CADILLAC CTS 2005 1.G Owners Manual
Manufacturer: CADILLAC, Model Year: 2005, Model line: CTS, Model: CADILLAC CTS 2005 1.GPages: 432, PDF Size: 2.52 MB
Page 341 of 432
Run-Flat Tires (CTS-V)
If your vehicle has run- at tires, there is no spare tire
and no tire changing equipment. Your vehicle also has
a Tire Pressure Monitor (TPM) which will alert you if
there is a loss of tire pressure in any of the tires. See
Tire Pressure Monitor System (CTS-V) on page 5-65.
{CAUTION:
When the low tire warning light is displayed on
the instrument panel cluster, your vehicle’s
handling capabilities will be reduced during
severe maneuvers. If you drive too fast, you
could lose control of your vehicle. You or
others could be injured. Don’t drive over
55 mph (90 km/h) when the low tire warning
light is displayed. Drive cautiously and check
your tire pressures as soon as you can.If a tire goes at, you won’t need to stop on the side
of the road to change the tire. You can just keep
on driving. The tire can operate effectively with no air
pressure for up to 65 miles (105 km) at speeds up
to 55 mph (90 km/h). The shorter the distance you
drive and the slower the speed, the greater the chance
that the tire will not have to be replaced. When a tire
is lled with air, it provides a cushion between the road
and the wheel. Because you won’t have this cushion
when driving on a de ated run- at tire, try to avoid
potholes that could damage your wheel and require
replacement of it.
Some road hazards can damage a tire beyond repair.
This damage could occur even before you’ve driven on
the tire in a de ated condition. When a tire has been
damaged, or if you’ve driven any distance on a run- at
tire, check with an authorized run- at tire service center
to determine whether the tire can be repaired or should
be replaced. To maintain your vehicle’s run- at feature,
all replacement tires must be self-supporting tires.
5-61
Page 342 of 432
As soon as possible, contact the nearest authorized GM
or run- at servicing facility for inspection and repair or
replacement. To locate the nearest GM or run- at
servicing facility, call Roadside Service. SeeRoadside
Service on page 7-5for details.
{CAUTION:
Run- at tires are constructed differently than
other tires and could explode during improper
service. You or others could be injured or killed
if you attempt to repair, replace, dismount, or
mount a run- at tire. Let only an authorized
run- at service center repair, replace, dismount
and mount run- at tires.
The valve stems on your run- at tires have sensors that
are part of the Tire Pressure Monitor System (TPMS).
These sensors contain batteries which are designed
to last for 10 years under normal driving conditions. See
your dealer if you ever need to have a wheel replaced,
or if the sensors ever need replacement.Notice:Using liquid sealants can damage the
tire valves and tire pressure monitor sensors in your
run- at tires. This damage would not be covered
by warranty. Don’t use liquid sealants in your
run- at tires.
In ation - Tire Pressure
Tires need the correct amount of air pressure to operate
effectively.
Notice:Do not let anyone tell you that
under-in ation or over-in ation is all right. It is not.
If your tires do not have enough air (under-in ation),
you can get the following:
Too much exing
Too much heat
Tire overloading
Premature or irregular wear
Poor handling
Reduced fuel economy
5-62
Page 343 of 432
If your tires have too much air (over-in ation), you
can get the following:
Unusual wear
Poor handling
Rough ride
Needless damage from road hazards
A Tire and Loading Information label is attached to the
vehicle’s center pillar, below the driver’s door latch. This
label lists your vehicle’s original equipment tires and
shows the correct in ation pressures for your tires when
they are cold. The recommended cold tire in ation
pressure, shown on the label, is the minimum amount of
air pressure needed to support your vehicle’s maximum
load carrying capacity.
For additional information regarding how much weight
your vehicle can carry, and an example of the tire
and loading information label, seeLoading Your Vehicle
on page 4-33. How you load your vehicle affects
vehicle handling and ride comfort, never load your
vehicle with more weight than it was designed to carry.
When to Check
Check your tires once a month or more. Do not forget to
check the compact spare tire, if your vehicle has one.
The compact spare should be at 60 psi (420 kPa).
