Dic BUICK LACROSSE 2007 Owner's Guide

Arming with the Power Lock Switch
The vehicle’s content theft-deterrent alarm system
can be activated when the key is removed from
the ignition and the power door lock switch
of either the driver’s or front passenger’s door is
used to lock the vehicle. The door needs to
be in the open position when pressing the power
door lock switch. The alarm system will not
activate if the door is closed when the power door
lock switch is pressed. This system can be
activated through the Driver Information Center
(DIC). See “CONTENT THEFT” under
“Customization Menu Items” inDIC Vehicle
Personalization on page 229.
When the doors are locked using the power door
lock switch of either front door, the red light on
top of the instrument panel will start ashing at a
fast rate, indicating that the system is arming.
After all the doors are locked there will be a time
delay and then the red light will begin to ash
at a very slow rate, indicating the system is armed.
Arming with the Remote Keyless Entry
Transmitter
The alarm system will arm when the remote keyless
entry transmitter is used to lock the doors after the
key is removed from the ignition. The red light will
come on to indicate that the system is arming. After
all doors are closed and locked, and after a time
delay, the red light will begin ashing at a very slow
rate to show the system is armed.
Arming Conrmation
A red light located on top of the instrument panel,
towards the center of the vehicle and near the
windshield, will ash slowly to conrm when
the system is armed.
Disarming with the Remote Keyless
Entry Transmitter
The alarm system will disarm when the remote
keyless entry transmitter is used to unlock
the doors. The red light will go out to show that
the system is disarmed.
105

Disarming with Your Key
The alarm system will disarm when the key is
used to unlock the doors. The red light will stop
ashing when the system is disarmed. If you would
like the key to disarm the alarm system, see
“CONTENT THEFT” underDIC Vehicle
Personalization on page 229for more information.
PASS-Key®III
Your PASS-Key®III system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry
Canada.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
Changes or modications to this system by other
than an authorized service facility could void
authorization to use this equipment.
PASS-Key®III uses a radio frequency transponder
in the key that matches a decoder in your vehicle.
106

PASS-Key®III Operation
Your vehicle is equipped
with PASS-Key®III
(Personalized
Automotive Security
System) theft-deterrent
system.
PASS-Key
®III is a passive theft-deterrent system.
This means nothing special needs to be done
to arm or disarm the system. It works when the key
is inserted or removed from the ignition.
PASS-Key III
®uses a transponder in the ignition
key that matches a decoder in the vehicle.
When the PASS-Key
®III system senses that the
wrong key has been inserted into the ignition, it
shuts down the vehicle’s starter and fuel systems.The starter will not work and fuel will stop owing to
the engine. If someone tries to start the vehicle
again with the wrong key, the vehicle will not start.
Anyone using a trial-and-error method to start the
vehicle will be discouraged to do so because of the
high number of electrical key codes.
When trying to start the vehicle, if the engine does
not start and the STARTING DISABLED warning
message on the Driver Information Center
(DIC) comes on, the key may have a damaged
transponder. Turn the ignition off and try again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition
key. At this time, you may also want to check the
fuse. SeeFuses and Circuit Breakers on
page 450. If the engine still does not start with the
other key, the vehicle needs service. If the
vehicle does start, the rst key may be faulty. See
your dealer who can service the PASS-Key
®III
to have a new key made. In an emergency,
contact Roadside Assistance. SeeRoadside
Assistance Program on page 484for more
information.
107

