lock CHERY TIGGO 2009 Service Manual Online

Downloaded from www.Manualslib.com manuals search engine TRANSAXLE & TRANSFER CASE
08
CONTENTSpage
DP0 Automatic Transaxle .............................................................. 08-1
F4A4 Automatic Transaxle ........................................................... 08-143
5-Speed Manual Transaxle ........................................................... 08-246
Front Differential ................................................................... 08-307
Clutch System ..................................................................... 08-316
Transfer Case (4x4) ................................................................. 08-326
DP0 AUTOMATIC TRANSAXLE
GENERAL INFORMATION08-3
Description 08-3
Operation 08-6
Specifications 08-7
Special Tools 08-8
Electrical Schematics 08-10
DP0 Transaxle Control Module (TCM)
Connector Pin-Out Table 08-18
DIAGNOSIS & TESTING08-19
Diagnostic Help 08-19
Intermittent DTC Troubleshooting 08-19
Ground Inspection 08-19
Diagnostic Tools 08-19
Diagnostic Trouble Code (DTC) List 08-20
DP0 Automatic Transaxle DTC List 08-20
Diagnostic Trouble Code (DTC) Tests 08-22
P0641 - Sensor Feed 08-22
P0657 - Solenoid Power Supply Circuit
Shorted To Voltage 08-28
P0657 - Solenoid Power Supply Circuit
Open 08-32
P0705 - Multi-Function Switch:
Prohibited Position 08-37
P0710 - Fluid Temperature Sensor 08-42
P0715 - Turbine Speed Sensor Affected
By Interference 08-46
P0730 - Ratio Of Transaxle Error 08-50
P0753 - Shift Solenoid Valve 1 (SSV1)
Open Circuit Or Short To Power Supply
Or Short To Ground 08-56 P0758 - Shift Solenoid Valve 2 (SSV2)
Open Circuit Or Short To Power Supply
Or Short To Ground 08-62
P0763 - Shift Solenoid Valve 3 (SSV3)
Short To Power Supply, P0763 - Shift
Solenoid Valve 3 (SSV3) Open Or
Short To Ground Circuit 08-68
P0768 - Shift Solenoid Valve 4 (SSV4)
Short To Power Supply, P0768 - Shift
Solenoid Valve 4 (SSV4) Open Or
Short To Ground Circuit 08-74
P0773 - Shift Solenoid Valve 5 (SSV5)
Short To Power Supply, P0773 - Shift
Solenoid Valve 5 (SSV5) Open Or
Short To Ground Circuit 08-81
P0775 - EVM (Modulation Solenoid
Valve) Open Circuit Or Short To
Ground, P0775 - EVM (Modulation
Solenoid Valve) Shorted To Voltage 08-87
P0795 - Torque Converter Lock
Solenoid Valve (EVLU) Open Circuit Or
Short To Ground, P0795 - Torque
Converter Lock Solenoid Valve (EVLU)
Short To Voltage 08-93
P0840 - Pressure Sensor 08-99
P1928 - Shift Lock Solenoid Valve
Circuit Shorted To Voltage 08-104
P1928 - Shift Lock Solenoid Valve
Open Circuit Or Short To Ground 08-109
P2709 - Shift Solenoid Valve 6 (SSV6)
Short To Power Supply 08-114
P2709 - Shift Solenoid Valve 6 (SSV6)
Open Circuit Or Short To Ground 08-119
08
08–1Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DP0 Transaxle Control Module (TCM) Connector Pin-Out Table
TCM Pin-Out Table
PINCIRCUIT IDENTIFICATION PINCIRCUIT IDENTIFICATION
1 + EVS 29-
2 Flow Control Solenoid Valve (+) 30-
3 -31Shift 2
4 -32Shift 3
5 -33Shift 4
6 -34P/N Switch
7 Shift Solenoid Valve 3 35-
8 Shift Solenoid Valve 4 36Sequential (-)
9 Shift Solenoid Valve 2 37Sequential (+)
10 Shift Solenoid Valve 1 38CAN-H
11 Shift Lock 39CAN-L
12 Fluid Cooler Flow Control 40Winter Mode
13 Shift Solenoid Valve 5 41-
14 Shift Solenoid Valve 6 42MFS Switch
15 -43Brake Switch
16 Brake Switch 44-
17 -45Turbine Shaft (+)
18 -46Turbine Shaft (-)
19 CDE EVM PTG 47Secondary Shaft (-)
20 Torque Converter Lock Solenoid Valve
(CDE EVM PRSN) 48
Secondary Shaft (+)
21 -49 -
22 -50 -
23 -51 -
24 Regulated Sensor Supply 52-
25 Sensor (GND) 53Fluid Temperature Sensor (-)
26 Pressure Adjust Solenoid Valve (+EVM) 54 Fluid Temperature Sensor (+)
27 Ignition Switch 55Fluid Pressure Sensor
28 GND 56BATT
GENERAL INFORMATION
08–18Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine NOTE :
Using the TCM electrical harness test tool will help prevent electrical connector terminal damage.
