display CADILLAC DEVILLE 1997 7.G Owner's Guide

Downloaded from www.Manualslib.com manuals search engine VERY LOW REFRIGERANT A/C COMPRESSOR
OFF - 12: This message means that the air conditioning
system detects
a refrigerant level that is low enough to
cause damage to the air conditioning compressor.
To avoid damage, the air conditioning compressor
automatically turns off and the Electronic Climate
Control will automatically switch from AUTO to AC
and remain there. Have the air conditioning system
serviced if this message appears.
Continuous Variable - Real Time Damping
(CV-RTD) (DeVille Concours Only)
The CV-RTD automatically adjusts the ride of your
vehicle. Automatic ride control is achieved through
a
computer controller used to control and monitor the
suspension system. The computer controller receives
inputs from various sensors to determine the proper
system response. If the computer controller detects a
problem within the system, the DIC will display a
SERVICE RIDE CONTROL message. If this
message appears, have your vehicle serviced at your Cadillac dealership.
Oil Life Indicator
This feature lets you know when to change the engine
oil. It's based on the engine oil temperatures and
your driving patterns.
To see the display, press the
INFORMATION (INFO) button until
XX OIL LIFE
LEFT appears.
If you see 99% OIL LIFE LEFT,
99 percent of your current oil life remains.
2-96

Downloaded from www.Manualslib.com manuals search engine The DIC may display a CHECK OIL LEVEL message.
Always keep a written record of the mileage and date
when you changed your oil. For more information, see
the Cadillac Maintenance Schedule booklet. If you see
CHECK
OIL LEVEL, it means that you have less than
10 percent of the oil life left and you should consider
changing your engine oil. If you see CHANGE
ENGINE OIL, it means the oil life is gone and you
should change the oil right away.
The system should indicate changing the oil between
3,000 miles (5 000 km) and 7,500 miles (12 500 km).
It may indicate changing the oil before 3,000 miles
(5 000 km) depending on your driving habits. If the vehicle has been driven
7,500 miles (12 500 km), it will
indicate to change the oil.
If you drive in a dusty area,
you should change your oil every
3,000 miles (5 000
km) or three months (whichever comes first) unless the
display indicates changing it sooner. The system doesn’t
check
how much oil you have, so you’ll still have to
check for that.
To see how, see “Engine Oil” in
the Index.
When new oil
is added, you’ll need to reset the system.
To reset, display the Oil Life Indicator by pressing the
INFORMATION (INFO) button. Then press and hold
the RESET button until the display shows 100% OIL
LIFE LEFT.
2-97
. ~

Downloaded from www.Manualslib.com manuals search engine Driver’s Side Temperature Button
The red and blue temperature buttons adjust the air
temperature coming through the system. Press the blue
button for a cooler setting or the red button for a
warmer setting.
Passenger’s Side Temperature Knob
With this feature, the right front passenger can control
the temperature of air for hisher own zone. The
passenger can select a four degree warmer or cooler
temperature from the driver’s setting.
To turn the system on, press the knob on the passenger’s
side armrest. Rotate the knob clockwise to increase the
temperature and turn counterclockwise to decrease the
temperature. Press the knob again
to turn the system off.
Outside Temperature Display
The outside temperature is always displayed when your
vehicle is running. You can change it from Fahrenheit to
Celsius by pressing
the ENG/MET (Englishlmetric)
button on the Driver Information Center (DIC).
The outside temperature sensor is located near the front
grille. The sensor can be affected by road or engine heat
during idling, slow driving
or when the engine is first
started after a short trip. In order to ensure proper
automatic climate control operation, the outside air temperature
display may not update as quickly as
expected. This is
to allow the air surrounding the outside
temperature sensor
to be as close to the actual outside
conditions as possible. This is determined by how much
time has elapsed since the vehicle has been turned
off
and by vehicle speed.
Mode Controls
The AUTOBCON button automatically controls the
direction of air delivery for air conditioning and non-air
conditioning modes.
Automatic Operation
When the system is set for automatic operation, sensors
will control the air delivery mode. Air will come from
the floor, middle or windshield outlets. The fan speed
will vary as the system maintains the selected
temperature setting.
Be careful not to put anything over the solar sensor
located in the middle of the instrument panel near the
windshield. This sensor is used by the automatic system
to regulate temperature.