For additional information regarding the compact spare
tire, seeCompact Spare Tire (CTS) on page 5-85.
How to Check
Use a good quality pocket-type gage to check tire
pressure. You can’t tell if your tires are properly in ated
simply by looking at them. Radial tires may look properly
in ated even when they’re underin ated. Check the tire’s
in ation pressure when the tires are cold. Cold means
your vehicle has been sitting for at least three hours or
driven no more than 1 mile (1.6 km).
Remove the valve cap from the tire valve stem. Press
the tire gage rmly onto the valve to get a pressure
measurement. If the cold tire in ation pressure matches
the recommended pressure on the Tire and Loading
Information label, no further adjustment is necessary.
If the in ation pressure is low, add air until you reach the
recommended amount.
If you over ll the tire, release air by pushing on the
metal stem in the center of the tire valve. Re-check the
tire pressure with the tire gage.
Be sure to put the valve caps back on the valve stems.
They help prevent leaks by keeping out dirt and moisture.
5-63
Page 344 of 432
High Speed Operation (CTS-V)
{CAUTION:
Driving at high speeds, 100 mph (160 km/h)
or higher, puts an additional strain on tires.
Sustained high-speed driving causes excessive
heat build up and can cause sudden tire failure.
You could have a crash and you or others
could be killed. Some high-speed rated tires
require in ation pressure adjustment for high
speed operation. When speed limits and road
conditions are such that a vehicle can be driven
at high speeds, make sure the tires are rated
for high speed operation, in excellent condition,
and set to the correct cold tire in ation pressure
for the vehicle load.
The CTS-V performance series has 245/45R18 96W size
tires. These high-performance tires require in ation
pressure adjustment when driving your vehicle at speeds
of 130 mph (209 km/h) or higher with occupants and
cargo weighing 600 lbs. (272 kg) up to 882 lbs. (400 kg).Use the following chart to determine the cold tire
in ation pressure when operating your vehicle under
these conditions.
Tire Size: 245/45R18 96W Recommended Cold
Tire In ation Pressure for High Speed Operation
at 130 mph (209 km/h) or more:
Occupant and
Cargo Weight:
Less than
600 lbs (272 kg)Occupant and
Cargo Weight:
600 lbs (272 kg)
Up to 882 lbs (400 kg)
(Vehicle Capacity
Weight)
Front
TiresRear
TiresFront
TiresRear
Tires
30 psi
(210 kPa)30 psi
(210 kPa)32 psi
(220 kPa)34 psi
(235 kPa)
When you end high-speed driving, return the tires
to the cold in ation pressures shown on the tire and
loading information label. SeeLoading Your Vehicle
on page 4-33.
5-64
Page 345 of 432
Tire Pressure Monitor System
(CTS-V)
The Tire Pressure Monitor (TPM) System uses radio
and sensor technology to check tire pressure levels.
If your vehicle has this feature, sensors are mounted
on each run- at tire and wheel assembly. The TPM
sensors transmit tire pressure readings to a receiver
located in the vehicle once every 60 seconds while the
vehicle is being driven, and once every 60 minutes
if the vehicle is stationary for more than 15 minutes.
Using the Message Center, tire pressure levels can be
viewed by the driver. For additional information about
the message center operation and displays, see
Message Center (CTS-V) on page 3-51.
When a low tire pressure condition is detected, a low
tire warning light, on the instrument panel cluster,
comes on to warn the driver.
When the tire pressure
monitoring system warning
light is lit, one or more
of your tires is signi cantly
under-in ated.You should stop and check your tires as soon as
possible, and in ate them to the proper pressure as
indicated on the vehicle’s tire information placard.
Driving on a signi cantly under-in ated tire causes
the tire to overheat and can lead to tire failure.
Under-in ation also reduces fuel efficiency and tire tread
life, and may affect the vehicle’s handling and stopping
ability. Each tire, should be checked monthly when
cold and set to the recommended in ation pressure as
speci ed in the vehicle placard and owner’s manual.
