water pump CHERY TIGGO 2009 Service Repair Manual

Downloaded from www.Manualslib.com manuals search engine Torque Specifications
CAUTION:
When torquing a fastener in two steps, DO NOT use a torque wrench for the second step.
DESCRIPTIONTORQUE (N·m)
Alternator Adjusting Bolt 10
Alternator Bracket Bolt 24
Alternator Center Nut 45
Camshaft Position Sensor Bracket 14
Camshaft Position Sensor 10
Camshaft Position Sensor Cylinder 22
Crank Belt Gear 25
Ignition Coil 10
Locking Bolt 22
Spark Piston 25
Water Pump Belt Gear 9
Timing Belt Automatic Tensioner Bolt 24
Belt Gear of Balance Axle 46
Central Belt Wheel Bolt 36
Lower Balance Shaft Bolt 55
Timing Belt Cover Bolts 11
Tensioner Wheel Bolt 49
Tensioner Arm Bolt 22
Tensioner Bracket 49
Timing Belt Indicator 09
Timing Belt Rear Cover 11
Upper Balance Shaft Tensioner Bolt 19
Camshaft Pulley Bolt 90
Crankshaft Pulley Bolt 120
Connecting Bolt of Outflow Pipe 20
EGR Valve 22
Exhaust Manifold Nut (M8) 30
Exhaust Manifold Nut (M10) 50
Fuel Pressure Regulator 9
Fuel Return Pipe 09
Injector and Distribution Pipe 12
Intake Manifold Bolt 20
Intake Manifold Bracket 14
Thermostat Housing Bolt 24
Water Pump Bolts 14
Rocker Cover Bolt 4
Rocker and Camshaft Assembly Bolt 32
Trust Bearing Cover Bolt 19
GENERAL INFORMATION
02–153Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine GENERAL INFORMATION
Description
Water Pump Assembly - 1.6L & 1.8L & 2.0L
1 - Water Pump Assembly
2 - Water Pump Alignment Pin
3 - Water Pump Bolt
4 - Gasket
5 - Engine Inlet Hose From Radiator
6 - Restrictor Outlet Hose7 - Restrictor Inlet Hose
8 - Engine Oil Cooler Inlet Hose (Part 1)
9 - Three Way Connector
10 - Engine Oil Cooler Inlet Hose (Part 2)
11 - Engine Oil Cooler Outlet Hose
LTSM060006
06–2Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine The cooling system regulates engine operating temperature. It allows the engine to reach normal operating temper-
ature as soon as possible, maintains normal operating temperature and prevents overheating.
The cooling system also provides a means of heating the passenger compartment. The cooling system is pressurized
and uses a centrifugal water pump to circulate coolant throughout the system.
The cooling system consists of the following components:
•Radiator
• Coolant
• Coolant pump
• Electric cooling fans
• Electric cooling fans control module
• Thermostat
• Coolant reservoir
Thermostat Housing Assembly - 1.6L & 1.8L & 2.0L
1 - Gasket
2 - Coolant Temperature Sensor
3 - Thermostat Housing Assembly
4 - Thermostat Housing Mounting Bolts5 - Minor Cycle Water Hose
6 - Thermostat Housing Cover
7 - Thermostat Housing Cover Mounting Bolts
8 - Thermostat Assembly
GENERAL INFORMATION
LTSM060007
06
06–3Chery Automobile Co., Ltd.

Downloaded from www.Manualslib.com manuals search engine Thermostat Inspection
1. Inspect the sealing surface of the thermostat (theseat should be tight at room temperature).
2. Inspect the opening temperature and maximum stroke of the thermostat.• Opening temperature of the thermostat is 87°
± 2°C
• Maximum stroke of the thermostat is 8 mm
• Full opening temperature of the thermostat is
104°C
3. Verify the thermostat closes 5°C lower than the opening temperature.
4. If the thermostat fails any of the inspection steps, replace the thermostat.
Coolant Pump
Removal & Installation - 1.6L & 1.8L & 2.0L
WARNING!
Always allow the engine to cool before opening the cooling system. Do not remove the coolant pressure relief
cap when the engine is operating or the cooling system is hot. The cooling system is under pressure; steam and
hot liquid can come out forcefully when the cap is loosened slightly. Failure to follow these instructions may
result in serious personal injury.
1. Drain the cooling system (See Cooling System Draining Procedure in Section 06 Cooling System).
2. Remove the timing belt (See Timing Belt Removal & Installation in Section 02 Engine).
3. Remove the coolant pump mounting bolts (1).(Tighten: Coolant pump mounting bolts to 15 N·m)
4. Remove the water pump and gasket.
5. Installation is in the reverse order of removal.
Installation Notes:
• Install a new coolant pump gasket during installa-
tion (1).
• Verify the cooling system is filled to proper
specifications.
ON-VEHICLE SERVICE
LTSM060014
BESM060001
BESM060002
06–16Chery Automobile Co., Ltd.