mirror controls CADILLAC ESCALADE EXT 2002 2.G Owners Manual

1-3 Memory Seat and Memory Mirrors
The memory function controls are located on the
driver's door trim panel.
For this function to work, it must be enabled/configured
in the Secondary Information Center (SIC).
See ªSecondary Information Centerº in the Index
for more information.These buttons are used to program and recall the
memory settings for the driver's seat and both
the driver's and the passenger's outside mirrors.
The seat and mirror positions can be personalized
for both driver 1 and driver 2. Driver 1 or driver 2
corresponds to the memory buttons labeled 1 and 2
on the control.
The memory function does not store the lumbar or
back support positions.
To set your memory seat and mirrors do the following:
1. Adjust the driver's seat and both outside mirrors to
the desired position.
2. Press and hold the 1 or 2 (driver 1 or 2) button of the
memory control for three seconds. When you hear a
chime ring two times, the memory position is stored.
To do the same thing for a second driver, follow the
preceding steps, but press the other number of the
memory control. The memory feature only works when
the transmission is in PARK (P).

1-5
Memory Seat and Outside Rearview Mirror Recall
You can program your keyless entry transmitter to recall
seat and mirror settings for up to two drivers. Once a
transmitter is programmed, press the UNLOCK button
to recall the seat and mirror settings.
To program a transmitter do the following:
1. Press and hold the desired button 1 or 2 on the
memory controls.
2. Press UNLOCK on the keyless entry transmitter that
corresponds with the specific memory button 1 or 2
pressed in Step 1.
That transmitter will now correspond with the memory
button 1 or 2 and the memory settings that are set for
that number.
Your vehicle comes with two keyless entry transmitters.
The other transmitter may be programmed by following
these steps using the other memory button.Heated Front Seats
The button for the
driver's side heated seat
is located on the driver's
side door panel.
The button for the passenger's side heated seat is located
on the passenger's side door panel. The ignition must be
in RUN for this feature to operate.
To activate the heated seats, press the button once for
the HI (high) heat setting. Press the button again for the
LO (low) heat setting. To turn off the heated seats, press
the button a third time. An indicator light near the button
will illuminate for each heat setting any time the heated
seats are operating.
The heated front seats will be canceled after the ignition
is turned to OFF. If you still want to use the heated front
seat feature after you restart your vehicle, you will need
to press the heated seat button again.

2-
2-1
Section 2 Features and Controls
Here you can learn about the many standard and optional features on your vehicle, and information on starting,
shifting and braking. Also explained are the instrument panel and the warning systems that tell you if everything is
working properly
-- and what to do if you have a problem.
2
-2 Windows
2-4 Keys
2-6 Door Locks
2-8 Keyless Entry System
2
-11 Midgate
2-22 Tailgate
2-23 Theft
2-24 Content Theft-Deterrent
2
-26 Passlock

2-26 New Vehicle ªBreak-Inº
2-27 Ignition Positions
2-28 Starting Your Engine
2-29 Engine Coolant Heater (If Equipped)
2-31 Automatic Transmission Operation
2-35 Parking Brake
2-36 Shifting Into PARK (P)
2-38 Shifting Out of PARK (P)
2-39 Parking Over Things That Burn
2-39 Engine Exhaust
2-40 Running Your Engine While You're Parked
2-41 Road Sensing Suspension
2-41 Locking Rear Axle2
-41 All-Wheel Drive
2-41 Horn
2-42 Tilt Wheel
2-42 Turn Signal/Multifunction Lever
2-49 Exterior Lamps
2-53 Interior Lamps
2-55 Mirrors
2-62 Storage Compartments
2-64 Cargo Cover Panels
2-81 Ashtray and Cigarette Lighter
2-82 Accessory Power Outlets
2-83 Analog Clock
2
-84 OnStar
System (If Equipped)
2-87 Sunroof (If Equipped)
2
-88 Homelink
Transmitter
2-92 The Instrument Panel - Your
Information System
2
-94 Instrument Panel Cluster
2-96 Warning Lights, Gages and Indicators
2-109 Message Center
2-117 Secondary Information Center (SIC)
2
-124 Ultrasonic Rear Parking Assist (URPA)