The Tire and Loading Information label (tire information
placard) is attached, to either, the center pillar near
the driver’s door latch post or on the rear edge of the
driver’s side rear passenger door. The label shows
the size of your vehicle’s original tires and the correct
in ation pressure for your vehicle’s tires when they
are cold. SeeIn ation - Tire Pressure on page 5-62and
Loading Your Vehicle on page 4-33for additional
information.
Your vehicle’s TPM system can alert you about a low
tire pressure condition but it does not replace normal
tire maintenance. SeeTire Inspection and Rotation
on page 5-67andTires on page 5-54.
Notice:Do not use a tire sealant if your vehicle is
equipped with Tire Pressure Monitors. The liquid
sealant can damage the tire pressure monitor
sensors.
5-65
Page 346 of 432
TPM Sensor Identi cation Codes
Each TPM sensor has a unique identi cation code. Any
time you replace one or more of the TPM sensors, the
identi cation codes will need to be matched to the new
tire/wheel position. Each tire/wheel position is matched,
to a sensor, by increasing or decreasing the tire’s air
pressure. The sensors are matched, to the tire/wheel
positions, in the following order: left front (LF), right
front (RF), right rear (RR), and left rear (LR).
You will have one minute to match the rst tire/wheel
position, and ve minutes overall, to match all four
tire/wheel positions. If it takes longer than one minute,
to match the rst tire and wheel, or more than
ve minutes to match all four tire and wheel positions
the matching process stops and you will need to
start over.
The TPM matching process is outlined below:
1. Set the Parking brake.
2. Turn the ignition switch to ON with the engine off.
3. Using the Remote Keyless Entry (RKE) transmitter,
lock and unlock the vehicle’s doors.
4. Press the lock and unlock buttons, at the same
time, on the RKE transmitter. A single horn chirp
will sound, indicating that the TPM system is ready,
and the sensor matching process can begin.
5. Start with the left (driver’s side) front tire.6. Remove the valve cap from the valve stem.
Activate the TPM sensor by increasing or
decreasing the tire’s air pressure for ve seconds,
or until a horn chirp sounds. The horn chirp,
which may take up to 30 seconds, con rms that the
sensor identi cation code has been matched to
this tire position. To decrease the tire’s air-pressure
use the pointy end of the valve cap, a pencil-style
air pressure gage or a key.
7. Proceed to the right (passenger’s side) front tire,
and repeat the procedure in Step 6.
8. Proceed to the right (passenger’s side) rear tire,
and repeat the procedure in Step 6.
9. Proceed to the left (driver’s side) rear tire, and
repeat the procedure in Step 6.
10. After hearing the con rming double horn chirp, for
the left rear tire, exit the matching process by
turning the ignition switch to OFF.
11. Set all four tires to the recommended air pressure
level as indicated on the tire and loading information
label.
12. Put the valve caps back on the valve stems.
The TPM system will not function properly if one or
more of the TPM sensors are missing or inoperable.
If the system detects a missing or inoperable sensor
an error message of several dashes–––will be
shown on the message center display.
5-66
Page 347 of 432
If you have replaced a tire/wheel assembly without
transferring the TPM sensors, the error message will be
displayed. Once you re-install the TPM sensors, the
error message should go off. See your GM dealer
for service if all TPM sensors are installed and the error
message comes on and stays on.
The TPM system operates on a radio frequency subject
to Federal Communications Commission (FCC) Rules
and with Industry and Science Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-210 of Industry Canada.
Operation is subject to the following two conditions:
1. this device may not cause interference, and
2. this device must accept any interference received,
including interference that may cause undesired
operation of the device.
Changes or modi cations to this system by other than
an authorized service facility could void authorization to
use this equipment.Tire Inspection and Rotation
Tires should be rotated every 5,000 to 8,000 miles
(8 000 to 13 000 km).
Any time you notice unusual wear, rotate your tires as
soon as possible and check wheel alignment. Also
check for damaged tires or wheels. SeeWhen It Is Time
for New Tires on page 5-69andWheel Replacement
on page 5-72for more information.
The purpose of regular rotation is to achieve more
uniform wear for all tires on the vehicle. The rst rotation
is the most important. SeeScheduled Maintenance
on page 6-4.
When rotating your tires, always use the correct rotation
pattern shown here.
