display CHRYSLER CARAVAN 2000 Workshop Manual

TEST TC-62AREPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL HIGH EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
DOES THE DRB
START TEST USING THE DRB, DISPLAY "INTAKE YES CONTINUE TEST
TC-62A. ERASE CODES. AIR TEMPERATURE TC-62A ON THE
SENSOR HIGH NEXT PAGE.
EXCEEDED"?
NO
USE THE SCHEMATIC AS DOES THE DRB REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB DISPLAY "INTAKE YES OR CONNECTOR THAT
THE INTAKE AIR DISPLAY. AIR TEMPERATURE CAUSED THE CODE TO
TEMPERATURE SENSOR SENSOR HIGH SET.*
CONNECTOR & HARNESS. EXCEEDED"?
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
217
ProCarManuals.com

TEST TC-62ACONTINUED - REPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL HIGH
EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-62A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS BOOST PRESSURE
PAGE. SENSOR HARNESS
CONNECTOR.**
WITH A JUMPER WIRE, TURN IGNITION ON.
DISCONNECT THE ECM REMOVE THE DIESEL CONNECT DIESEL POWER
HARNESS POWER RELAY.** RELAY CONN. CAVITIES USE A VOLTMETER IN
CONNECTORS.** 30 AND 87 (IN PDC). THE FOLLOWING
FIG.1 STEP.
MEASURE THE IAT REPAIR THE INTAKE
SENSOR SIGNAL IS THE VOLTAGE YES AIR TEMPERATURE
CIRCUIT. ABOVE 1.0 VOLT? SENSOR SIGNAL
CIRCUIT FOR A
FIG.2 SHORT TO VOLTAGE.*
NO
KEY OFF. USING AN OHMMETER, REPAIR THE OPEN
MEASURE THE IAT IS THE RESISTANCE NO INTAKE AIR
REMOVE THE JUMPER SENSOR SIGNAL BELOW 5.0 OHMS? TEMPERATURE SENSOR
WIRE. CIRCUIT. SIGNAL CIRCUIT.*
FIG.3
YES
CONNECT A JUMPER DOES THE DRB
BETWEEN THE INTAKE WITH THE DRB, DISPLAY "INTAKE YES REPLACE THE BOOST
AIR TEMP SENSOR ERASE AND THEN AIR TEMPERATURE PRESSURE SENSOR.*
SIGNAL AND SENSOR READ CODES. SENSOR LOW
GROUND CKT. FIG.1 EXCEEDED"?
NO
MOVE THE JUMPER DOES THE DRB
WIRE FROM THE WITH THE DRB, READ DISPLAY "INTAKE YES REPAIR THE OPEN
SENSOR GROUND TO CODES. AIR TEMPERATURE SENSOR GROUND
AN ENGINE GROUND. SENSOR LOW CIRCUIT.*
EXCEEDED"?
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
219
ProCarManuals.com

TEST TC-63AREPAIRING - INTAKE AIR TEMPERATURE SENSOR SIGNAL LOW EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
DOES THE DRB
START TEST WITH THE DRB, DISPLAY "INTAKE YES CONTINUE TEST
TC-63A. ERASE CODES. AIR TEMPERATURE TC-63A ON THE
SENSOR LOW NEXT PAGE.
EXCEEDED"?
NO
USING THE SCHEMATIC, DOES THE DRB REPAIR THE HARNESS
WIGGLE THE INTAKE MONITOR THE DRB DISPLAY "INTAKE YES OR CONNECTOR THAT
AIR TEMP SENSOR DISPLAY. AIR TEMPERATURE CAUSED THE CODE TO
CONNECTOR & HARNESS. SENSOR LOW SET.*
FIG.1 EXCEEDED"?
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
221
ProCarManuals.com

TEST TC-72AREPAIRING - NEEDLE MOVEMENT SENSOR SRC HIGH EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH THE DRB ERASE TURN IGNITION ON AND
START TEST CODES. TURN READ CODES. DOES THE YES CONTINUE TEST
TC-72A. IGNITION OFF FOR DRB DISPLAY "NEEDLE TC-72A ON THE
10 SECONDS. MOVEMENT SENSOR SRC NEXT PAGE.
HIGH EXCEEDED"?
NO
USING THE SCHEMATIC DOES THE DRB REPAIR THE HARNESS
AS A GUIDE, WIGGLE MONITOR THE DRB DISPLAY "NEEDLE YES OR CONNECTOR THAT
THE SENSOR CONNECTOR DISPLAY. MOVEMENT SENSOR CAUSED THE CODE TO
& HARNESS. SRC HIGH SET.*
FIG.1 EXCEEDED"?
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
225
ProCarManuals.com

