wheel CADILLAC XT4 2023 Owners Manual
[x] Cancel search | Manufacturer: CADILLAC, Model Year: 2023, Model line: XT4, Model: CADILLAC XT4 2023Pages: 476, PDF Size: 5.37 MB
Page 393 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
392 Vehicle Care
7. Pressure Deflation Button
8. Pressure Gauge
9. Power Plug
10.Air Only Hose
Tire Sealant
Read and follow the safe
handling instructions on the
label adhered to the tire
sealant canister (4).
Check the tire sealant
expiration date on the tire
sealant canister. The tire
sealant canister (4) should be
replaced before its expiration date. Replacement tire sealant
canisters are available at your
local dealer.
There is only enough sealant
to seal one tire. After usage,
the tire sealant canister must
be replaced.
Using the Tire Sealant and
Compressor Kit to
Temporarily Seal and
Inflate a Punctured Tire
When using the tire sealant
and compressor kit during cold
temperatures, warm the kit in
a heated environment for
five minutes. This will help to
inflate the tire faster.
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers
0152.
See If a Tire Goes Flat 0389
for other important safety
warnings. Do not remove any objects
that have penetrated the tire.
1. Remove the tire sealant canister (4) and
compressor from its
storage location. See
Storing the Tire Sealant
and Compressor Kit 0398.
2. Remove the air only hose (10) and the power plug (9)
from the bottom of the
compressor.
3. Place the compressor on the ground near the
flat tire.
Page 396 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
Vehicle Care 395
20. If the flat tire was able toinflate to the
recommended inflation
pressure, remove the
maximum speed label from
the sealant canister and
place it in a highly visible
location.
Do not exceed the speed
on this label until the
damaged tire is repaired or
replaced.
21. Return the equipment to its original storage location
in the vehicle.
22. Immediately drive the vehicle 8 km (5 mi) to
distribute the sealant in
the tire. 23. Stop at a safe location and
check the tire pressure.
Refer to Steps 1–10 under
“Using the Tire Sealant and
Compressor Kit without
Sealant to Inflate a Tire
(Not Punctured).”
If the tire pressure has
fallen more than 68 kPa
(10 psi) below the
recommended inflation
pressure, stop driving the
vehicle. The tire is too
severely damaged and the
tire sealant cannot seal the
tire. See Roadside
Assistance Program 0439.
If the tire pressure has not
dropped more than 68 kPa
(10 psi) from the
recommended inflation
pressure, inflate the tire to
the recommended inflation
pressure. 24. Wipe off any sealant from
the wheel, tire, or vehicle.
25. Dispose of the used tire sealant canister (4) at a
local dealer or in
accordance with local
state codes and practices.
26. Replace it with a new canister available from
your dealer.
27. After temporarily sealing a tire using the tire sealant
and compressor kit, take
the vehicle to an
authorized dealer within
161 km (100 mi) of driving
to have the tire repaired or
replaced.
Page 397 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
396 Vehicle Care
Using the Tire Sealant and
Compressor Kit without
Sealant to Inflate a Tire
(Not Punctured)
The kit includes:
1. Sealant Canister InletValve
2. Sealant/Air Hose
3. Base of Sealant Canister
4. Tire Sealant Canister
5. On/Off Button
6. Slot on Top of Compressor
7. Pressure Deflation Button
8. Pressure Gauge
9. Power Plug
10. Air Only Hose
If a tire goes flat, avoid further
tire and wheel damage by
driving slowly to a level place.
Turn on the hazard warning
flashers. See Hazard Warning
Flashers 0152.
See If a Tire Goes Flat 0389
for other important safety
warnings.
1. Remove the compressor from its storage location.
See Storing the Tire
Sealant and Compressor
Kit 0398. 2. Remove the air only hose
(10) and the power plug (9)
from the bottom of the
compressor.
3. Place the compressor on the ground near the
flat tire.
Make sure the tire valve
stem is positioned close to
the ground so the hose will
reach it.
4. Remove the valve stem cap from the flat tire by
turning it
counterclockwise.
5. Attach the air only hose (10) to the tire valve stem
by turning it clockwise until
tight.
6. Plug the power plug (9) into the accessory power
outlet in the vehicle.
Unplug all items from other
accessory power outlets.
See Power Outlets 0115.
If the vehicle has an
accessory power outlet, do
not use the cigarette
lighter.
Page 400 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
Vehicle Care 399
4. Turn the retainer nutcounterclockwise and
remove the spare tire.
Place the spare tire next
to the tire being changed.
5. The jack and tools are stored below the
spare tire.
Remove them from their
container and place them
near the tire being
changed.
