high beam CADILLAC CATERA 1998 1.G Owners Manual

Downloaded from www.Manualslib.com manuals search engine Headlamp HighLow Beam Windshield Wipers
With the twilight sentinel on or with the lamp control
dial turned to the headlamp position, push the turn
signal lever on the driver’s
side of the steering wheel
away from you to turn on the high-beam headlamps.
This light on the instrument
panel will be on, indicating
high-beam usage.
Pull the lever back to the original position to return to
low-beam headlamps. For more information, see
“Headlamps” later in this section.
Flash-To-Pass
This feature uses the high-beam headlamps to signal the
driver in front of you that you want to pass.
To use, pull the turn signal lever toward you and release.
WIPER: Move the lever on the passenger’s side of the
steering wheel up and down to control the wipers.
MIST Tap the lever up and then release it for a single
wipe cycle. For more cycles, pull and hold the lever.
= (HIGH): Move the lever all the way up for a fast
wiper speed.
- (LOW): The third position up controls the low wiper
speed.
-- (DELAY): This is for a controlled delay setting.
Rotate the control dial
on the lever to increase or
decrease the delay between wipe cycles.
o (OFF): This Dosition turns off the wipers.
2-34

Downloaded from www.Manualslib.com manuals search engine ‘00s 0 Parking lamps, front and rear sidemarker
lamps, taillamps, license plate lamps, ashtray lamps,
backlighting to the radio controls and instrument
panel lights.
so Headlamps.
$0 Fog lamps.
Twilight sentinel.
OFF Turns the twilight sentinel system off.
Instrument panel brightness control.
Turn the lamp control dial to the right (to the first
position) to turn
on the parking lamps, front and rear
sidemarker lamps, taillamps, license plate lamps, ashtray
lamps, instrument panel lights and backlighting to the
center console controls. Turn the lamp control dial all
the way to the right (to the second position) to turn on
the low-beam headlamps.
Turn the lamp control dial
to the left to turn the
lamps off.
Headlamps
Turn the lamp control dial all the way to the right to turn
on the low-beam headlamps.
10 turn on the high-beam headlamps, the low-beam
headlamps must already be on. Push the turn signal lever
on the left side of the steering wheel away from you to
engage the high-beam headlamps. Pull the lever toward
you to return to the low-beam headlamps. For more
information, see “Headlamp High/Low Changer” earlier
in this section.
Turn the lamp control dial all the way to the left to turn
the headlamps
off.
Note that if the headlamps are activated while driving
and then you turn your vehicle’s ignition off while the
lamp dial is still turned
on, the headlamps will turn off.
If, however, you open the driver’s door while the lamp
dial is still turned on, a warning chime will sound
reminding you to turn the lamp control dial to
OFF. This
will stop the warning chime from sounding. (If you want
the headlamps to remain on, you must manually turn the
lamp control dial
off and then back on to the headlamp
position. The headlamps will stay on until manually
turned off again.)

Downloaded from www.Manualslib.com manuals search engine Wiper-Activated Headlamps
This feature activates the low-beam headlamps, parking
lamps, sidemarker lamps and taillamps after the
windshield wipers have been in use for about
20 seconds.
The wiper-activated headlamps light the way in poor
weather and
also make your vehicle more visible to
other drivers.
If the wipers are on and the ignition switch
is turned off, the headlamps will immediately turn off.
The headlamps will also deactivate if the windshield
wipers have been turned
off for about 20 seconds.
Perimeter Lighting
This feature turns on the low-beam headlamps,
parking lamps, sidemarker lamps and taillamps for
about
20 seconds after the unlock button on the remote
keyless entry transmitter is pressed. Perimeter lighting
immediately ends when your vehicle’s ignition is turned
to
ON or START.
Lamps On Reminder
You will hear a warning chime if you open the door
while leaving the lamps on, if the manual headlamp
control is activated. An exception to this is when you’re
using the twilight sentinel.
Daytime Running Lamps
Daytime Running Lamps (DRL) can make it easier for
others to see the front of your vehicle during the day.
DIU, can be helpful in many different driving
conditions, but they can be especially helpful in the short periods after dawn and before sunset.
The DRL system will make the high-beam headlamps
come on at reduced brightness when:
your vehicle’s ignition is in ON or START,
the low-beam headlamps are off (the manual lamp
switch is in the off or park lamp position) and
your vehicle’s transmission is shifted out of
PARK
(P).
When DRL are on, only the high-beam headlamps (at
reduced brightness) will be on.
No other exterior lamps
such as
the parking lamps, taillamps, etc. will be on
when the DRL
are being used. The instrument panel
won’t be lit up either.
When the twilight sentinel is on and it’s dark enough
outside, the high-beam headlamps (at reduced intensity)
will change to low-beam headlamps. When it’s bright
enough outside, the regular lamps will go off, and the
high-beam headlamps change to the reduced brightness
of
DRL.
2-41
__

