belt CHERY TIGGO 2009 Service Owner's Manual

Downloaded from www.Manualslib.com manuals search engine 13. Remove the fuel rail bracket bolts (1).(Tighten: Fuel rail bracket bolts to 11 N·m)
14. Remove the fuel rail with the fuel injectors and set aside.
15. Remove the screws securing the vacuum valve bracket to the intake manifold.
16. Set aside the vacuum valve and pipe.
17. Disconnect intake manifold electrical harness, and vacuum hose.
18. Remove the bolts (2) & (3) securing the engine oil dipstick to intake manifold. Remove the dipstick.
(Tighten: Dipstick bracket bolts to 11 N·m)
19. Disconnect the oil pressure switch connect (4).
20. Remove the nuts (1) securing the intake manifold to cylinder head.
(Tighten: Intake manifold nuts to 11 N·m)
21. Installation is in the reverse order of removal.
Installation Notes:
• Clean all surfaces of manifold and cylinder head.
• Install a new intake manifold gasket during installation.
• Install new O-rings on the fuel injectors.
Idler Pulley
Removal & Installation
1. While using a suitable tool and securely holding the hexagonal portion of the drive belt tensioner, rotate the
pulley counterclockwise to loosen the drive belt.
WARNING!
Avoid placing hands near the drive belt tensioner while it is being held.
ON-VEHICLE SERVICE
LTSM020222
LTSM020223
02
02–45Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2. Remove the drive belt.
Upper Accessory Drive Belt Idler Pulley (1)
• Remove the bolt and the upper accessory drive
belt idler pulley.
(Tighten: Upper idler pulley bolt to 45 N·m)
Lower Accessory Drive Belt Idler Pulley (2)
• Remove the bolt and the lower accessory drive belt
idler pulley.
(Tighten: Lower idler pulley bolt to 45 N·m) 3. Installation is in the reverse order of removal.
Oil Filter
Removal & Installation
NOTE :
The following special tools are required to perform the repair procedure:
• CH-10003 - Oil Filter Remover
WARNING!
Prolonged and repeated contact with engine oil will harm your skin. If engine oil is spilled on your skin, wash it
off immediately with water. In addition, used engine oil contains potentially harmful contaminants which may
cause skin cancer. Always use adequate skin protection when performing vehicle service.
CAUTION:
When servicing the oil filter, install the special tool against the base of the filter to avoid deforming
the filter.
1. Using special tool CH-10003 oil filter remover,
remove the oil filter (1).
(Tighten: Oil filter to 25 N·m)
CAUTION: When removing the oil filter, ensure
that the oil filter gasket is not stuck to the
engine. The oil filter gasket must be removed
from the engine before installing the new oil
filter.
2. Installation is in the reverse order of removal.
Installation Notes:
• Clean the surface, and verify the oil filter does not leak.
ON-VEHICLE SERVICE
LTSM020203
LTSM020206
02–46Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Oil Pump
Removal & Installation
1. Remove the accessory drive belt (See Accessory Drive Belt Removal & Installation in Section 02 Engine).
2. Remove the crankshaft vibration damper retainingbolts (1).
(Tighten: Crankshaft vibration damper bolts to 25
N·m)
3. Remove the engine timing belt (See Engine Timing Belt Removal & Installation in Section 02 Engine).
4. Remove the crankshaft timing belt pulley bolt (2) from the crankshaft.
(Tighten: Crankshaft timing belt pulley bolt to 130
N·m and an additional 65°)
5. Remove the key-way from the crankshaft.
6. Using an appropriate tool, remove the front crank- shaft oil seal (1).
7. Remove the four oil pump bolts (1). (Tighten: Oil pump bolts to 11 N·m)
8. Remove the oil pump (2) using a suitable tool.
9. Remove the oil pump gasket (3).
10. Installation is in the reverse order of removal.
Installation Notes:
• Before installing, prime the new oil pump. Fill the oil pump with engine oil and rotate the oil pump.
• Replace the oil pump gasket.
