horn CADILLAC XLR 2009 1.G Owners Manual

Keyless Trunk Opening
Press the trunk release sensor, located on the rear of
the trunk lid under the emblem, to open the trunk if the
keyless access transmitter is within range. SeeTrunk
on page 2-14for additional information.
There are other conditions which can affect the
performance of the transmitter. SeeKeyless Access
System on page 2-4.
This vehicle comes with
two transmitters.
Q(Lock):Press to lock
the doors. The indicator
light on the door ashes
once. If
Qis pressed twice,
the doors lock, the light
ashes once and the horn
sounds once.
K(Unlock):Press once to unlock the driver door.
The indicator light on the door ashes twice.
Press
Ktwice within ve seconds to unlock both
doors. The interior lamps may come on.Pressing
Kalso recalls the memory settings. See
Memory Seat, Mirrors and Steering Wheel on page 1-3
for more information.
G(Trunk):Press and hold for about one second to
open the trunk. If the engine is running, the shift lever
must be in P (Park).
L(Panic):Press to sound the vehicle alarm. Press
any other button on the keyless access transmitter
to stop the vehicle alarm.
The vehicle comes with two transmitters. Each
transmitter will have a number on top of it,″1″or″2″.
These numbers correspond to the driver of the vehicle.
For example, the memory seat position for driver 1
will be recalled when using the transmitter labeled″1″,
if enabled through the vehicle personalization. See
Memory Seat, Mirrors and Steering Wheel on page 1-3
andDIC Vehicle Personalization on page 3-72.
Programming Transmitters to the
Vehicle
Only keyless access transmitters programmed to this
vehicle will work. If a transmitter is lost or stolen, a
replacement can be purchased and programmed through
your dealer/retailer. The vehicle can be reprogrammed so
that lost or stolen transmitters no longer work. Each
vehicle can have up to four transmitters programmed to it.
2-6

Power Door Locks
The power door lock switches are located on the doors.
There is an indicator light on the rear of the door
near the window.
K(Unlock):Press to unlock the doors.
When pressed, a beep sounds. If the door is closed
when pressed, the light ashes twice. If the door is open
when pressed, the light ashes.
Q(Lock):Press to lock the doors.
When pressed, a beep sounds. If the door is closed
when pressed, the light comes on for a few seconds,
then turns off. If the door is open when pressed, the light
stays on.
Automatic Door Lock
Your vehicle is programmed so that, when the doors are
closed, the ignition is on and the shift lever is moved out
of P (Park), all the doors will lock.
If someone needs to get out while the vehicle is not in
P (Park), have the person use the power door unlock
switch. When the door is closed again, the doors will lock
either when your foot is removed from the brake or the
vehicle speed becomes faster than 8 mph (13 km/h).
Programmable Automatic Door
Unlock
Your vehicle is programmed so that, when the shift
lever is moved into P (Park), both doors will unlock.
With the vehicle in P (Park) and the engine running,
door unlocking can be programmed through prompts
displayed on the Driver Information Center (DIC).
These prompts allow the driver to choose various
unlock settings. For programming information,
seeDIC Vehicle Personalization on page 3-72.
Lockout Protection
Your vehicle can be programmed to sound the horn
three times and unlock the driver door when both doors
are closed and there is a keyless access transmitter
inside the vehicle. When the driver door is opened,
a reminder chime will sound continuously. The vehicle
will remain locked only when at least one transmitter has
been removed from the vehicle and both doors are
closed. SeeDIC Vehicle Personalization on page 3-72.
2-13

Arming the System
To arm the system:
PressQon the keyless access transmitter.
Open the door. Lock the door with the power door
lock switch. The security light should ash. Remove
the keyless access transmitter from the interior of the
vehicle and close the door. The security light will stop
ashing and stay on. After 30 seconds, the light
should turn off.
The vehicle can be programmed to automatically lock
the doors and arm the system when you exit the
vehicle. SeeDIC Vehicle Personalization on
page 3-72.
Now, if a door or the trunk lid is opened without the
keyless access transmitter, the alarm will go off.
The horn will sound for two minutes, then it will go
off to save battery power. And, the vehicle will not
start without a keyless transmitter present.
The theft-deterrent system will not arm if you lock the
driver door with the power door lock switch after
the doors are closed.
If the passenger stays in the vehicle when you leave with
the keyless access transmitter, have the passenger lock
the vehicle after the doors are closed. This way the alarm
will not arm, and the passenger will not set it off.
Testing the Alarm
To test the system:
1. Close the trunk lid.
2. Lower the window on the driver door.
3. Manually arm the system.
4. Close the doors and wait 30 seconds.
5. Reach through the open window and manually pull
the release lever on the oor.
6. Turn off the alarm by pressing
Kon the transmitter.
If the alarm is inoperative, check to see if the horn
works. If not, check the horn fuse. SeeFuses and Circuit
Breakers on page 6-83. If the horn works, but the
alarm doesn’t go off, see your dealer/retailer.
Disarming the System
Always use the keyless access transmitter to unlock a
door either by pressing
Kon the transmitter or by
squeezing the door handle sensor while you have the
transmitter with you. Unlocking a door any other way will
set off the alarm. If the alarm sounds, press
Kon the
keyless access transmitter to disarm it.
Do not leave the key or device that disarms or
deactivates the theft deterrent system in the vehicle.
2-21

