oil type CHEVROLET CAMARO 1967 1.G Chassis Owner's Guide

ENGINE COOLING 6K-2

are indicative of exhaust gases leaking into the coolr

ing system.

Periodic Maintenance

Periodic service must be performed to the engine cool-

ing system to keep it in efficient operating condition.

These services should include a complete cleaning and

reverse flushing as well as a reconditioning service.

In the course of engine operation, rust and scale ac-

cumulate in the radiator and engine water jacket. The

accumulation of these deposits can be kept to a minimum

by the use of a good rust inhibitor but it should be

remembered that an inhibitor will not remove rust al-

ready present in the cooling system.

Two common causes of corrosion are: (1) air suction--

Air may be drawn into the system due to low liquid level

in the radiator, leaky water pump or loose hose con-

nections; (2) exhaust gas leakage—Exhaust gas may be

blown into the cooling system past the cylinder head

gasket or through cracks in the cylinder head and block.

Cleaning

A good cleaning solution should be used to loosen the

rust and scale before reverse flushing the cooling

system. There are a number of cleaning solutions avail-

able and the manufacturer's instructions with the particu-

lar cleaner being used should always be followed.

An excellent preparation to use for this purpose is GM

Cooling System Cleaner. The following directions for

cleaning the system applies only when this type cleaner

is-used.

1.
Drain the cooling system including the cylinder block

and then close both drain plugs.

2.
Remove thermostat and replace thermostat housing.

3.
Add the liquid portion (No. 1) of the cooling system

cleaner.

4.
Fill the cooling system with water to a level of about

3 inches below the top of the overflow pipe.

5. Cover the radiator and run the engine at moderate

speed until engine coolant temperature reaches 180

degrees.

6. Remove cover from radiator and continue to run the

engine for 20 minutes. Avoid boiling.

7. While the engine is still running, add the powder

portion (No. 2) of the cooling system cleaner and

continue to run the engine for 10 minutes.

8. At the end of this time, stop the engine, wait a few

minutes and then open the drain cocks or remove

pipe plugs. Also remove lower hose connection.

CAUTION: Be careful not to scald your hands.

NOTE:
Dirt and bugs may be cleaned out of

the radiator air passages by blowing out with air

pressure from the back of the core.

Reverse Flushing

Reverse flushing should always be accomplished after

the system is thoroughly cleaned as outlined above.

Flushing is. accomplished through the system in a direc-

tion opposite to the normal flow. This action causes the

water to get behind the corrosion deposits and force

them out.

Radiator

1.
Remove the upper and lower radiator hoses and re-

place the radiator cap,

2.
Attach a lead-away hose at the top of the radiator.
3.
Attach a new piece of hose to the radiator outlet

connection and insert the flushing gun in this hose.

4.
Connect the water hose of the flushing gun to a water

outlet and the air hose to an air line.

5. Turn on the water and when the radiator is full, turn

on the air in short blasts, allowing the radiator to

fill between blasts of air.

CAUTION: Apply air gradually as a clogged

radiator will stand only a limited pressure.

6. Continue this flushing until the water from the lead-

away hose runs clear.

Cylinder Block and Cylinder Head

1.
With the thermostat removed, attach a lead-away

hose to the water pump inlet and a length of new hose

to the water outlet connection at the top of the engine.

NOTE:
Disconnect the heater hose when re-

verse flushing engine.

2.
Insert the flushing gun in the new hose.

3.
Turn on the water and when the engine water jacket

is full, turn on the air in short blasts.

4.
Continue this flushing until the water from the lead-

away hose runs clear.

Hot Water Heater

1.
Remove water outlet hose from heater core pipe.

2.
Remove inlet hose from engine connection.

3.
Insert flushing gun and flush heater core. Care must

be taken when applying air pressure to prevent

damage to the core.

Fan Belt

Adjustment

1.
Loosen bolts at Delcotron slotted bracket.

2.
Pull Delcotron away from engine until desired ten-

sion reading is obtained with a strand tension gauge.

Refer to Section 6, "Engine Tune-Up".

