CADILLAC DTS 2008 1.G Owners Manual

Running the Vehicle While Parked
It is better not to park with the engine running. But if you
ever have to, here are some things to know.
{CAUTION:
Idling the engine with the climate control
system off could allow dangerous exhaust into
your vehicle. See the earlier caution under
Engine Exhaust on page 2-34.
Also, idling in a closed-in place can let deadly
carbon monoxide (CO) into your vehicle even if
the climate control fan is at the highest setting.
One place this can happen is a garage.
Exhaust — with CO — can come in easily.
NEVER park in a garage with the engine
running.
Also see “If You Are Caught in a Blizzard” under
Winter Driving on page 4-16.
{CAUTION:
It can be dangerous to get out of your vehicle if
the shift lever is not fully in PARK (P) with the
parking brake rmly set. Your vehicle can roll.
Do not leave your vehicle when the engine is
running unless you have to. If you have left the
engine running, the vehicle can move suddenly.
You or others could be injured. To be sure your
vehicle will not move, even when you are on
fairly level ground, always set the parking brake
after you move the shift lever to PARK (P).
Follow the proper steps to be sure your vehicle will not
move. SeeShifting Into Park on page 2-31.
If you are parking on a hill and if you are pulling a
trailer, also seeTowing a Trailer on page 4-27.
2-35

Mirrors
Automatic Dimming Rearview Mirror
The vehicle has an automatic dimming rearview
mirror with a compass display. The mirror may also
have OnStar
®controls and/or Intellibeam™. For more
information on OnStar, seeOnStar®System on
page 2-49. For more information on Intellibeam™ see
“Intellibeam Intelligent High-Beam Headlamp Control
System” underExterior Lamps on page 3-32.
O(On/Off):If the vehicle has this button, press to
turn the automatic dimming feature on or off.
Automatic Dimming Mirror Operation
Automatic dimming reduces the glare of lights from
behind the vehicle. The dimming feature comes on and
the indicator light illuminates each time the vehicle is
started.
Cleaning the Mirror
Do not spray glass cleaner directly on the mirror. Use a
soft towel dampened with glass.
Compass
Compass Operation
AUTO3/O(Auto Highbeam or On/Off):The
vehicle may have one of these buttons. Press and
hold AUTO
3for approximately three seconds or
press
Oto turn the compass on or off.
When the ignition is turned ON and this feature is on,
the compass displays in the mirror after a few seconds.
Compass Calibration
If the letter C should ever appear in the compass
display window, the compass may need to be calibrated.
If the correct compass direction does not show on the
display, there may be a strong magnetic eld interfering
with the compass, such as a magnetic antenna
mount, magnetic note pad holder or a similar magnetic
item. Remove the interference and calibrate the
compass, if calibrating is needed.
The compass can be placed in calibration mode
manually by pressing and holding AUTO
3orO
depending on the vehicle, until a C is shown in the
compass display.
To calibrate, drive the vehicle in a small circle slowly
until the display reads the correct direction.
2-36

Compass Variance
The mirror is set to zone eight. If you do not live in zone
eight or drive out of the area, the compass variance
needs to be changed to the appropriate zone.
To adjust for compass variance do the following:
1. Find the current location and variance zone number
on the following zone map.
2. Press and hold AUTO
3orOdepending on the
vehicle, until a zone number displays.
3. Once the zone number displays, press AUTO
3or
Omultiple times until the correct zone number
displays. Stop pressing the button and the mirror
returns to normal operation. If C appears in the
compass window, the compass may need
calibration. See Compass Calibration listed
previously.
2-37

Outside Power Foldaway Mirrors
The mirror controls are
located on the driver door
armrest.
Power Mirror Adjustment
1. Press (A) or (B) to select the driver or passenger
side mirror.
2. Press the arrows located on the four-way control
pad to adjust the mirror.
3. Press (A) or (B) again to deselect the mirror.
Power Foldaway Mirror Adjustment
1. Press (C) to fold the mirrors out to the driving
position.
2. Press (D) to fold the mirrors in to the folded
position.
Resetting the Power Foldaway Mirrors
Reset the power foldaway mirrors if:
The mirrors are accidentally obstructed while
folding.
They are accidentally manually folded/unfolded.
The mirrors do not stay in the unfolded position.
The mirrors vibrate at normal driving speeds.
Fold and unfold the mirrors one time using the mirror
controls to reset them to their normal position.
2-38

