ECU AUDI TT ROADSTER 2016 Owners Manual

Downloaded from www.Manualslib.com manuals search engine Table
of Contents
Audi smartphone interface . . . . . . 210
Setting up.......................... 210
How to use . . . . . . . . . . . . . . . . . . . . . . . . . 211
Troubleshooting..................... 211
System settings .................. 212
Setting the time and date . . . . . . . . . . . . .
212
MMI settings . . . . . . . . . . . . . . . . . . . . . . .
212
Connection manager . . . . . . . . . . . . . . . . .
213
System update . . . . . . . . . . . . . . . . . . . . . .
216
On-board Handbook.................. 216
Sound settings . . . . . . . . . . . . . . . . . . . . . .
217
Volume settings ..................... 217
Restarting the MMI system (Reset) . . . . . 218
Notes on software licences 218
Safety ............................ 220
Safe driving . . . . . . . . . . . . . . . . . . . . . . 220
General notes . . . . . . . . . . . . . . . . . . . . . . .
220
Correct sitting positions . . . . . . . . . . . . . . 221
Child seats . . . . . . . . . . . . . . . . . . . . . . . . .
223
Securing a child seat . . . . . . . . . . . . . . . . .
225
Pedal area . . . . . . . . . . . . . . . . . . . . . . . . . . 226
Stowing luggage safely . . . . . . . . . . . . . . .
227
Pedestrian protection system . . . . . . . . . . 228
Seat belts . . . . . . . . . . . . . . . . . . . . . . . .
230
Why is it so important to use seat belts? . 230
Forces acting in a collision . . . . . . . . . . . . .
231
How to wear seat belts properly . . . . . . . .
232
Belt tensioners . . . . . . . . . . . . . . . . . . . . . .
234
Airbag system . . . . . . . . . . . . . . . . . . . . 235
Description of airbag system . . . . . . . . . . .
235
Front airbags . . . . . . . . . . . . . . . . . . . . . . .
236
Side airbags . . . . . . . . . . . . . . . . . . . . . . . .
239
Service and care . . . . . . . . . . . . . . . . . . 241
Checking and topping up fluids . 241
Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Filling the tank . . . . . . . . . . . . . . . . . . . . . . 242
Emission control systems . . . . . . . . . . . . . 244
Engine compartment . . . . . . . . . . . . . . . . . 244
Engine oil . . . . . . . . . . . . . . . . . . . . . . . . . .
247
Cooling system . . . . . . . . . . . . . . . . . . . . . .
249
Brake fluid . . . . . . . . . . . . . . . . . . . . . . . . .
250
Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . .
250
4 Windscreen
washer . . . . . . . . . . . . . . . . . .
252
Service interval display . . . . . . . . . . . . . . .
252
Wheels ........................... 254
Tyres and rims . . . . . . . . . . . . . . . . . . . . . .
254
Tyre pressure loss indicator . . . . . . . . . . . . 258
Tyre pressure monitoring system . . . . . . .
260
Care of vehicle and cleaning . . . . .
263
General notes . . . . . . . . . . . . . . . . . . . . . . .
263
Washing the vehicle . . . . . . . . . . . . . . . . . .
263
Notes on cleaning and care . . . . . . . . . . . . 264
Taking the vehicle out of service . . . . . . . . 268
Self-help . . . . . . . . . . . . . . . . . . . . . . . . .
269
Mobility . . . . . . . . . . . . . . . . . . . . . . . . . . 269
General notes . . . . . . . . . . . . . . . . . . . . . . .
269
Equipment . . . . . . . . . . . . . . . . . . . . . . . . .
269
Tyre repair kit . . . . . . . . . . . . . . . . . . . . . . .
270
Changing a wheel . . . . . . . . . . . . . . . . . . . .
272
Spare wheel . . . . . . . . . . . . . . . . . . . . . . . .
276
Jump-starting . . . . . . . . . . . . . . . . . . . . . . .
277
Tow-starting / towing away. . . . . . . . . . . . 278
Fuses and bulbs . . . . . . . . . . . . . . . . . .
282
Fuses.............................. 282
Bulbs.............................. 284
Accessories and technical data . . 285
Accessories and modifications
to the vehicle . . . . . . . . . . . . . . . . . . . . . 285
Accessories, replacement parts and
repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
Modifications . . . . . . . . . . . . . . . . . . . . . . . 285
Radio transmitters and business
equipment . . . . . . . . . . . . . . . . . . . . . . . . . 286
Technical data . . . . . . . . . . . . . . . . . . . . 287
Vehicle identification
data . . . . . . . . . . . . . 287
Explanation of technical data . . . . . . . . . . 287
Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . 288
Capacities . . . . . . . . . . . . . . . . . . . . . . . . . . 288
Weights . . . . . . . . . . . . . . . . . . . . . . . . . . .
288
Engine data . . . . . . . . . . . . . . . . . . . . . . . .
289
Index ............................. 290