3.
Tighten all Delcotron bolts securely.

Thermostat

The thermostat consists of a restriction valve actuated

by a thermostatic element. This is mounted in the hous-

ing at the cylinder head water outlet above the water

pump,
thermostats are designed to open and close at

predetermined temperatures and if not operating properly

should be removed and tested as follows.

Replacement

1.
Remove radiator to water outlet hose.

2.
Remove thermostat housing bolts and remove water

outlet and gasket from thermostat housing (fig. 2).

3.
Inspect thermostat valve to make sure it is in good

condition.

4.
Place thermostat in hot water 25° above the temper-

ature stamped on the thermostat valve.

5. Submerge the valve completely and agitate the water

thoroughly. Under this condition the valve should

open fully.

6. Remove the thermostat and place in water 10° below

temperature indicated on the valve.

7. With valve completely submerged and water agitated

thoroughly, the valve should close completely.

8. If thermostat checks satisfactorily, re-install, using

a new housing gasket.

9. Refill cooling system.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE FUEL 6M-7

5. On vehicles equipped with automatic transmission

hold throttle rod in full throttle position, pull TV

rod to full detent position and adjust TV rod to just

enter hole on throttle lever, then connect TV rod at

throttle lever.
NOTE:
If equipped with anti-stall device (dash-

pot),
set carburetor fast idle cam on high step

and adjust dash-pot to just contact throttle

lever.

327
CU.
IN.
427
CU.
IN.

Fig.
8C—Throttle Linkage-Corvette

AIR
CLEANERS

INDEX

Page

General Description 6M-7

Service Procedures . . 6M-8

Polyurethane. Element 6M-8

Maintenance 6M-8

Oil Bath 6M-8
Page

Maintenance
...........* 6M-8

Oil
Wetted
Paper
Element
6M-9

Replacement
* . 6M-9

Testing 6M-9

Tool J-7852 . 6M-9

GENERAL DESCRIPTION

Air cleaners on all models operate primarily to re-

move dust and dirt from the air that is taken into the

carburetor and engine. All air cleaners on engines

equipped with "Closed Positive" ventilation incorporate

flame arresters. Every 12,000 miles the flame ar-

resters should be removed, cleaned in solvent and blown

dry with compressed air.

An oil wetted polyurethane element air cleaner (fig. 1A)

is standard equipment on In Line engines. This type

cleaner element is reusable and should be removed,

cleaned, re-oiled and reinstalled every 12,000 miles or

more often during dusty or other adverse driving con-

ditions. The optional, oil bath air cleaner (available on
Chevrolets with L6 engine) should be cleaned and re-

filled with oil at oil change intervals.

On the V8 engines,, a replaceable, oil wetted paper

element type is used (fig; 2A). Both ends of me paper

element are bonded with plastisol sealing material.

The improved oil wetted paper elements have increased

filtering capacity over their dry paper predecessors.

Oil on the paper causes the element to become diBcolored

by a small amount of dirt but does not necessarily mean

the element is plugged or reduced in efficiency. Every

12,000 miles or more often during dusty or other adverse

driving conditions, either replace oil wetted paper ele-

ment or test element using ToolJ-7825.

CHEVROLET CHASSIS SOVICE/MANUAL

ENGINE FUEL
6M-10

the
two
"FILL71 lines
(fig.
6A). Refill whenever
the
level

falls below the lower
<'FILL"
line.

Storing Tool

When
the
tool
is
not used, fully depress
the
inner tube.

This seals
off
the
oil
reservoir from the vent hole
to pre-

vent
oil
loss
if
the tool
is
tipped.

Fig. 6A-Filling Tool with
Oil

FUEL PUMP

INDEX

Page

General Description
. . . . 6M-10

Service Procedures .6M-10

Inspection .6M-10
Page

Test
. . ; 6M-10

Removal
6M-11

Installation
6M-11

GENERAL DESCRIPTION

The fuel pump
(fig. IP)
used
on all
Chevrolet vehicles

covered
in
this manual
are of the
diaphragm type.
The

pumps
are
actuated
by an
eccentric located on
the
engine

camshaft.
On
in-line engines,
the
eccentric actuates
the

rocker arm*
On V-8
engines,
a
push
rod
(located be-

tween
the
camshaft eccentric and fuel pump) actuates
the

pump rocker
arm.
Because
of
design, this pump
is

serviced
as an
assembly only.

