Fourth tab Telephone*¢ page 114
Fifth tab Navigation
* c::> page 135
Map* c::> page 143
Sixth tab b) Sound¢ page 17 4
Audi connect*¢ page 126
Settings c::> page 174
a) This tab is only visible if at le ast one indicat or light or
message is shown or
if t h e correspond ing system is
switched on.
b) The contents of the tab de pend on the menu that was
used last.
@ Button ~
-Swit ch ing tab s: p ress the l<1 1>I bu tto n to the
left/right (for example, radio).
@ !VIEWI button
S witching th e view : press the !VIEWI button to
switch from the classic v iew
c::> page 19, fig. 5 to
the e nhanced view
c::>page 19, fig. 6.
@button ~
Returning to funct ions at higher levels
@ 121 and 19 contr ol butt ons
Opening/closing the selection menu or options
menu
c::> page 21.
(J) Left thumbwheel
-Sele cting a function in a m enu /list : turn the
left thumbwheel to the des ired function in a
menu or list (such as se lecting a station, Lap
times*) .
-Co nfirming a selection : press the left thumb­
wheel (for example, confirm the station).
-Zoomin g in /out on th e map : when a map is
disp layed, turn the le ft thumbwheel up/down
to zoom in/o ut on the map.

CD
CD
.... N
" N .... 0
0
Ill co
Tachometer
The tachometer displays the engine speed in rev­
olutions per minute (RPM) .
The beginning of the red zone in the tachometer
indicates the maximum permissible engine speed
for all gears once the engine has been broken in
and when it is warm. Before reaching the red
zone, you should shift into the next higher gear,
choose the Dor S selector lever position, or re­
move your foot from the accelerator pedal.
@ Note
The needle in the tachometer may only be in
the red area of the gauge for a short per iod of
time or there is a risk of damaging the engine .
The location where the red zone begins varies
depending on the engine.
@) For the sake of the environment
Upshifting early helps you to save fuel and re­
duce operating noise.
Odometer
Fig. 12 Instrument cluste r: odomete r and reset button
Trip odometer and odometer
The trip odometer shows the distance driven
since it was last reset . It can be used to measure
short distances .
The trip odometer can be reset to zero by press­ ing the reset button 10.01
r=> fig. 12.
The odometer shows the total d istance that the
veh icle has been driven.
Driver in forma tion system
Malfunction indicator
If there is a malfunction in the instrument clus­
ter,
DEF will appear in the trip odometer disp lay.
Have the malfunction corrected as soon as possi ­
ble.
On-board computer
You can access the following information in the
on-board computer
r=> page 19, fig . 5 @ .
-Time and date ~page 174
-Average consumption
-Range
- Short-term memory overv iew
- Long-term memory overview
The short -term memory collects driving informa­
tion from the time the ignition is switched on un ­
til it is switched off. If you continue driving with·
in two hours after switching the ignition off, the
new values are included when calculating the cur­
rent trip information .
Unlike the short-term memory, the long-term
memory is not erased automatically. You can se­
lect the time period for evaluating trip informa­
tion yourself .
Fuel consumption
The current fuel consumption can be shown us­
ing a bar graph . The average consumption stored
in the short-term memory is also displayed. If
the bar is green, your vehicle is saving fuel
through one of the following functions:
- Recuperation : electrical energy can be stored in
the vehicle battery when the vehicle is coasting or driving downhill. The bar will move toward
CJ .
(D Tips
The date, time of day and time and date for­
mat can be set in the Infotainment system.
23

Driver information system
Sport view
Applies to: ve hicles w ith boost p ressure indicato r and engine o il tempera ture indica tor (S models)
Fig. 13 Drive r informatio n system d iag ram: sport v iew
Always set the desired driver information system
view before driving, because display functions
will not be available for several seconds.
• Select in the Infotainment system:
IMENU I but­
ton
> Vehicle > left contro l button > Layout
• Se lect the des ired sett ing by mov ing the cursor
(red frame).