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) -
How do I operate the map functions?
¢page 178.
- How can I display traffic information?
¢page 182.
Entertainment
- How can I listen to the radio? ¢ page 185.
- How can I play media? ¢page 200.
- How can I play music from my mobile phone via
the infotainment system?¢ page 194, Blue­
tooth audio player.
Tips and tricks
- How can I unlock my vehicle from inside to let
passengers in?¢ page 31.
- How can I open all the windows from outside
using the remote control key?¢ page 35,
Convenience open/close function.
- How can I deactivate the passenger's airbag?
¢page 237.
- How do I secure a child seat? ¢ page 225.
- What do I have to be aware of when driving
through an automatic car wash? ¢ page 263.
- How can I drive (more) economically?
¢page 67.
- How can I see when the next service date is?
¢page 252. FAQs
7

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
....
0
,.....
Vl
CX) Trip
recorder/odometer
The trip recorder shows the distance that has
been travelled since it was last reset. It is used to
measure individual journeys.
The trip recorder can be reset to zero by pressing
the reset button lo.al ¢Fig. 12.
The odometer records the vehicle's total mileage.
Fault display
If there is a fault in the instruments, the letters
DEF appear in the trip recorder display. Have the
fault rectified as soon as possible.
On-board computer
You can call up the following information se­
quentially on the on-board computer ¢ page 20,
Fig. 4@ :
-Time & date ¢page 212
-Average consumption
- Fuel range
- Single journey memory summary
- Total journey memory summary
The single journey memory processes the infor­
mation on a journey from the time the ignition is
Sport view Driver
information system
switched on until it is switched off. If the journey
is resumed within two hours after the ignition is
switched off, the new figures are automatically
included in the calculation.
Unlike the single journey memory, the total jour­
ney memory is not erased automatically. In this
way, you can determine the period for which you
wish the on-board computer to supply driving in­
formation.
Fuel consumption
The current fuel consumption can be shown in a
bar display. The average fuel consumption from
the single journey memory can also be displayed.
If the bar turns green, your vehicle is saving fuel
using one of the following functions:
- Recuperation: Electrical energy can be stored in
the vehicle battery (recuperation) if the vehicle
is travelling downhill or coasting in gear (over­
run). In this case, the bar will move towards the
t:::3 symbol.
- Coasting mode* ¢ page 82.
@ Note
The date, time and display format can be
changed via the infotainment system.
Applies to: vehicles with boost pressure display and engine oil temperature display
Fig. 13 Driver information system: Sport view
Always select the desired view in the driver infor­
mation system before starting a journey, because the
display functions will not be available for a
few seconds.
25

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
....
0
,.....
Vl
CX) as
the windows cannot be opened from the
inside in an emergency.
(©) Note
- The windows can be operated for about ten
minutes after the ignition has been switch­
ed off. The window switches are only deacti­
vated when the driver's door or the passeng­
er's door is opened.
- When the doors are opened, or while the
soft top is being opened or closed, the win­
dows are automatically opened about
10mm.
Convenience open/close function
All the windows can be opened or closed at the
same time.
Convenience open function
"" Press and hold the� button on the remote
control key until all the windows have reached
the desired position.
Convenience close function
"" Press and hold the� button on the remote con-
trol key until all windows are closed ¢ ,& , or
Convenience close function with convenience
key*
"" Touch and keep your hand in contact with the
sensor* on the door handle until all the win­
dows and the soft top* are closed. Do not rest
your hand on the door handle while this is hap­
pening.
Adjusting settings for convenience open
function via infotainment system
"" Select the following on the infotainment sys­
tem: I MENU
I button
>Car> left control button
> Vehicle settings.
If you wish to use the convenience open function
for the windows, set Long press to open win­
dows to on. Doors
and windows
A WARNING
- Take care when closing the windows and the
soft top*. Careless or uncontrolled use can
cause injuries.
- For safety reasons, you should only use the
remote control key to open and close the
windows and soft top* when you are at least
2 metres away from the vehicle. To avoid in­
juries, always keep an eye on the windows
and the soft top* when pressing the I:@ but­
ton to close them. The windows and soft top
stop moving as soon as the I:@ button is re­
leased.
What to do after a malfunction
You can reactivate the one-touch open and close
function if it fails to operate.
"" Pull and hold the electric window switch until
the window is fully closed.
"" Release the switch and then pull it again for at
least one second.
Garage door opener
(Homelink)
Description
Applies to: vehicles with garage door opener (Homelink)
Fig. 27 Garage door opener: Examples of various devices
which can be activated
The garage door opener (Homelink) allows you
to activate garage doors, security systems, home
or office lighting and other electric devices by
means of control buttons inside your car. It com­
prises three buttons, integrated in the operating
unit above the interior mirror in the headliner, �
35