Fig.
IP—Fuel Pump (Non-Serviceable)

SERVICE PROCEDURES

Inspection

The fuel pump should
be
checked
to
make sure
the

mounting bolts
and
inlet and outlet connections
are
tight.

Test

Always test pump while
it is
mounted on the engine
and
be sure there
is
gasoline
in
the tank.

The line from
the
tank
to the
pump
is the
suction side

of
the
system and the line from the pump
to the
carbure-

tor
is the
pressure side
of the
system.
A
leak on
the

pressure side, therefore, would
be
made apparent
by

CHEVROLET CHASSIS SERVICE MANUAL

AIR INJECTOR REACTOR SYSTEM
6T-3

MIXTURE

CONTROL

VALVE

SIGNAL

PUMP PRESSURE

(MIXTURE VALVE INLET)

PUMP PRESSURE

(AIR MANIFOLD INLET)

IN LINE
AIR INJECTION

PUMP INLET

MIXTURE

CONTROL

VALVE

SIGNAL

MIXTURE

CONTROL

VALVE

OUTLET

MIXTURE

CONTROL

VALVE

INLET
AIR INJECTION

PUMP INLET

V8 (TYPICAL)
PUMP PRESSURE

(AIR MANIFOLD INLET)

MIXTURE CONTROL

VALVE INLET

MIXTURE CONTROL

VALVE SIGNAL

AIR INJECTION

PUMP INLET

PUMP PRESSURE^

(AIR MANIFOLD

J

MIXTURE CONTROL

VALVE OUTLET
V8 (396-427)

Fig.
4—Air Manifold Hose and Tube Routing (Typical)
a straight pipe thread.
Do
not use
a 1/4"
tapered

pipe
tap. The
hoses
of
the
Air
Injection Reactor

System
are a
special material
to
withstand high

temperature.
No
other type hose should
be

substituted.

• Install
new
hose(s) and/or tube(s), routing them
as

when removed.

• Tighten
all
connections.

NOTE:
Use
anti seize compound
on
threads
of

the
air
manifold
to
exhaust manifold
or
cylinder

head connections.

NOTE:
On
Chevy
n
vehicles equipped with
a

V8 engine,
the air
injection tubes
are
part
of the

air manifold
and
care must
be
used
in
removing

them from
the
exhaust manifold.
It may be

necessary
to
remove
the
exhaust manifold
and

use penetrating
oil on the
injection tubes before

the
air
manifold can
be
removed.

Check Valve

Inspection

•
The
check valve should
be
inspected whenever
the

hose
is
disconnected from
the
check valve
or
when-

ever check valve failure
is
suspected. (A pump that

,
had
become inoperative and had shown indications
of

having exhaust gases
in the
pump would indicate

check valve failure)..

• Orally blow through
the
check valve (toward
air

manifold) then attempt
to
suck back through check

valve. Flow should only
be in one
direction (toward

the
air
manifold).

Replacement

• Disconnect pump outlet hose
at
check valve. Remove

check valve from
air
manifold, being careful not
to

bend
or
twist
air
manifold.

Mixture Control Valve

Inspection

• Check condition
and
routing
of all
lines especially

the signal line.
A
defective signal
or
outlet line will

cause malfunctioning
of the
mixture control valve.

• Disconnect pump
to
valve inlet hose
at
pump.

• Leaking valve will
be
indicated
by an air
gushing

noise coming from
the
hose. Place palm
of
hand over

hose; little
or no
pull with
a
gradual increase
is

normal.
If
immediate strong pull
is
felt
or air
noise

is heard, valve
is
defective
and
should
be
replaced.

• Open
and
close throttle rapidly.
Air
noise should
be

evident
and
then gradually decrease. Check
for

proper valve usage.
If
strong pull
is not
felt
im-.

mediately
or air
noise
is not
present, valve
is not

functioning properly and should be replaced.

•
A
noisy valve should be replaced.