The driver information system displays various
items.
(D Tab area
@ Tachometer including d igital tachometer and
odometer displays
@ Additional display (divided in two sections in
the enhanced view)
© Boost pressure indicator
® Engine oil temperature ind icator
@ Status line
(f) Funct ion sect ion (centra l area shifted to the
l eft)
Boost pressure indicator (Boost)
A bar graph that begins on the left and fills in to­
ward the right indicates the engine's curre nt load
(meaning the current boost pressure).
Engine oil temperature indicator
The display ---°F appears in the instrument clus ­
ter when the engine oil temperature is below
140 °F (60 °().
24
The eng ine has reached its operating tempera­
ture when the engi ne oil temperatu re is between
176 °F (80 °() and 248 °F (120 °C) under normal
driv ing cond itions. The eng ine o il temperature
may be higher if there is heavy engine load and
high temperatures outside. This is not a cause for
concern as long as the
. c> page 12 or
Ill e> page 15 indicator light is not flashing in the
display .
@ Tips
-You can select the units used for tempera­
ture, speed and other measurements in the
Infota inment system.
- If your vehicle is stationary or if you are driv­
ing at very low speeds, the temperature dis­
played may be slightly higher than the ac­
tual temperature outside due to the heat ra­
diating from the engine.
- At temperatures below41 °F (+5 °(), a
snowflake symbol appears in front of the
tempe rature disp lay
c> .& in Overview on
page 19.

Opening and clo sin g
@ Key tag with PIN
Only app lies to veh icles with Connec tiv ity serv­
ice*: open the key fob and rub th e PIN unti l it is
visib le. You can activate the Connectivity service*
on your vehicl e using this PIN code.
Replacing a key
If a key is lost, see an authorized Audi dealer or
author ized Audi Service Facility. Have
this key de­
activated . It is important to bri ng a ll keys with
you . If a key is lost, you should report it to your
insuranc e company.
Numb er of keys
You can check the n umber of keys ass igned to
your veh icle in the Infotainment system . To do
this, select : the
I MEN U I button > Vehicl e > left
control b utton
> Service & chec ks > Vehicle in­
fo rm ation .
This way, you can make sure that you
have all the keys when purchasing a used vehicle .
Electron ic immobili ze r
The immobilizer preven ts unauthorized use of
the vehicle .
Under ce rtain c ircumstances, the ve hicle may not
be ab le to start if the re is a key from a differe nt
vehicle manufact urer on the key chain .
Data in the master k ey
When driving, service and maintenance-relevant
data is continuously stored in your remote con­
trol key. Your Aud i service adv isor can read out
this da ta and tell yo u about the wo rk your vehicle
needs . This applies a lso to vehicles with a con ­
ven ience key* .
Personal convenience settings
If two peop le use one vehicle, it is recommended
that ea ch pe rson always uses "t heir ow n" master
key. When the ignition is tur ned off or when the
vehicle is locked, persona l convenience settings
for the follow ing systems are stored and as­
signed to the remote mast er key.
- Clima te contro l system
- Parking a id*
- Active lane assist*
- Side assist*
26
- Drive se lect
The stored settings a re a utomat ica lly recalled
whe n you unlock the vehicle , open the doo rs or
tu rn o n the ignition.
&_ WARNING
Always take the vehicle key with you when
leav ing the veh icle, even for a short period of
time. This applies particularly when chi ldren
remain in the vehicle . Otherwise the children
could start the engine or operate e lectrica l
equ ipment such as power wi ndows.
(D Tips
-
The operation of the remote control key can
be temporarily d isrupted by interference from
transmitters near the vehicle working in the
same frequency range (such as a cell phone or radio equipment) . A lways check if your vehicle
i s locked!
Removing the mechanical key
F ig. 15 Remote control m aste r key : remov ing the mec hani ­
ca l key
.. Press the re lease buttons (!)¢ fig. 15 and re ­
move the mecha nica l key from the remote con ­
trol key .