Downloaded from www.Manualslib.com manuals search engine Manual Operation
RECIRCULATION: Press this button to limit the
amount of fresh air entering your vehicle. This is helpful
when you are trying to cool the air quickly or limit odors
entering your vehicle. In the AUTO mode, the system
will use recirculation
as necessary to cool the air.
Pressing the recirculation button will change the
operation to
a manual mode and the air will recirculate
non-stop. Press this button again to turn
off the
recirculation feature.
If you notice the windows fogging, press the
recirculation button to exit the recirculation mode.
OFF: Press this button to turn the system off. Fresh air
will continue to flow through the vehicle, and the
system will try to maintain the previously set
temperature. The outside temperature will show
in the
display when the system is off.
DEFOG: Press this button to divide the air between the
windshield and the heater outlets. This is useful when
fog appears on the windshield or side glass due to
sudden rain or snowy conditions.
AUTOECON: Press this button to switch between
AUTO and ECON. The ECON setting attempts to keep air
at a selected temperature, however, it does not remove
humidity from the
air. Use this setting in cold or cool weather to save fuel. The AUTO setting is used when it’s
warm outside and you need to cool the air in order to
maintain a selected temperature and blower speed.
# FAN SPEEDS: Press the button with the fan
symbol on it until AUTO is displayed
on the screen.
At this setting, the fan speed
is automatically controlled.
If it is cold outside, the blower may not run in the
maximum high fan speed right away. The system checks
the temperature
of the engine coolant to assure it is
warm enough to provide heat. When the engine coolant
is
warm, the controller allows the fan to gradually
increase to a higher speed. This prevents cold air from
blowing into the passenger compartment. If you want
the blower fan at a high speed, press the up arrow button
until you see HI on the display. If you want the fan
speed to be automatic, but you like the fan speed to be
higher than the AUTO setting, press the fan symbol
button until
HI AUTO is shown on the display. If you
want the blower
fan at a low speed, press the down
arrow button until
LO is shown on the display. If you
want the fan speed to run lower than the
AUTO
setting, press the button until AUTO LO is shown
on the display.
9 DEFROST Press this button to quickly remove
fog or frost from the windshield. This setting sends most
of the airflow to the windshield with only a small
amount to the floor outlets.
AI

Downloaded from www.Manualslib.com manuals search engine Driver’s Side Temperature Knob
The TEMP/AUTO knob adjusts the air temperature coming
through the system.
Turn the TEMP/AUTO knob clockwise
to increase the temperature and counterclockwise to
decrease the temperature. Press the
TEMWAUTO knob to
put the system
in the automatic mode.
Passenger’s Side Temperature Button
With this feature, the right front passenger can control
the temperature of air for hisher own zone. The
passenger can select a four degree warmer or cooler
temperature from the driver’s setting.
To turn the system on, press the PASS/TEMP button
located below the radio. Press the up arrow to increase
the temperature and press the down arrow to decrease
the climate setting. Pressing the OFF button will turn
off
the dual-zone function.
Outside Temperature Display
The outside temperature is always displayed when your
vehicle is running. You can change it from Fahrenheit to
Celsius by pressing the ENGMET (Englishlmetric) on
the Driver Information Center (DIC).
The outside temperature sensor is located near the front
grille. The sensor can be affected by road or engine heat
during idling, slow driving or when the engine is first started after a short trip. In order
to ensure proper
automatic climate control operation, the outside air
temperature display may not update as quickly as
expected. This is to allow the air surrounding the outside
temperature sensor to be as close to the actual outside
conditions
as possible. This is determined by how much
time has elapsed since the vehicle has been turned off
and by vehicle speed.
Mode Button
Press this button to deliver air through the floor, middle
or windshield outlets. The system will stay in the
selected mode until the MODE button is pushed again.
Press the up
or down arrow to cycle through the
available modes.
Automatic Operation
When the system is set for automatic operation, sensors
will control the air delivery mode. Air will come from
the floor, middle or windshield outlets. The fan speed
will vary as the system maintains the selected
temperature setting.
Be careful not to put anything over the solar sensor
located in the middle of the instrument panel near the
windshield. This sensor is used by the automatic system
to regulate temperature.

