BUICK RANDEZVOUS 2007 Owner's Manual

Power Windows
Switches on the driver’s door armrest control
each of the windows when the ignition is in ON,
ACCESSORY, or when Retained Accessory
Power (RAP) is active. SeeRetained Accessory
Power (RAP) on page 129for more information.
In addition, each passenger’s door has a window
switch.The driver’s power window switch has two down
positions. Push the rear of the switch to the
rst position to lower the window normally.
Press the rear of any passenger window switch
and that window will open. Press the front of
any switch to close the window.
Express-Down Window
The driver’s window switch also has an
express-down feature. This switch is labeled
AUTO. To activate the express-down feature, push
the rear of the driver’s window switch to the
second position, then release it. The window will
lower completely.
To stop the window while it is lowering, press the
front of the switch. To raise the window, press
and hold the front of the switch.
Window Lockout
The driver’s window controls also include a
lockout switch. Press the right side of the WDO
LOCK switch to stop rear passengers from
lowering their window. The driver can still control
all of the windows with the lockout on. Press
the other side of the WDO LOCK switch for normal
window operation.
121

Sun Visors
To block out glare you can swing down the visors.
You can also remove them from the center
mount and swing them to the side. There may be
an extension on the inboard side of the sun
visors. Pull the extension out to block out glare.
Visor Vanity Mirror
Pull down the sun visor. Flip up the cover to
expose the vanity mirror.
Lighted Visor Vanity Mirrors
If your vehicle has this feature, pull down the sun
visor. Flip up the cover to expose the vanity
mirror. The lamps will come on when you open
the cover.
Theft-Deterrent Systems
Vehicle theft is big business, especially in some
cities. Although your vehicle has a number of
theft-deterrent features, we know that nothing we
put on it can make it impossible to steal.
Content Theft-Deterrent
Your vehicle may have a theft-deterrent alarm
system.
A security light, located
on top of the instrument
panel will ash slowly
to let you know that the
system has been
armed.
While armed, the doors will not unlock with the
power door lock switch.
Once armed, the alarm will go off if someone tries
to enter the vehicle without using the optional
remote keyless entry transmitter or the key, or tries
to turn the ignition on without using the correct
key. The horn will sound and the headlamps and
parking lamps will ash any time the alarm
sounds.
122

When the content theft-deterrent system is armed,
the liftgate may be opened by pressing the
REAR button on the remote keyless entry
transmitter. The alarm will go into standby mode.
Once the liftgate is closed, the alarm will be
armed. See “Liftgate Release” underLiftgate on
page 118for more information on how to open the
liftgate.
Arming with the Power Lock Switch
The content theft-deterrent alarm system will arm
when you use either power door lock switch to
lock the doors while any door or the liftgate is open
and the key is removed from the ignition. The
security light, located on top of the instrument
panel, will start ashing when the system is armed.
Within ve seconds, after the security light
begins to ash, any door can be manually
unlocked and opened, without sounding the alarm.
A door unlocked manually will remain unlocked
until locked again.
Arming with the Remote Keyless
Entry Transmitter
Your alarm system will arm when you press LOCK
once on your remote keyless entry transmitter
to lock the doors. The alarm system light will come
on for 30 seconds and then start ashing to let
you know the system is armed.
Within the 30 second delay after the security light
comes on, and an additional ve seconds after
the light begins to ash, any door can be manually
unlocked and opened, without sounding the
alarm.
If LOCK is pressed on your remote keyless entry
transmitter twice within ve seconds, any door
can be manually unlocked and opened within ve
seconds after the security light begins to ash,
without sounding the alarm. A door unlocked
manually will remain unlocked until locked again.
Disarming with Your Key
Your alarm system will disarm when you use your
key to unlock the driver’s door. The security
light will stop ashing to let you know the system
is no longer armed.
123

