key CHEVROLET VOLT 2012 1.G User Guide

Black plate (3,1)Chevrolet Volt Owner Manual - 2012
Keys, Doors, and Windows 2-3
If there is a decrease in the RKE
operating range:
.Check the distance. The
transmitter may be too far from
the vehicle.
.Check the location. Other
vehicles or objects may be
blocking the signal.
.Check the transmitter's battery.
See“Battery Replacement” later
in this section.
.If the transmitter is still not
working correctly, see your
dealer or a qualified technician
for service.
Remote Keyless Entry
(RKE) System Operation
The RKE transmitter functions will
work up to 60 m (195 ft) away from
the vehicle.
Keep in mind that other conditions,
such as those previously stated,
can impact the performance of the
transmitter.
K(Unlock): Press once to unlock
the driver door. Press a second time
within five seconds to unlock all
doors.
The hazard warning lamps will flash
twice each time the button is
pressed and the anti-theft alarm
system will be disarmed. See
Anti-theft Alarm System on
page 2‑15. On some models, pressing and
holding
Kwill open all of the
vehicle's windows. See Power
Windows on page 2‑19. This feature
can be disabled by a service
technician.
Q(Lock): Press to lock all doors.
The hazard warning lamps will flash
once and the anti-theft alarm system
will be armed. See Anti-theft Alarm
System on page 2‑15.
If the driver door is open when
Qis
pressed, all doors lock and then
the driver door will unlock if the
Unlocked Door Anti Lock Out
feature is enabled through the
vehicle personalization. See
“Unlocked Door Anti Lock Out”
under Vehicle Personalization on
page 5‑56 for more information.
This may vary based on vehicle
personalization.

Black plate (4,1)Chevrolet Volt Owner Manual - 2012
2-4 Keys, Doors, and Windows
7(Panic Alarm):Press and
release one time to locate the
vehicle. The exterior lamps flash
and the horn chirps three times.
Press and hold for three seconds to
sound the panic alarm. The horn
sounds and the turn signals flash for
30 seconds. Press again to cancel
the panic alarm.
B(Remote Start): PressQand
then press and hold
Bwithin
five seconds to start the vehicle's
heating or air conditioning systems
and rear window defogger from
outside the vehicle using the RKE
transmitter. See Remote Start on
page 2‑8 for more information. The auto heated seats, if equipped,
can be programmed to come on
when the vehicle is remotely
started. See
Vehicle Personalization
on page 5‑56 for more information.
Also see “Auto Heated Seats” under
Heated Front Seats on page 3‑6.
A(Charge Port Door): Press to
open the charge port door. See
Plug-In Charging on page 9‑48 for
more information.
Keyless Access Operation
With the keyless access system,
you can lock and unlock the doors
and access the hatch without
removing the RKE transmitter from
your pocket, purse, briefcase, etc.
The RKE transmitter should be
within 1 m (3 ft) of the door or hatch
being opened. Keyless Unlocking/Locking from
the Driver Door
When the doors are locked and the
RKE transmitter is within 1 m (3 ft) of
the driver door handle, pressing the
lock/unlock button on the driver door
handle will unlock the driver door.
If the lock/unlock button is pressed
again within five seconds, all
passenger doors will unlock.
Pressing the lock/unlock button will
cause all doors to lock if any of the
following occur:.It has been more than
five seconds since the first
lock/unlock button press.
.Two lock/unlock button presses
were used to unlock all doors.
.Any vehicle door has opened
and all doors are now closed.
The vehicle can be customized to
always unlock all doors on the first
lock/unlock button press.