ON-VEHICLE SERVICE
BESM020055
LTSM020199
BESM020032
02–48Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 2.0L ENGINE MECHANICAL
GENERAL INFORMATION02-77
Description 02-77
Operation 02-77
Specifications 02-77
Special Tools 02-81
Lubrication System 02-84
DIAGNOSIS & TESTING02-87
Engine Performance Diagnostics 02-87
Engine Mechanical Diagnostics 02-88
Cylinder Compression Pressure Test 02-90
Cylinder Head Gasket Test 02-90
ON-VEHICLE SERVICE02-91
Accessory Drive Belt 02-91
Removal & Installation 02-91
Air Cleaner Element 02-92
Removal & Installation 02-92
Air Cleaner Housing 02-93
Removal & Installation 02-93
Cylinder Head Cover 02-93
Removal & Installation 02-93
Camshaft 02-94
Removal & Installation 02-94
Cylinder Head 02-97
Removal & Installation 02-97
Front Crankshaft Oil Seal 02-99
Removal & Installation 02-99
Rear Crankshaft Oil Seal 02-100
Removal & Installation 02-100
Engine Mounts 02-103
Removal & Installation - Left Mount 02-103
Removal & Installation - Right Mount 02-104
Removal & Installation - Front Mount 02-104
Removal & Installation - Rear Mount 02-105
Engine Assembly 02-105
Removal & Installation 02-105
Engine Timing Belt 02-112
Removal & Installation 02-112
Exhaust Manifold 02-115
Removal & Installation 02-115
Intake Manifold 02-117
Removal & Installation 02-117
Idler Pulley 02-119
Removal & Installation 02-119
Oil Filter 02-119
Removal & Installation 02-119Oil Pan
02-120
Removal & Installation 02-120
Oil Pump 02-121
Removal & Installation 02-121
Oil Strainer 02-122
Removal & Installation 02-122
ENGINE UNIT REPAIR02-123
Engine Block 02-123
Specifications 02-123
Disassembly 02-123
Inspection 02-125
Assembly 02-125
Pistons 02-126
Specifications 02-126
Disassembly 02-127
Inspection 02-128
Assembly 02-130
Connecting Rods 02-131
Specifications 02-131
Disassembly 02-131
Inspection 02-132
Assembly 02-132
Crankshaft 02-133
Specifications 02-133
Disassembly 02-133
Inspection 02-134
Assembly 02-135
CYLINDER HEAD UNIT REPAIR02-136
Cylinder Head 02-136
Specifications 02-136
Disassembly 02-136
Inspection 02-138
Assembly 02-138
Camshaft 02-139
Specifications 02-139
Disassembly 02-140
Inspection 02-140
Assembly 02-142
Valve & Valve Guides 02-143
Specifications 02-143
Disassembly 02-143
Inspection 02-144
Assembly 02-145
Valve Springs 02-146
Specifications 02-146
Disassembly 02-146
Inspection 02-147
Assembly 02-148
02–76Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
The 2.0L in-line four cylinder engine has the following features:
•Dual overhead camshafts
• Four valves per cylinder
• Aluminum cylinder head
• Aluminum cylinder block
Operation
The 2.0L engine utilizes 4 valve-per-cylinders and a dual overhead camshaft design. The engine uses an individual
coil ignition system. The cylinder block is made of aluminum and the bearing caps are integrated into the lower cyl-
inder block assembly. An aluminum oil pan bolts to the bottom of the lower cylinder block. The camshafts are
mounted in the cylinder head and act against valve tappets to open and close the valves. The camshafts are driven
off the front of the cylinder head by one timing belt. The belt is driven by a sprocket that is located on the crankshaft.
The piston assembly is an aluminum piston with a cast iron connecting rod.
The aluminum cylinder head contains dual overhead camshafts with 4 valve-per-cylinder construction. The valves are
arranged in two in-line banks. The cylinder head incorporates powdered metal valve guides and seats. The cylinder
head is sealed to the block using a multi-layer steel head gasket and retaining bolts.