Downloaded from www.Manualslib.com manuals search engine Doors
and windows
which perform the functions of up to three hand­
held transmitters.
To operate the desired systems with the garage
door opener, you first need to program the but­
tons in the operating unit.
A WARNING
When you are operating or programming the
garage door opener, make sure that no per­
sons or objects are close to the devices receiv­
ing the transmitter signals. Otherwise, per­
sons might be injured or other damage
caused by moving parts.
(D Note
- For security reasons we recommend that
you delete the programming of the buttons
prior to selling your vehicle.
- For more information about Homelink,
please see www.homelink.com.
Controls
Applies to: vehicles with garage door opener (Homelink)
Fig. 28 Operating unit above the interior mirror
Important: The button in the operating unit must
be programmed <=> page 36 and the vehicle
must be within range of the garage door or other
system you wish to operate.
.. To open the garage door, press the button. The
green LED CD will light up or flash.
.. To close the garage door, press the button
again.
Note
When opening/closing the garage door, do
not keep the button pressed for more than
36 20
seconds; otherwise the garage door open­
er will switch to the programming mode.
Programming the transmitter
Applies to: vehicles with garage door opener (Homelink)
Fig. 29 Distance between radiator grille and hand-held
transmitter
Programming a button: Stage 1 (at the
operating unit)
1. Switch on the ignition.
2. Press
and hold down the two outer buttons
on the operating unit<=> page 36, Fig. 28 until
the yellow LED@ goes out and the green
LED CD flashes. This procedure will delete the
standard factory settings and does not need
to be repeated when programming the other
buttons.
3. Briefly
press the particular button in the op­
erating unit that you would like to program.
4. Wait until the yellow LED@flashes . The
programming mode is then activated for 5
minutes.
5. Step in front of your vehicle with the original
hand-held transmitter for the system you
wish to assign to the button in the operating
unit.
Programming a button: Stage 2 (at the
radiator grille)
6. Hold
the hand-held transmitter in front of
your car's radiator grille<=> Fig. 29.
7. Now press and hold the button on the hand­
held transmitter until the turn signals on
your vehicle start to flash. This can take up to
30 seconds.
8. If the hazard lights flash three times, the
button has been programmed successfully. If
the hazard lights flash once only, the
�

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) programming
operation has failed or the five
minute programming period has expired. Re­
peat the programming procedure starting
with the 3rd step, or try holding the trans­
mitter nearer or further away from the radia­
tor grille.
9. If the garage door or other system still fails
to be activated using the buttons in the oper­
ating unit after programming is completed,
it is possible that the system might be work­
ing with a rolling code instead of the normal
fixed security code. If this is the case, a roll­
ing code progr amming is required in addi­
tion to the steps described above
¢page 37.
Follow the instructions above to program the
other two buttons. Start with the 3rd step.
Erasing the button programming
Programmed buttons can only be erased all at
once; it is not possible to erase them individually.
Reprogram the buttons if necessary.
� Switch on the ignition.
� Press and hold down the two outer buttons on
the operating unit until the yellow LED @
goes
out and the green LED CD
flashes.
Reprogramming the buttons
� Switch on the ignition.
� To reprogram an individual button, press and
hold the desired button until the green LED CD
goes out and the yellow LED @
starts to flash
(after about 20 seconds). Then release the but­
ton immediately. The programming mode is
then activated for S minutes.
� Continue with the 5th step.
ij) Note
- The required distance between the hand­
held transmitter and the Homelink module
inside the radiator grille¢ Fig. 29 depends
on the system you are programming.
- With some types of systems, you may need
to briefly release the button during pro­
gramming and then press it again. When
programming a new device, keep the button
pressed for at least 15 seconds before try- Doors
and windows
ing again with the transmitter in a different
position. Watch out for your vehicle's haz­
ard warning lights while doing so.
Rolling code programming
Applies to: vehicles with garage door opener (Homelink)
Some devices require rolling code programming.
Identifying a rolling code
� Press a programmed button in the operating
unit again and hold it down.
� Watch the green LED CD
¢ page 36, Fig. 28. If
the green LED starts flashing rapidly, this indi­
cates that the system you wish to operate, such
as a garage door, is equipped with a rolling
code.
� Program the rolling code as follows:
Activating a system's drive unit
� Locate
the programming button on the sys­
tem's drive unit. The exact location and colour
of the button may vary depending on the type
of system.
� Press
the programming button on the system's
drive unit (this will normally cause an indicator
lamp on the unit to light up). You now have
about 30 seconds to start and complete pro­
gramming of the button in the operating unit.
Programming the button in the operating
unit
� Press the previously programmed button in the
operating unit for 2 seconds.
� Press the button for 2 seconds again to com­
plete rolling code programming.
� For some systems, the button may have to be
pressed a third time to complete the program­
ming sequence.
After programming, the system should recognise
the signal and respond when the button in the
operating unit is pressed. Now the other control
buttons can be programmed as required.
@ Note
- Having a second person assist you makes
programming of the rolling code easier and
faster. ..,_
37