Black plate (5,1)Chevrolet Volt Owner Manual - 2012
Keys, Doors, and Windows 2-5
Keyless Unlocking/Locking from
Passenger Doors
When the doors are locked and the
RKE transmitter is within 1 m (3 ft) of
the door handle, pressing the lock/
unlock button on that door handle
will unlock all doors. Pressing the
lock/unlock button will cause all
doors to lock if any of the following
occur:
.After the lock/unlock button was
used to unlock all doors.
.After any vehicle door has
opened and all doors are now
closed.
Keyless Hatch Opening
Press the button on the underside of
the hatch and lift up to open if the
RKE transmitter is within range and
the doors are locked. If the doors
are unlocked, the transmitter is not
required to open the hatch.
Programming Transmitters to
the Vehicle
Only RKE transmitters programmed
to this vehicle will work. If a
transmitter is lost or stolen, a
replacement can be purchased and
programmed through your dealer.
When the replacement transmitter is
programmed to this vehicle, all
remaining transmitters must also be
reprogrammed. Any lost or stolen
transmitters will no longer work
once the new transmitter is
programmed. Each vehicle can
have up to five transmitters matched
to it. Programming with a Recognized
Transmitter
A new transmitter can be
programmed to the vehicle when
there is one recognized transmitter.
For vehicles sold in Canada, two
recognized transmitters are required
to program a new transmitter. To
program, the vehicle must be off
and all of the transmitters, both
currently recognized and new, must
be in the vehicle.
1. Place the recognized
transmitter(s) in the cupholder.
2. Insert the vehicle key of the new transmitter into the key lock
cylinder on the outside of the
driver door and turn the key to
the unlock position five times
within 10 seconds.
The Driver Information Center
(DIC) displays READY FOR
REMOTE #2, 3, 4 OR 5.

Black plate (6,1)Chevrolet Volt Owner Manual - 2012
2-6 Keys, Doors, and Windows
3. Remove the rubber mat in theinstrument panel storage.
Extend the key blade on the new
transmitter and insert the key
blade into the transmitter slot.
4. Press and hold the POWER
O
button on the center stack for
two seconds. When the
transmitter is programmed, the
DIC will show that it is ready to
program the next transmitter. 5. Remove the transmitter from the
transmitter slot and press
Kon
the transmitter.
To program additional
transmitters, repeat Steps 3
through 5.
When all additional transmitters
are programmed, press and hold
the POWER
Obutton for
10 seconds to exit
programming mode.
Programming without a
Recognized Transmitter
Non-Canadian (U.S.) owners are
permitted to program a new
transmitter to their vehicle when a
recognized transmitter is not
available. The Canadian regulations
require that Canadian owners see
their dealer for programming new
transmitters when two recognized
transmitters are not available. If there are no currently recognized
transmitters available, follow this
procedure to program up to five
transmitters. This procedure will
take approximately 30 minutes to
complete. The vehicle must be off
and all of the transmitters must be in
the vehicle.
1. Insert the vehicle key of the
transmitter into the key lock
cylinder on the outside of the
driver door and turn the key to
the unlock position five times
within 10 seconds.
The Driver Information Center
(DIC) displays REMOTE LEARN
PENDING, PLEASE WAIT.

Black plate (7,1)Chevrolet Volt Owner Manual - 2012
Keys, Doors, and Windows 2-7
2. Wait for 10 minutes until the DICdisplays PRESS START
BUTTON TO LEARN and then
press the POWER
Obutton on
the center stack.
The DIC display will again show
REMOTE LEARN PENDING,
PLEASE WAIT.
3. Repeat Step 2 two more times. After the third time, all previously
known transmitters will no longer
work with the vehicle. Remaining
transmitters can be programmed
during the next steps.
The DIC display should now
show READY FOR
REMOTE #1.
4. Remove the rubber mat in theinstrument panel storage.
Extend the key blade on the new
transmitter and insert the key
blade into the transmitter slot.
5. Press and hold the POWER
O
button for two seconds. When
the transmitter is programmed,
the DIC will show that it is ready
to program the next transmitter. 6. Remove the transmitter from the
transmitter slot and press
Kon
the transmitter.
To program additional
transmitters, repeat Steps 4
through 6.
When all additional transmitters
are programmed, press and hold
the POWER
Obutton for
10 seconds to exit
programming mode.
Starting the Vehicle with a Low
Transmitter Battery
If the transmitter battery is weak, the
DIC may display NO REMOTE
DETECTED when you try to start
the vehicle. The REPLACE
BATTERY IN REMOTE KEY
message may also be displayed at
this time.