Using the mec hani cal key, yo u ca n:
- Lock/unlock the g love compar tment .
- Ma nually lock/unlock the vehicle¢
page 30.
-Emergency lock the doors¢ page 30.

Opening and closing
& WARNING
No one, especially children, should stay in the
vehicle when it is locked from the outside, be ­
cause the w indows can no longer be opened
from the inside¢
page 30. Locked doors
make it more difficu lt for eme rgency workers
to get into the vehicle, which puts lives at
risk.
@ Tips
- Only use the remote control key when you
a re within view of the vehicle.
- Do not use the remote control when you are
in side the vehicle. Otherwise, you could un­
in tent ionally lock the vehicle. If you then
tried to start the engine or open a door, the
alarm would be triggered. If this happens,
press the un lock button@.
- The selector lever must be in the P position
on vehicles with a convenience key*. Other­
wise the vehicle will not be ab le to lock .
- Only use the panic function in an emergen ­
cy.
Unlocking and locking with the
convenience key
App lies to: ve hicles with conven ience key
The doors and luggage compartment lid can be
unlocked/locked without using the remote con­
trol key .
Fig. 19 Door han dle : senso r
Unlocking the vehicle
.,. Grip the door handle . The door unlocks auto­
matically.
.,. Pull on the door handle to open the door.
28
.... 0 0
0
~ al
Locking the vehicle
.,. Place the selector lever in the P position (auto­
matic transmissions), or else the vehicle wi ll
not be able to lock.
.,. To lock the vehicle, close the door and touch
the sensor in the door handle once¢
fig. 19. Do
not hold the door handle while doing this .
You can unlock/lock the vehicle at every door.
The remote control key cannot be more than ap­
prox imately S ft (1.5 m) away from the door han­
dle. It makes no difference whether the master
key is in your jacket pocket or in your briefcase,
for example .
If you hold the door handle while locking, this
can impair the locking function.
The door cannot be opened for a brief period di­
rectly after locking it. This way you have the op­
portunity to check if the doors locked correctly.
The settings in the Infotainment system deter­
mine if the entire vehicle or on ly one of the doors
is un locked when un locking the vehicle
¢ page 29.
& WARNING
Read and follow ing all WARNINGS. ¢ A in
Key set on page 26
{!) Tips
If your vehicle is left standing for a long peri­
od of t ime, note the following :
- The proximity sensor sw itches off after a
few days to
save energy. You then have to
pull once on the door handle to un lock the
vehicle and a second time to open it.
- The energy management system gradually
turns off unnecessary convenience functions
to prevent the veh icle battery from drain ing
and to maintain the vehicle's ability to start
for as lon g as poss ible. You may not be ab le
to unlock your vehicle using the convenience
key.
- For an explanati on on conformity with the
FCC reg ulations in the United States and the
Industry Canada regulations, see
¢page 304.
-

Warm and cold
Automatic climate control system controls
Fig. 56 Automatic climate co ntrol syste m: controls
You can control the functions through the dial,
buttons in the dial and the buttons . Press the
buttons to turn the functions on or off . The LED
i n a button w ill light up when the funct ion is
sw itched on .
We recommend pressing the
IAU TOI button and
setting the temperature to 72 °F (22 °C) . The au­
tomatic climate control system automatically
maintains a temperature once it has been set .
The air temperature coming from the vents, the
b lower speed, and the air dis tribution are also
automatically adjuste d. In all heati ng mode func ­
tions except
defrost, the blower only switches to
a higher speed once the engine coolant has
reached a certain temperat ure.
~ Adjusting the blower
The blower speed can be adjusted in small incre­
ments using the dial @. The blower should al­
ways run at a low setting to prevent the windows
from fogging and to ensure a continuous ex­
change of air inside the vehicle. You can adjust
the volume of a ir generated by the blower to your
preference . To have the blower regulated auto­
mat ically, press the
IAUTOI butto n.
