door lock CADILLAC DEVILLE 1997 7.G User Guide

Downloaded from www.Manualslib.com manuals search engine This device complies with Part 15 of the FCC Rules.
Operation
is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
This device complies with
RSS-210 of Industry and
Science Canada. Operation is subject to the following
two conditions:
(1) this device may not cause
interference, and
(2) this device must accept any
interference received, including interference that may
cause undesired operation of the device.
The range of this system is about
10 feet (3 m). At times
you
may notice a decrease in range. This is normal for
any remote lock control system. If the transmitter does
not work
or if you have to stand closer to your vehicle
for the transmitter to work, try this:
Check to determine if battery replacement is
necessary. See the instructions that follow.
Check the distance. You may be too far from your
vehicle. You may need to stand closer during rainy
or snowy weather.
Check the location. Other vehicles or objects may be
blocking the signal. Take a few steps
to the left or
right, hold the transmitter higher, and try again.
If you’re still having trouble, see your Cadillac
dealer
or a qualified technician for service. Changes
or modifications to this system
by other than an
authorized service facility could void authorization to
use this equipment.
Operation
* When you press this symbol to unlock the
driver’s door, the parking lamps on your vehicle will
blink twice. (You can program your vehicle
so the
parking lamps will not flash. For more information, see
“Remote Confirmation” later in this section.) Pressing it
again within five seconds will unlock the other doors.
Pressing this button will also disarm the optional
theft-deterrent system and turn
on the interior lamps
at night.
8 When you press this symbol to lock the doors, the
parking lamps will blink once. (You can program your
vehicle
so the parking lamps will not flash. For more
information,
see “Remote Confirmation” later
in this section.) This also
arms the optional
theft-deterrent system.
Press this symbol to open the trunk.
Press this button to open the fuel door.

Downloaded from www.Manualslib.com manuals search engine The RKE transmitter can also be used to recall the
memory settings for up to two drivers. For more
information, see “Memory Seat and Mirrors” in
the Index.
Note that pressing the transmitter buttons numerous times (approximately
500 times) out of the vehicle’s operating
range may cause the transmitter not to work. Replacing
the battery and pressing the transmitter buttons
10 or
more times out of range will also cause
the transmitter
not to work. To reset the transmitter, you must be within
the vehicle’s operating range. Press and hold the trunk
button, and within one second, press and hold the lock
button. Continue to hold both buttons for approximately
three seconds. See your Cadillac dealer for service if your
transmitter still doesn’t work properly.
RKE Personalization Features
Remote Confiimation (If Equipped)
Before you select features, be sure that the number on
the back of the RKE transmitter matches the driver
preferred.
You can confirm the correct driver by placing
the key in the LOCK position and pressing unlock on
the
RKE transmitter.
This personalization feature allows the driver to program
the parking lamps to blink or to remain
off when the lock or unlock buttons
on the RKE transmitter are pressed.
Press the TRIP SET
(TRIP RESET) button to answer
“yes,” press
the RESET (INFO RESET) button to indicate
“no” or press the INFORMATION
(INFO) button to
“skip” to the next personalization feature.
To begin programming, the ignition must be in the RUN
position. Press and hold the INFORMATION (INFO)
and RESET (INFO RESET) buttons at the same time.
The first message to appear refers to the programmable
automatic door locks. To skip this prompt, press the
INFORMATION (INFO) button.
When
REMOTE FLASH LIGHTS appears on the DIC
display, press the yes button
to program the parking
lamps to blink once when the lock button on the
RKE
transmitter is pressed and to blink twice when the
unlock button is pressed.
If you don’t want the parking
lamps to blink when using the
RKE transmitter, press
the
no button.
FEATURE
ON will display if REMOTE FLASH
LIGHTS was selected and FEATURE OFF will show if
you answer no.
For
a list of the other personalization features available,
see “Memory and Personalization Features” later in
this section.

Downloaded from www.Manualslib.com manuals search engine Exterior Lighting (If Equipped)
This personalization feature enables the driver to
program the exterior lamps to turn on for 20 seconds or
to remain off when using the RKE transmitter to unlock
your vehicle.
If exterior lighting is selected, the parking lamps,
taillamps, sidemarker lamps, license plate lamps,
low-beam headlamps, etc. will turn on for about
20 seconds or until the ignition key is turned to RUN.
Check the back of the RKE transmitter to verify
that the
correct driver
is selected before you start programming.
To begin programming, press the INFORMATION
(INFO) and RESET (INFO RESET) buttons at the same
time for about two seconds. Exterior lighting is the third
feature to display. Press the INFORMATION (INFO)
button to “skip” past the first two features
-- DOOR
LOCKS IN GEAR and REMOTE FLASH LIGHTS.
When EXT LIGHTS AT UNLOCK appears, a “yes” or
“no” response is required. Press the TRIP SET (TRIP
RESET) button to answer yes or press the RESET
(INFO RESET) button to indicate a no response.
FEATURE ON displays when a yes response
is made
and FEATURE OFF shows after a no response.
For a list
of the other personalization features available, see
“Memory and Personalization Features” later in
this section.
Remote Recall Memory quipped)
Your vehicle may have memory personalization. If it
does,
REMOTE RECALL MEMORY will be the fourth
personalization feature to display
on the DIC system.
Memory settings that have been previously programmed
(HVAC settings, radio preset settings, exterior lighting
choices, remote confirmation choices and programmable automatic door lock choices) can be recalled either by
using the
RKE transmitter or by placing the key in your
vehicle’s ignition.
To begin programming, check the back of the RISE
transmitter to verify that the correct driver is selected.
Press the INFORMATION
(INFO) and RESET (INFO
RESET) buttons at
the same time for about two seconds.
As mentioned, memory recall is the fourth feature to
appear. To “skip” past the first three personalization
features, press the INFORMATION (INFO) button.
When REMOTE RECALL MEMORY appears, the driver is able to recall memory settings when the unlock
button on the RKE transmitter is pressed with the
ignition in LOCK. Press the TRIP SET (TRIP RESET)
button to select or press the RESET (INFO RESET)
button to answer no
and to continue on to the next
prompt. (FEATURE ON displays when a yes response
is made and FEATURE
OFF shows when a no response
is made.)