Downloaded from www.Manualslib.com manuals search engine Fog Lamps Cornering Lamps
Use
the fog lamps for better
vision in foggy or misty
conditions.
Press this button
to turn the fog lamps on and
press the button again to
I turn the lamps off. (The fog
lamps only work when the
parking lamps or the
low-beam headlamps
are on.)
I
This light on the instrument
panel will come on
when the fog lamp button
is pressed. 50
I
If you turn on the high-beam headlamps, the fog lamps
will turn
off. They'll turn back on again when you
switch to low-beam headlamps. The
cornering lamps come
on when the headlamps or
parking lamps are on and you signal a turn. They
provide more light for cornering.
Twilight Sentinel
This feature is below the
lamp control dial on the left
side
of the instrument panel.
It automatically switches
the parking lamps and
low-beam headlamps on
and off by sensing how dark
it is outside.
To operate the twilight sentinel, the ignition must be in
ON or START and the twilight sentinel must be turned
on by pressing the
OFF button (an indicator light in the
button will be
off when the twilight sentinel is
activated). If the system senses it is dark outside, the
lamps will turn on. The lamps turn off when the system
detects that it is bright outside.

Downloaded from www.Manualslib.com manuals search engine You can be temporarily blinded by approaching
headlamps. It can take
a second or two, or even several
seconds, for your eyes to readjust to the dark. When
you are faced with severe glare (as from a driver who
doesn't lower the high beams, or
a vehicle with
misaimed headlamps), slow down a little. Avoid
staring directly into the approaching headlamps.
Keep your windshield and all the glass on your vehicle
clean
-- inside and out. Glare at night is made much
worse by dirt on the glass. Even the inside of the glass
can build
up a film caused by dust. Dirty glass makes
lights dazzle and flash more than clean glass would,
making the pupils
of your eyes contract repeatedly.
Remember that your headlamps light
up far less of a
roadway when you are in a turn or curve. Keep your
eyes moving; that way, it's easier to pick out dimly
lighted objects. Just as your headlamps should be
checked regularly for proper aim,
so should your eyes
be examined regularly. Some drivers suffer from night
blindness
-- the inability to see in dim light -- and
aren't even aware
of it.
Driving in Rain and on Wet Roads
Rain and wet roads can mean driving trouble. On a wet
road, you can't stop, accelerate or turn as well because
your tire-to-road traction isn't as good as on dry roads.
And, if your tires don't have much tread left, you'll get
even less traction. It's always wise
to go slower and be
cautious if rain
starts to fall while you are driving. The
surface may get wet suddenly when your reflexes
are
tuned for driving on dry pavement.

