sunroof CHEVROLET DYNASTY 1993 User Guide

AG-VEHICLE BODY COMPONENT SERVICE INDEX
page page
A-Pillar and Roof Rail Mouldings ............. 61
Body Side Applique ....................... 60
Body Side Mouldings ...................... 60
Closure Panel Sight Shield ................. 52
Cowl Cover ............................. 54
Door Glass ............................. 58
Door Glass Opening Moulding ............... 59
Door Latch ............................. 57
Door Opening Scuff Plates ................. 61
Door Opening Weatherstrips ................ 60
Door Trim Panel ......................... 56
Floor Carpet ............................ 64
Front Center Console ..................... 64
Front Door and Hinge ..................... 56
Front Door Silencer and Water Shield ......... 56
Front End Splash Shields .................. 54
Front Fender ............................ 55
Front Seat Belts ......................... 61
Front Seats ............................. 63
Fuel Fill Door ........................... 68
Glass Run Weatherstrip ................... 58
Head Lining ............................. 65
Hood and Hinges ........................ 52
Hood Applique .......................... 54
Hood Latch and Release Cable .............. 53
Hood Latch Safety Catch .................. 54
Inside Latch Release Handle ................ 59 Lift Gate
............................... 67
Lift Gate and Fuel Fill Door Release Cables .... 69
Lift Gate Latch and Striker ................. 68
Lift Gate Lock Cylinder .................... 68
Lift Gate Prop Cylinder .................... 67
Lift Gate Spoiler ......................... 67
Lift Gate Trim ........................... 61
Lower Quarter Trim Panel .................. 61
Lower Tail Panel Trim Cover ................ 61
Manual Window Lift Plate and Guide .......... 58
Manual Window Regulator .................. 57
Manual Window Regulator .................. 58
Outside Door Latch Release Handle .......... 58
Overhead Console ........................ 65
Power Door Lock Actuator .................. 59
Power Window Regulator .................. 57
Quarter Glass Module ..................... 66
Quarter Panel Spoiler ..................... 67
Rear Seat Belts .......................... 62
Rear Seats ............................. 63
Rear Window Glass ...................... 65
Roof Seam Molding ....................... 66
Side View Mirror ......................... 59
Sunroof Lift Control ....................... 65
Tail Lamp Closure Panel ................... 69
Upper Quarter Trim Panel .................. 61
CLOSURE PANEL SIGHT SHIELD
REMOVAL (FIG. 1)
(1) Raise hood to open position.
(2) Loosen twist fasteners holding headlamp covers
to fascia. (3) Disengage hook and loop fasteners holding
sight shield to radiator closure panel. (4) Remove push-in fasteners holding sight shield
to bumper fascia. (5) Separate sight shield from vehicle.
INSTALLATION
Reverse the preceding operation.
HOOD AND HINGES
HOOD REMOVAL (FIG. 2)
(1) Raise hood to full up position.
(2) Lift front edge of cowl cover on the right side of
the windshield washer bottle and disconnect the un-
der hood lamp wire connector. (3) Mark all bolt and hinge attachment locations
with a grease pencil or other suitable device to pro-
vide reference marks for installation. When install-
ing hood, align all marks and secure bolts. The hood should be aligned to 4 mm (0.160 in.) gap to the front
fenders and flush across the top surfaces along fend-
ers. (4) Remove the top hood to hinge attaching bolts
and loosen the bottom bolts until they can be re-
moved by hand. (5) With assistance of a helper at the opposite side
of the vehicle to support the hood, remove the bottom
hood to hinge attaching bolts. Separate the hood
from the vehicle.
Fig. 1 Closure Panel Sight Shield
23 - 52 AG-BODY Ä