Removing the Flat Tire
and Installing the
Spare Tire
1. Do a safety check beforeproceeding. See If a Tire
Goes Flat 0389.
2. For vehicles equipped with a wheel cover or center
cap, pull the cover or
center cap away from the
wheel to remove it.
Store the wheel cover in
the cargo area until the flat
tire is repaired or replaced.
If the vehicle has a center
cap with wheel nut caps,
the wheel nut caps are
designed to stay with the
center cap after they are
loosened.
Remove the entire center
cap if the wheel has a
smooth center cap. Place
the chisel end of the wheel
wrench in the slot on the
wheel, and gently pry it off.
3. Turn the wheel wrenchcounterclockwise to loosen
all the wheel nuts, but do
not remove them yet.
Caution
Make sure that the jack lift
head is in the correct
position or you may damage
your vehicle. The repairs
would not be covered by
your warranty.
4. Position the jack lift head at the jack location nearest
the flat tire.
Page 402 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
Vehicle Care 401
5. Turn the wheel wrenchclockwise to raise the jack
until the slot in the jack lift
head fits into the metal
flange located behind the
cut out on the plastic
molding.
Do not raise the
vehicle yet.
6. Put the compact spare tire near you.
7. Raise the vehicle by turning the jack handle
clockwise. Raise the
vehicle far enough off the ground so there is enough
room for the road tire to
clear the ground.
8. Remove all of the
wheel nuts.
9. Remove the flat tire.
{Warning
Rust or dirt on a wheel,
or on the parts to which it
is fastened, can cause
wheel nuts to become
loose over time. The
wheel could come off and
(Continued)
Warning (Continued)
cause a crash. When
changing a wheel, remove
any rust or dirt from
places where the wheel
attaches to the vehicle. In
an emergency, a cloth or
paper towel can be used;
however, use a scraper
or wire brush later to
remove all rust or dirt.
Page 403 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
402 Vehicle Care
10. Remove any rust or dirtfrom the wheel bolts,
mounting surfaces, and
spare wheel.
11. Place the compact spare tire on the wheel-mounting
surface.
{Warning
Never use oil or grease on
bolts or nuts because the
nuts might come loose. The
vehicle's wheel could fall off,
causing a crash.
12. Reinstall the wheel nuts. Tighten each nut by hand
until the wheel is held
against the hub.
13. Lower the vehicle by turning the jack handle
counterclockwise.
{Warning
Wheel nuts that are
improperly or incorrectly
tightened can cause the
(Continued)
Warning (Continued)
wheels to become loose or
come off. The wheel nuts
should be tightened with a
torque wrench to the proper
torque specification after
replacing. Follow the torque
specification supplied by the
aftermarket manufacturer
when using accessory
locking wheel nuts. See
Capacities and
Specifications0433 for
original equipment wheel nut
torque specifications.
Caution
Improperly tightened wheel
nuts can lead to brake
pulsation and rotor damage.
To avoid expensive brake
repairs, evenly tighten the
wheel nuts in the proper
sequence and to the proper (Continued)
Caution (Continued)
torque specification. See
Capacities and
Specifications0433 for the
wheel nut torque
specification.
14. Tighten the wheel nuts firmly in a crisscross
sequence, as shown.
15. Lower the jack all the way and remove the jack from
under the vehicle.
16. Tighten the wheel nuts firmly with the wheel
wrench.
Page 404 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
Vehicle Care 403
When reinstalling the wheel
cover or center cap on the
full-size tire, tighten all five
plastic caps hand snug with
the aid of the wheel wrench
and tighten them with the
wheel wrench an additional
one-quarter of a turn.
Caution
Wheel covers will not fit on
the vehicle's compact spare.
If you try to put a wheel
cover on the compact spare,
the cover or the spare could
be damaged.
Storing a Flat or Spare
Tire and Tools
{Warning
Storing a jack, a tire,
or other equipment in the
passenger compartment of
the vehicle could cause
injury. In a sudden stop or(Continued)
Warning (Continued)
collision, loose equipment
could strike someone. Store
all these in the proper place.
To store the flat or spare tire
and tools: 1. Open the liftgate. See Liftgate 024.
2. Replace the jack and tools in their original storage
location.
3. Lower the load floor.
4. Place the tire, lying flat, in the rear storage
compartment.
5. Place the loop end of the strap through the liftgate
striker.
6. Route the strap throughthe wheel as shown.
7. Attach the hook to the loop end of the strap.
8. Tighten the strap.
9. Replace the cargo cover, if equipped.
10. Close the liftgate and make sure it is fully
latched.
The compact spare is for
temporary use only. Replace
the compact spare tire with a
full-size tire as soon as
you can.
