air suspension CHRYSLER CARAVAN 2005 Owner's Manual

OXYGEN SENSOR HEATER MONITOR (SBEC)
DESCRIPTIONÐIf there is an oxygen sensor
(O2S) DTC as well as a O2S heater DTC, the O2S
heater fault MUST be repaired first. After the O2S
fault is repaired, verify that the heater circuit is
operating correctly.
The voltage readings taken from the O2S are very
temperature sensitive. The readings are not accurate
below 300ÉC. Heating of the O2S is done to allow the
engine controller to shift to closed loop control as
soon as possible. The heating element used to heat
the O2S must be tested to ensure that it is heating
the sensor properly.
The heater element itself is not tested directly. The
sensor output is used to test the heater by isolating
the effect of the heater element on the O2S output
voltage from the other effects. The resistance is nor-
mally between 100 ohms and 4.5 megaohms. When
oxygen sensor temperature increases, the resistance
in the internal circuit decreases. The PCM sends a 5
volts biased signal through the oxygen sensors to
ground this monitoring circuit. As the temperature
increases, resistance decreases and the PCM detects
a lower voltage at the reference signal. Inversely, as
the temperature decreases, the resistance increases
and the PCM detects a higher voltage at the refer-
ence signal. The O2S circuit is monitored for a drop
in voltage.
OPERATIONÐThe Oxygen Sensor Heater Moni-
tor begins after the ignition has been turned OFF
and the O2 sensors have cooled. The PCM sends a 5
volt bias to the oxygen sensor every 1.6 seconds. The
PCM keeps it biased for 35 ms each time. As the sen-
sor cools down, the resistance increases and the PCM
reads the increase in voltage. Once voltage has
increased to a predetermined amount, higher than
when the test started, the oxygen sensor is cool
enough to test heater operation.
When the oxygen sensor is cool enough, the PCM
energizes the ASD relay. Voltage to the O2 sensor
begins to increase the temperature. As the sensor
temperature increases, the internal resistance
decreases. The PCM continues biasing the 5 volt sig-
nal to the sensor. Each time the signal is biased, the
PCM reads a voltage decrease. When the PCM
detects a voltage decrease of a predetermined value
for several biased pulses, the test passes.
The heater elements are tested each time the
engine is turned OFF if all the enabling conditions
are met. If the monitor fails, the PCM stores a
maturing fault and a Freeze Frame is entered. If two
consecutive tests fail, a DTC is stored. Because the
ignition is OFF, the MIL is illuminated at the begin-
ning of the next key cycle, after the 2nd failure.Enabling ConditionsÐThe following conditions
must be met for the PCM to run the oxygen sensor
heater test:
²Engine run time of at least 5.1 minutes
²Key OFF power down
²Battery voltage of at least 10 volts
²Sufficient Oxygen Sensor cool down
Pending ConditionsÐThere are not conditions or
situations that prompt conflict or suspension of test-
ing. The oxygen sensor heater test is not run pending
resolution of MIL illumination due to oxygen sensor
failure.
SuspendÐThere are no conditions which exist for
suspending the Heater Monitor.
CATALYST MONITOR
To comply with clean air regulations, vehicles are
equipped with catalytic converters. These converters
reduce the emission of hydrocarbons, oxides of nitro-
gen and carbon monoxide.
Normal vehicle miles or engine misfire can cause a
catalyst to decay. A meltdown of the ceramic core can
cause a reduction of the exhaust passage. This can
increase vehicle emissions and deteriorate engine
performance, driveability and fuel economy.
The catalyst monitor uses dual oxygen sensors
(O2S's) to monitor the efficiency of the converter. The
dual O2S strategy is based on the fact that as a cat-
alyst deteriorates, its oxygen storage capacity and its
efficiency are both reduced. By monitoring the oxy-
gen storage capacity of a catalyst, its efficiency can
be indirectly calculated. The upstream O2S is used to
detect the amount of oxygen in the exhaust gas
before the gas enters the catalytic converter. The
PCM calculates the A/F mixture from the output of
the O2S. A low voltage indicates high oxygen content
(lean mixture). A high voltage indicates a low content
of oxygen (rich mixture).
When the upstream O2S detects a high oxygen
condition, there is an abundance of oxygen in the
exhaust gas. A functioning converter would store this
oxygen so it can use it for the oxidation of HC and
CO. As the converter absorbs the oxygen, there will
be a lack of oxygen downstream of the converter. The
output of the downstream O2S will indicate limited
activity in this condition.