Instrument Panel Overview...............................3-4
Hazard Warning Flashers................................3-6
Horn .............................................................3-6
Power Tilt Wheel and Telescopic Steering
Column......................................................3-6
Heated Steering Wheel...................................3-7
Turn Signal/Multifunction Lever.........................3-7
Turn and Lane-Change Signals........................3-7
Headlamp High/Low-Beam Changer..................3-8
Flash-to-Pass.................................................3-8
Windshield Wipers..........................................3-8
Rainsense™ Wipers.......................................3-9
Windshield Washer.......................................3-10
Headlamp Washer........................................3-11
Cruise Control..............................................3-11
Adaptive Cruise Control.................................3-14
Exterior Lamps.............................................3-26
Wiper Activated Headlamps............................3-27Headlamps on Reminder................................3-27
Daytime Running Lamps (DRL).......................3-27
Adaptive Forward Lighting System...................3-28
Fog Lamps ..................................................3-28
Twilight Sentinel
®..........................................3-29
Exterior Lighting Battery Saver........................3-30
Instrument Panel Brightness...........................3-30
Courtesy Lamps...........................................3-30
Entry/Exit Lighting.........................................3-30
Reading Lamps............................................3-30
Battery Run-Down Protection..........................3-31
Head-Up Display (HUD).................................3-31
Accessory Power Outlet(s).............................3-34
Ashtray(s) and Cigarette Lighter......................3-35
Climate Controls............................................3-36
Dual Climate Control System..........................3-36
Outlet Adjustment.........................................3-40
Passenger Compartment Air Filter...................3-41
Section 3 Instrument Panel
3-1

The main components of the instrument panel are the following:
A.Head-Up Display (HUD) on page 3-31orInstrument
Panel Brightness on page 3-30.
B.Turn Signal/Multifunction Lever on page 3-7.Cruise
Control on page 3-11.Exterior Lamps on page 3-26.
Fog Lamps on page 3-28.
C.Instrument Panel Cluster on page 3-42.
D.Windshield Wipers on page 3-8andWindshield
Washer on page 3-10.
E. Driver Information Center (DIC) Controls/Interior
Lamps. SeeDIC Operation and Displays on
page 3-57.
F.Outlet Adjustment on page 3-40.
G.Hazard Warning Flashers on page 3-6.
H.Audio Steering Wheel Controls on page 3-88.
Adaptive Cruise Control on page 3-14(If Equipped).
Heated Steering Wheel on page 3-7. Voice
Commands. SeeOnStar
®System on page 2-42.I.Power Tilt Wheel and Telescopic Steering Column
on page 3-6.
J.Horn on page 3-6.
K.Ignition Positions on page 2-24.
L. Shift Lever. SeeAutomatic Transmission Operation
on page 2-28.
M.Traction Control System (TCS) on page 5-8.
N.Retractable Hardtop on page 2-54.
O.Cupholders on page 2-53.
P. Cigarette Lighter. SeeAshtray(s) and Cigarette
Lighter on page 3-35.
Q.Dual Climate Control System on page 3-36.
R. Audio/Navigation System. SeeNavigation System
Overview on page 4-2.
S.Glove Box on page 2-53.
3-5

Hazard Warning Flashers
The hazard warning ashers warns others that you have
a problem. The button is located near the center of
the instrument panel.
|:Press to make the front and rear turn signal lamps
ash on and off. Press again to turn the ashers off.
The hazard warning ashers work no matter what mode
the ignition is in, even if the ignition is turned off.
When the hazard warning ashers are on, the turn
signals will not work.
Horn
Press near or on the horn symbols on the steering
wheel pad to sound the horn.
Power Tilt Wheel and Telescopic
Steering Column
The power tilt and
telescope wheel control is
located on the outboard
side of the steering
column.
To operate the power tilt feature, push the control up
and the steering wheel tilts up. Push the control
down and the steering wheel goes down.
Push the control forward and the steering wheel moves
toward the front of the vehicle. Push the control rearward
and the steering wheel moves toward the rear of the
vehicle. To set the memory position, seeDIC Vehicle
Personalization on page 3-72andMemory Seat, Mirrors
and Steering Wheel on page 1-3.
3-6

Security Light
For information regarding
this light and the vehicle’s
security system, see
Theft-Deterrent System
on page 2-20.
Fog Lamp Light
The fog lamp light comes
on when the fog lamps are
in use.
The light goes out when the fog lamps are turned off.
SeeFog Lamps on page 3-28for more information.
Lights On Reminder
This light comes on
whenever the headlamps
are on.
SeeHorn on page 3-6for more information.
Highbeam On Light
This light comes on when
the high-beam headlamps
are in use.
SeeHeadlamp High/Low-Beam Changer on page 3-8
for more information.
United States Only
3-55