Page 405 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
404 Vehicle Care
Compact Spare Tire
{Warning
Driving with more than one
compact spare tire at a time
could result in loss of
braking and handling. This
could lead to a crash and
you or others could be
injured. Use only one
compact spare tire at a time.
If this vehicle has a compact
spare tire, it was fully inflated
when new; however, it can
lose air over time. Check the
inflation pressure regularly.
It should be 420 kPa (60 psi).
Stop as soon as possible and
check that the spare tire is
correctly inflated after being
installed on the vehicle. The
compact spare tire is designed
for temporary use only. The
vehicle will perform differently
with the spare tire installed
and it is recommended that
the vehicle speed be limited to
80 km/h (50 mph). To conserve the tread of the spare tire,
have the standard tire
repaired or replaced as soon
as convenient and return the
spare tire to the storage area.
When using a compact spare
tire, the AWD (if equipped),
ABS, and Traction Control
systems may engage until the
spare tire is recognized by the
vehicle, especially on slippery
roads. Adjust driving to reduce
possible wheel slip.
Caution
When the compact spare is
installed, do not take the
vehicle through an
automatic car wash with
guide rails. The compact
spare can get caught on the
rails which can damage the
tire, wheel, and other parts
of the vehicle.
Do not use the compact spare
on other vehicles. Do not mix the compact spare
tire or wheel with other
wheels or tires. They will not
fit. Keep the spare tire and its
wheel together.
Caution
Tire chains will not fit the
compact spare. Using them
can damage the vehicle and
the chains. Do not use tire
chains on the compact
spare.
Jump Starting
Jump Starting - North
America
For more information about
the vehicle battery, see
Battery - North America
0346.
If the battery has run down,
try to use another vehicle and
some jumper cables to start
your vehicle. Be sure to use
the following steps to do it
safely.
Page 410 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
Vehicle Care 409
Front Attachment Points
The vehicle is equipped with
specific attachment points to
be used by the towing
provider. These holes may be
used to pull the vehicle from a
flat road surface onto the
flatbed tow truck.
Recreational Vehicle
Towing
Recreational vehicle towing
means towing the vehicle
behind another vehicle, such
as behind a motor home. The
two most common types ofrecreational vehicle towing are
known as dinghy towing and
dolly towing. Dinghy towing is
towing the vehicle with all four
wheels on the ground. Dolly
towing is towing the vehicle
with two wheels on the
ground and two wheels up on
a device known as a dolly.
Here are some important
things to consider before
recreational vehicle towing:
.Become familiar with the
local laws that apply to
recreational vehicle towing.
These laws may vary by
region.
.The towing capacity of the
towing vehicle. Be sure to
read the tow vehicle
manufacturer's
recommendations.
.How far the vehicle will be
towed. Some vehicles have
restrictions on how far and
how long they can be towed.
.The proper towing
equipment. See your dealer
or trailering professional foradditional advice and
equipment
recommendations.
.If the vehicle is ready to be
towed. Just as preparing the
vehicle for a long trip, make
sure the vehicle is prepared
to be towed.
Caution
Use of a shield mounted in
front of the vehicle grille
could restrict airflow and
cause damage to the
transmission. The repairs
would not be covered by the
vehicle warranty. If using a
shield, only use one that
attaches to the towing
vehicle.
Page 411 of 476

Cadillac XT4 Owner Manual (GMNA-Localizing-U.S./Canada/Mexico-
16412876) - 2023 - CRC - 3/25/22
410 Vehicle Care
Dinghy Towing
Caution
If the vehicle is towed with
all four wheels on the
ground, the drivetrain
components could be
damaged. The repairs would
not be covered by the
vehicle warranty. Do not tow
the vehicle with all four
wheels on the ground.
The vehicle is neither designed
nor intended to be towed with
all four wheels on the ground.
If the vehicle must be towed, a dolly should be used. See the
following information on dolly
towing.
Dolly Towing
Loading up to the Dolly
1. On level ground start the engine.
2. Release the park brake.
3. Apply the brake pedal and hold until the end of step 5.
4. Push and hold the Electric Parking Brake (EPB)
switch. After 15 seconds, the EPB amber telltale will
begin flashing in the IP
cluster.
5. When the indicator flashes amber, release the EPB
within five seconds. Then,
push and release the EPB
switch and release the
brake pedal.
6. The EPB amber telltale will remain flashing and
parking brake will be
released if process is
successful.
7. Put the front wheels on the dolly.
8. Shift the transmission to P (Park).
9. Turn the vehicle off.
10. Secure the vehicle to the dolly.
11. Follow the dolly manufacturer's
instructions for preparing
the vehicle and dolly for
towing.
12. Open the hood.