Downloaded from www.Manualslib.com manuals search engine Bulb Replacement
I
~ For bulb types, see “Replacement Bulbs” in the Index.
1 Halogen Bulbs
I I
Halogen bulbs have pressurized gas inside and
can burst
if you drop or scratch the bulb. You or
others could be injured. Be sure to read and
follow the instructions on the bulb package.
Headlamps
1. With a screwdriver, unscrew the fastener on the
headlamp cover and then remove the cover to gain access to the headlamps. Note that the inner bulb
is
for the low-beam headlamp and the outer bulb is for
the high-beam headlamp.
6-30

Downloaded from www.Manualslib.com manuals search engine It is recommended that the upper limit not exceed plus
0.4 degrees from the center of the bubble. Other drivers
may flash their high beams at you
if your adjustment is
much above plus
0.4 degrees.
If you find that the headlamp aiming needs adjustment,
follow these steps:
1. With a screwdriver, unscrew the fastener on the
headlamp cover and then remove the cover to be able
to see the back of the headlamp assembly.
2. Check the vertical aim for each headlamp and adjust
it as necessary. The vertical aim adjustment screw is
located on the outboard side
of the headlamp
assembly. You can see the level through the
headlamp assembly.
Turn the vertical aiming screw
until the bubble in the level
is centered at 0 (zero).
3. If the horizontal aim needs adjusting, see
your dealer.
Adjustment screws can be turned with an
E8 Tom@
socket
or a T15 Torx screwdriver.
6-34

Downloaded from www.Manualslib.com manuals search engine Front %rn Signal Lamp
1. With a screwdriver, unscrew the fastener on the headlamp cover and then remove
it to access the turn
signal lamps (see Step
1 under “Headlamps”).
3. Pull the bulb out to replace and then reassemble.
2. On the outboard side of each low-beam headlamp,
you
will find the turn signal bulbs. Turn the lamp
assembly to the left to remove.
Center High-Mounted Stoplamp (CHMSL)
The CHMSL is equipped with high durability
illumination.
If a bulb problem does occur, see your
dealer for assistance.
6-35

Downloaded from www.Manualslib.com manuals search engine Fuse Usage Usage
16
17
18
19
20
21
22
23
24
25
26 Cigarette Lighter (Front and Console)
Horn #1 and #2
Fuel Pump
Electronic BrakeD'raction Control Module
Passenger and Driver Heated Seat Relay
Daytime Running Lamp (DRL) Relay,
LH High-Beam Headlamp Relay
Headlamp
Switch, LH Headlamp
(Low Beam)
LH Parking Lamp and
Turn Signal Lamp,
LH Rear Sidemarker Lamp, Multifunction
Relay, LH Stoplamp and Taillamp
Lifting Magnet, BCM, Gage Cluster Sunroof Actuator
Headlamp Switch, RH and LH Front
Sidemarker Lamp, Middle Taillamp, RH
and LH Rear License Plate Lamp, Radio,
Automatic Transmission Control
Indicator, Heater and A/C Control
Fuse
27
28 29
30
31
32
33
34
35 Automatic Level Control Sensor, Rear
Suspension Leveling Air Compressor
and Relay
Remote Control Door Lock Receiver, Door Lock Relay, Rear Compartment Lid
Release Connector (Not Used)
Multifunction Relay
RH Parking Lamp and Turn Signal Lamp,
RH Rear Sidemarker Lamp, RH
Stoplamp and Taillamp
RH Low-Beam Headlamp and Turn Signal Switch
RH High-Beam Headlamp Relay
Blower Controller, A/C
Compressor Relay
Heated Rear Window Defogger Relay,
Heated Outside Rearview Mirror
Passenger and Driver Seat Adjuster
Switch, Driver Seat Adjuster
Memory Module
6-59

Downloaded from www.Manualslib.com manuals search engine Relay Box
f I rn II
XI: HORN HI BEAM RH
x
HTD MIRROR lx FLASHER
RR WDO DEFOG
m m
PRK LP

HI BEAM LH ALC
Ip LO BEAM
P PI
DRL
The relay box is located on the lower part of the
instrument panel, to the right
of the steering column.
Relay
I
I1
I11
IV
V
VI
VI1
VI11 IX X
XI
Usage
High-Beam Headlamps I' &IF>
Automatic Level Control
Rear Window Defog, Heated Mirrors
Hazard Warning Flashers
High-Beam Headlamps
I1 (RH)
Horn
Parking Lamps and Turn Signal Lamps
Low-Beam Headlamps
Not Used
Not Used Daytime Running Lamps
6-60