Outside Automatic Dimming Mirror
If the vehicle has this feature, the driver side mirror
adjusts for the glare of headlamps behind you.
This feature is controlled by the on and off settings on
the automatic dimming rearview mirror.
Park Tilt Mirrors
If your vehicle is equipped with memory mirrors, it will
also be capable of performing the park tilt mirror feature.
This feature allows the driver and passenger side
mirror to tilt to a factory programmed position when the
vehicle is in R (Reverse). This feature may be useful
in allowing you to view the curb when you are parallel
parking.
When the vehicle is shifted out of R (Reverse) and
either a ve-second delay has occurred, or the ignition
is turned to LOCK/OFF, the driver’s and passenger’s
side mirror will return to its original position.
This feature can be enabled/disabled through the Driver
Information Center (DIC). SeeDIC Vehicle
Customization on page 3-87.
Outside Convex Mirror
{CAUTION:
A convex mirror can make things (like other
vehicles) look farther away than they really are.
If you cut too sharply into the right lane, you
could hit a vehicle on your right. Check your
inside mirror or glance over your shoulder
before changing lanes.
The passenger side mirror is convex. A convex mirror’s
surface is curved so more can be seen from the driver
seat. This mirror does not have a dimming feature.
Outside Heated Mirrors
=(Rear Window Defogger):Press to heat the
outside rearview mirrors. See “Rear Window Defogger”
underDual Climate Control System on page 3-42for
more information.
Side Blind Zone Alert (SBZA)
If your vehicle has the Side Blind Zone Alert (SBZA)
system, seeSide Blind Zone Alert (SBZA) on page 2-43.
2-39

Object Detection Systems
Ultrasonic Front and Rear Parking
Assist (UFRPA)
If your vehicle has the Ultrasonic Front and Rear
Parking Assist (UFRPA) system, it helps you park easier
and helps you avoid colliding with objects such as
parked vehicles. It operates at speeds less than 5 mph
(8 km/h). It can determine how close objects are to
the front bumper, up to 4 feet (1.2 m) in front of your
vehicle and the rear bumper, up to 8 feet (2.5 m) behind
your vehicle. The distance sensors are located on the
front and rear bumper.
{CAUTION:
The Ultrasonic Front and Rear Park Assist
(UFRPA) system does not replace driver
vision. It cannot detect:
objects that are below the bumper,
underneath the vehicle, or if they are too
close or far from the vehicle
children, pedestrians, bicyclists, or pets.
If you do not use proper care before moving
forward and while backing; vehicle damage,
injury, or death could occur. Even with UFRPA,
always check in front of your vehicle before
moving forward and behind your vehicle
before backing up. While moving forward and
backing, be sure to look for objects and check
your vehicle’s mirrors.
2-40

The front display is located on top of the instrument panel
to the right of the driver. The front display will have either
three or six lights to provide distance and system
information. With Adaptive Cruise control (ACC), it will
have three lights along with the ACC lights. Without ACC,
it will have six lights. High-toned beeps from the front
speakers are for objects detected near the front bumper.
The rear display is located near the rear window and
can be seen by looking over your right shoulder.
The rear display uses three color-coded lights to provide
distance and system information. Low-toned beeps
from the rear speakers are for the rear bumper.
How the System Works
UFRPA comes on automatically when the shift
lever is moved out of PARK (P). The system does
not work at a forward or reverse speed greater than
5 mph (8 km/h).
To be detected, objects must be at least 10 inches
(25.4 cm) off the ground and below hood or trunk level.
Objects must also be within 4 feet (1.2 m) in front of
your vehicle and 8 feet (2.5 m) from your rear bumper.
This distance may be less during warmer or humid
weather.
When backing, if objects are detected at the same time
near both the front and rear bumpers, both color-coded
light displays will notify you of objects close to each
bumper. If there are objects detected near both bumpers,
the beeps will only be sounded to notify that objects are
close to the rear bumper. However, if while you are
backing and an object comes within 1 ft (0.3 m) of the
front bumper, and at the same time there is another
object further than 1 ft (0.3 m) from the rear bumper, then
the beeps will only be sounded to notify you of the closer
object that is near the front bumper.
The system can be disabled using the Driver Information
Center (DIC). See “Parking Assist” underDIC Operation
and Displays on page 3-70for more information. Front Parking Assist
Display
Rear Parking Assist
Display
2-41