It is possible for the PASS-Key®III decoder to
accept the transponder value of a new or
replacement key. Up to 10 keys may be
programmed for the vehicle. The following
procedure is for programming additional keys only.
If all the programmed keys are lost or do not
operate, see your dealer or a locksmith who can
service PASS-Key
®III to have keys made and
programmed to the system.
To program the new key do the following:
1. Verify that the new key has PK3 stamped
on it.
2. Insert the master key in the ignition and start
the engine. If the engine will not start, see
your dealer for service.
3. After the engine has started, turn the key to
OFF, and remove the key.
4. Insert the key to be programmed and turn it to
RUN within ve seconds of removing the
original key.5. The SERVICE THEFT SYSTEM warning
message on the DIC will turn off, once the
key has been programmed. It may not
be apparent that the SERVICE THEFT
SYSTEM warning message went on due to
how quickly the key is programmed.
6. Repeat Steps 1 through 5 if additional keys
are to be programmed.
If the SERVICE THEFT SYSTEM warning
message appears and stays on the DIC while the
vehicle is being driven, the engine will be able
to be restarted if it is turned off. Your
PASS-Key
®III system, however, is not working
properly and must be serviced by your dealer.
The vehicle is not protected by the PASS-Key
®III
system at this time.
If the PASS-Key
®III key is lost or stolen, see your
dealer or a locksmith who can service
PASS-Key
®III to have a new key made.
108

B (ACCESSORY):This position lets the radio and
windshield wipers operate while the engine is
off. To use ACCESSORY, turn the key clockwise.
C (RUN):This position is where the key returns
to after the vehicle is started. This position displays
some of the warning and indicator lights.
The battery could be drained if you leave the key
in the ACCESSORY or RUN position with the
engine off. You may not be able to start your
vehicle if the battery is allowed to drain for
an extended period of time.
D (START):This position starts the engine.
A warning chime will sound and the Driver
Information Center (DIC) will display DRIVER’S
DOOR AJAR when the driver’s door is opened if
the ignition is in OFF, ACCESSORY and the key is
in the ignition. SeeDIC Warnings and Messages
on page 208for more information.Key In the Ignition
Never leave your vehicle with the keys inside, as it
is an easy target for joy riders or thieves. If you
leave the key in the ignition and park your vehicle,
a chime will sound, when you open the driver’s
door. Always remember to remove your key from
the ignition and take it with you. This will lock
your ignition and transaxle. Also, always remember
to lock the doors.
The battery could be drained if you leave the key
in the ignition while your vehicle is parked.
You may not be able to start your vehicle after it
has been parked for an extended period of time.
Retained Accessory Power (RAP)
If the vehicle has Retained Accessory Power
(RAP), the power windows and radio will continue
to operate for up to 10 minutes after the ignition
key is turned to OFF unless a door is opened.
110

Automatic Transaxle Operation
Your vehicle’s automatic
transaxle may have a
shift lever on the
steering column or on
the console between
the seats.
There is also a display
located on the
instrument panel cluster
that indicates the
vehicle’s gear position.{CAUTION:
It is dangerous to get out of your vehicle
if the shift lever is not fully in PARK (P)
with the parking brake rmly set. Your
vehicle can roll.
Do not leave your vehicle when the engine
is running unless you have to. If you have
left the engine running, the vehicle can
move suddenly. You or others could be
injured. To be sure your vehicle will not
move, even when you are on fairly level
ground, always set your parking brake and
move the shift lever to PARK (P). See
Shifting Into Park (P) on page 118.Ifyou
are pulling a trailer, seeTowing a Trailer on
page 327.
The positions for the shift lever are:
PARK (P): This position locks the vehicle’s front
wheels. It is the best position to use when the
engine is started because the vehicle cannot
move easily.
Console Shift Lever
114

Parking Brake
To set the parking
brake, hold the regular
brake pedal down
with your right foot.
Push down the parking
brake pedal with
your left foot.
To release the parking brake, hold the regular
brake pedal down with your right foot and push the
parking brake pedal with your left foot. While
you lift your left foot, the parking brake pedal will
follow it to the released position.A warning chime will sound and PARKING
BRAKE ON will display in the DIC if the parking
brake is set, the ignition is on, and the vehicle
speed is greater than 5 mph (8km/h). For more
information seeBrake System Warning Light
on page 186andDIC Warnings and Messages
on page 208.
Notice:Driving with the parking brake on
can overheat the brake system and cause
premature wear or damage to brake system
parts. Verify that the parking brake is fully
released and the brake warning light is
off before driving.
If you are towing a trailer and parking on any
hill, seeTowing a Trailer on page 327. That
section shows what to do rst to keep the trailer
from moving.
117