Downloaded from www.Manualslib.com manuals search engine Manual -= mation
You may manually adjust the air delivery mode or
fan speed.
he
fl AC: This setting directs airflow through the
middle instrument panel outlets.
he
BI-LEVEL: This setting directs air into your
vehicle in two ways. Cool air is directed to the upper
portion of your body through the four instrument panel
outlets while warmed air
is directed to the floor.
'# HEATERDEFROST: This setting directs air to
the floor outlets and toward the windshield.
lfl HEATER: This setting directs warmed air
through the floor outlets. Some warm air is diverted to
the windshield to minimize fogging.
DEFROST Press this button to quickly remove
fog or frost from the windshield.
This setting sends most
of the airflow to the windshield with only a small
amount to
the floor outlets.
we
0
# FAN SPEEDS: Press the button with the fan symbol
on it until AUTO is displayed on the screen. At
this
setting, the fan speed is automatically controlled. If it is
cold outside, the blower may not run in the maximum
high fan speed right away. The system checks the
temperature of the engine coolant to assure it is warm
enough to provide heat. When the engine coolant is
warm, the controller allows the fan to gradually increase
to a higher speed.
This prevents cold air from blowing
into the passenger compartment. If you want the blower
fan at a high speed, press the up arrow button until you see HI on the display. If you want the fan speed to be
automatic, but
you like the fan speed to be higher than
the AUTO setting, press the fan symbol button until HI
AUTO is shown on the display. If you want the blower
fan at a low speed, press the down arrow button until LO
is shown on the display. If you want the fan speed to run
lower than the AUTO setting, press the button until
LO
AUTO is shown on the display.

Downloaded from www.Manualslib.com manuals search engine OFF: Press this button to turn the system off. Fresh air
will continue to flow through the vehicle, and the system will try to maintain the previously set
temperature. The outside temperature will show on the
display when the system is
OFF.
AC: Press this button to turn the air conditioning on and
off. The system will cool and dehumidify the air inside
the vehicle. In the
AUTO mode, the display will show
that
AC is active, but the air conditioning compressor
only operates when the system determines it is needed.
RECIRCULATION: Press this button to limit the
amount of fresh
air entering your vehicle. This is helpful
when you are
trying to cool the air quickly or limit odors
entering your vehicle.
In the AUTO mode, the system will
use recirculation as necessary to cool the air. Pressing the
recirculation button will change the operation to a manual mode and the
air will recirculate non-stop. Press this
button again to
turn off the recirculation feature.
If you notice the windows fogging, press the
recirculation button to exit the recirculation mode.
Air Conditioning
On hot days, open the windows long enough to let hot
inside air escape. This reduces the time it takes for your
vehicle to cool down. Then keep your windows closed
for the air conditioner
to work its best.
With the digital cluster climate control panel, press the
AUTOECON button to assist in cooling air and in
maintaining proper airflow. Adjust the temperature to a
comfortable setting by pressing the blue button to cool
your vehicle and pressing the red button to
warm your
vehicle. Press the fan button arrows up
or down to adjust
the fan speed.
If you have the analog cluster climate control panel,
press the
AC button or the TEMP/AUTO knob to turn
the system on and then select the proper
MODE to direct
airflow. The system will cool and dehumidify the air
inside the vehicle. Also while in the AUTO mode, the
system will use recirculation as necessary to cool the air.
You may also need to adjust the interior temperature and
the fan speed as needed.
When the
air conditioner is on, you may sometimes notice
slight changes in your vehicle’s engine speed and power.
This is normal because the system is designed to cycle the
compressor
on and off to keep the desired temperature.

Downloaded from www.Manualslib.com manuals search engine Setting the Clo L
Press and hold HR or MN until the time display begins
to change. Release the button as you get close to the
correct time. The time may be set anytime the clock is
displayed. There is a two-second delay before the clock
goes into time-set mode.
AM-FM Stereo with Cassette Tape Player
and Optional Compact Disc Player
Playing the Radio
PWRNOL:
Press this knob lightly to release it from its
stored position. The system will turn on. Press the knob
again
to turn the system off. To increase volume, turn
the knob clockwise. Turn it counterclockwise to
decrease volume. The volume level will appear on
the display.
DSPL: Press this button to display the station
being played.
Finding a Station
BAND:
Press this button to select AM, FM1 or FM2
and preset stations.
SEEK-TUNE: Press and release this button to seek to
the next higher or lower radio station. Pressing and
holding this button
until a chime sounds puts the radio
in
a tune mode. In this mode, higher or lower radio
stations
are advanced to in small increments until the
SEEK-TUNE button is released (larger increments if
held longer). Tuning stops when you release this button.
If you press and hold the SEEK-TUNE button again
within five seconds
of being in the tune mode, tuning
will continue. Waiting longer than five seconds places
the radio back in the seek mode.
For information
on the compact disc player, see “Trunk
Mounted
CD Changer” later in this section.
3-15