Replacement

• Disconnect
the
signal line,
air
inlet
and air
outlet

hoses then remove
the
valve.

• Install
new
valve
and
connect
air
outlet,
air
inlet

and signal line hoses.

CAUTION: Mixture control valves, though

similar
in
appearance
are
designed
to
meet

particular requirements
of
various engines,

therefore,
be
sure
to
install
the
correct valve.

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-7

CHARGING SYSTEM

INDEX

Page

General Description . 6Y-7

Maintenance and Adjustments 6Y-9

Static Checks . 6Y-10

System Condition Check and Voltage

•Regular Adjustment. 6Y-10

General Output 6Y-11

Generator Diode and Field Test 6Y-12

Indicator Lamp-Initial Field Excitation

Circuit Tests . 6Y-12
Page

Field Circuit Resistance Wire Tests 6Y-13

Field Relay Test and Adjustment 6Y-14

Other Harness Checks 6Y-14

Service Operations 6Y-14

Generator 6Y-14

Removal and Installation 6Y-14

Pulley Replacement. 6Y-14

Brush Replacement (6" Delcotron). 6Y-15

Double Contact Regulator . . . . . . 6Y-16

GENERAL DESCRIPTION

The charging system includes the battery, generator,

regulator, telltale light, and necessary wiring to connect

these components. The Delcotron is offered as standard

equipment, although there are various capacities avail-

able on all models.

The Delcotron continuous output A.C. generator (fig.

lc) consists of two major parts, a stator and a rotor. The

stator is composed of a large number of windings as-

sembled on the inside of a laminated core that is attached

to the generator frame. The rotor revolves within the

stator on bearings located in each end frame. Two

brushes are required to carry current through the two

slip rings to the field coils wound concentric with the

shaft of the rotor. Six rectifier diodes are mounted in the

slip ring end frame and are joined to the stator windings

at three internally located terminals.

Diodes are mounted in heat sinks to provide adequate

heat dissipation. The six diodes replace the separately
mounted rectifier as used in other types of application.

The diodes change the Delcotron A.C. current to D.C.

current.

Two regulators (fig. 2c) are available on the 1967 vehi-

cles,
a double contact two unit type and a transistor

regulator. The function of these regulators in the charg-

ing system is to limit the generator voltage to a pre-set

value by controlling the generator field current. Both

regulators have an internal field relay unit. The relay

unit allows the telltale lamp to light (as a bulb check)

with the ignition key on and engine not running. When the

engine is started and the generator begins to charge, the

indicator light goes out indicating that the system is op-

erating normally.

The double contact regulator, when used with the

special 63 amp air conditioning model generator (4 ohm

field coil) uses a field discharge diode internally in the

field circuit (figs. 3c and 4c). The added diode adapts the

BRUSH AND

TERMINAL

ASSEMBLY

SLIP RINGS
SLIP RING

END FRAME

_\

THRU

BOLT
DRIVE END

FRAME

BEARING

BEARING

DIODES

ROTOR

5.5" SERIES ID DELCOTRON
STATOR

ASSEMBLY
GREASE

RESERVOIR

BRUSH

FAN ASSEMBLY

6.2" SERIES 2D TYPE 150 DELCOTRON

Fig.
lc—Delcotron Cross-section View

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-8

1

FIELD RELAY^I^p2

"LATCH"
^PFN?^

"P1
TERMINAL
JyJvJCTl^

NO. 2 TERMINAD^5^^^«

NO.
3 TERMINAL ^S5«£

NO.
4 TERMINAL ^^^
m

# / VOLTAGE

¥ REGULATOR

1
ACCESS PLUG TO

VOLTAGE ADJUSTMENT

No 4 TERMINAL

Double Contact

Fig.
2c—Voltage Regulator Assemblies
Transistor

regulator to handle the higher field current and enables it

to absorb the increased inductive voltages of the field

coil with satisfactory contact point life.

The double-contact regulator assembly (fig. 2c) con-

sists of a double contact voltage regulator unit and a field

relay unit. This unit uses two sets of contact points on

the voltage regulator unit to obtain desired field excita-

tion under variable conditions. Internal circuit wiring

diagrams of the double contact regulator are shown in

Figures 3c and 4c.