Downloaded from www.Manualslib.com manuals search engine /-
B
A. Trunk Lid
B. Lever
If for some reason the trunk lid will not close, it may be
because the trunk pull-down unit was accidentally
bumped. Even though the trunk lid remains open, the motor from the pull-down unit has already cycled down.
If this happens, press the lever on the trunk lid. The
pull-down unit motor will reset itself allowing the trunk lid to close when lowered.
Theft
Vehicle theft is big business, especially in some cities.
Although your Cadillac
has a number of theft-deterrent
features,
we know that nothing we put on it can make
it impossible to steal. However, there are ways you
can help.
Key in the Ignition
If you leave your vehicle with the keys inside, it’s an
easy target for joy riders or professional thieves
-- so
don’t do it.
When you park your Cadillac and open the driver’s door, you’ll hear a chime reminding you to remove your key
from the ignition and take it with you. Always do this.
Your steering wheel will be locked, and so will your
ignition and transaxle.
And remember to lock the doors.
Parking at Night
Park in a lighted spot, close all windows and lock your
vehicle. Remember to keep your valuables out
of sight.
Put them in a storage area, or take them with you.
Parking Lots
If you park in a lot where someone will be watching
your vehicle, it’s best to lock
it up and take your keys.
2-16

Downloaded from www.Manualslib.com manuals search engine But what if you have to leave your ignition key? What if
you have to leave something valuable in your vehicle?
Put your valuables in a storage area, like your trunk
Lock the glove box.
Lock all the doors except the driver’s.
Then take the door key and remote keyless entry
or
glove box.
transmitter with you.
Theft-Deterrent System (If Equipped)
SECURITY
If the ignition is off and
any door is open, the
SECURITY light will flash,
reminding you to activate
the system (the light will
also flash if the battery
has been disconnected
and reconnected).
1. Open the door.
2. Lock the door using the power door lock or the RKE
system. The
SECURITY light should come on and
stay on.
3. Close all the doors. The SECURITY light should go
off within approximately 30 seconds.
The horn will sound and the lamps
will flash for about
30 seconds when the door or trunk is opened without the
key or RKE system. The horn also sounds if the locks
are damaged.
Remember, the theft-deterrent system won’t activate if
you lock the doors with a key or
use the manual door
lock. It activates only
if you use a power door lock
switch or the RKE system.
To avoid activating the alarm by accident:
The vehicle should be locked with the door key after
the doors are closed if you don’t want to activate the
theft-deterrent system.
Always unlock a door with a key or use the RKE
system. (Pressing the unlock button on the RKE
transmitter disables the theft-deterrent system.)
Unlocking a door any other way will activate the
alarm. Cycling
the ignition without disarming the
theft-deterrent system will also activate the alarm.
If you activate the alarm by accident, unlock any door
with your key. You can also turn off the alarm by using
the RKE system. The alarm won’t stop
if you try to
unlock a door any other way.
2-17

Downloaded from www.Manualslib.com manuals search engine Testing the Alarm
1. From inside the vehicle, roll down the window, then
get out of the vehicle, keeping the door open.
2. From outside of the vehicle, with the door open, lock
the vehicle using the power door lock or the RKE system and close the door. Wait
30 seconds until the
SECURITY lamp goes off.
3. Reach in and unlock the door using the manual lock
and open the door. The horn will sound and the
headlamps will flash.
If the alarm does not sound when it should, check to see
if the horn works. The horn fuse may be blown. To
replace the fuse, see “Fuses and Circuit Breakers” in the\

Index.
If the fuse does not need to be replaced, you may
need to have your Cadillac serviced.
To reduce the possibility of theft, always activate the
theft-deterrent system when leaving your vehicle.
Security Override
Pressing the VALET button
located inside the glove box
will disable the use
of the
power
trunk, fuel door and
garage door openers.
Pressing this button again will make these features
reusable. Locking the glove box with the door
key will also help to secure
your vehicle.
Note that the RKE transmitter can’t be used to open the
trunk or fuel door if the VALET button is pressed in.