Specifications
2.0L Engine Specifications
DESCRIPTION SPECIFICATION
Type In-Line OHV, DOHC
Number of Cylinders 4
Compression Ratio 10:1
Compression Pressure 10 - 15 bar
Max. Compression Pressure Variation Between
Cylinders 25%
Stroke 90 mm
Bore 83.5 mm
Displacement 1971 cc
Firing Order 1-3-4-2
Mechanical Specifications
DESCRIPTIONITEMSTANDARD LIMIT
Engine Oil Pressure Lower Idle Speed (800 ±
50 RPM) 1.2 - 1.5 bar
-
High Idle Speed (2000 RPM) 3.2 - 3.5 bar
-
High Speed (4000 RPM) 3.7 ± 0.5 bar -
Engine Block Clearance Surface Distortion
-0.15 mm
Inner Diameter 83.500 - 83.510 mm -
Out-Of-Round -< 0.008 mm
Taper -< 0.01 mm
Piston Ring Groove
Clearance First Ring
0.04 - 0.08 mm -
Second Ring 0.0251 - 0.01 mm -
02
02–77Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DESCRIPTIONITEMSTANDARD LIMIT
Intake Camshaft Axial
Clearance -
0.15 - 0.20 mm -
Exhaust Camshaft Axial
Clearance -
0.15 - 0.20 mm -
Intake Valve Guide
Clearance -
0.012 - 0.043 mm -
Exhaust Valve Guide
Clearance -
0.032 - 0.063 mm -
Valve Outer Diameter Intake Valve
5.98 ± 0.008 mm -
Exhaust Valve 5.96 ± 0.008 mm -
Valve Guide Inner
Diameter Intake Valve
5.4 ± 0.1 mm -
Exhaust Valve 5.4 ± 0.1 mm -
Fringe Thickness On Top
Of Valve Intake Valve
0.3 ± 0.15 mm -
Exhaust Valve 0.3 ± 0.15 mm -
Valve Tilt Angle Intake Valve
65°-
Exhaust Valve 68°-
Valve Height Intake Valve
107.998 mm -
Exhaust Valve 106.318 mm -
Torque Specifications
CAUTION:
When torquing a fastener in two steps, DO NOT use a torque wrench for the second step.
DESCRIPTION TORQUE (N·m)
Accessory Drive Belt Tensioner Pulley Bolt 35
Camshaft Bearing Cap Bolts 11
Clutch Pressure Plate Bolts 25
Connecting Rod Cap Bolts 1st Step: Tighten the bolt to 25 N·m
2nd Step: Tighten the bolt an additional 90°
Crankshaft Holder 28
Crankshaft Main Bearing Cap Bolts 1st Step: Tighten the bolt to 45 N·m
2nd Step: Tighten the bolt an additional 180°
Crankshaft Timing Belt Pulley Bolt 1st Step: Tighten the bolt to 130 N·m
2nd Step: Tighten the bolt an additional 65°
Crankshaft Vibration Damper Bolts 25
Cylinder Head Cover Bolts 11
Cylinder Head Bolts 1st Step: Tighten the bolt to 40 ± 5 N·m
2nd Step: Tighten the bolt an additional 90 ± 5° 3rd Step: Tighten the bolt an additional 90 ± 5°
Dipstick Bracket Bolts 11
Drive Plate Bolts (automatic transaxle) 75
Engine Left Mount Bolt 70
Engine Right Mount Bolt 70
Engine Front Mount Bolt 60
Engine Rear Mount Bolt 60
GENERAL INFORMATION
02
02–79Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DESCRIPTIONTORQUE (N·m)
Engine To Transaxle Bolts 80
Exhaust Manifold Nuts 25
Exhaust Manifold Heat Shield Bolts 15
Exhaust Camshaft Timing Belt Pulley Bolt 120
Flywheel Bolts (manual transaxle) 75
Fuel Rail Bracket Bolts 11
Idler Pulley Bolt 40
Intake Camshaft Timing Belt Pulley Bolt 120
Intake Manifold Bolts 10
Intake Manifold Nuts 11
Intake Manifold Bracket Bolts 25
Lower Idler Pulley Bolt 45
Lower Cylinder Block Bolts 23
Oil Filter 25
Oil Pan Bolts 18
Oil Drain Plug 40
Oil Strainer Bolts 18
Oil Pump Bolts 11
(Apply with Loctite 5910 Thread-Locker)
Rear Timing Cover Bolts 7
Timing Belt Upper Cover Bolts 11
Timing Belt Lower Cover Bolts 11
Timing Belt Tensioner Assembly 27
Timing Belt Tensioner Pulley Bolt 30
Throttle Body Bolts 11
Upper Idler Pulley Bolt 45
GENERAL INFORMATION
02–80Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Valve Stem Seal Installer GuideCH-20012
Valve Seal RemoverCH-20013
Valve Keeper Installer CH-20017
Valve Spring Compressor CH-20018
Crankshaft Belt Pulley Fixture CH-20019
GENERAL INFORMATION
02
02–83Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DIAGNOSIS & TESTING
Engine Performance Diagnostics
CONDITIONPOSSIBLE CAUSE CORRECTION
Engine Does Not Start 1. Weak battery.