The transistor regulator (fig. 2c) is an assembly com-

posed principally of transistors, diodes, resistors, a

capacitor, and a thermistor to form a completely static

voltage regulating unit in combination with a conventional

vibrating type field relay.

The transistor is an electrical device which limits the
generator voltage to a preset value by controlling the

generator field current. The diodes, capacitor and re-

sistors act together to aid the transistors in controlling

the generator voltage. This is the only function that the

regulator performs in the charging circuit. The

thermistor provides a temperature-compensated voltage

setting. Wiring diagrams of the transistor regulator are

shown in Figures 3c and 4c.

The voltage at which the generator operates is deter-

mined by the regulator adjustment. The regulator voltage

setting can be adjusted externally by removing a pipe plug

in the cover (fig. 2c) and turning the adjusting arm inside

the regulator. This procedure is explained in the followr

ing section, and permits regulator adjustments without

removing the cover.

FUSIBLE

DOUBLE CONTACT
FUSIBLE LINK-^
JUNCTION HORN

BLOCK RELAY

RESISTOR

Q FIELD Q>

DELCOTRON TR-

TRANSISTOR
FUSIBLE LINK-

Fig.
3c-Circuity - Voltage Regulator Assemblies (Except Corvette)

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-18

IGNITION SYSTEMS

INDEX

Page

General Description . 6Y-18

Maintenance and Adjustments 6Y-19

Breaker Point System 6Y-19

Breakerless System . . 6Y-X9

Ignition Coil Check 6Y-19

Spark Plugs 6Y-19

Service Operations , 6Y-19

Distributor Contact Points . 6Y-19

Cleaning 6Y-19

Replacement 6Y-20

Setting Dwell Angle 6Y-21

Distributor Condenser 6Y-22

Performance Diagnosis. 6Y-22

Replacement . . 6Y-23

Distributor

Breaker Point Type 6Y-23

Removal. . 6Y-23

Disassembly • 6Y-23
Page

Cleaning and Inspection .....'.., 6Y-25

Assembly . 6Y-25

Installation 6Y-26

Breakerless i 6Y-27

Removal . 6Y-27

Disassembly and Assembly 6Y-27

Installation 6Y-27

Off-Engine Test. . 6Y-27

Coil Replacement 6Y-27

Pulse Amplifier. 6Y-28

Disassembly .6Y-4S8

Component Checks
!
6Y-28

Assembly 6Y-29

Ignition Switch Replacement 6Y-29

Spark Plugs 6Y-30

Cleaning and Regapping I ....... 6Y-30

Installation . 6Y-31

GENERAL DESCRIPTION

There are two ignition systems available on 1967

vehicles. The breaker point type which is continued as

the regular production system and the optional (Corvette

only) transistor controlled breakerless ignition system

(magnetic pulse type). The transistor ignition system

features a specially designed distributor, control unit

(ignition pulse amplifier), and a special coil. Two resist-

ance wires are also used in the circuit; one as a ballast

between the coil negative terminal and ground, while the

other resistance wire provides a voltage drop for the

engine run circuit and is by-passed at cranking. The

other units in the system (the ignition switch, spark

plugs,
and battery) are of standard design. The dis-

tributor and control unit (ignition pulse amplifier) are

shown in Figures li and 2i.

CAP-

VACUUM

PICK-UP

COIL LEADS

PICK-UP COIL

CONNECTOR BODY
Although the external appearance of the distributor

resembles a standard distributor, the internal construc-

tion is quite different. As shown in the exploded view

(fig. 16i) an iron timer core replaces the conventional

breaker cam. The timer core has the same number of

equally-spaced projections, or vanes as engine cylinders.

The timer core rotates inside a magnetic pickup as-

sembly, which replaces the conventional breaker plate,

contact point set, and condenser assembly. The magnetic

pickup assembly consists of a ceramic permanent mag-

net, a pole piece, and a pickup coil. The pole piece
is.
a

steel plate having equally spaced internal teeth, one tooth

for each cylinder of the engine.