Downloaded from www.Manualslib.com manuals search engine C
With the ignition key in the ignition switch, you can turn
the switch to five different positions:
ACCESSORY (A): This position lets you use things
like the radio and the windshield wipers when the
engine is off.
To get into ACCESSORY, push in the key
and turn it toward you. The steering wheel will remain
locked, just as it was before you inserted the key.
LOCK (B): Before you put the key in, the ignition will
be in the LOCK position. This
is the only position in
which you can remove the key. This position locks the
ignition, steering wheel and transaxle. It’s a
theft-deterrent feature.
OFF (C): This position lets you turn off the engine but
still turn the steering wheel. It doesn’t lock the steering
wheel like
LOCK. Use OFF if you must have your
vehicle in motion while the engine is off (for example, if
your vehicle is being pushed).
RUN (D): This is the position for driving.
START (E): This starts the engine.
Retained Accessory Power (RAP)
The following accessories on your Cadillac may be used
for up to
10 minutes after the ignition key is turned from
RUN to
OFF:
Radio
Power Windows
0 Astroroof
Power to these accessories stops after
10 minutes or
if any door is opened.
If you want power for another
10 minutes, turn the ignition key to RUN and then back
to
OFF.

Downloaded from www.Manualslib.com manuals search engine Shifting Out of PARK (P) .ng Over Things That Burn
Your Cadillac has a Brake-Transaxle Shift Interlock .- . .,..I ..a’.. . ..*.
(BTSI). You have to fully apply your regular brakes
before you can shift from PARK (P) when the ignition is
in the RUN position. See “Automatic Transaxle” in
the Index.
.... ,.., ’. i
If you cannot shift out of PARK (P), ease pressure on
the shift lever
-- push the shift lever all the way into
PARK
(P) and also release the shift lever button on floor
shift models as you maintain brake application. Then
move the shift lever into the gear you want. (Press the
shift lever button before moving the shift lever.) If you
ever hold the brake pedal down but still can’t shift out of
PARK
(P), try this:
I. Turn the key to OFF. Open and close the driver’s
door
to turn off the RAP feature.
2. Apply and hold the brake until the end of Step 4.
3. Shift to NEUTRAL (N).
m
r
4. Start the vehicle and then shift to the drive gear
you want.
5. Have the vehicle fixed as soon as you can.
Things that can burn coula touch hot exhaust
parts under your vehicle and ignite. Don’t park
over papers, leaves, dry grass or other things that
can burn.
2-33

Downloaded from www.Manualslib.com manuals search engine To begin programming, press the INFORMATION
(INFO) and RESET (INFO RESET) buttons at the same
time for about two seconds. The first message to appear
is DOORS LOCK
IN GEAR. Press the INFORMATION
(INFO) button after this prompt is displayed until
STORAGE MODE prompt appears on the DIC. Press
the
TRIP SET (TRIP RESET) button to answer “yes” or
press the RESET
(INFO RESET) button to indicate a
“no” response.
FEATURE
ON appears when a yes response is made
and FEATURE
OFF shows when a no response is made.
Since this is the last personalization feature available, a
yes or no response will end out of the
DIC display.
Once the battery guard has been programmed, your
vehicle will enter the storage mode about
20 minutes
after the ignition key has been turned off. The RKE will
also be disabled at
this point. The RKE will reactivate
when a door or the
trunk is opened, however, if your
vehicle is left inactive for another
20 minutes, the RKE
will re-enter the storage mode.
Your vehicle will stay in the storage mode until the
ignition key is turned out of LOCK. The system will
“wake-up” when the door key is inserted into the door,
however, your vehicle will remain in the storage mode.
The ignition must be out of LOCK before the battery
guard is disabled.
Mirrors
Inside Daymight Manual Rearview Mirror
When you are sitting in a comfortable driving position,
adjust the mirror
so you can see clearly behind your car.
Grip the
mirror in the center to move it up or down and
side to side. The day-night adjustment allows you to
adjust the mirror to avoid glare from the headlamps
behind you. Pull the tab forward for daytime use. Push it
back for night use.

Downloaded from www.Manualslib.com manuals search engine Driver’s Outside Auto-Dimming Rearview
Mirror
(If Equipped)
Only the driver’s side outside mirror will adjust for
the glare of headlamps behind you. This feature is
controlled
by the on and off settings on the
electrochromic mirror. See “Electrochromic
Daymight Rearview Mirror” earlier in this section.
Convex Outside Mirror
Your passenger’s side mirror is convex. A convex
mirror’s surface
is curved so you can see more from the
driver’s seat.
:ON:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If
you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder before
changing lanes.
Storage Compartments
Glove Box
The glove box is located in front of the passenger’s seat.
To lock the glove box door, insert the oval key into the
lock cylinder and turn it clockwise. Turn the key
counterclockwise to unlock the door.
Map Pocket
The maphtorage pockets are located on each front door as
well as on the passenger’s and driver’s front seatbacks.
Front Storage Armrest
(DeVille and DeVille d’Elegance Only)
The front storage area comes with a coinholder, a
storage compartment for CDs or tapes and a dual
cupholder that unfolds for use.
2-59
._