Black plate (8,1)Chevrolet Volt Owner Manual - 2012
2-8 Keys, Doors, and Windows
To start the vehicle:
1. Open the instrument panelstorage and remove the
rubber mat.
2. Extend the key blade and placethe blade into the slot.
3. With the vehicle in P (Park) or N (Neutral), press the brake
pedal and the POWER
Obutton
on the center stack. See Power
Button on page 9‑18 for
additional information. Replace the transmitter battery as
soon as possible.
Battery Replacement
Notice:
When replacing the
battery, do not touch any of the
circuitry on the transmitter. Static
from your body could damage the
transmitter.
To replace the battery:
1. Extend the key blade and open the battery cover on the back of
the unit.
2. Remove the used battery. Avoid touching the circuit board to
other components.
3. Insert the new battery, positive side facing down toward
the base.
4. Reassemble the battery cover.
5. Check the operation of the transmitter with the vehicle.
Remote Start
This feature starts the heating or air
conditioning systems and rear
window defogger from outside the
vehicle. Use remote start to heat or
cool the interior when the vehicle is
plugged in to maximize the electric
range by utilizing electricity from the
electrical outlet. Normal operation of
the system will return after the
vehicle has been turned on.
B(Remote Start): This button is
on the RKE transmitter.
During remote start:
.The climate control system will
typically default to the last
climate settings. If the fan is off
or if Fan Only was selected, the
air conditioning or heat will turn
on as needed. See Automatic
Climate Control System on
page 8‑1 for more information.

Black plate (9,1)Chevrolet Volt Owner Manual - 2012
Keys, Doors, and Windows 2-9
.If the vehicle has heated seats,
and this feature has been
enabled through vehicle
personalization, the heated
seats will turn on during colder
outside temperatures. See
“Remote Start Heated Seats”
underHeated Front Seats on
page 3‑6 and“Remote Start
Auto Heated Seats” under
Vehicle Personalization on
page 5‑56 for additional
information.
.The rear defogger will turn on
during colder outside
temperatures.
.Selecting1during colder
outside temperatures before
shutting the vehicle off will help
windshield clearing.
.Shutting the vehicle off in ECO
Mode without
1selected will
minimize the impact to electric
range. Shutting the vehicle off in
other modes will maximize
heating or air conditioning.
.The engine may start to provide
energy for heating and cooling,
independent of the vehicle being
plugged in or completely
charged. Engine Assisted
Heating operation, if available,
can be personalized. See
“Engine Assisted Heating” under
Vehicle Personalization on
page 5‑56.
.Vehicle range may decrease if
the vehicle is not plugged into
an electrical outlet. If the vehicle
is plugged in, much of the
energy needed to support this
feature will be provided from the
utility, not from the high voltage
battery. Laws in some communities may
restrict the use of features that
remotely start the engine. For
example, some laws may require a
person using the remote start
feature to have the vehicle in view
when doing so. Check local
regulations for any requirements on
remote starting of vehicles.
With the remote start feature, the
RKE transmitter functions will have
an increased range of operation.
However, the range may be less
while the vehicle is running.
Other conditions can affect the
performance of the transmitter. See
Remote Keyless Entry (RKE)
System on page 2‑2
for additional
information.