TEST TC-72ACONTINUED - REPAIRING - NEEDLE MOVEMENT SENSOR SRC HIGH EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-72A KEY OFF.
CONTINUED FROM DISCONNECT THE
THE PREVIOUS NEEDLE MOVEMENT
PAGE. SENSOR HARNESS
CONNECTOR.**
CONNECT A JUMPER DOES THE DRB
BETWEEN THE NEEDLE WITH THE DRB, READ DISPLAY "NEEDLE YES REPLACE THE NEEDLE
SENSOR SIGNAL AND CODES. MOVEMENT SENSOR MOVEMENT SENSOR.*
SENSOR GROUND CKT. SRC LOW EXCEEDED"?
FIG.1
NO
MOVE THE JUMPER DOES THE DRB
WIRE FROM THE WITH THE DRB, READ DISPLAY "NEEDLE YES REPAIR THE OPEN
SENSOR GROUND TO CODES. MOVEMENT SENSOR SENSOR GROUND
AN ENGINE GROUND. SRC LOW EXCEEDED"? CIRCUIT.*
NO
KEY OFF. WITH A JUMPER WIRE,
DISCONNECT THE ECM REMOVE THE DIESEL CONNECT DIESEL POWER
HARNESS POWER RELAY. RELAY CONN. CAVITIES
CONNECTORS.** 30 AND 87 (IN PDC).
FIG.2
KEY ON. MEASURE REPAIR THE SHORT
USE A VOLTMETER IN THE NEEDLE IS THE VOLTAGE YES TO VOLTAGE ON THE
THE FOLLOWING MOVEMENT SENSOR ABOVE 0.5 VOLT? NEEDLE MOVEMENT
STEP. SIGNAL CIRCUIT. SENSOR SIGNAL
FIG.1 CIRCUIT.*
NO
KEY OFF. MEASURE THE NEEDLE
MOVEMENT SENSOR IS THE RESISTANCE YES REPLACE THE ENGINE
USE AN OHMMETER IN SIGNAL CIRCUIT. BELOW 5.0 OHMS? CONTROL MODULE.*
THE FOLLOWING
STEP. FIG.3
NO
REPAIR THE OPEN
NEEDLE MOVEMENT
SENSOR SIGNAL
CIRCUIT.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
227
ProCarManuals.com

TEST TC-73AREPAIRING - NEEDLE MOVEMENT SENSOR SRC LOW EXCEEDED
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
WITH THE DRB, TURN IGNITION ON AND
START TEST ERASE CODES. TURN READ CODES. DOES THE YES CONTINUE TEST
TC-73A. IGNITION OFF FOR DRB DISPLAY " NEEDLE TC-73A ON THE
10 SECONDS. MOVEMENT SENSOR SRC NEXT PAGE.
LOW EXCEEDED"?
NO
USING THE SCHEMATIC, DOES THE DRB REPAIR THE HARNESS
WIGGLE THE NEEDLE MONITOR THE DRB DISPLAY "NEEDLE YES OR CONNECTOR THAT
MOVEMENT SENSOR DISPLAY. MOVEMENT SENSOR CAUSED THE CODE TO
CONNECTOR & HARNESS. SRC LOW EXCEEDED"? SET.*
FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
229
ProCarManuals.com