Diagnostic Trouble Code (DTC) List
DP0 Automatic Transaxle DTC List
DTCDTC DEFINITION
P0218 Automatic Transaxle Overheating
P0603 Internal Control Module Memory
P0604 RAM
P0605 Checksum Error
P0641 Sensor Feed
P0657 Solenoid Power Supply Circuit Shorted To Voltage
P0657 SSV Feed Circuit Open
P0705 Multi-function Switch: Prohibited Position
P0706 Multi-function Switch: Intermediate Position
P0709 Multi-function Switch: Affected by Interference
P0710 Fluid Temperature Sensor
P0715 No Turbine Speed Sensor Signal
P0715 Turbine Speed Sensor Affected by Interference
P0720 No Vehicle Speed Sensor Signal
P0720 Vehicle Speed Sensor Affected by Interference
P0720 Vehicle Speed Sensor Signal Consistency
P0730 Cylinder Slip
P0740 Lock-up
P0753 EVS1 Circuit Open
P0753 EVS1 Circuit Shorted To Ground
P0753 EVS1 Circuit Shorted To Voltage
P0758 EVS2 Circuit Open
P0758 EVS2 Circuit Shorted To Voltage
P0763 EVS3 Circuit Open
P0763 EVS3 Circuit Shorted To Voltage
P0768 EVS4 Circuit Open
P0768 EVS4 Circuit Shorted To Ground
P0768 EVS4 Circuit Shorted To Voltage
P0773 EVS5 Circuit Open
P0773 EVS5 Circuit Shorted To Voltage
P0775 EVM (Electronic Valve Modulation) Circuit Open
P0775 EVM (Electronic Valve Modulation) Circuit Shorted To Voltage
P0795 EVLU Circuit Open
P0795 EVLU Shorted To Voltage
P0819 Flick Shift Contact Duration
P0819 Flick Shift Contacts
P0840 Pressure Sensor
P0850 P/N Contact
DIAGNOSIS & TESTING
08–20Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine DTCDTC DEFINITION
P1928 Shift Lock Solenoid Valve Circuit Open
P1928 Shift Lock Solenoid Valve Shorted To Voltage
P2709 EVS6 Circuit Open
P2709 EVS6 Circuit Shorted To Voltage
P2753 EPDE Circuit Open
P2753 EPDE Circuit Shorted To Ground
U0001 CAN Communication Error
U0100 Link to EMS
U1100 Coolant Temperature Not Sent By EMS
U111F Engine Speed Not Sent By EMS
U1120 Actual Torque Not Sent By EMS
U1121 Pedal Position Not Sent By EMS
U1122 Expected Torque Not Sent By EMS
U112B Torque Without Reduction Consistency
U112B Torque Without Reduction Not Sent By EMS
DIAGNOSIS & TESTING
08
08–21Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Operating Components Condition
•Related Operating Components
RELATED OPERATING COMPONENT
GEARSHIFT LEVER
POSITION GEAR
RATIO ENGINE
START PARKING
MECHANISM DRIVE
LOCK
2, 3, 4
GEAR
CLUTCH (E2) REVERSE
AND 1-3 GEAR
CLUTCH (E1) 4 GEAR
BRAKE (F1) REVERSE
GEAR
BRAKE (F2) 1, 2
GEAR
BRAKE (F3)
P Parking - Enabled - -- -
R Reverse
Gear -2.45 -
-- - -
N Neutral
Gear - Enabled -
- -- -
D Gear 1 2.75 -
-- -- 
Gear 2 1.5 - ----- 
Gear 3 1.000 - -- -- -
Gear 4 0.71 - --- --
 Operating components
On Board Diagnostic Logic
• Self-diagnosis detection logic.