The magnetic pickup assembly is mounted over the

main bearing of the distributor housing, and is made to

rotate by the vacuum control unit, thus providing vacuum

advance. The timer core is made to rotate about the shaft

by conventional advance weights, thus providing centrifu-

gal advance.

Fig.
li—
Magnetic Pulse Distributor
Fig.
2i-lgnition Pulse Amplifier Unit

CHEVROLET CHASSIS SERVICE MANUAL

MAINTENANCE AND ADJUSTMENTS
ENGINE-ELECTRICAL 6Y-19

PERIODIC MAINTENANCE

BREAKER POINT SYSTEM

The distributor breaker points and spark plugs are the

only ignition system components that require periodic

service. The remainder of the ignition system requires

only periodic inspection to check operation of the units,

tightness of the electrical connections, and condition of

the wiring. When checking the coil, test with a reputable

tester.

Breaker type distributors are equipped with cam lubri-

cator and should have the wick replaced at the same time

contact point set is replaced. It is not necessary to

lubricate the breaker cam when using a cam lubricator.

Do not attempt to lubricate the wick - Replace when

necessary. When installing a new wick, adjust its posi-

tion so the end of the wick just touches the lobe of the

breaker cam.

Distributor shaft lubrication is accomplished by a

reservoir of lube around the mainshaft in the distributor

body.

BREAKERLESS SYSTEM

Since there are no moving parts in the ignition pulse

amplifier unit mounted forward of the radiator bulkhead,

and the distributor shaft and bushings have permanent

type lubrication, no periodic maintenance is therefore

required for the breakerless ignition system. The dis-

tributor lower bushing is lubricated by engine oil through

a splash hole in the distributor housing, and a housing

cavity next to the upper bushing contains a supply of

lubricant which will last between overhaul periods. At

time of overhaul, the upper bushing may be lubricated

by removing the plastic seal and then adding SAE 20 oil

to the packing in the cavity. A new plastic seal will be

required since the old one will be damaged during

removal.

Tachometer readings for test purposes can be made on

the primary circuit of the breakerless ignition system in

the same manner as on the conventional ignition system,

however before attempting to connect a test tachometer

into the primary circuit check with your instrument

supplier to insure that satisfactory readings can be

obtained and the breakerless system will not be damaged

by the tachometer that is to be used,

IGNITION COIL CHECK (BREAKERLESS)

The ignition coil primary can be checked for an open
PULSE

AMPLIFIER

IGN. SWITCH WIRE

"("IGN" TERMINAL)
-E3 IJU
12
WHITE-

-20 BLACKf' • 12 WHITE-

Fig.
3i—
Breakerless Ignition System

condition by connecting an ohmmeter across the two

primary terminals with the battery disconnected. Pri-

mary resistance at 75
°F.
should be between .35 and .55

ohm. An infinite reading indicates the primary is open.

For the engine to run but miss at times, the primary

open may be of the intermittent type.

The coil secondary can be checked for an open by con-

necting an ohmmeter from the high tension center tower

to either primary terminal. To obtain a reliable reading,

a scale on the ohmmeter having the 20,000 ohm value

within, or nearly within, the middle third of the scale

should be used. Secondary resistance at 75°F. should be

between
8,000
and 12,500 ohms. If the reading is infinite,

the coil secondary winding is open.

A number of different types of coil testers are avail-

able from various test equipment manufacturers. When

using these testers, follow the procedure recommended

by the tester manufacturer.

tester will properly
NOTE:
Make sure the

check this special coil.

SPARK PLUGS

Should be removed, inspected cleaned and regapped at

tune-up. Defective plugs should be replaced, see Servic-

ing of Units Off the Vehicle.

SERVICE OPERATIONS

DISTRIBUTOR CONTACT POINTS

CLEANING

Dirty contact points should be dressed with a few

strokes of a clean, fine-cut contact file. The file should

not be used for other metals and should not be allowed to

become greasy or dirty. Never use emery cloth to clean

contact points. Contact surfaces, after considerable use,

may not appear bright and smooth, but this is not neces-
sarily an indication that they are not functioning satis-

factorily. Do not attempt to remove all roughness nor

dress the point surfaces down smooth; merely remove

scale or dirt.