OVERHEAD CONSOLE
REMOVAL (FIG. 33)
(1) Remove screws holding overhead console to re-
inforcement bracket. (2) Slide overhead console rearward to separate re-
inforcement bracket retainer tab from console. (3) Lower console from roof and disconnect wire
connectors.
INSTALLATION
Reverse The preceding operation.
HEAD LINING
REMOVAL
(1) Disconnect battery negative cable.
(2) Pull dome lamp downward to disengage from
retaining ring in head lining. Separate lens from
lamp body and remove bulb. Separate bulb holder
from lamp body. Remove attaching screw holding re-
taining ring to roof bow, if equipped. (3) Remove screws holding coat hooks to roof above
quarter panels. (4) Remove roof rail and A-pillar mouldings.
(5) Remove screws holding sun visors to roof
header and disconnect wire connector, if equipped.
Remove inboard sun visor hangers. (6) Remove overhead console, if equipped.
(7) Pull front reading lamp downward to disengage
from retaining ring in head lining and disconnect
wire connector. Remove screws holding retaining
ring to roof header, if equipped. (8) Remove pinch welt holding headlining to sun
roof opening, if equipped. (9) Remove screws holding lift gate opening header
moulding to rear roof header. Separate moulding
from header. (10) Remove one quarter trim panel as necessary
to clear head lining removal path. (11) Remove head lining from vehicle.
INSTALLATION
Reverse the preceding operation.
SUNROOF LIFT CONTROL
REMOVAL (FIG. 34)
(1) Remove sunroof glass panel. Refer to Owners
manual for proper procedures. (2) Remove pinch welt holding head lining to edge
of sunroof opening. (3) Remove trim ring from tilt control handle.
(4) Remove screws holding tilt control handle to
tilt control. Separate handle from control. (5) Remove nuts holding lift control to roof panel.
Separate lift control from roof.
INSTALLATION
Reverse the preceding operation.
REAR WINDOW GLASS
The rear window moulding often cannot be sal-
vaged after removal operation is completed. Verify
moulding availability from the parts supplier before
removing moulding.
REMOVAL (FIG. 35)
(1) Remove rear window moulding.
(2) Remove lift gate trim as necessary to gain ac-
cess to rear window defogger wire connector and
ground screw, if equipped.
WARNING: WEAR EYE AND HAND PROTECTION
WHEN HANDLING SAFETY GLASS. PERSONAL IN-
JURY CAN RESULT.
CAUTION: Do not damage body or trim finish when
cutting out glass or applying fence primer.
(3) Cut the urethane around the perimeter of the
back window glass. Refer to Windshield section of
this group for proper procedures. (4) Separate the rear window from the vehicle.
INSTALLATION
(1) Prepare the work area, window fence, and glass
the same way as described in the Windshield section
of this group. (2) Place the fence spacers at the locations shown
(Fig. 35). (3) Apply a 10 mm (0.4 in.) bead of urethane
around the perimeter of the glass. (4) Install the glass in the same manner described
in the Windshield section of this group. (5) Install the rear window moulding. Apply 50
mm (2 in.) masking tape over moulding to assure
alignment. (6) Connect rear window defogger wiring and in-
stall lift gate trim.
Fig. 33 Overhead ConsoleÐTypical
Ä AG-BODY 23 - 65

(7) After urethane has cured remove masking tape
and water test to verify repair. Verify rear window
defogger operation, refer to Group 8N, Rear Window
Defogger.QUARTER GLASS MODULE
REMOVAL (FIG. 36)
(1) Remove quarter trim panel as necessary to
gain access to quarter glass module. (2) Remove nuts holding quarter glass module to
quarter glass opening. (3) Cut urethane bonding around perimeter of
quarter glass opening fence. (4) Push quarter glass module from quarter glass
opening. (5) Separate module from vehicle.
INSTALLATION
(1) Clean hardened urethane from quarter glass
opening fence and glass module, if module replace-
ment is not required. (2) Prepare fence and module using method de-
scribed in the Windshield section of this group. (3) Reverse the removal operation.
ROOF SEAM MOLDING
REMOVAL (FIG. 37)
(1) Remove upper quarter trim panel.
(2) Remove head lining as necessary to gain access
to inside roof panel. (3) Remove seal nut holding seam molding to roof
panel.
Fig. 34 Sunroof
Fig. 35 Lift Gate Window Glass
23 - 66 AG-BODY Ä