DTC NO. DTC DEFINITION DTC DETECTION
CONDITION DTC SET
CONDITION POSSIBLE CAUSE
P0730 Ratio of transaxle
error Vehicle is driving The Transaxle
Control Module
(TCM) detects that a
Gear Ratio Error is
already present. The
DTC is set if the
fault happened
within seconds of a
shift. •
Input shaft speed
sensor
• Output shaft speed
sensor
• The retainer of
deceleration clutch
• Transfer case
driven and drive gear
• 2, 3, 4 gear clutch
(E2)
• Reverse and1-3
gear clutch (E1)
• 4 gear brake (F1)
• Reverse gear
brake (F2)
• 1, 2 gear brake
(F3)
• Noise interference
DTC Confirmation Procedure:
Before performing the following procedure, confirm that battery voltage is more than 12 V.
• Connect the X-431 scan tool to the Data Link Connector (DLC) - use the most current software available.
• Turn ignition switch on, with the scan tool, view and erase stored DTCs in the TCM.
• Start the engine and warm it to normal operating temperature.
• With the scan tool, select view DTC and data stream.
• If the DTC is detected, the DTC condition is current. Go to Diagnostic Procedure - Step 1.
• If the DTC is not detected, the DTC condition is intermittent (See Diagnostic Help and Intermittent DTC Trou-
bleshooting in Section 08 Transaxle & Transfer Case for more information).
DIAGNOSIS & TESTING
08
08–51Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3.CHECK SHIFT SOLENOID VALVE 1 (SSV1) RESISTANCE
• Check SSV1 resistance as follows:
SHIFT SOLENOID COMPONENTS
NUMBER SOLENOID
1Shift Solenoid Valve
1
2 Shift Solenoid Valve
2
3 Shift Solenoid Valve
3
4 Shift Solenoid Valve
4
5 Shift Solenoid Valve
5
6 Shift Solenoid Valve
6
7 Pressure Adjust
Solenoid Valve
8 Torque Converter
Lock Solenoid Valve
9 Manual Valve
10 Valve Body
• Check SSV1 resistance as shown in the following table:
SHIFT SOLENOID
VA LV E A/T ASSEMBLY
TERMINAL
VALVE 1 (SSV1) B11-B3
VALVE 2 (SSV2) B8-B3
VALVE 3 (SSV3) B10-B3
VALVE 4 (SSV4) B7-B3
VALVE 5 (SSV5) B5-B3
VALVE 6 (SSV6) B2-B3
RESISTANCE (23°C) 38-42(
)
Is the check result normal?
Ye s>>Replace the valve with a known good one.
With X-431, perform the solenoid actuate test.
If the solenoid can be heard, Go to step 6.
If the solenoid can’t be heard, Go to the next step.
No
>>Replace the damaged solenoid valve.
DIAGNOSIS & TESTING
08
08–59Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3.CHECK SHIFT SOLENOID VALVE 2 (SSV2) RESISTANCE
• Check SSV2 resistance as follows:
NUMBER SOLENOID
1Shift Solenoid Valve 1
2 Shift Solenoid Valve 2
3 Shift Solenoid Valve 3
4 Shift Solenoid Valve 4
5 Shift Solenoid Valve 5
6 Shift Solenoid Valve 6
7 Pressure adjust solenoid
valve
8 Torque converter lock
solenoid valve
9 Manual valve
10 Valve body
• Check SSV2 resistance as shown in the following table:
SHIFT SOLENOID VALVE A/T ASSEMBLY
TERMINAL
VALVE 1 (SSV1) B11-B3
VALVE 2 (SSV2) B8-B3
VALVE 3 (SSV3) B10-B3
VALVE 4 (SSV4) B7-B3
VALVE 5 (SSV5) B5-B3
VALVE 6 (SSV6) B2-B3
RESISTANCE (23°C) 38-42()
Is the check result normal?
Ye s>>Replace the valve with a known good one.
