ECO mode CADILLAC STS V 2007 1.G Owner's Manual

Did you just drive through a deep puddle of water?
If so, your vehicle’s electrical system may be wet.
The condition will usually be corrected when
the electrical system dries out. A few driving trips
should turn the light off.
Have you recently changed brands of fuel?
If so, be sure to fuel your vehicle with quality fuel.
SeeGasoline Octane on page 365. Poor fuel
quality will cause the engine not to run as
efficiently as designed. You may notice this as
stalling after start-up, stalling when you put
the vehicle into gear, misring, hesitation on
acceleration, or stumbling on acceleration. (These
conditions may go away once the engine is
warmed up.) This will be detected by the system
and cause the light to turn on.
If you experience one or more of these conditions,
change the fuel brand you use. It will require at
least one full tank of the proper fuel to turn the
light off.
If none of the above steps have made the light
turn off, your dealer can check the vehicle.
Your dealer has the proper test equipment and
diagnostic tools to x any mechanical or electrical
problems that may have developed.Emissions Inspection and Maintenance
Programs
Some state/provincial and local governments have
or may begin programs to inspect the emission
control equipment on your vehicle. Failure to pass
this inspection could prevent you from getting a
vehicle registration.
Here are some things you need to know to help
your vehicle pass an inspection:
Your vehicle will not pass this inspection if the
check engine light is on or not working properly.
To perform a check engine light bulb check with the
keyless ignition, make sure the transmitter fob is in
the passenger compartment. SeeIgnition Positions
on page 111. Press the bottom of the Acc. button
on the instrument panel and hold the button down
for ve seconds. The instrument panel, including
the check engine light, will light up and the ignition
will be on, but the engine will not start — if you
press the bottom of the Acc. button only briey, less
than ve seconds, the accessory power mode will
be turned on, but not the ignition. After the bulb
check, be sure to press and release the Acc. button
again to turn the ignition off and avoid draining the
vehicle’s battery.
254

CHECK WASHER FLUID
This symbol appears
with this message.
This message displays when your vehicle is low
on windshield washer uid. Rell the windshield
washer uid reservoir as soon as possible.
SeeWindshield Washer Fluid on page 404for
more information.
CLEAN RADAR
This message displays when the Adaptive Cruise
Control system is disabled because the radar
is blocked and cannot detect vehicles in your path.
It may also activate during heavy rain or due to
road spray. To clean the system, see “Cleaning the
System” underAdaptive Cruise Control on
page 197.
COMPETITIVE DRIVING (STS-V Only)
This message displays when the competitive
driving mode is turned on with the traction control
button. The TC (traction control) light comes on
when the competitive driving mode is on. The
Traction Control System (TCS) will not operate
while in competitive driving mode. Adjust your
driving accordingly. SeeCompetitive Driving Mode
(STS-V) on page 325for more information.
DRIVER DOOR AJAR
This symbol appears
with this message.
This message displays if the driver’s door was not
closed completely. Make sure that the driver’s
door is closed completely.
268

ENGINE COOLANT HOT IDLE ENGINE
Notice:If you drive your vehicle while the
engine is overheating, severe engine damage
may occur. If an overheat warning appears
on the instrument panel cluster and/or DIC,
stop the vehicle as soon as possible. Do not
increase the engine speed above normal idling
speed. SeeEngine Overheating on page 393
for more information.
This symbol appears
with this message.
This message displays when the engine coolant
temperature is too hot. Stop and allow the vehicle
to idle until it cools down. SeeEngine Coolant
Temperature Warning Light on page 251.
SeeOverheated Engine Protection Operating
Mode on page 395for information on driving to a
safe place in an emergency.
ENGINE HOT –
AC (Air Conditioning) OFF
This message displays when the engine coolant
becomes hotter than the normal operating
temperature. SeeEngine Coolant Temperature
Gage on page 251. To avoid added strain on a hot
engine, the air conditioning compressor is
automatically turned off. When the coolant
temperature returns to normal, the air conditioning
compressor turns back on. You can continue to
drive your vehicle.
If this message continues to appear, have the
system repaired by your dealer as soon as
possible to avoid damage to the engine.
269

SERVICE TIRE MONITOR
If your vehicle has a Tire Pressure Monitor (TPM)
system, this message displays if a part on the
system is not working properly. If you drive your
vehicle while any of the four sensors are
missing or inoperable, the warning comes on in
about 20 minutes. A sensor would be missing, for
example, if you put different wheels on your
vehicle without transferring the sensors. If the
warning comes on and stays on, there may be a
problem with the TPM. See your dealer.
SERVICE THEFT SYSTEM
This message displays when there is a problem
with the hood open and closed switches. The
switches may need to be replaced. When
this message is displayed, the theft-deterrent
system will still be protecting the interior of
the vehicle, however, the hood area will not be
protected at this time. Also, the remote start
function will not work when this message appears.
See your dealer for service.
SERVICE TRANSMISSION
This message displays when there is a problem
with the transmission of your vehicle. Have
your vehicle serviced by your dealer.
SERVICE VEHICLE SOON
This message displays when a non-emissions
related malfunction occurs. Have your vehicle
serviced by your dealer as soon as possible.
SPEED LIMITED TO XXX
This message displays when your vehicle speed is
limited to XXX, mph in English mode and km/h
in Metric mode, because the vehicle detects
a problem in the suspension system. Have your
vehicle serviced by your dealer.
STABILITY SYS (System) ACTIVE
This message displays any time the StabiliTrak®
System is actively assisting you with directional
control of the vehicle. Slippery road conditions may
exist when this message is displayed, so adjust
your driving accordingly. This message may
stay on for a few seconds after StabiliTrak
®stops
assisting you with directional control of the
vehicle. SeeStabiliTrak
®System on page 326for
more information.
276