Badly burned or pitted contact points should be re-

placed and the cause of trouble determined so it can be

eliminated. High resistance or loose connections in the

condenser circuit, oil or foreign materials on the contact

surfaces, improper point adjustment or high voltages may

CHEVROLET CHASSIS SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-23

condenser leak or to a defective connection. This

will cause burned points and ignition failure upon

initial starts and at high speeds.

4.
Capacity - Capacity is determined by the area of

the metallic elements and the insulating and im-

pregnating materials.

For a complete check of the condenser, use a tester

which will check for all of the above conditions. Follow

the instructions given by the manufacturer of the

test equipment. Condenser capacity should be
.18-:
23

microfarads.

REPLACEMENT

Four and Six Cylinder Engine Distributor (Fig. 4i)

1.
Release distributor cap hold-down screws, remove

cap and place it out of the work area.

2.
Remove rotor.

3.
Disconnect condenser lead wire from contact point

quick-disconnect terminal.

4.
Remove condenser attaching screw, lift.condenser

from breaker plate and wipe breaker plate clean.

5. Install new condenser using reverse of procedure

outlined above.

Eight Cylinder Engine Distributor

1.
Remove distributor cap.

2.
Loosen condenser lead attaching screw (fig. 6i) and

lift out condenser lead clip.

3.
Remove screw holding condenser bracket to breaker

plate and slide condenser from bracket.

4.
To replace condenser reverse the above procedure.

NOTE:
Make sure that new condenser lead is

installed in proper position (fig. 6i).

DISTRIBUTOR

(BREAKER POINT TYPE)

REMOVAL

1.
On radio equipped Corvettes, remove ignition shield

from over distributor and coil. One bolt is accessible

from top of shield, the other two are at rear of

shield, facing firewall.

2.
Release the distributor cap hold-down screws, re-

move the cap and place it clear of the work area.

NOTE:
If necessary, remove secondary leads

from the distributor cap after first marking the

cap tower for the lead to No. 1 cylinder. This

will aid in the reinstallation of leads in the cap.

3.
Disconnect the distributor primary lead from the coil

terminal.

4.
Scribe a realignment mark on the distributor bowl

and engine in line with the rotor segment.

5. Disconnect vacuum line to distributor and tachometer

drive cable (Corvette). Remove the distributor hold-

down bolt and elamp and remove the distributor from

the engine. Note position of vacuum advance mecha-

nism relative to the engine.

CAUTION: Avoid rotating the engine with the

distributor removed as the ignition timing will

be upset.
Rg.
121-L-6 Distributor-Exploded View

1.
Breaker Plate Attaching

Screws

2.
Condenser Attaching

Screws

3. Condenser

4.
Breaker Plate Assembly

4a.
Cam Lubricator

5. Vacuum Control Assembly

6. Vacuum Control

Attaching Screws

7. Housing

8. Cap

9. Rotor

DISASSEMBLY
10.
Contact Point

Attaching Screw

11.
Contact Point Assembly

12.
Weight Cover

Attaching Screws

13.
Weight Cover

14.
Weight Springs

15.
Advance Weights

16. Cam Assembly

17.
Main Shaft Assembly

18.
Roll Pin

19.
Drive Gear

It is advisable to place the distributor in a distributor

testing machine or synchroscope prior to disassembly.

CHEVROLET CU
SERVICE MANUAL

ENGINE-ELECTRICAL 6Y-27

timing mark on pulley lines up with timing tab.

2.
Position distributor to opening in block in normal

installed attitude (fig. 15i), noting position of vacuum

control unit.

3.
Position rotor to point toward front of engine (with

distributor housing held in installed attitude), then

turn rotor counter-clockwise approximately 1/8 turn

more toward left cylinder bank and push distributor

down to engine camshaft. It may be necessary to ro-

tate rotor slightly until camshaft engagement is felt.

4.
While pressing firmly down on distributor housing,

kick starter over a few times to make sure oil pump

shaft is engaged. Install hold-down clamp and bolt

and snug up bolt.

5. Turn distributor body slightly until points just open

and tighten distributor clamp bolt.

