lock CHEVROLET CORVETTE 1995 4.G Repair Manual

Downloaded from www.Manualslib.com manuals search engine Replace the wheel nuts with the rounded end of the nuts
toward the wheel. Tighten each nut by hand until the
wheel
is held against the hub.
Lower the vehicle by turning the wheel wrench
counterclockwise. Lower the jack completely.
5-35

Downloaded from www.Manualslib.com manuals search engine Tighten the wheel nuts firmly in a criss-cross
sequence as shown. The
LOWELAT TIRE or SERVICE LTPWS light will
stay on as long as you are using the compact spare tire.
It should go out when the original tire is replaced.
After you have the flat tire repaired or replaced, install
the plastic nut caps and tighten them to
22 pound-inches
(2.5 Nem).
Put the jack, wheel nut socket and wheel lock key in the
rear storage compartment behind
the passenger’s seat.
Make sure the parts are stored properly in the foam
container. Position the jack in the container
so that you
can read the yellow CAUTION label from the driver’s
seat. Replace the plastic tray and close the storage
compartment.
5-36

Downloaded from www.Manualslib.com manuals search engine NOTICE:
Your Corvette’s radio receiver box is in the rear
storage compartment.
To help avoid damage,
carefully place the jack, socket and wheel lock
key into the foam container in the compartment.
Do not toss or place the items against the radio
receiver box or any wiring.
Storing a Flat Tire (Except ZR-1 Rear Tires)
If you have not chosen the spare tire delete option,
you’ll notice the road tire is larger than the spare,
so you
must adjust the tray to its lower position. Lift and
push
the tire carrier tray toward the front of the vehicle. The
tray will drop to its lower position.
5-37

Downloaded from www.Manualslib.com manuals search engine F
Put the flat road tire on the tray. Lift the latch bolt, push
it toward the front
of the vehicle, and the bolt will drop
down to the lower position. Put
the hooked end of the wheel wrench into the slot in
the tray. Lift the tray using the wheel wrench and insert
the latch bolt into the notch in the tray.
To raise the tray,
use the socket end
of the wheel wrench to turn the latch
bolt counterclockwise. Turn the latch bolt until it is snug.
5-38

Downloaded from www.Manualslib.com manuals search engine Filling Your Tank While refueling, place the
cap in the indent to the left
of the filler neck.
To take off the cap, turn it slowly to the left
(counterclockwise).
The cap is under a hinged door on the rear decklid of
your vehicle.

Downloaded from www.Manualslib.com manuals search engine Fog Lamp
You can reach the fog lamps from under the front
bumper.
1. Remove the screw in the access door. Open the door.
2. Turn the bulb base counterclockwise 118 turn and
pull it out.
3. Disconnect the bulb base from the wiring harness.
4. Reverse the steps with a new bulb.
6. Remove the four screws from the retainer near each
comer of the headlamp. Don’t move the large-head
adjusting screws
or your headlamp will not be aimed
properly.
Hold the headlamp and remove the retainer.
7. Remove the headlamp and unplug the electrical
8. Reverse the steps with a new headlamp.
connector.

Downloaded from www.Manualslib.com manuals search engine Front Turn Signal
1. Open the hood.
2. Find the socket at the front of the engine
compartment.
3. Turn the socket counterclockwise 1/4 turn and pull it
out.
4. Push the bulb in, turn it counterclockwise, then pull
5. Reverse the steps with a new bulb. The socket has
it out.
three large tabs and one small tab. Be sure to line
up
the small tab with the small notch in the housing.
6-39

Downloaded from www.Manualslib.com manuals search engine Rear Turn Signal and Taillamp
I
I
1. Remove the screws.
2.
3.
4.
Pull the lens out.
Push the bulb in, turn it counterclockwise, then pull
it out.
Reverse the steps with a new bulb.
To prevent water
from getting inside the lens, make sure the lens seal
is properly positioned.
6-40

Downloaded from www.Manualslib.com manuals search engine Back-up Lamp
You can reach the back-up lamps by removing the
license plate and reachmg through the opening.
1. Push the tab on the socket and turn it
counterclockwise.

2. Push the bulb in, turn it counterclockwise, then pull
it out.
3. Reverse the steps with a new bulb.
6-41

Downloaded from www.Manualslib.com manuals search engine Sidemarker 1. Turn the socket counterclockwise 1/4 turn and
pull it out.
You can reach the front sidemarker from inside the
engine compartment.
Reach
the rear sidemarker from under the vehicle.
2. Pull the bulb straight out.
3. Reverse the steps with a new bulb.
6-42