Flash at Lock
This feature activates the front and rear turn signals for
one long ash when the lock button on the keyless
access transmitter is pressed. This will only occur when
the vehicle is off. If the lock button is pressed again
within ve seconds, the horn will sound regardless of
which setting you have selected.
The DIC will display NO FLASH AT LOCK or
FLASH AT LOCK. Press the OPTIONS button to
change the setting.
FOB Reminder
This feature sounds the horn three times when the
driver door is closed and there is a keyless access
transmitter inside the interior of the vehicle. This will only
occur when the vehicle is off.
The DIC will display FOB REMINDER OFF or
FOB REMINDER HORN. Press the OPTIONS button
to change the setting.
Passive Locking
This feature allows you to select whether the doors
automatically lock during normal vehicle exit. When the
ignition is turned off and all doors become closed,
the vehicle will determine how many keyless access
transmitters remain in the vehicle interior. If at leastone keyless access transmitter has been removed from
the interior of the vehicle, the doors will lock after
eight seconds.
For example, if there are two keyless access
transmitters in the vehicle and one is removed, the
other will be locked in. The keyless access transmitter
locked in the vehicle can still be used to start the vehicle
or unlock the doors, if needed. A person approaching
the outside of the locked vehicle without an authorized
keyless access transmitter, however, will not be able
to open the door, even with a transmitter in the vehicle.
You may temporarily disable the passive door locking
feature by pressing the door unlock switch for
three seconds on an open door. Passive door locking will
then remain disabled until a door lock switch is pressed or
until the power mode transitions from the off power mode.
You can select to not have the horn sound when the
passive lock occurs. If you choose this setting, the doors
will automatically lock eight seconds after you turn the
ignition off, remove a keyless access transmitter
from the interior of the vehicle, and close both doors.
You can also select to have the horn sound once when
the passive lock occurs. If you choose this setting,
the doors will automatically lock and the horn will chirp
eight seconds after you turn the ignition off, remove
a keyless access transmitter from the interior of
the vehicle, and close both doors.
3-74

If you are parking in a quiet area and do not want the
horn to sound when the doors lock, press the lock button
on the keyless access transmitter immediately after
removing it from the interior and closing the doors.
This will lock the doors and cancel the passive locking
for this ignition cycle.
The DIC will display PASSIVE LOCKING OFF, SILENT
PASSIVE LOCK, or HORN AT PASSIVE LOCK.
Press the OPTIONS button to change the setting.
Passive Unlocking
This feature allows you to select which doors will
automatically unlock when you approach and open
the driver door with the keyless access transmitter.
You can choose to have the driver door unlock or
both doors unlock. SeeDoor Locks on page 2-10for
more information.
The DIC will display PASSIVE UNLK DRIVER or
PASSIVE UNLK BOTH. Press the OPTIONS button to
change this setting.
Auto Unlock
This feature automatically unlocks either the driver door
or both doors, depending on the setting, when the
shift lever is moved to P (Park).
The DIC will display AUTO UNLOCK OFF, AUTO
UNLOCK DRIVER, or AUTO UNLOCK BOTH.
Press the OPTIONS button to change the setting.
Park Assist
This feature tilts the passenger side mirror downward
when the shift lever is moved to R (Reverse). This can
help you to see the curb while backing up. If you
adjust the mirror while in R (Reverse), the new position
will be saved as the park assist position.
The DIC will display PARK ASSIST OFF or
PARK ASSIST ON.
Language
This feature allows you to select the language the
DIC and Head-Up Display (HUD), uses to display
messages.
The DIC will display ENGLISH, FRENCH, GERMAN,
ITALIAN, JAPANESE, or SPANISH. Press the
OPTIONS button to change the setting.
If you become stuck in a language that you do not
understand, hold the OPTIONS and RESET buttons
for ve seconds. The DIC will scroll through all
available languages for as long as the buttons are held.
Each language option will display in its own language.
For example, English will be displayed as ENGLISH,
Spanish as ESPANOL, etc. When the desired language
is available, release the buttons and the DIC will set
to this language.
3-75

Underhood Fuse Block
The underhood fuse block
is located next to the
engine on the passenger
side of the vehicle.
For more information on
location, seeEngine
Compartment Overview on
page 6-12.
Notice:Spilling liquid on any electrical components
on the vehicle may damage it. Always keep the
covers on any electrical component.
To access the fuses, push in the tab located at the end
of the fuse block cover. Then lift the cover open.
Fuses Usage
1Antilock Brake System, Electronic
Suspension Control, Adaptive
Forward Lighting System (AFS)
2 Horn
3Adaptive Cruise Control (ACC),
Transmission Controls
6-87