3. Enter these positions into the Universal Home
Remote System as follows.
Press and release all three buttons at the same
time to put the device into programming mode.
4. The indicator light will blink slowly. In order
from left to right, and within two and one-half
minutes, enter each switch setting into the
Universal Home Remote System. Push
one button for each switch as follows:
Left button = “on” switch position.
Right button = “off” switch position.
Middle button = “middle” switch position.5. After entering the switch settings, press and
release all three buttons at the same time.
The indicator lights will turn on.
6. Press and hold the button you would like to
use to control the garage door until the
garage door moves. The indicator light above
the selected button should slowly blink.
You may need to hold the button from ve to
55 seconds.
7. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
8. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1–8, choosing a
different function button in Step 7 than what you
used for the garage door opener.
134

3. Press and hold the button you would like to
use to control the garage door until the
garage door moves. The indicator light, above
the selected button, should slowly blink.
You may need to hold the button from ve to
20 seconds.
4. Immediately release the button when the
garage door moves. The indicator light will
blink rapidly until programming is complete.
5. Press and release the button again. The
garage door should move, conrming that
programming is successful and complete.
To program another device such as an additional
garage door opener, a security device, or
home lighting, repeat Steps 1–5, choosing a
different function button in Step 3 than what you
used for the garage door opener.
Using Universal Home Remote
Press and hold the appropriate button for at least
half of a second. The indicator light will come
on while the signal is being transmitted.
Reprogramming Universal Home
Remote Buttons
You can reprogram any of the three buttons by
repeating the instructions.
Erasing Universal Home Remote
Buttons
You should erase the programmed buttons when
you sell the vehicle or terminate your lease.
To erase either rolling code or xed code on the
Universal Home Remote device, do the following:
1. Press and hold the two outside buttons at
the same time for approximately 20 seconds,
until the indicator lights, located directly
above the buttons, begin to blink rapidly.
2. Once the indicator lights begin to blink,
release both buttons. The codes from all
button will be erased.
For additional information on Universal Home
Remote, seeCustomer Assistance Offices
on page 482.
136

Programming Universal Home Remote
Follow these steps to program up to three
channels:
1. Press and hold down the two outside
Universal Home Remote buttons, releasing
only when the Universal Home Remote
indicator light begins to ash, after
20 seconds. Do not hold down the buttons for
longer than 30 seconds and do not repeat
this step to program a second and/or
third hand-held transmitter to the remaining
two Universal Home Remote buttons.
2. Position the end of your hand-held transmitter
about 1 to 3 inches (3 to 8 cm) away from the
Universal Home Remote buttons while
keeping the indicator light in view.
3. Simultaneously press and hold both the
desired Universal Home Remote button
and the hand-held transmitter button. Do not
release the buttons until Step 4 has been
completed.
Some entry gates and garage door openers
may require you to substitute Step 3 with
the procedure noted in “Gate Operator and
Canadian Programming” later in this section.4. The indicator light will ash slowly at rst and
then rapidly after Universal Home Remote
successfully receives the frequency signal
from the hand-held transmitter. Release both
buttons.
5. Press and hold the newly-trained Universal
Home Remote button and observe the
indicator light.
If the indicator light stays on continuously,
programming is complete and your device
should activate when the Universal Home
Remote button is pressed and released.
To program the remaining two Universal Home
Remote buttons, begin with Step 2 under
“Programming Universal Home Remote.”
Do not repeat Step 1 as this will erase all of
the programmed channels.
If the indicator light blinks rapidly for two
seconds and then turns to a constant light,
continue with Steps 6 through 8 following
to complete the programming of a rolling-code
equipped device, most commonly, a garage
door opener.
138