bulb BUICK CENTURY 1994 Owners Manual

I I A green arrow on the
instrument panel will flash
in the direction of the turn
or lane change.
To signal a lane change,
just raise
or lower the lever
until the green arrow starts
to flash. Hold
it there until
you complete your lane
change. The lever will
return by itself when you
release it.
As you signal a turn or a lane change, if the arrows don’t
flash but just stay on, a signal bulb may be burned out
and other drivers won’t see your turn signal.
If a bulb is burned out, replace
it to help avoid an
accident. If the green arrows don’t go on at all when you
signal a turn, check the fuse (see “Fuses” in the Index)
and for burned-out bulbs.
nrn Signal Reminder
If your turn signal is left on for more than 3/4 of a mile,
a chime will sound.
To turn off the chime, move the turn
signal lever
to the off position.
Operation of Lights
Although your vehicle’s lighting system (headlights,
parking lights, fog lamps, side marker lights and
taillights) meets all applicable federal lighting
requirements, certain states and provinces may apply
their own lighting regulations that may require special
attention before you operate these lights.
For example, some jurisdictions may require that you
operate your fog lamps only when your lower beam
headlights are also on, or that headlights be turned on
whenever you must use your windshield wipers. In
addition, most jurisdictions prohibit driving solely with
parking lights, especially at dawn
or dusk. It is
recommended that you check with your own state or
provincial highway authority for applicable lighting
regulations.
90
ProCarManuals.com

Anti-Lock Brake System Active Light
LOW
TRACTION
When your anti-lock
system is adjusting
brake pressure to help
avoid a braking
skid, the
“LOW
TRACTION’ light
will come on.
Slippery road conditions will exist if this light comes on,
so adjust your driving accordingly. The light will stay on
for
a few seconds after the system stops adjusting brake
pressure. The
“LOW TRACTION” light also comes on
briefly, as a
bulb check, when the engine is started.
Engine Coolant Temperature Warning
Light
k F- 4ccN
TEMP
This light tells you that
your engine coolant has
overheated or your radiator
cooling fan is not working.
If you have been operating
your vehicle under normal
driving conditions, you
should pull off the road,
stop your vehicle and turn
the engine
off as soon as
possible.
The chapter “Problems on the Road,” in this manual
explains what to do. See “Engine Overheating” in the
Index.
ProCarManuals.com

I NOTICE:
If you keep driving your vehicle with this light on,
after a while the emission controls won’t work as
well, your fuel economy won’t be as good and your engine may not run as smoothly. This could
lead to costly repairs not covered by your
warranty.
Engine Oil Pressure Light
OIL
If you have a problem with
your oil, this light may stay
on after you start your
engine, or come
on when
you are driving. Stop your
car and shut off
the engine
if this light stays on. This
indicates that oil is not
going through your engine
quickly enough to keep
it
lubricated. The engine
could be low
on oil, or could have some
other oil problem. Have.your vehicle serviced
immediately.
The oil light could also come on in three other
situations:
0
0
0
When the ignition is on but the engine is not running,
the light will come on as a
test to show you it is
working, but
the light will go out when you turn the
ignition to “Start.” If
it doesn’t come on with the
ignition on,
you may have a problem with the fuse or
bulb. Have
it fixed right away.
Sometimes when the engine is idling at a stop, the
light may blink on and
off. This is normal.
If you make a hard stop, the light may come on for
a
moment. This is normal.
117
ProCarManuals.com

Passing
You’ll need more passing distance up ahead when
you’re towing a trailer. And, because you’re a good deal
longer, you’ll need to go much farther beyond the
passed vehicle before you can return to
your lane.
Backing Up
Hold the bottom of the steering wheel with one hand.
Then, to move the trailer to the left, just move that hand
to the left.
To move the trailer to the right, move your
hand to the right. Always back up slowly and,
if
possible, have someone guide you.
Making Turns
When you’re turning with a trailer, make wider turns
than normal.
Do this so your trailer won’t strike soft
shoulders, curbs, road signs, trees, or other objects.
Avoid jerky
or sudden maneuvers. Signal well in
advance.
Turn Signals When Towing a Trailer
When you tow a trailer, your vehicle has to have a
different turn signal flasher and extra wiring. The green arrows
on your instrument panel
will flash whenever
you signal
a turn or lane change. Properly hooked up,
the trailer lights
will also flash, telling other drivers
you’re about to turn, change lanes or stop.
When towing a trailer, the green arrows on your
instrument panel
will flash for turns even if the bulbs on
the trailer are burned out. Thus, you may
think drivers
behind you are seeing your signal when they are not. It’s
important to check occasionally to be sure
the trailer
bulbs are still working.
Driving On Grades
Reduce speed and shift to a lower gear before you start
down a long or steep downgrade.
If you don’t shift
down, you might have
to use your brakes so much that
they would get hot and no longer work well.
On a long
uphill grade, shift down and reduce your
speed to around 45
mph (70 km/h) to reduce the
possibility
of engine and transaxle overheating.
If you are towing a trailer that weighs more than 1,000
pounds (450
kg) and you have an automatic transaxle
with Overdrive, you may prefer to drive in “D” instead
of Overdrive.
An overdrive transmission is required if
towing a trailer more than 1,000 pounds (450 kg).
ProCarManuals.com