Black plate (10,1)Chevrolet Volt Owner Manual - 2012
2-10 Keys, Doors, and Windows
Activating the Remote Start
To heat or cool the passenger
compartment using remote start:
1. Aim the RKE transmitter at thevehicle.
2. Press
Qon the RKE transmitter;
the doors will lock.
3. Within five seconds, press and hold
Buntil the turn signal
lamps flash, or for approximately
four seconds. Pressing
Bagain
during a remote start will turn the
feature off.
Remote start will automatically shut
off after 10 minutes unless a time
extension is done.
While the remote start is active, the
parking lamps will turn on and
remain on.
After entering the vehicle during a
remote start, press the POWER
O
button on the center stack with the
brake pedal applied to operate as
normal. The remote start can be initiated
two separate times between driving.
For each remote start, the
passenger compartment will be
heated or cooled for 10 minutes.
Extending the Time
To extend the time of the first
remote start, repeat the steps for
activating remote start. Remote start
can only be extended one time
between driving.
Canceling Remote Start
To cancel a remote start, do any of
the following:
.Aim the RKE transmitter at the
vehicle and press and hold
B
until the parking lamps turn off.
.Turn on the hazard warning
flashers.
.Press the POWERObutton on
the center stack, with the brake
pedal applied, then press the
POWER
Obutton again to turn
the vehicle off.
Conditions in Which Remote
Start May Not Work
Conditions in which a remote start
may not occur include:
.An open hood.
.Vehicle propulsion system fault
conditions, including an
emission control system
malfunction.
.High voltage battery fault
conditions.
A second remote start or extension
will not occur if the fuel level is low.

Black plate (11,1)Chevrolet Volt Owner Manual - 2012
Keys, Doors, and Windows 2-11
During a remote start, conditions in
which a remote start may be
canceled include:
.Vehicle propulsion system or
high voltage battery fault
conditions.
.Low engine oil pressure.
.Engine coolant temperature that
is too high.
Door Locks
{WARNING
Unlocked doors can be
dangerous.
.Passengers, especially
children, can easily open the
doors and fall out of a moving
vehicle. The chance of being
thrown out of the vehicle in a
crash is increased if the
doors are not locked. So, all
passengers should wear
safety belts properly and the(Continued)
WARNING (Continued)
doors should be locked
whenever the vehicle is
driven.
.Young children who get into
unlocked vehicles may be
unable to get out. A child can
be overcome by extreme heat
and can suffer permanent
injuries or even death from
heat stroke. Always lock the
vehicle whenever leaving it.
.Outsiders can easily enter
through an unlocked door
when slowing or stopping the
vehicle. Lock the doors to
help prevent this from
happening. Keyless Access:
The RKE
transmitter must be within 1 m (3 ft)
of the door being opened.
To unlock the door from the driver
door, press the lock/unlock button
on the door handle. Press again
within five seconds to unlock all
passenger doors.

Black plate (12,1)Chevrolet Volt Owner Manual - 2012
2-12 Keys, Doors, and Windows
To lock the doors, press the lock/
unlock button if:
.More than five seconds have
passed.
.The lock/unlock button was used
to unlock all doors.
.All doors are closed.
To unlock all doors from the
passenger door, press the lock/
unlock button on the door handle.
To lock the doors, press the lock/
unlock button if:
.The lock/unlock button was used
to unlock all doors.
.All doors are closed.
The Keyless Access can be
programmed to unlock all doors on
the first lock/unlock press from the
driver door. See Vehicle
Personalization on page 5‑56. Remote Keyless Entry (RKE):
The RKE transmitter must be within
60 m (195 ft) of the vehicle.
K:
Press to unlock.
Q:Press to lock.
See Remote Keyless Entry (RKE)
System Operation on page 2‑3.
Key: To unlock or lock the door,
turn the key left or right.
Inside the Vehicle: Pull up or push
down on the door lock knob. Pull
once on the door handle to unlock
the door and a second time to open
the door. Push the power door lock
switch. See Power Door Locks on
page 2‑12.
Power Door Locks
The power door lock switches are
on the center stack.
K(Unlock): Press to unlock the
doors.
Q(Lock): Press to lock the doors.