Disarming with the Remote Keyless
Entry Transmitter
Your alarm system will disarm when you press
UNLOCK on your remote keyless entry transmitter
to unlock the doors. The security light, on top of
the instrument panel, will stop ashing to let
you know the system is no longer armed.
PASS-Key®III
Your PASS-Key®III system operates on a radio
frequency subject to Federal Communications
Commission (FCC) Rules and with Industry
Canada.
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful
interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation.This device complies with RSS-210 of Industry
Canada. Operation is subject to the following
two conditions:
1. This device may not cause interference.
2. This device must accept any interference
received, including interference that may
cause undesired operation of the device.
Changes or modications to this system by other
than an authorized service facility could void
authorization to use this equipment.
PASS-Key®III uses a radio frequency transponder
in the key that matches a decoder in your
vehicle.
124

PASS-Key®III Operation
Your vehicle is equipped
with the PASS-Key®III
(Personalized
Automotive Security
System) theft-deterrent
system.
PASS-Key
®III is a passive theft deterrent system.
This means you do not have to do anything different
to arm or disarm the system. It works when you
insert or remove the key from the ignition.When the PASS-Key
®III system senses that
someone is using the wrong key, it shuts down the
vehicle’s starter and fuel systems. The starter will
not work and fuel will stop being delivered to the
engine. Anyone using a trial-and-error method to
start the vehicle will be discouraged because of the
high number of electrical key codes.
If the SECURITY message is shown on the
Message Center when trying to start the vehicle,
the key may have a damaged transponder.
See “PASS-Key
®III Security Message” under
Message Center on page 225. Turn the ignition off
and try to start the vehicle again.
If the engine still does not start, and the key
appears to be undamaged, try another ignition
key. At this time, you may also want to check the
fuse. SeeFuses and Circuit Breakers on
page 463. If the engine still does not start with the
other key, your vehicle needs service. If your
vehicle does start, the rst key may be faulty. See
your dealer who can service the PASS-Key
®III
to have a new key made.
125

It is possible for the PASS-Key®III decoder to
program the transponder value of a new or
replacement key. Up to 10 additional keys may be
programmed for the vehicle. This procedure is
for programming additional keys only. If all
the currently programmed keys are lost or do not
operate, you must see your GM dealer or a
locksmith who can service PASS-Key
®III to have
keys made and programmed to the system.
See your GM dealer who can service
PASS-Key
®III to get a new key blank that is a cut
exactly as the ignition key that operates the
system.
Canadian Owners:If you lose or damage your
keys, only a GM dealer can service PASS-Key
®III
to have new keys made. To program additional
keys you will need two current driver’s keys, black
in color. You must add a step to the following
procedure. After Step 3 repeat Steps 1 through 3
with the second current driver’s key. Then
continue with Step 4.To program the new PK3
®key do the following:
1. Verify the new key has PK3 stamped on it.
2. Insert the original key in the ignition and start
the engine. If the engine will not start, see
your GM dealer for service.
3. After the engine has started, turn the key to
OFF, and remove the key.
4. Insert the key to be programmed and turn it to
ON within 10 seconds of removing the
previous key.
5. The SECURITY message will turn off once
the key has been programmed. It may not
be apparent that the SECURITY message
went on due to how quickly the key is
programmed.
6. Repeat Steps 1 through 4 if additional keys
are to be programmed.
If you are ever driving and the SECURITY
message comes on and stays on, you will be able
to restart your engine if you turn it off. Your
PASS-Key
®III system, however, is not working
properly and must be serviced by your GM dealer.
Your vehicle is not protected by the PASS-Key
®III
system at this time.
126

If you lose or damage a PASS-Key®III key, see
your GM dealer who can service PASS-Key®III to
have a new key made.
Starting and Operating Your
Vehicle
New Vehicle Break-In
Notice:Your vehicle does not need an
elaborate break-in. But it will perform better in
the long run if you follow these guidelines:
If you have all-wheel drive, keep your
speed at 55 mph (88 km/h) or less for
the rst 500 miles (805 km).
Do not drive at any one constant speed,
fast or slow, for the rst 500 miles
(805 km). Do not make full-throttle starts.
Avoid downshifting to brake, or slow,
the vehicle.
Avoid making hard stops for the rst
200 miles (322 km) or so. During this time
your new brake linings are not yet broken
in. Hard stops with new linings can mean
premature wear and earlier replacement.
Follow this breaking-in guideline every time
you get new brake linings.
Do not tow a trailer during break-in. See
Towing a Trailer on page 340for the trailer
towing capabilities of your vehicle and more
information.
Following break-in, engine speed and load can
be gradually increased.
127