Downloaded from www.Manualslib.com manuals search engine SCAN: Press this button and SCAN will appear on the
display. Use
SCAN to listen to stations for a few
seconds. The radio will go to a station, stop for a few
seconds, then go on to the next station. Press this button
again to stop scanning.
PUSHBUTTONS: The six numbered pushbuttons let
you return to your favorite stations. You can set up to
18 stations (six AM, six FM1 and six FM2). Just:
1. Turn the radio on.
2. Press BAND to select AM, FMl or FM2.
3. Tune in the desired station.
4. Press and hold one of the six numbered buttons until
you hear a chime. The sound will mute. When it
returns, release the button. Whenever you press that
numbered button, the station you set will return.
5. Repeat the steps for each pushbutton.
PRESET SCAN: Press and hold SCAN for two to three
seconds
until PRESET SCAN appears on the display to
listen to each
of your preset stations for a few seconds
(factory presets which have not been reprogrammed with
your stations will
be ignored). The radio will go to the frrst
preset station stored on your pushbuttons, stop for a few seconds, then go on to the next preset station. Press
SCAN
again to stop scanning. If a preset station has weak
reception, the radio will not stop at the preset station.
Setting the Tone
BASS:
Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise to
decrease bass.
TREB: Press this knob lightly so it extends. Turn the
knob clockwise to increase and counterclockwise to
decrease treble.
If a station is weak or noisy, you may
want to decrease the treble.
Push these knobs back into their stored positions when
you’re not using them.
Adjusting the Speakers
BAL:
Press this knob lightly so it extends. Turn the
knob clockwise to adjust sound to the’right speakers and
counterclockwise for the left speakers. The middle
position balances the sound between the speakers.
FADE: Press this knob lightly so it extends. Turn the
knob clockwise to adjust the sound to the front speakers
and counterclockwise for the rear speakers. The middle
position balances the sound between the speakers.
Push these knobs back into their stored positions when you’re not using them.

Downloaded from www.Manualslib.com manuals search engine Playing a Cassette Tape
With the radio on, insert a cassette tape. The tape will
begin playing as soon as it is inserted.
While the tape is playing, use the VOL, FADE, BAL,
BASS and TREB controls just as you do for the radio.
Other controls may have different functions when a tape
is inserted. The display will show TAPE with an arrow
to indicate which side of the tape
is playing. PLAY will
appear on the display temporarily when a tape is
playing. The display will then revert back to showing
the time.
If an error occurs while trying to play a cassette tape, it
could be that:
The cassette tape is tight and the cassette player
cannot turn the hubs
of the tape. Hold the cassette
tape with the open end down and try turning the right
hub counterclockwise with a pencil. Flip the tape
over and repeat. If the hubs do not turn easily, your
cassette tape may be damaged and should not be
used in the player. Try a new tape to be sure your
player is working properly.
The cassette tape is broken. (Check to see if your
tape is broken. Try a new tape.)
REV: Press the left arrow to reverse the tape rapidly.
Press it again to return to playing speed. The radio will
play while the tape reverses and
REV will appear on the
display. You may use your station pushbuttons to tune to
another radio station while in
REV mode.
FF: Press the right arrow to fast forward to another part
of the tape. Press it again to return to playing speed. The
radio will play while the tape advances and FF will
appear on the display. You may use your station
pushbuttons
to tune to another radio station while in
FF mode.
SEEK-TUNE: Press the right arrow to seek to the next
selection on the tape. Press the left arrow to search for
the previous selection
on the tape (REP will appear on
the display). Your tape must have at least three seconds
of silence between each selection for SEEK-TUNE to
work. The sound will
mute while seeking.
SCAN: Press this button. SCAN FF will appear on the
display until the next selection is found and then SCAN
PLAY will appear on the display. Use SCAN to listen to
selections for a few seconds. The tape will go to
a
selection, stop for a few seconds, then go on to the next
selection. Press this button again to stop scanning.
SIDE: Press this button to change the side of the tape
that is playing. (PLAY shows on the display.)
3-17