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
....
0
,.....
Vl
CX) Soft
top: not secure. Speed too high
This message will appear if you exceed a speed of
SO km/h while the soft top is opening or closing.
Reduce speed and open or close the soft top
again.
Soft top: fault. You can continue driving
(limited functionality). See owner's manual
This message will appear if a system malfunction
occurs. Try to open or close the soft top again. If
the message still appears, drive to a qualified
workshop (but do not exceed SO km/h) and have
the fault rectified.
,8. WARNING
Never drive with the soft top not correctly
Locked in place. There is a danger that the
fabric could be caught by the airstream and
blown open. This could cause an accident,
possibly resulting in personal injury or dam­
age to the car.
Windbreak
Applies to: vehicles with windbreak
The windbreak reduces draughts inside the vehi­
cle for greater comfort when driving with the
soft top open.
Fig. 32 Centre console: Control switch for windbreak
The windbreak can be raised and Lowered electri­
cally.
""To extend the windbreak, pull and hold the
windbreak control switch until the windbreak is
fully extended.
""To Lower the windbreak, press and hold the
control switch for the windbreak until the wind­
break is fully retracted . Soft
top (folding roof)
,8. WARNING
-
- Never use the windbreak to secure Loads.
- Take care when closing the windbreak. Care-
less use of the windbreak can cause severe
injuries.
{(D) Note
- The windbreak will stop moving immediate­
ly in any position if the switch is released.
- The windbreak is most effective if the win­
dows are fully raised when driving.
Manual operation of the
soft top
General notes
The soft top can be closed manually in the event
of a malfunction.
""Apply the parking brake.
"" Open all the windows.
"" Switch off the ignition.
You should only operate the soft top manually if
you need to close it and the power-operated sys­
tem does not work. It is advisable to have a sec­
ond person help you. Drive to a qualified work­
shop soon and have the fault rectified.
,8. WARNING
- In all the steps required for manual opera­
tion of the soft top, there is always a risk of
catching your hands or causing injury tooth­
ers.
- Please ensure that all windows are down
before operating the soft top manually.
- Keep well clear of the frame mechanism
and other moving parts.
- Never drive with the soft top not correctly
Locked in place. There is a danger that the
fabric could be caught by the airstream and
blown open. This could cause an accident,
possibly resulting in personal injury or dam­
age to the car.
41

Downloaded from www.Manualslib.com manuals search engine Seats
and storage
Luggage compartment
General notes
A WARNING
Please refer to the important safety notes on
¢page 227, Stowing Luggage safely.
Load-through hatch with bag
Applies to: vehicles with load-through hatch and removable
ski bag
The bag can be used to transport Long items
(such as skis).
Fig. 61 Luggage compartment: Cover
AUD!
Fig. 62 Luggage compartment: Securing the bag
Loading
� Open the flap for the storage compartment be­
tween the backrests ¢page 57.
� Open the boot lid.
� Press the release catch and fold down the cover
for the load-through hatch towards the lug­
gage compartment ¢ Fig. 61.
� Push the bag (with the zip pointing towards the
rear of the vehicle) from the luggage compart­
ment into the passenger compartment ¢.&_.
� Load up the ski bag.
58 Securing
the bag
� Hook each of the attachments on the two fas­
tening belts into the corresponding rear fasten­
ing ring ¢Fig. 62.
A WARNING
The bag must be strapped in place with the
two fastening belts after it has been loaded.
(D) Note
- Fold up the bag only when it is dry.
- Place skis in the bag with their tips facing
forwards and ski poles with their tips facing
backwards.
Lowering the luggage compartment floor
panel
The Luggage compartment floor panel can be
Lowered in certain special cases.
Fig. 64 Luggage compartment: Spare wheel removed
� Take out the floor panel ¢ page 270.
� Remove the plastic base panels ¢ Fig. 63.
� Turn the knob anti-clockwise and take out the
foam insert.
� Take out the spare wheel.

