headlight bulb BMW MOTORRAD K 1200 R 2004 Rider's Manual (in English)

Status indicators226
Battery charge current
General warning light
lights up red.
Battery charge current
symbol is displayed.
The battery is no longer being
charged. You can continue to
ride only until the battery is
discharged. A discharged battery can
result in the engine cut-
ting out unexpectedly, causing
a hazardous situation.
If possible, do not continue to
ride. c
• Have the fault rectified as soon as possible by a spe-
cialist workshop, preferably
an authorised
BMW motorcycle dealer.
Defective bulb
A defective bulb can
make it harder for you to
see or your motorcycle less
noticeable for other road
users.
Have defective bulbs replaced
as soon as possible. c
General warning light
lights up yellow.
Defective bulb symbol
with arrow pointing to the
rear is displayed.
Rear light or brake light lamp
defective.
• Replace bulbs (
b
109). Defective bulb symbol
with arrow pointing to the
front is displayed.
Low-beam headlight, high-
beam headlight, parking light
or turn indicator defective.
• Replace bulbs (
b
109).
Defective bulb symbol
with two arrows is
displayed.
A combination of the bulb
defects described above has
occurred.
• Replace bulbs (
b
109).

Maintenance6110
A defective bulb places
your safety at risk be-
cause it is easier for other road
users to oversee you and your
motorcycle.
Replace defective bulbs as
soon as possible; always carry
a complete set of spare bulbs
if possible. c
The types of bulb used
are listed on (
b
139). c
Do not touch the glass of
new bulbs with your fin-
gers. Use a clean, dry cloth to
hold the bulbs when handling
them. Dirt deposits, in particu-
lar oil and grease, interfere
with heat radiation from the
bulb. This leads to overheating
and shortens the bulb’s oper-
ating life. c The types of threaded
fastener used are listed
on (
b
128). c
Replacing low-beam
headlight bulb
If it is not standing firmly,
the motorcycle could
topple in the course of the
operations described below.
Make sure that the motorcycle
is steady on its stand. c
The bulb is pressurised
and can cause injury if
damaged.
Wear protective goggles and
gloves when changing
bulbs. c
Turn the handlebars to
the right to facilitate
access. c High-beam headlight
1 and
low-beam headlight 2 are
accessible from behind.
• Switch off the ignition.
•Turn cover 3 counter-clock-
wise and remove it.

6111
Maintenance
• Disconnect plug 4.
• Disengage spring clip 5 and
push it aside. • Remove bulb
6.
Installation is the reverse of the
removal procedure.
• When installing, make sure that lug 7 is pointing up.
Replacing high-beam
headlight bulb
If it is not standing firmly,
the motorcycle could
topple in the course of the op-
erations described below.
Make sure that the motorcycle
is steady on its stand. c
The bulb is pressurised
and can cause injury if
damaged.
Wear protective goggles and
gloves when changing
bulbs.c
Turn the handlebars to
the left to facilitate
access. c

Maintenance6112
• The procedure for changing the high-beam headlight
bulb is the same as that for
the low-beam bulb. Note,
however, that the high-beam
headlight bulb is held in
place by a single-leg, vertical
spring clip.Replacing parking light
If it is not standing firmly,
the motorcycle could
topple in the course of the
operations described below.
Make sure that the motorcycle
is steady on its stand. c• Switch off the ignition.
• Remove securing screws
1
on both sides of the bulb
housing. • Pull the bulb housing for-
ward and tilt it slightly down.
• Turn bulb holder 2 counter-
clockwise to remove it from
the headlight housing.
• Remove bulb 3 from the bulb
holder.
Installation is the reverse of the
removal procedure.
• Use a clean, dry cloth to hold the new bulb.

6113
Maintenance
• Press the bulb housing into mounts 4 on the frame and
install the securing screws.
Incorrectly routed head-
light cables could catch
on the steering.
Use suitable retainers to se-
cure the cables to the rear of
the headlight. c
Replacing brake light and
rear light bulbs
If it is not standing firmly,
the motorcycle could
topple in the course of the op-
erations described below.
Make sure that the motorcycle
is steady on its stand. c
• Switch off the ignition.
• Remove the seat (
b
44).
• Remove screw 1. • Pull the bulb housing to the
rear until it is clear of
holders 2.
• Turn bulb holder 3 counter-
clockwise to remove it from
the bulb housing.

8139
Technical data
Electrical systemBulbs
High-beam headlight H7 halogen bulb 12 V 55 W
Low-beam headlight H7 halogen bulb 12 V 55 W
Parking light 12 V 5 W
Brake/rear light 12 V 21/5W
Flashing turn indicators 12 V 10 W
Power socket
Ratings 12 V 5 A

i157
Index
Calling up settings, 49
Explanations, 49
Operation, 14FFront-wheel stand, 107
FuelFuel gauge, 20
Grade, 73
Quality, 137
Refuelling, 74
Reserve warning, 24
Fuel tank capacity, 74
Fuses, 138GGear indicator, 20
Gearbox Gear shifts, 64
Position on starting, 57
Technical data, 132
General view
Right side, 11 General view,
left side, 9
Grip heating, 15, 39
HHandlebar fitting Left, 14
Right, 15
Hazard warning flashers, 14, 36, 37
Headlight Adjustment for right-hand/left-
hand traffic, 42
Overview, 17
Headlight flasher, 14, 42
Helmet holder, 45
High-beam headlight
Bulb, 17
Replacing the bulb, 111
Switching on, 14, 42
Telltale light, 20
Horn, 14
IIgnition
Switching off, 34
Switching on, 34, 57
Inflation pressures, 130
Instrument cluster, 16JJump starting, 115KKeys Ignition keys, 34
Replacement keys, 35
Kill switch, 15, 38LLaying up, 124
Locking the handlebars, 35
Low-beam headlight
Bulb, 17
Replacing bulb, 110
Switching on, 41