set clock BUICK LACROSSE 2007 Owner's Manual

Interior Lamps
Your interior lamps
control is located next to
the exterior lamps
control and to the left of
the steering wheel on
the instrument panel.
9(Off):Turn the control to this position to
disable courtesy lamps, entry lighting, delayed
entry lighting, and delayed exit lighting.
1(Door):Turn the control to this position to turn
the interior lamps on when any door is open and
when the ignition key is removed from the ignition.
+(On):Turn the control to this position to turn
on the interior lamps.
The interior lamps can be controlled, or
automatically turned on or off under certain
conditions. They are explained in the following text.
Instrument Panel Brightness
The instrument panel lights can be brightened or
dimmed by pressing the center knob of the
interior lamp controls until it pops out. Turn the
knob clockwise to brighten the lights or
counterclockwise to dim them.
Courtesy Lamps
Courtesy lamps come on to make it easier to
enter and exit the vehicle. These lamps will come
on when the interior lamp control is in the door
position and any door is opened.
Entry Lighting
The courtesy lamps will come on and stay on for a
set time whenever the interior lamp control is in
the door position and the UNLOCK button on
the Remote Keyless Entry (RKE) transmitter is
pressed.
The lamps will stay on while a door is opened and
then turn off automatically about 25 seconds
after it is closed. If the UNLOCK button is pressed
and a door is not opened, the lamps will turn off
after about 25 seconds.
161

There is also a retroactive trip odometer function
that performs the following for each trip odometer:
If the vehicle’s speed has exceeded 3 mph
(5 km/h) during the current ignition cycle, this
function will set the trip odometer to the
distance driven during the current ignition cycle.
If the vehicle’s speed has not exceeded 3 mph
(5 km/h), this function will set the trip odometer
to the distance driven during the previous
ignition cycle plus the distance driven during
the current ignition cycle.
Press and hold the set/reset button on the uplevel
vehicle or the trip/odometer button on the base
level vehicle for three seconds, then release
the button. The retroactive trip odometer value will
be set into the currently displayed trip odometer.
Time Elapsed (Uplevel Only)
Press the trip/odometer button until TIME
ELAPSED :00 displays. This mode is like a
stopwatch, in that you can clock the time it takes
to get from one point to another. Each of the
elds for the hours, minutes, and seconds are
two numeric digits.Once TIME ELAPSED :00 is displayed, press the
set/reset button on the uplevel vehicle to start
the timing feature. Press the set/reset button again
to stop it. If you will be starting and stopping
your vehicle, during a trip for instance, the TIME
ELAPSED feature will automatically start timing
where it left off when you last stopped. To reset it,
press and hold the set/reset button for about
1.5 seconds. The display will return to zero. Press
the trip/odometer button to exit from the TIME
ELAPSED display.
Average Speed (Uplevel Only)
Press the trip/odometer button until AVERAGE
SPEED displays. This mode shows the average
speed of the vehicle in miles per hour (mph)
or kilometers per hour (km/h). This average is
calculated based on the various vehicle speed
recorded since the last reset of this value. To reset
the value, press the trip/odometer button to
display AVERAGE SPEED, then press and hold
the set/reset button on the uplevel vehicle.
The display will return to zero.
202

2. Use the wheel wrench to loosen the plastic
wheel nut caps, if the vehicle has them, in a
counterclockwise direction.
If needed, nish loosening them by hand.
The nut caps will not come off of the wheel
cover.
3. Use the at end of the wheel wrench and pry
along the edge of the cover until it comes off.
Pull off the wheel cover and set it aside.
The edge of the wheel cover could be sharp,
so do not try to remove the cover with your
bare hands. Do not drop the cap or lay it face
down, as it could become scratched or
damaged.
If the vehicle has aluminum wheels and wheel
center caps, the wheel nuts are hidden behind the
center cap. Remove the center cap by using
the at end of the wheel wrench at the notch.
Do not drop the cap or lay it facedown, as it could
become scratched or damaged.Once you have removed the wheel cover or
center cap, use the following procedure to remove
the at tire and install the spare tire.
1. Place the wheel wrench securely over
the wheel nut. Turn the wheel wrench
counterclockwise to loosen all the wheel
nuts, but do no remove them yet.
2. Turn the jack handle clockwise to raise
the jack lift head.
Removing the Wheel Nuts
430