5-67
Page 348 of 432
If your vehicle has a compact spare tire, do not include
it in the tire rotation.
After the tires have been rotated, adjust the front and
rear in ation pressures as shown on the Tire and
Loading Information label. SeeLoading Your Vehicle
on page 4-33, for an example of the tire and loading
information label and its location on your vehicle.
If your vehicle has run- at tires, the Tire Pressure
Monitor (TPM) system will need to have the sensors
reset after a tire rotation is performed. A special tool is
needed to reset the sensor identi cation codes. See
your dealer for service.
Make certain that all wheel nuts are properly tightened.
See “Wheel Nut Torque” underCapacities and
Speci cations on page 5-107.
{CAUTION:
Rust or dirt on a wheel, or on the parts to
which it is fastened, can make wheel nuts
become loose after a time. The wheel could
come off and cause an accident. When you
change a wheel, remove any rust or dirt from
places where the wheel attaches to the vehicle.
In an emergency, you can use a cloth or a
paper towel to do this; but be sure to use a
scraper or wire brush later, if needed, to get
all the rust or dirt off. SeeChanging a Flat
Tire (CTS) on page 5-76.
5-68
Page 349 of 432
When It Is Time for New Tires
One way to tell when it’s
time for new tires is to
check the treadwear
indicators, which will
appear when your tires
have only 1/16 inch
(1.6 mm) or less of
tread remaining.
You need a new tire if any of the following statements
are true:
You can see the indicators at three or more places
around the tire.
You can see cord or fabric showing through the
tire’s rubber.
The tread or sidewall is cracked, cut or snagged
deep enough to show cord or fabric.
The tire has a bump, bulge or split.
The tire has a puncture, cut or other damage that
can’t be repaired well because of the size or
location of the damage.
Buying New Tires
To nd out what kind and size of tires your vehicle
needs, look at the tire and loading information label. For
more information about this label and its location on
your vehicle, seeLoading Your Vehicle on page 4-33.
The tires installed on your vehicle when it was new had a
Tire Performance Criteria Speci cation (TPC Spec)
number on each tire’s sidewall. When you get new tires,
GM recommends that you get tires with that same TPC
Spec number. That way your vehicle will continue to
have tires that are designed to give proper endurance,
handling, speed rating, load range, traction, ride, tire
pressure monitoring system performance and other
things during normal service on your vehicle. If your
tires have an all-season tread design, the TPC number
will be followed by an “MS” (for mud and snow).
Whenever you replace your tires with those not having
a TPC Spec number, make sure they are the same
size, load range, speed rating and construction
type (bias, bias-belted or radial) as your original tires.
5-69
Page 350 of 432
Winter tires with the same speed rating as your original
equipment tires may not be available for H, V, W,
and ZR speed rated tires. If you choose snow tires with
a lower speed rating, never exceed the tire’s maximum
speed capability.
If you replace your vehicle’s tires with those not having
a TPC Spec number, the tire pressure monitoring
system may give an inaccurate low pressure warning.
Non-TPC Spec tires may give a low pressure warning
that is higher or lower than the proper warning level you
would get with TPC Spec numbered tires.
{CAUTION:
Mixing tires could cause you to lose control
while driving. If you mix tires of different sizes
or types (radial and bias-belted tires), the
vehicle may not handle properly, and you
could have a crash. Using tires of different
sizes may also cause damage to your vehicle.
Be sure to use the same size and type tires on
all wheels. It’s all right to drive with your
compact spare temporarily, it was developed
for use on your vehicle. SeeCompact Spare
Tire (CTS) on page 5-85.
{CAUTION:
If you use bias-ply tires on your vehicle, the
wheel rim anges could develop cracks after
many miles of driving. A tire and/or wheel
could fail suddenly, causing a crash. Use only
radial-ply tires with the wheels on your vehicle.
Uniform Tire Quality Grading
Quality grades can be found where applicable on the
tire sidewall between tread shoulder and maximum
section width. For example:
Treadwear 200 Traction AA Temperature A
The following information relates to the system
developed by the United States National Highway
Traffic Safety Administration, which grades tires by
treadwear, traction and temperature performance.
(This applies only to vehicles sold in the United States.)
5-70