With X-431, perform the solenoid actuate test.
If the solenoid can be heard, go to step 6.
If the solenoid can’t be heard, go to the next step.
No
>>Replace the damaged solenoid valve.
DIAGNOSIS & TESTING
08
08–65Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3.CHECK SHIFT SOLENOID VALVE 3 (SSV3) RESISTANCE
• Check SSV3 resistance as follows:
NUMBER SOLENOID
1Shift Solenoid Valve 1
2 Shift Solenoid Valve 2
3 Shift Solenoid Valve 3
4 Shift Solenoid Valve 4
5 Shift Solenoid Valve 5
6 Shift Solenoid Valve 6
7 Pressure adjust solenoid
valve
8 Torque converter lock
solenoid valve
9 Manual valve
10 Valve body
• Check SSV3 resistance as shown in the following table:
SHIFT SOLENOID VALVE A/T ASSEMBLY
TERMINAL
VALVE 1 (SSV1) B11-B3
VALVE 2 (SSV2) B8-B3
VALVE 3 (SSV3) B10-B3
VALVE 4 (SSV4) B7-B3
VALVE 5 (SSV5) B5-B3
VALVE 6 (SSV6) B2-B3
RESISTANCE (23°C) 38-42()
Is the check result normal?
Ye s>>Replace the valve with a known good one.
With X-431, perform the solenoid actuate test.
If the solenoid can be heard, go to step 6.
If the solenoid can’t be heard, go to the next step.
No
>>Replace the damaged solenoid valve.
DIAGNOSIS & TESTING
08
08–71Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3.CHECK SHIFT SOLENOID VALVE 4 (SSV4) RESISTANCE
• Check SSV4 resistance as follows:
NUMBER SOLENOID
1Shift Solenoid Valve 1
2 Shift Solenoid Valve 2
3 Shift Solenoid Valve 3
4 Shift Solenoid Valve 4
5 Shift Solenoid Valve 5
6 Shift Solenoid Valve 6
7 Pressure adjust solenoid
valve
8 Torque converter lock
solenoid valve
9 Manual valve
10 Valve body
• Check SSV4 resistance as shown in the following table:
SHIFT SOLENOID VALVE A/T ASSEMBLY
TERMINAL
VALVE 1 (SSV1) B11-B3
VALVE 2 (SSV2) B8-B3
VALVE 3 (SSV3) B10-B3
VALVE 4 (SSV4) B7-B3
VALVE 5 (SSV5) B5-B3
VALVE 6 (SSV6) B2-B3
RESISTANCE (23°C) 38-42()
Is the check result normal?
Ye s>>Replace the valve with a known good one.
With X-431, perform the solenoid actuate test.
If the solenoid can be heard, go to step 6.
If the solenoid can’t be heard, go to the next step.
No
>>Replace the damaged solenoid valve.
DIAGNOSIS & TESTING
08
08–77Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine 3.CHECK SHIFT SOLENOID VALVE 5 (SSV5) RESISTANCE
• Check SSV5 resistance as follows:
NUMBER SOLENOID
1Shift Solenoid Valve 1
2 Shift Solenoid Valve 2
3 Shift Solenoid Valve 3
4 Shift Solenoid Valve 4
5 Shift Solenoid Valve 5
6 Shift Solenoid Valve 6
7 Pressure adjust solenoid
valve
8 Torque converter lock
solenoid valve
9 Manual valve
10 Valve body
• Check SSV5 resistance as shown in the following table:
SHIFT SOLENOID VALVE A/T ASSEMBLY
TERMINAL
VALVE 1 (SSV1) B11-B3
VALVE 2 (SSV2) B8-B3
VALVE 3 (SSV3) B10-B3
VALVE 4 (SSV4) B7-B3
VALVE 5 (SSV5) B5-B3
VALVE 6 (SSV6) B2-B3
RESISTANCE (23°C) 38-42()
Is the check result normal?
Ye s>>Replace the valve with a known good one.
With X-431, perform the solenoid actuate test.
If the solenoid can be heard, go to step 6.
If the solenoid can’t be heard, go to the next step.
No
>>Replace the damaged solenoid valve.
DIAGNOSIS & TESTING
08–84Chery Automobile Co., Ltd.