6. Place distributor cap in position and check to see

that rotor lines up with terminal for No. 1 spark

plug.

7. Install cap, check all high tension wire connections

and connect spark plug wires if they have been re-

moved. It is important that the wires be installed in

their location in the supports.

NOTE:
The brackets are numbered to show the

correct installation. Wires must be installed as

indicated to prevent cross firing.

8. Connect vacuum line to distributor and distributor

primary wire to coil terminal.

9. Start engine and set timing as described under Turn-

Up in Section 6.

BREAKERLESS (MAGNETIC PULSE)

DISTRIBUTOR

REMOVAL (CORVETTE)

1.
If vehicle is equipped with radio, remove three bolts

securing ignition shield over distributor and coil.

One bolt is accessible from the top of shield, the

other two are at rear of shield, facing firewall.

2.
Disconnect tachometer drive cables from distributor

housing.

3.
Disconnect pickup coil leads at connector.

4.
Remove distributor cap.

5. Crank engine so rotor is in position to fire No. 1

cylinder and timing mark on harmonic balancer is

indexed with pointer.

6. Remove vacuum line from distributor.

7. Remove distributor clamping screw and hold-down

clamp.

8. Remove distributor and distributor-to-block gasket.

It will be noted that the rotor will rotate as the

distributor is pulled out of the block. Mark the re-

lationship of the rotor and the distributor housing

after removal so that the rotor can be set in the

same position when the distributor is being installed.

DISASSEMBLY (Fig. 16i)

NOTE:
If a distributor is being disassembled

for replacement of the stationary magnetic

pickup assembly only, it will be necessary to

perform only Steps 3, 4, 5, 7, 8, 9, and 12 of the

service procedure listed below.
1.
Remove screws securing rotor and remove rotor.

2.
Remove centrifugal weight springs and weights.

3.
Remove the tachometer drive gear from the distribu-

tor (Corvette only).

4.
Remove roll pin, then remove distributor drive gear

and washer.

CAUTION: To prevent

magnet, support drive gear
;e to the permanent

?n
driving out roll

pin.

5. Remove drive shaft assembly.

6. Remove centrifugal weight support and timer core

from drive shaft.

7. Remove connector from pickup coil leads.

8. Remove retaining ring which secures magnetic

core support plate to distributor shaft bushing in

housing.

9. As a unit, remove the entire magnetic pickup assem-

bly from the distributor housing.

10.
Remove brass washer and felt pad.

11.
Remove vacuum advance unit.

12.
To reassemble distributor, perform the above steps

in reverse order.

INSTALLATION (CORVETTE)

1.
Check to see that the engine is at firing position for

No.
1 cylinder (timing mark on harmonic balancer

indexed with pointer).

2.
Position a new distributor-to-block gasket on the

block.

3.
Before installing distributor, index rotor with hous-

ing as noted when distributor was removed. Install

distributor in block so that vacuum diaphragm faces

approximately 45° forward on the right side of the

engine and the rotor points toward contact in cap for

No.
1 cylinder.

4.
Replace distributor clamp leaving screw loose

enough to allow distributor to be turned for timing

adjustment.

5. Install spark plug wires in distributor cap. Place

wire for No. 1 cylinder in tower (marked on old cap

during disassembly) then install remaining wires

clockwise around the cap according to the firing

order (1-8-4-3-6-5-7-2).

6. Attach distributor to coil primary wires.

7. Replace distributor cap.

8. Adjust timing and then fully tighten distributor clamp

screw.

9. Attach vacuum line to distributor.

10.
Connect tachometer drive cables to distributor body.

11.
Replace ignition shields.

DISTRIBUTOR OFF-ENGINE TEST

The distributor's centrifugal and vacuum advance can

be checked in a distributor testing machine or synchro-

scope specially adapted or designed to accommodate this

type distributor. However, since this involves removing

the distributor from the engine, this test may be post-

poned until other system checks have been made. A dwell

reading cannot be obtained on this distributor and it is not

likely that the centrifugal or vacuum advance will be a

cause of trouble.

COIL REPLACEMENT

1.
Disconnect ignition switch and distributor leads from

CHEVROLET CHASSIS SERVICE MANUAL