lock CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine SEATS
General Information
Description
The seat movement is controlled by an adjustment bar. The seat can be adjusted to six different seating positions.
The vehicle may be equipped with heated seats. Heated seats provide comfort and warmth in cold weather. The
heaters provide the same heat level for both the seat cushion and back. The driver seat and front passenger seat are
heated.
Operation
The manual seat adjustment bar is at the front of the seat, near the floor. Pull the bar upward and slide the seat
forward or rearward. Release the bar once the seat is in the desired position. To confirm the seat is locked into place,
attempt to move the seat forward and rearward after adjusting the seat. The heated seat controls for each seat are
located near the bottom center of the instrument panel. After turning the ignition ON, the seat heater can be activated
to High or Low heat settings. When the switch is in the middle position, the seat heater is OFF. Each switch is
equipped with LED lights to indicate the level of heat at which each seat is set.
15–104Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3. Press the seat latch rod to separate the back ofthe seat from the clamp rod.
4. Pull up the seat strap behind the seat and unlock the latch in front of the seat.
5. Installation is in the reverse order of removal.
SEATS
LTSM150068
15–108Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Remote Keyless Entry (RKE) Inoperative
No Response From Remote Keyless Entry (RKE) Transmitter
1.CHECK BATTERY
• Check battery of the RKE transmitter.
Is the battery voltage of the RKE transmitter normal?
Ye s>>Go to the next step.
No
>>This concern has been caused by the transmitter battery.
Go to step 4.
2.CHECK THE IGNITION LOCK CYLINDER CONDITION
• Check the ignition lock cylinder for proper operation.
Is the check result normal?
Ye s>>Go to the next step.
No
>>Repair or replace the ignition lock cylinder key switch.
3.PERFORM THE RKE TRANSMITTER MATCH PROCEDURE
• Close all the doors.
• Insert the ignition key into the ignition switch which has lost synchronization in LOCK position.
• Press any button on the RKE transmitter within 5 seconds.
• Pull the ignition key out of the ignition switch.
• Try to operate the RKE transmitter.
Does the RKE transmitter operate properly?
Ye s>>Erase all codes before returning the vehicle to the customer.
No
>>Go to the next step.
DIAGNOSIS & TESTING
15
15–11 5Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 4.PERFORM THE RKE TRANSMITTER MATCH WITH THE X-431
• Replace the RKE transmitter.
• Connect the X-431 scan tool to the Data Link Connector (DLC), press the POWER key to start the X-431 (use
the most current software available).
• Turn ignition switch on.
Enter the Diagnostic Program.
Select Chery main program.
Select diagnostic version.
Enter download program.
Select T11 series, and then select ISU.
Select Remoter Match.
• Press the lock button on the RKE transmitter for less than 2 seconds.
• Pull out the ignition switch.
• Try to operate the RKE transmitter.
Does the RKE transmitter operate properly?
Ye s>>Erase all codes before returning the vehicle to the customer.
The concern was caused by the RKE transmitter.
No
>>Replace the FBCM (See FBCM Removal & Installation in Section 15 Body & Accessories).
Refer to the RKE transmitter match procedure with X-431 as the description.
Perform match between the RKE transmitter and FBCM with X-431.
DIAGNOSIS & TESTING
LTSMD150020T
15–11 6Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 13. Temporarily connect the power window switch.
14. Turn the ignition switch on and use the power window switch to move the front door glass to a position so thedoor glass bolts can be removed.
15. Turn the ignition switch off and disconnect the power window switch.
16. Remove the two door glass mounting bolts (1). (Tighten: Door glass mounting bolts to 11 N·m)
NOTE: Properly support the door glass when
removing the mounting bolts. The door glass may
drop and be damaged.
17. Remove the door glass weatherstrip (1).
18. Lift the door glass and remove the door glass from the door.
NOTE: Take care not to damage the door glass.
19. Disconnect the power window motor electrical con- nector.
20. Remove the six power window regulator mounting bolts (1).
(Tighten: Power window regulator mounting bolts to
11 N·m)
21. Carefully remove the power window regulator.
22. Remove the power window motor from the regulator.
23. Remove three door lock assembly retaining bolts. (Tighten: Door lock assembly retaining bolts to9±1N·m)
DOORS
LTSM150116
LTSM150137 LTSM150117
15–170Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 24. Remove the internal unlock cable (1) and lockcable (2).
25. Remove the lock buckle with screwdriver. (Tighten: Lock buckle screws to 12 ± 2 N·m)
26. Remove the front door outside handle.
27. Remove the front door panel and then the protec- tive film.
28. Pry up on the cover (1) of the outside handle.
29. Remove the mounting bolts with hexagon spline wrench.
DOORS
LTSM150098
LTSM150114
15
15–171Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 30. Detach the lock from the linkage rod, remove thelock and the cover of left front door.