2-59
Power Outside Rearview Mirrors
The controls are located on
the driver's door armrest.
Move the selector switch to the left or right to choose
the mirror you want to adjust, then use the arrows on the
lower control pad to adjust the mirror.
The mirrors include ground illumination lamps (puddle
lamps) in the base of the mirror. For more information
on these lamps, see ªPuddle Lampsº in the Index.
Driver's Outside Auto-Dimming
Rearview Mirror
The driver's electrochromic outside mirror will adjust
for the glare of headlamps behind you. This feature is
controlled using the on and off settings found on the
electrochromic mirror. See ªElectrochromic Day/Night
Rearview Mirror with Compass and Temperatureº in
the Index.

2-60
Curb View Assist Mirrors
Your vehicle is equipped with the curb view assist
mirror feature. For this function to work, it must be
enabled in the SIC. See ªSICº in the Index for more
information.
When the vehicle is shifted into REVERSE (R) there
will be a three second delay before the curb view assist
mirror(s) tilt to a preselected position. This feature may
be useful in allowing you to view the curb when you are
parallel parking.
When the vehicle is shifted out of REVERSE (R) and a
five
-second delay has passed, the selected mirrors will
return to the original position.
If further adjustment is needed after the mirror is tilted,
the mirror controls may be used.Adjusting the Tilt Angle of the Mirrors
Adjust the tilt angle for each outside mirror by doing
the following:
1. Enable the feature in the SIC (if it is not already).
See ªSICº in the Index for information on enabling
the tilt mirrors.
2. Place the vehicle in REVERSE (R) and allow the
mirrors to tilt.
3. Change the angle of the mirror tilt to the desired
angle with the mirror controls.
The mirrors are now set to the desired position. The next
time the vehicle is placed in REVERSE (R) and the
mirror tilt feature is enabled in the SIC, the mirrors will
move to the set position.

2-93
The main components of your instrument panel are the following:
A. Dome Override Button
B. Exterior Lamps Control
C. Air Outlets
D. Folding Mirrors Button
E. Cargo/Top
-Box Lamps Button
F. Multifunction Lever
G. Instrument Panel Cluster
H. Shift Lever
I. Tow/Haul Selector Button
J. Audio System
K. Comfort Control System
L. Instrument Panel Fuse Block
M. Hood ReleaseN. Fog Lamps Button
O. Audio Steering Wheel Controls
P. Center Instrument Panel Utility Block
Q. Tilt Lever
R. Parking Brake Release
S. Secondary Information Center (SIC)
T. Rear Window Defogger Button
U. Compact Disc Changer
V. Ashtray
W. Clock
X. Ultrasonic Rear Parking Assist Button
Y. StabiliTrak Button
Z. OnStar Buttons

6-73
Name Usage
STUD #1 Accessory Power/Trailer Wiring
Feed/Load Leveling
ABS Anti
-Lock Brakes
IGN A Ignition Switch
AIR A.I.R. System
RAP #1 Retained Accessory Power, Power
Mirrors, Power Door Locks,
Power Seat(s)
IGN B Ignition Switch
RAP #2 Retained Accessory Power/Rear
Power Windows, Sunroof, Radio
STUD #2 Accessory Power/Trailer Wiring
Brake Feed
TRL R TRN Right Turn Signal Trailer Wiring
TRL L TRN Left Turn Signal Trailer Wiring
IGN 1 Ignition, Fuel Controls
INJ B Ignition, Fuel Controls (Relay)
STARTER Starter (Relay)Name Usage
PARK LP Parking Lamps
FRT HVAC Climate Control System
STOP LP Exterior Lamps, Stoplamps
ECM 1 VCM/PCM
CHMSL Center High Mounted Stoplamp
VEH STOP Stoplamps, Cruise Control
TRL B/U Backup Lamps Trailer Wiring
INJ A Fuel Controls, Ignition
RR HVAC Rear Climate Control System
VEH B/U Vehicle Backup Lamps
ENG 1 Engine Controls, Canister Purge,
Fuel System
ETC Electronic Throttle Control
IGN E A/C Compressor Relay, Rear
Window Defogger, Daytime
Running Lamps, A.I.R. System
B/U LP Backup Lamps, Automatic
Transmission Shift Lock
Control System