Downloaded from www.Manualslib.com manuals search engine Driving
The tyre pressures should always be checked
when the tyres are cold.
Do not use winter tyres all through the year; they
will increase fuel consumption by up to 10 %.
Avoid carrying unnecessary loads
Every kilo of extra weight will increase the fuel
consumption, so it is worth checking the luggage
compartment occasionally to make sure that no
unnecessary loads are being transported.
Save electrical energy
The engine drives the alternator to generate elec­
tricity. This means that fuel consumption rises
when more power is required for electrical equip­
ment. Switch off electrical equipment when it is
not needed. Electrical equipment which uses a
lot of electricity includes the blower (at a high
setting), the rear window heating and the seat
heating*.
Steering Adjusting the steering wheel position
The height and reach of the steering wheel can
be adjusted as required to suit the driver.
Fig. 71 Lever on steering column
� Press the lever¢ Fig. 71 down ¢ .&, .
� Move
the steering wheel to the desired posi­
tion.
� Then push the lever towards the steering col­
umn until the catch engages.
68 A
WARNING
- Never adjust the position of the steering
wheel when the vehicle is moving - this
could cause an accident.
- Press the lever upwards so it is secure and
so that the position of the steering wheel
cannot shift unexpectedly while the vehicle
is moving -risk of accident!
Starting and stopping
the engine
Starting the engine -
You can use the !START
ENGINE STOP!
button to
switch on the ignition and start the engine.
Fig. 72 Centre console: START ENGINE STOP button
Applies to TT RS
Fig. 73 Steering wheel: START ENGINE STOP
Switching the ignition on/off
� To switch the ignition on/off, press the
!START ENGINE STOP!
button without pressing
the clutch pedal (manual gearbox) or brake
pedal (automatic gearbox). Diesel engines are
preheated when the ignition is switched on.�

Downloaded from www.Manualslib.com manuals search engine 0
0
N
,.....
N
......
0
,.....
Vl
CX) Audi
connect
Introduction
Applies to: vehicles with Audi connect
Audi connect services allow online information to
be directly transmitted and integrated into the
vehicle.
Thanks to a Wi-Fi hotspot, it is possible to use a
mobile device to access the Internet when the ve­
hicle is stationary.
A WARNING
- Only use Audi connect services when the
traffic conditions allow you to do so safely -
risk of accident! Please always observe the
notes in the chapter ¢page 121, Notes on
traffic safety.
- Mobile devices, tablet and laptop computers
and devices of a similar weight can only be
operated safely when the vehicle is station­
ary. Like any loose object, they can be cata­
pulted through the vehicle in an accident
and cause serious injuries. Always make sure
that such devices are securely stowed while
you are driving.
-Audi connect services should only be used
via a Wi-Fi hotspot when the vehicle is sta­
tionary -risk of accident!
Pl ease also refer to ¢ page 167, Notes on
Audi connect before using.
Setting up
Before you start
Applies to: vehicles with Audi connect
An Internet connection is required in order to use
Audi connect. You can establish a connection by
using one of the following options:
l) Not available in all markets. Applies to mobile phones
with Bluetooth remote SIM Access Profile on vehicles with
Audi connect and Audi phone box*.
2 > Not available for all countries and models Audi
connect
Option 1
Using a separate mini SIM card in the SIM card
reader ¢ page 159
Option 21
)
Connecting an rSAP¢ page 160 enabled mobile
phone via Bluetooth
Option 32
)
Using a mobile device (e.g. a smartphone) as a
personal Wi-Fi hotspot for the MMI ¢ page 161
Using the SIM card reader
Applies to: vehicles with SIM card reader
Fig. 150 Mini SIM card (actual size)
Important
The vehicle must be stationary.
The ignition must be switched on.
Inserting a SIM card
.,.. Select: I MENU
I button > Audi connect.
159