.
@) Part 6 Service and Appearance Care
~ ~~~~~
Here you will find information about the care of your Buick . This part begins with service and fuel information.
and then
it shows how to check important fluid and lubricant levels . There is also technical information about your
vehicle. and a section devoted to its appearance care
.
Part 6 includes:
Service ........................................................................\
..
Fuel ........................................................................\
.....
HoodRelease .....................................................................
EngineOil ....................................................................... \
Aircleaner ....................................................................... \
TransaxleFluid ....................................................................
Enginecoolant ....................................................................
Powersteering ....................................................................
Windshield Washer Fluid ............................................................
Brakes ........................................................................\
...
Battery ........................................................................\
..
BulbReplacement .................................................................
LoadingYourVehicle ...............................................................
Tires ........................................................................\
....
Appearancecare ..................................................................
Vehicle Identification Number (VIN) ..................................................
Fuses and Circuit Breakers ...........................................................
ReplacementBulbs .................................................................
Capacities and Specifications .........................................................
208
209
212
213 218
220
223
226
227
228
231
232
236 238
245
253
254 258
259
207
ProCarManuals.com

Halogen Bulbs
Headlamp Bulb Replacement
For the type of bulb, see the Index under "Replacement
Bulbs."
1. Turn the bulb assembly counterclockwise 1/6 turn,
pressing in firmly, until the flanges align with the
slots in
the retainer ring.
2. Pull out the bulb assembly.
3. Disconnect the bulb base from the wiring harness by
lifting the plastic locking tab.
To replace the bulb
assembly:
1.
2.
Snap a new bulb into
the wiring harness
(A).
Make sure the locking
tab
(B) is over the lock
(C).
Install the bulb
assembly by putting the
small tab
(D) in the
small notch in the
retainer ring
(E).
3. Turn the bulb assembly 1/6 turn clockwise to lock it
in place.
232
ProCarManuals.com

Front Turn and Parking Bulb and/or Side
Marker Bulb Replacement
1. Raise the hood.
2. Insert a screwdriver into the loop of the spring,
which can be seen just behind the bulb assembly.
3. Pull the spring to the rear and slightly toward the
outside
of the car until the detent releases from the
notch in the headlight mounting frame.
,I'
4. The bulb assembly is now loose. Pull it forward until
the bulb assembly can be reached.
To replace the turn/park bulb:
1. Rotate the bulb socket housing 1/4 turn
counterclockwise.
2. Push in and turn the bulb counterclockwise to
remove
it.
3. Put in the new bulb and turn it clockwise.
4. Snap the wire connector onto the bulb assembly.
233
ProCarManuals.com

. ..‘
To replace the side marker bulb:
1. Remove the socket by turning it counterclockwise
2. Remove the bulb by pulling it straight out of the
and
pulling it straight out.
socket.
3. Insert the new bulb by pressing it straight into the
socket.
4. Insert the socket by pressing it straight into the bulb
hole and turning it clockwise.
I
To reinstall the lamp:
1. Guide the latch spring
through the opening in
the metal inner panel.
2. Engage the two blades on the lamp into the slots on
the headlamp while engaging the two pins at the rear
of the lamp openings into the sockets on the rear of
the lamp. The lamp is now in place.
3. Insert a screwdriver into the loop on the latch spring.
Pull the spring to the rear and slightly center
of the
vehicle until the detent engages into the notch.
Taillight Bulb Replacement (Sedan)
For the type of bulb, see the Index under “Replacement
Bulbs.”
Replacing bulbs in the taillight housing is very difficult,
and we recommend that you see your dealer when you
need a bulb replaced.
ProCarManuals.com

Taillight Bulb Replacement (Wagon)
For the type of bulb, see the Index under “Replacement
Bulbs.”
1. Open the liftgate.
2. Remove the three Phillips head screws.
3. Pull the taillight housing away from the body of the
vehicle.
4. Press the bulb housing release lever and turn the
housing
1/6 turn counterclockwise to remove it.
5. To remove the bulb, push in and rotate it
counterclockwise.
6. Reverse all steps to reassemble the taillight.
235
ProCarManuals.com

~ ~~~ Replaceable Light Bulbs
Application Number
Exterior
Back-up Lamps ........................ 1156
Center High-Mounted Stoplamp Except Luggage Carrier Mounted
........ 1 141
Front Parking/Tum Signal Lamps
.......... 2057
Headlamps Low-Beam
.......................... 9006
High-Beam
.......................... 9005
License Plate Lamps
..................... 194
Rear Tail/Stop/Turn Signal Lamps
......... 2057
Tail Lamp Only
....................... 194
Tail/Stop Only
........................ 194
Front
................................ 194
Rear
................................. 24
Underhood Lamp
....................... 56 1
Luggage Carrier Mounted ............... 577
Sidemarker Lamps
Application Number
Interior
Air Conditioner/Heater Controls .......... T- 1 . 0
Ashtray ............................... 194
Cluster Lighting
........................ 161
Courtesy Lamps
........................ 561
Dome
............................... 2 1 1-2
Dome Courtesy
....................... 214-2
Domemeading Lamps
.................... 906
Gear Selector Indicator
................. 194G
GloveBox
............................. 174
Indicator Lamps
........................ 194
Indicator Lamp
. SRS .................... 195
Rear Compartment Lid Lamp
............. 1003
Rear Dome
. Wagon ................... 211-2
Turn Signal Indicators
.................... 194
Vanity Mirror
.......................... 124
Headlamp High-Beam
Indicator
............ 194
Map
.................................. 168
258
ProCarManuals.com