Moving Forward
When the vehicle is started, the front display will briey
illuminate to let you know the system is working.
The following describes what will occur with the front
display as you get closer to a object detected in the front
of your vehicle:
Description English Metric
amber/amber lights
ACC — one amber light4 ft 1.2 m
four amber lights
ACC — two amber lights40 in 1.0 m
four amber/ two red lights
ACC — two amber
lights/one red light23 in 0.6 m
four amber/ two red lights
and beep for
three seconds
ACC — two amber
lights/one red light and
beep for three seconds1 ft 0.3 m
Backing
URPA comes on automatically when the shift lever is
moved into REVERSE (R). The rear display will then
briey illuminate to let you know the system is working.
The following describes what will occur with the rear
display as you get closer to an object detected in
the rear of your vehicle:
Description English Metric
amber light 8 ft 2.5 m
amber/amber lights 40 in 1.0 m
amber/amber/red lights 23 in 0.6 m
amber/amber/red lights
ashing and beep for
three seconds1 ft 0.3 m
The system can be disabled through the Driver
Information Center (DIC). See “Parking Assist” under
DIC Operation and Displays on page 3-70for more
information.
2-42

When the System Does Not Seem to
Work Properly
The driver disables the system.
The parking brake pedal is depressed.
The ultrasonic sensors are not kept clean. So be
sure to keep your vehicle’s front and rear bumpers
free of mud, dirt, snow, ice and slush. For cleaning
instructions, seeWashing Your Vehicle on
page 5-94.
A trailer was attached to your vehicle, or a bicycle or
an object was hanging out of your trunk during your
last drive cycle, the red light may illuminate in the
rear display. Once the attached object is removed,
UFRPA will return to normal operation.
A tow bar is attached to your vehicle.
The vehicle’s bumper is damaged. Take the vehicle
to your dealer/retailer to repair the system.
Other conditions may affect system performance,
such as vibrations from a jackhammer or the
compression of air brakes on a very large truck.
If the system is still disabled after driving forward at
least 15 mph (25 km/h), take your vehicle to your
dealer/retailer.
Side Blind Zone Alert (SBZA)
Your vehicle may have a Side Blind Zone Alert (SBZA)
system. Read this entire section before using the system.
The SBZA system operates on a radio frequency
subject to Federal Communications Commission (FCC)
Rules and with Industry Canada.
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This device complies with RSS-310 of Industry Canada.
Operation is subject to the following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
Frequency of operation: 24.05GHz – 24.25GHz
Field Strength: Not greater than 2.5V/m peak (0.25V/m
average) at a distance of 3m
2-43

The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modications to
this equipment. Such modications could void the user’s
authority to operate the equipment.
{CAUTION:
SBZA is only a lane changing aid and does not
replace driver vision. SBZA does not detect:
Vehicles outside the side blind zones
which may be rapidly approaching.
Pedestrians, bicyclists, or animals.
Failure to use proper care when changing
lanes may result in damage to the vehicle,
injury, or death. Always check the outside and
rearview mirrors, glance over your shoulder,
and use the turn signal before changing lanes.
When the system detects a vehicle in the side blind zone,
amber SBZA displays will light up in your side mirrors.
This indicates that it may be unsafe for you to change
lanes. Before making a lane change, always check the
SBZA display, check the outside and rearview mirrors,
look over your shoulder for vehicles and hazards, and
use the turn signal.
SBZA Detection Zones
The SBZA sensor covers a zone of approximately one
lane over from both sides of the vehicle, 11 ft. or 3.5 m.
This zone starts at each side mirror and goes back
approximately 16 ft. (5.0 m). The height of the zone is
approximately between 1.5 ft. (0.5 m) and 6 ft. (2.0 m) off
the ground.
The SBZA detection zones do not change if your
vehicle is towing a trailer. So be extra careful when
changing lanes while towing a trailer.
2-44