IA/C l Switching cooling mode on and off
The cooling system is turned on and off w ith the
IA/C l button. The air is not cooled and humidity is
not removed when cooling mode is switched off.
52
This can cause fog on the w indows. Coo ling mode
switches off automatically when the outside tem­
perature is below zero .
The temperature can be adjusted with the con ­
trol @.
I• I • I Adjusting the tempe rature
The temperature can be adjusted in small incre­
ments using the dial@.
I AUTO I Switching automatic mode on and off
The au tomatic mode is turned on using the
IAUTOI button. AUTO mode switches off once a
button in the climate control system is pressed.
Automat ic mode maintains a constant tempera­
ture inside the vehicle . Air temperature , airflow
and air distribution are controlled automatically.
Adjusting the air distribution
The air distribution can be adjusted with the con­
tro l@ . To have the air distribution regulated au­
tomatica lly, press the
IAUTO l button.
The round ai r vents in the cockpit a re adjustable
¢ page 53.
To keep the front side windows from fogg ing up
i n damp weather, we recommend ope ning the
s ide air vents and tilting them to the side.

CD
CD
.... N
" N ...... 0
0
Ill co
1- 1 Switching recirculation mode on and off
The recirculation mode can be turned on manual­
l y or automatica lly* .
- Swi tchi ng manual recirculat ion mode on and
off: press
l '-"'> I
- Automa tic* recirculation mode: auto rec ircula­
t ion needs to be activa ted in the Infotainmen t
system. Selec t in the Infota inment system :
I MENU I button >Vehicle > left control button
>Vehicle settings> Air conditioning > Auto re­
circulation .
The air quality sensor that is de­
signed for diese l and gasoline exhaust auto­
matically switches the recirculation mode on or
off depend ing on the level of pollutants in the
outside air .
In recircu lation mode, the air inside the vehicle is
circu lated and filtered . This prevents the unfil­
tered air outside the vehicle from entering the
vehicle interio r. We recommend switching recir ­
culation mode on when dr iv ing through a tunnel
or when sitting in traffic
c::> .&,.
Recirculation mode is switched off by pressing
the ~ button or
I AU TO I orl w MAX !.
I@ MAXI Switching defrost on and off
The winds hield and side windows are defrosted
or cleared of condensation as quickly as possible.
The optimum amount of a ir flows main ly out of
the vents under the windshield . Recirculation
mode switches off . The temperature is controlled
automatically .
The
IAUTOI button switches the defroster off.
I @ REAR I Switching the rear window defogger
on and off
If the rear w indow defogger is activated when
the ignition is switched on, the battery manage­
ment determines based on the battery charge if
it is possib le to turn on. Otherwise, the rear win ­
dow defogger functions with the engine running
and switches off automatically after approxi­
mately 10 -20 min utes, depending on the out­
side temperature.
To prevent t he rear w indow defogger from
switching off automatically, press and hold the
I@ REARI button for more than two seconds. This
Warm and cold
remains stored up to approximately 15 minutes
after t urning off the ignition.
.&_ WARNING
-
You should not use the recirculation mode for
an extended period since no fresh a ir is drawn
in. With the air-conditioning switched off, the
windows can fog up, which increases the risk
of an acc ident .
Adjusting the air vents
Fig. 57 Cock pit: adjust ing the a ir vents
To adjust the direction of air flow, turn the
ridged outer ad justment wheel
(D e::> fig . 57.
To adjust the amount of air flow , move the lever
@ on the a ir vent. To stop the air flow, move the
lever all the way to the left.
Seat heating
Fig. 58 Air vents: seat heat ing
The seat heating has three levels . The se lected
heat leve l is indicated by the LED.
.,. To switch the seat heating on, press the~ but­
ton once.
.,. To switch to a lower level, press the~ button
aga in.
IJl,,
53