Playing the Radio
O
(Power):Press this knob to turn the system
on and off.
n(Volume):Turn this knob clockwise or
counterclockwise to increase or to decrease
the volume.
SRCE (Source):Press this button to select a
source, either radio or CD. The CD must be loaded
to select the source and to play. CD displays if
a CD is loaded. If a CD is not loaded, the display
does not change from the radio source.
Finding a Station
BAND:Press this button to select FM1, FM2, AM,
or XM1 or XM2 (if equipped).
w(Tune):Turn this knob to select radio stations.
©¨(Seek):Press the left single arrow button to
go to the previous station and stay there. Press the
right single arrow button to go to the next station
and stay there. The sound mutes while seeking.
The radio seeks stations only with a strong signal
that are in the selected band.
©¨(Scan):Press the double arrow scan button
to enter scan mode. SCAN displays. Press this
button to scan to the next station. The radio goes to
a station, plays for ve seconds, then goes to the
next station. Press this button again to stop
scanning.
To scan preset stations, press and hold the double
arrow scan button for more than two seconds until a
beep sounds and PSCAN displays. The radio goes
to the rst preset station, plays for ve seconds,
then goes to the next preset station. Press this
button again to stop scanning presets.
The radio only scans stations with a strong signal
that are in the selected band.
ALOCAL/DISTANT Selection:With this feature
the radio can be set to search for local stations
or stations that are further away for a larger
selection.
To set this feature to LOCAL or DISTANT,
perform the following steps:
1. Press the tune/select knob to enter the
main menu.
2. Turn the tune/select knob until SEEK LOCAL
or SEEK DISTANT displays.
284

Adjusting the Speakers (Balance/Fade)
To adjust the balance or fade, perform the
following steps:
1. Press the tune/select knob to enter the
main menu.
2. Turn the tune/select knob until
BASS-MID-TREBLE displays.
3. Press the tune/select knob to enter the tone
settings.
4. Press the tune/select knob to scroll to
BALANCE or FADER.
5. Turn the tune/select knob to adjust the
BALANCE to the right or the left speakers and
the FADER to the front or the rear speakers.
6. Press the tune/select knob to set the
adjustment.
7. Press the BACK (F6) button to exit the
display. To return to the original display,
repeatedly press the BACK (F6) button or wait
for the display to time out.
EQ0 does not appear on the display while in
this mode.
RDS Messages
ALERT:Alert warns of local and national
emergencies. When, an alert announcement comes
on the current radio station or a related network
station, ALERT displays. You will hear the
announcement, even if the volume is low or a CD is
playing. If a CD is playing, play stops during the
announcement. Alert announcements cannot be
turned off. If the radio tunes to a related network
station for the announcement, it returns to the
original station when the announcement is nished.
ALERT is not affected by tests of the emergency
broadcast system. This feature is not supported by
all RDS stations.
MSG (Message):If the current RDS station has a
message, MSG displays. The message can
display the artist, song title, call in phone numbers,
etc. If the entire message does not display,
parts of the message displays every three seconds
until the message is complete. Once the
completed message has displayed, MSG
disappears from the display until another new
message is received.
288

F5 MODE:Press this pushbutton to select from
NORMAL, RPT TRCK (Repeat Track), RPT
DISC (Repeat CD), RDM TRCK (Random Track),
and RDM ALL (Random All CDs).
NORMAL:Sets the system for normal play of
the CD(s). NORMAL does not display while in
this mode.
RPT TRCK (Repeat Track):Repeats the track
over again. RPT TRCK displays. Press the
MODE pushbutton again to turn off repeat play.
RPT TRCK disappears from the display.
RPT DISC (Repeat CD):Repeats the CD over
again. RPT DISC displays. Press the MODE
pushbutton again to turn off repeat play.
RPT DISC disappears from the display.
RDM TRCK (Random Track):Plays the tracks
on the current CD in random, rather than
sequential, order. RDM TRCK appears on the
display. Press the MODE pushbutton again to
turn off random play. RDM TRCK disappears
from the display.
RDM ALL (Random All CDs):Plays all of the
CDs loaded in random, rather than sequential,
order. RDM ALL displays. Press the MODE
pushbutton again to turn off random play. RDM
ALL disappears from the display.F6 DISP (Display):Press this pushbutton to
display the time of the track. Press this pushbutton
again to display CD PLAY MODE.
©¨(Seek):Press the left single arrow button to
go to the previous or press the right single
arrow button to go to the next track on the CD.
©¨(Scan):Press this double arrow button
to listen to each track for 10 seconds. The CD
goes to a track, play for 10 seconds, then go on to
the next track. Press this button again to stop
scanning.
SRCE (Source):Press this button to select a
source, either radio or CD. The CD must be loaded
to select the source and to play. CD displays if
a CD is loaded. If a CD is not loaded, the display
does not change from the radio source.
Z(Eject):Press this button to eject the CD that
is currently playing, or press and hold this
button to eject all of the CDs loaded. A beep
sounds. Eject can be activated with the ignition or
radio off.
295