31. Remove the outside handle.
Assembly
Assemble is in the reverse order of disassembly
Front Door Adjustment
1. Adjust the door gap with a spacer gauge. •The gap of the upper section between the front door and the back door should be 5.5 ± 0.7 mm
• The gap of the outboard side should be 5.5 ± 0.7 mm
• The gap between the front door and pole A should be 6.5±1mm
• The gap of upper section between front door and back door should be 5.5 ± 0.7 mm
• The gap between the front/back door and the doorsill should be6±1mm
• The overall levelness when measured with a magnet should be 0-0.5 mm
2. Install the bolts (Part Number: T11-6101103, 2 pcs both upper and lower) into the body for 2-3 turns, tighten with pneumatic wrench. Torque: 35 ± 3 N·m.
Check for the following after repair:
• Any scratches from reassembly
• Whether the bolts and nuts are assembled properly
• Whether the bolts and nuts are properly tightened
• Whether the gap and levelness between front door and back door is within the specifications
• Whether the edge height is 0-0.5 mm.
Replacing Front Door Hinge
1. Remove the front fender to gain access to the door hinge (See Fender Removal & Installation in Section 15
Body & Accessories).
2. Support the door.
3. Remove the four retaining bolts from the upper and lower hinges, and then remove the hinges.
DOORS
LTSM150120
15–172Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 8. Remove the mounting bolts (1) from the windowregulator.
9. Remove the lock mounting screws with an internal spline socket.
10. Loosen the pull rod from the door handle, pull out the electrical harness, and then remove the lock.
11. Remove the rear door outside handle. •Remove the mounting bolts of the handle seat
with hexagon spline wrench from one side of
the shield.
12. Remove the handle seat. •Remove the outside handle.
13. Remove the weather strip from the door opening.
14. Disconnect the inner harness of the door from out- side.
Assembly
Assemble in the reverse order of disassembly.
Rear Door Adjustment
1. Adjust the door gap with a spacer gauge.•The gap between the rear door and the trian-
gle window should be 8 ± 1.5 mm
• The gap between the rear door and the side
fender should be6±1mm
• The gap between the rear door and the door-
sill should be6±1mm
• The overall levelness when measured with a
magnet should be 0-0.5 mm as shown by the
arrow
2. Install the nuts (Part Number: Q32008, 2 pcs both upper and lower) into the body for 2-3 turns,
tighten with pneumatic wrench. Torque: 35 ± 3
N·m.
Check for the following after repair:
• Any scratches from reassembly
• Whether the bolts and nuts are assembled properly
• Whether the bolts and nuts are properly tightened
• Whether the gap between rear door and side fender and the levelness are within the specifications
• Whether the edge of back door is 0-0.5 mm higher than the side fender.
DOORS
LTSM150118
LTSM150119
15–174Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 6. Remove the rod from the door handle from thedoor lock body, remove the outer handle of back
cargo door.
7. Remove the back cargo door lock.
8. Pull out the connector for the wiring harness.
9. Remove the lock.
10. Remove the high mounted stop lamp assembly (1).
11. Remove the rear fog lamp assembly.
12. Remove the spare tire support.
DOORS
LTSM150122
LTSM150123
15–176Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Front Windshield
Removal
1. Remove the wiper arms and the lower trim panel from the windshield (See Wiper Arm Removal & Installation inSection 15 Body & Accessories).
2. Using piano wire, insert the piano wire between the body and the glass. Attach wooden blocks to both
ends of the piano wire.
CAUTION:
To prevent vehicle paint damage, use adhesive
tape on painted surfaces during windshield
removal. Place a plastic cover between the
piano wire and the instrument panel to prevent
the instrument panel from being scuffed when
removing the glass.
3. Pull the piano wire around the glass, and cut offthe bonding agent to remove the glass.
NOTE :
Leave as much bonding agent as possible on the body
when removing the bonding portion of the glass.
Installation
1. Remove the rough portions on the body with a knife and clean the cut bonding agent with a rag soaked with cleaning solvent.
CAUTION:
Even if the entire bonding agent has been cleared, you should also clean the body surface. Do not
touch the glass surface after cleaning.
2. Remove the stopper with a knife.
3. Clear the bonding agent adhered to the glass with a scraper and clean the glass with glass cleaner.
NOTE :
Do not touch the glass after cleaning.
STATIONARY GLASS
BESM150013
BESM150014
15
15–219Chery Automobile Co., Ltd.