Ignition Positions
With the key in the ignition, you can turn it to four
different positions.
A (OFF):This is the only position in which you
can remove the key. This position locks the ignition
and transaxle.
Notice:Using a tool to force the key from the
ignition switch could cause damage or break
the key. Use the correct key and turn the key
only with your hand. Make sure the key is all the
way in. If none of this works, then your vehicle
needs service.B (ACCESSORY):This position allows you to use
things like the radio and the windshield wipers
while the engine is off. This position will also allow
you to turn off the engine. Use ACCESSORY if
you must have your vehicle in motion while
the engine is off, for example, if your vehicle is
being pushed or towed.
C (ON):This is the position that the switch
returns to after you start your engine and release
the key. The switch stays in ON when the
engine is running. But even when the engine is
not running, you can use ON to operate your
electrical power accessories, and to display some
instrument panel warning lights.
The battery could be drained if you leave the key
in the ACCESSORY or On position with the
engine off. You may not be able to start your
vehicle if the battery is allowed to drain for
an extended period of time.
D (START):This position starts the engine. When
the engine starts, release the key. The ignition
switch will return to ON for normal driving.
128

Key In the Ignition
Never leave your vehicle with the keys inside, as it
is an easy target for joy riders or thieves. If you
leave the key in the ignition and park your vehicle,
a chime will sound, when you open the driver’s
door. Always remember to remove your key from
the ignition and take it with you. This will lock
your ignition and transaxle. Also, always remember
to lock the doors.
The battery could be drained if you leave the key
in the ignition while your vehicle is parked.
You may not be able to start your vehicle after it
has been parked for an extended period of time.
Retained Accessory Power (RAP)
With RAP, the power windows, the audio system,
the sunroof and the automatic level control will
continue to work for up to 10 minutes after
the ignition key is turned to OFF or until one of the
doors is opened.
Starting the Engine
Move your shift lever to PARK (P) or
NEUTRAL (N). Your engine will not start in
any other position — that is a safety feature.
To restart when you are already moving,
use NEUTRAL (N) only.
Notice:Shifting into PARK (P) with the vehicle
moving could damage the transaxle. Shift into
PARK (P) only when your vehicle is stopped.
1. With your foot off the accelerator pedal, turn
your ignition key to START. When the engine
starts, let go of the key. The idle speed will
go down as your engine warms up. Do
not race the engine immediately after starting
it. Operate the engine and transaxle gently
until the oil warms up and lubricates all moving
parts.
129

Your vehicle has a Computer-Controlled
Cranking System. This feature assists in
starting the engine and protects the electrical
system. If the ignition key is turned to the
START position, and then released when the
engine begins cranking, the engine will
continue cranking until the vehicle starts or
until it exceeds the maximum cranking
time allowed, approximately 15 seconds to
prevent cranking motor damage. To prevent
starter-motor gear damage, this system
also prevents cranking if the engine is already
running. The engine cranking can be
stopped by turning the ignition switch to the
ACCESSORY or LOCK position.
Notice:Holding your key in START for longer
than 15 seconds at a time will cause your
battery to be drained much sooner. And the
excessive heat can damage your starter motor.
Wait about 15 seconds between each try to
help avoid draining your battery or damaging
your starter.2. If the engine does not start in 10 seconds,
push the accelerator pedal about one-quarter
of the way down while you turn the key to
START. Do this until the engine starts.
As soon as it does, let go of the key.
3. If your engine still will not start, or starts but
then stops, it could be ooded with too much
gasoline. Try pushing your accelerator
pedal all the way to the oor and holding it
there as you hold the key in START for
a maximum of 15 seconds. This clears the
extra gasoline from the engine. If the engine
still will not start, or starts briey but then
stops again, repeat Step 1 or 2, depending on
the temperature. When the engine starts,
release the key and the accelerator pedal.
Notice:Your engine is designed to work with
the electronics in your vehicle. If you add
electrical parts or accessories, you could
change the way the engine operates. Before
adding electrical equipment, check with
your dealer. If you do not, your engine might
not perform properly. Any resulting damage
would not be covered by your vehicle’s
warranty.
130