As each new track starts to play, the track
number displays.
The CD player can play the smaller 3 inch (8 cm)
single CDs with an adapter ring. Full-size CDs
and the smaller CDs are loaded in the same
manner.
If playing a CD-R, the sound quality can be
reduced due to CD-R quality, the method of
recording, the quality of the music that has been
recorded, and the way the CD-R has been
handled. There can be an increase in skipping,
difficulty in nding tracks, and/or difficulty in loading
and ejecting. If these problems occur, check the
bottom surface of the CD. If the surface of the CD
is damaged, such as cracked, broken, or
scratched, the CD will not play properly. If the
surface of the CD is soiled, seeCare of Your CDs
on page 313for more information.
If there is no apparent damage, try a known
good CD.
Do not add any label to a CD, it could get caught
in the CD player. If a CD is recorded on a
personal computer and a description label is
needed, try labeling the top of the recorded CD
with a marking pen.Notice:If a label is added to a CD, or more
than one CD is inserted into the slot at a time,
or an attempt is made to play scratched or
damaged CDs, the CD player could be
damaged. While using the CD player, use only
CDs in good condition without any label,
load one CD at a time, and keep the CD player
and the loading slot free of foreign materials,
liquids, and debris.
If an error displays, see “CD Messages” later in
this section.
F1
r(Previous Folder):Press this pushbutton
to go to the rst track in the previous folder.
Press and hold this pushbutton to reverse quickly
within a track. Release this pushbutton to play
the passage. REV and the elapsed time of
the track displays.
Pressing this button while in folder random mode
goes to the previous folder and plays the tracks
in that folder in random order.
300

F2[(Next Folder):Press this pushbutton to go
to the rst track in the next folder.
Press and hold this pushbutton to advance quickly
within a track. Release this pushbutton to play
the passage. FWD and the elapsed time of
the track displays.
Pressing this button while in folder random mode
takes you to the next folder and plays the
tracks in that folder in random order.
F3 RDM (Random):To play the tracks on the CD
in random, rather than sequential order, press
and release this pushbutton until RDM TRCK
displays. Once all of the tracks in the current folder
or playlist have played, the system moves on to
the next folder or playlist and plays all of the tracks
in random order.
To play the tracks in the current folder in random,
rather than sequential order, press and release
this pushbutton until RDM FLDR displays.
This feature does not work with playlists.
While in random, pressing and releasing either
single seek arrow goes to the next or previous
random track.Press and release this pushbutton until NORMAL
displays to turn off random play.
F4 RPT (Repeat):To repeat the current track,
press and release this pushbutton until RPT
TRCK displays.
To repeat the tracks in the current folder,
press and release this pushbutton until RPT
FLDR displays.
Press and release this pushbutton until NORMAL
displays to turn off repeated play.
F6 DISP (Display):Press this pushbutton to
switch between the elapsed time of the track and
the MP3 playback information.
©¨(Seek):Press the left arrow to go to the
start of the previous track. Press the right arrow to
go to the start of the next track. Pressing either
arrow for more than two seconds searches
the previous or next tracks at two tracks per
second. Release the button to stop searching and
to play the track.
301

Your Driving, the Road, and
Your Vehicle............................................ 316
Defensive Driving...................................... 316
Drunken Driving........................................ 317
Control of a Vehicle.................................. 320
Braking...................................................... 320
Anti-Lock Brake System (ABS).................. 321
Braking in Emergencies............................. 323
Traction Control System (TCS).................. 323
Competitive Driving Mode (STS-V)............ 325
Magnetic Ride Control............................... 325
Limited-Slip Rear Axle............................... 325
StabiliTrak
®System................................... 326
Panic Brake Assist.................................... 327
All-Wheel Drive (AWD) System.................. 327
Steering.................................................... 327
Off-Road Recovery.................................... 330
Passing..................................................... 330
Loss of Control.......................................... 332Competitive Driving................................... 333
Driving at Night......................................... 333
Driving in Rain and on Wet Roads............ 335
City Driving............................................... 338
Freeway Driving........................................ 339
Before Leaving on a Long Trip.................. 340
Highway Hypnosis..................................... 341
Hill and Mountain Roads........................... 342
Winter Driving........................................... 344
If Your Vehicle is Stuck in Sand,
Mud, Ice, or Snow ................................. 348
Rocking Your Vehicle to Get It Out........... 349
Loading Your Vehicle................................ 349
Towing........................................................ 355
Towing Your Vehicle ................................. 355
Recreational Vehicle Towing...................... 355
Towing a Trailer........................................ 357
Section 4 Driving Your Vehicle
315