2. Corroded or loose battery
connections.
3. Faulty starter.
4. Faulty coil(s) or control unit.
5. Incorrect spark plug gap.
6. Contamination in fuel system.
7. Faulty fuel pump.
8. Incorrect timing.1. Test battery. Charge or replace if
necessary.
2. Clean and tighten battery
connections. Apply a coat of light
mineral grease to terminals.
3. Test starting system. Check for
codes. (Refer to Appropriate
Diagnostic Information)
4. Test and replace as needed.
(Refer to Appropriate Diagnostic
Information)
5. Set gap.
6. Clean system and replace fuel
filter.
7. Test fuel pump and replace as
needed. (Refer to Appropriate
Diagnostic Information)
8. Check for a skipped timing belt.
Engine Stalls Or Idles Rough 1. Idle speed too low.
2. Incorrect fuel mixture.
3. Intake manifold leakage.
4. Faulty ignition coil(s).1. Test minimum air flow. (Refer to
Appropriate Diagnostic Information)
2. (Refer to Appropriate Diagnostic
Information)
3. Inspect intake manifold, manifold
gasket, and vacuum hoses.
4. Test and replace if necessary.
(Refer to Appropriate Diagnostic
Information)
Engine Loss Of Power 1. Dirty or incorrectly gapped spark
plugs.
2. Contamination in fuel system.
3. Faulty fuel pump.
4. Incorrect valve timing.
5. Leaking cylinder head gasket.
6. Low compression.
7. Burned, warped, excessive
clearance, or pitted valves.
8. Plugged or restricted exhaust
system.
9. Faulty ignition coil(s).
10. Burned spark plugs.1. Clean spark plugs and set gap.
2. Clean system and replace fuel
filter.
3. Test and replace if necessary.
(Refer to Appropriate Diagnostic
Information)
4. Correct valve timing.
5. Replace cylinder head gasket.
6. Test compression of each
cylinder.
7. Replace valves.
8. Perform exhaust restriction test.
Install new parts.
9. Test and replace if necessary.
(Refer to Appropriate Diagnostic
Information)
10. Replace spark plugs.
DIAGNOSIS & TESTING
02
02–87Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine ON-VEHICLE SERVICE
Accessory Drive Belt
Removal & Installation
WARNING!
Inspect the drive belt only when the engine is stopped.
1. While using a suitable tool and securely holding the hexagonal portion of the drive belt tensioner, rotate thepulley counterclockwise to loosen the drive belt.
WARNING!
Avoid placing hands near the drive belt tensioner while it is being held.
1 - Drive Belt
2 - Generator Bolt
3 - Tensioner Pulley Bolt
4 - Tensioner
5 - Compressor
6 - Generator
7 - Idler Pulley
8 - Generator Bracket
9 - Generator Bracket Bolt10 - Generator Bracket Bolt
11 - Power Steering Pump Bolt
12 - Power Steering Pump Bolt
13 - Power Steering Pump Bolt
14 - Power Steering Pump Bracket
15 - Power Steering Pump Bracket Bolt
16 - Power Steering Pump
17 - Idler Pulley
18 - Compressor Bolt
LTSM020163
02
02–91Chery Automobile Co., Ltd.