lock CHEVROLET CORVETTE 1996 4.G Manual PDF

Downloaded from www.Manualslib.com manuals search engine When to Add Oil
If the oil is at or below the ADD mark, you’ll need to
add some oil. But you must use the right kind. This part
explains what kind of oil to use.
For crankcase capacity,
see “Capacities and Specifications” in the Index.
NOTICE:
Don’t add too much oil. If your engine has so
much oil that the oil level gets above the upper
mark that shows the proper operating range,
your engine could be damaged.
The engine oil fill cap is on
top
of the engine block.
Just fill it enough to put the level somewhere in the
proper operating range. Push the dipstick all the way
back in when you’re through.
6-11

Downloaded from www.Manualslib.com manuals search engine Front Tbrn Signal Lamps
1. Open the hood.
2. Find the socket at the front of the engine
compartment.
3. Turn the socket counterclockwise one-quarter of a
turn and pull it out.
4. Push the bulb in, turn it counterclockwise, then pull
it out.
5. Reverse the steps with a new bulb. The socket has
three large tabs and one small tab. Be sure to line up
the small tab with the small notch in the housing.
6-38

Downloaded from www.Manualslib.com manuals search engine Sidemarker Lamps
L
You can reach the front sidemarker lamp from inside the
engine compartment.
Reach the rear sidemarker lamp from under
the vehicle.
1. Turn the socket counterclockwise one-quarter of a
turn and pull it out.
2. Pull the bulb straight out.
3. Reverse the steps with a new bulb.
6-39

Downloaded from www.Manualslib.com manuals search engine Cornering Lamps
You can reach the front cornering lamp from inside the
engine compartment.
Reach the rear cornering lamp from under the vehicle.
1. Press the tab on the socket, turn it counterclockwise
one-quarter
of a turn and pull it out.
6-40
1_
2. Push the bulb in, turn it counterclockwise, theh pull it out.
3. Reverse the steps with a new bulb.
Fog Lamps
You can reach the fog lamps from under the front bumper.
1. Remove the screw in the access door. Open the door.
2. Turn the bulb base counterclockwise one-eighth of a
3. Disconnect the bulb base from the wiring harness.
4. Reverse the steps with a new bulb.
turn and pull
it out.

Downloaded from www.Manualslib.com manuals search engine Center High-Mounted Stoplamp
You can reach the center high-mounted stoplamp by
removing the license plate and reaching through the
opening.
1. Turn the socket counterclockwise one-quarter of a
turn and pull it out.
2. Push the bulb in, turn it counterclockwise, then pull
it out.
3. Reverse the steps with a new bulb.
6-41

Downloaded from www.Manualslib.com manuals search engine Rear Turn Signal and Taillamps
I
I
1. Remove the screws.
2. Pull the lens out.
3. Push the bulb in, turn it counterclockwise, then pull
it out.
4. Reverse the steps with a new bulb. To prevent water
from getting inside the lens, make sure the lens seal
is properly positioned.
6-42

Downloaded from www.Manualslib.com manuals search engine Back-up Lamps
I
You can reach the back-up lamps by removing the
license plate and reaching through the opening.
1. Push the tab on the socket and turn it
counterclockwise.
2. Push the bulb in, turn it counterclockwise, then pull
it out.
3. Reverse the steps with a new bulb.
6-43

Downloaded from www.Manualslib.com manuals search engine Fuses and Circuit Breakers
The wiring circuits in your vehicle are protected from
short circuits by a combination of maxi-fuses,
mini-fuses and circuit breakers. This greatly reduces
the chance
of fires caused by electrical problems.
Look at the silver-colored band inside the fuse. If the
band is broken or melted, replace the fuse.
Be sure you
replace a bad fuse with a new one of the identical size
and rating.
If you ever have a problem
on the road and don’t have
a spare fuse,
you can borrow one that has the same
amperage. Just pick some feature of your vehicle that
you can get along without
-- like the radio or cigarette
lighter
-- and use its fuse, if it is the correct amperage.
Replace it as soon as you can.
Instrument Panel Fuse Block
The interior fuse center is on the right side of your
instrument panel. Turn the knob and pull the door
to
access the fuses.
6-65

Downloaded from www.Manualslib.com manuals search engine t'
1c 7 21 7 3c 7 4c 7 5c 7 NC MDL BTSI WIPER RDO IGN. HTD MIR CIRCUIT
6C 7 71. 7 8C 7 9c 71oc 7 TAIL HORN STOP/HAZ CRANK CRANK
CLUTCH AIR BAG P/N
11c 7 12c 7 131 7 l4C 7 151 7
15c 7 171 7 18C 7 19c 7c 7
RH ILLUM LH ILLUM CNSL ILLUM F.P. 1 A/TRANS
CCMB GENERATOR A/C UTlLllY OXYGEN SEN
CLUTCH
ZC 7=c 7 =C 724c 725c 7
=c 727c 728C 7c 7c 7
ENG2 lNJl INJ 2 TURN COIL
P.K.E. CLUSTER BACKUP FAN ENG
1
31c 7-c 7=c 7c IbC 7
=E 7 37c 7 =c 7 391 74oc 7
4lC 742C 7C JC 7
PWR MIRROR CRUISE E.C.M. AIR BAG CCMl
RHCTSY LHCTSY L.C.D. CCMP RDOBATT
SPORT SEAT PWR LOCK NC PROG CIGAR HATCH
BREAKERS

ml
POWER SEAT
Two maxi -fuse blocks
are located under hood
near battery.
POWER WINDOW
N
P
6-66

Downloaded from www.Manualslib.com manuals search engine Fuse
1
2
3
4
5
6
7
8
9
10
11
12
Usage
Heater, A/C Programmer
Brake-Transmission Shift
Interlock
Windshield WiperNasher Switch
Assembly
Radio Receiver (Ignition)
Heated Mirrors, Heater
and A/C
Control Head, Heater and A/C
Programmer
Light Switch, Daytime Running
Lamps Module
Horn Relay
Hazard Flashers, Brake Switch
Crank-Air Bag
Crank-Park/Neutral Switch
(Automatic), Clutch Switch
(Manual)
Usage
Console Illumination
Fuel Pump
1
Automatic Transmission
Central Control Module, Daytime
Running Lamps Module
Generator
A/C .Compressor Clutch, Heater
and A/C Control Head, Heater and
A/C Programmer, Rev Defog
Relay
Accessory Plug
Heated Oxygen Sensors
Real Time Damping Module, ABS
Module, HVAC Solenoid
Assembly
Injectors
#1,4,6,7
Injectors #2,3,5, 8
Turn Signal Flashers
Ignition Coil and Ignition Coil
Module
ti47
RH Illumination
LH Illumination
Fuse
13
14
15
16
17
18
19
20
21
22
23 24
25