TEST TC-73ACONTINUED - REPAIRING - NEEDLE MOVEMENT SENSOR SRC LOW EXCEEDED
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
TEST TC-73A DOES THE DRB
CONTINUED FROM DISCONNECT THE DISPLAY "NEEDLE YES REPLACE THE NEEDLE
THE PREVIOUS NEEDLE MOVEMENT MOVEMENT SENSOR MOVEMENT SENSOR.*
PAGE. SENSOR.** SRC HIGH
EXCEEDED"?
NO
KEY OFF. USING AN OHMMETER, REPAIR THE NEEDLE
DISCONNECT THE ECM MEASURE THE NEEDLE IS THE RESISTANCE YES MOVEMENT SENSOR
HARNESS MOVEMENT SENSOR BELOW 5.0 OHMS? SIGNAL CIRCUIT FOR
CONNECTORS.** SIGNAL CIRCUIT TO A SHORT TO
GROUND. FIG.1 GROUND.*
NO
WITH AN OHMMETER NEEDLE MOVEMENT REPAIR THE NEEDLE
MEASURE THE SENSOR SIGNAL IS THE RESISTANCE YES MOVEMENT SENSOR
RESISTANCE BETWEEN CIRCUIT AND SENSOR BELOW 5.0 OHMS? SIGNAL CIRCUIT
THE... GROUND CIRCUIT. SHORTED TO THE
FIG.1 SENSOR GND CIRCUIT.*
NO
REPLACE THE ENGINE
CONTROL MODULE.*
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
231
ProCarManuals.com

TEST TC-75AREPAIRING - REDUNDANT EMERGENCY STOP POWERSTAGE DEFECTIVE
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
START TEST WITH THE DRB,
TC-75A. ERASE CODES.
CYCLE THE IGNITION DOES THE DRB
ON AND OFF SEVERAL WITH THE IGNITION DISPLAY "REDUNDANT YES CONTINUE TEST
TIMES, PAUSING FOR ON ENGINE OFF, EMERG STOP TC-75A ON THE
TEN SECONDS AT KEY READ CODES. POWERSTAGE NEXT PAGE.
ON AND OFF. DEFECTIVE"?
NO
AT THIS TIME THE REVIEW THE CIRCUIT
CONDITION FOR DESCRIPTION FOR A WERE ANY PROBLEMS YES REPAIR AS
SETTING THE CODE PROPER UNDERSTANDING FOUND? NECESSARY.*
IS NOT PRESENT. OF THIS CODE. CHECK
FIG.1 FOR PROBLEMS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
237
ProCarManuals.com

TEST TC-79AREPAIRING - SOLENOID VALVE CONTROLLER OPEN CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON, READ CODES.
START TEST TURN IGNITION OFF. DOES THE DRB DISPLAY YES CONTINUE TEST
TC-79A. WITH THE DRB, "SOLENOID VALVE TC-79A ON THE
ERASE CODES. CONTROLLER OPEN NEXT PAGE.
CIRCUIT"?
NO
USE THE SCHEMATIC AS DOES THE DRB REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB DISPLAY "SOLENOID YES OR CONNECTOR THAT
THE SOLENOID VALVE DISPLAY. VALVE CONTROLLER CAUSED THE CODE TO
CONNECTOR & HARNESS. OPEN CIRCUIT"? SET.*
FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
243
ProCarManuals.com

TEST TC-80AREPAIRING - SOLENOID VALVE CONTROLLER SHORT CIRCUIT
Perform TEST DTC Before Proceeding
*Perform Verification TEST VER-2A. **Check connectors - Clean / repair as necessary.
KEY ON, READ CODES.
START TEST WITH THE DRB, DOES THE DRB DISPLAY YES CONTINUE TEST
TC-80A. ERASE CODES. TURN "SOLENOID VALVE TC-80A ON THE
IGNITION OFF. CONTROLLER SHORT NEXT PAGE.
CIRCUIT"?
NO
USE THE SCHEMATIC AS DOES THE DRB REPAIR THE HARNESS
A GUIDE AND WIGGLE MONITOR THE DRB DISPLAY "SOLENOID YES OR CONNECTOR THAT
THE SOLENOID VALVE DISPLAY. VALVE CONTROLLER CAUSED THE CODE TO
CONNECTOR & HARNESS. SHORT CIRCUIT"? SET.*
FIG.1
NO
AT THIS TIME, THE USING THE
CONDITION REQUIRED SCHEMATIC AS A WERE ANY PROBLEMS YES REPAIR AS
TO SET THE CODE IS GUIDE, INSPECT THE FOUND? NECESSARY.*
NOT PRESENT. WIRING AND
FIG.2 CONNECTORS.
NO
REFER TO GENERAL
INFORMATION 3.3.2 YES
FOR ADDITIONAL TEST COMPLETE.*
INFORMATION ON
INTERMITTENT CODES.
T
R
O
U
B
L
E
C
O
D
E
T
E
S
T
S
247
ProCarManuals.com