As the converter loses the ability to store oxygen,
the condition can be detected from the behavior of
the downstream O2S. When the efficiency drops, no
chemical reaction takes place. This means the con-
centration of oxygen will be the same downstream as
upstream. The output voltage of the downstream
O2S copies the voltage of the upstream sensor. The
only difference is a time lag (seen by the PCM)
between the switching of the O2S's.
25 - 4 EMISSIONS CONTROLRS
EMISSIONS CONTROL (Continued)

ENGINE OIL PRESSURE - DIAGNOSISAND TESTING, CHECKING ...............9-53
ENGINE, SPECIAL TOOLS - 2.4L ..........9-21
ENGINE, SPECIAL TOOLS - 3.3/3.8L .......9-98
ENGINE, SPECIFICATIONS - 3.3/3.8L ......9-93
ENGINE SPEED SENSOR - DESCRIPTION . . 14-30
ENGINE SPEED SENSOR - OPERATION ....14-30
ENGINE, STANDARD PROCEDURE - HYDROSTATIC LOCKED .............9-10,9-87
ENGINES - DESCRIPTION, ENGINE OIL - DIESEL ..............................0-6
ENGINES - EXPORT - DESCRIPTION, DIESEL ............................. 0-21
ENGINES, INSTALLATION - 2.4L/3.3L/ 3.8L ............................... 24-77
ENGINES, INSTALLATION - 2.5L/2.8L DIESEL ............................ 24-78
ENGINES, REMOVAL - 2.4L/3.3L/3.8L .....24-76
ENGINES, REMOVAL - 2.5L/2.8L DIESEL . . 24-77
ENTRY MODULE - DESCRIPTION, SENTRY KEY REMOTE .................8Q-3
ENTRY MODULE - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE .........8Q-5
ENTRY MODULE - INSTALLATION, SENTRY KEY REMOTE .................8Q-6
ENTRY MODULE - OPERATION, SENTRY KEY REMOTE ........................ 8Q-4
ENTRY MODULE - REMOVAL, SENTRY KEY REMOTE ........................ 8Q-6
ENTRY SYSTEM - DIAGNOSIS AND TESTING, SENTRY KEY REMOTE .........8Q-3
ENTRY TRANSMITTER, DIAGNOSIS AND TESTING - KEYLESS .................. 8N-24
ENTRY TRANSMITTER PROGRAMMING - STANDARD PROCEDURE, REMOTE
KEYLESS ........................... 8N-24
EQUIPMENT, STANDARD PROCEDURE - REFRIGERANT SYSTEM SERVICE ........24-69
ERASING TRANSMITTER CODES, STANDARD PROCEDURE ..............8M-12
EVACUATE, STANDARD PROCEDURE - REFRIGERANT SYSTEM ...............24-70
EVAP CANISTER - INSTALLATION, REAR . . 25-21
EVAP CANISTER - REMOVAL, REAR ......25-20
EVAPORATION CONTROL SYSTEM - OPERATION ......................... 25-11
EVAPORATOR - DESCRIPTION, A/C . 24-80,24-98
EVAPORATOR - INSTALLATION, A/C ......24-81
EVAPORATOR - OPERATION, A/C . . . 24-80,24-98
EVAPORATOR - REMOVAL, A/C ..........24-81
EVAPORATOR, INSTALLATION - REAR A/C............................... 24-100
EVAPORATOR LINE EXTENSION, INSTALLATION - REAR A/C ............24-100
EVAPORATOR LINE EXTENSION, REMOVAL - REAR A/C .................24-99
EVAPORATOR, REMOVAL - REAR A/C .....24-98
EVAPORATOR TEMPERATURE SENSOR - DESCRIPTION ....................... 24-26
EVAPORATOR TEMPERATURE SENSOR - OPERATION ......................... 24-27
EVAP/PURGE SOLENOID - DESCRIPTION . . 25-13
EVAP/PURGE SOLENOID - INSTALLATION . 25-13
EVAP/PURGE SOLENOID - OPERATION ....25-13
EVAP/PURGE SOLENOID - REMOVAL .....25-13
EXCESSIVE EXHAUST SYSTEM NOISE - DIAGNOSIS AND TESTING ..............11-2
EXHAUST MANIFOLD - CLEANING ........9-63
EXHAUST MANIFOLD - INSPECTION .......9-63
EXHAUST MANIFOLD - INSTALLATION .....9-63
EXHAUST MANIFOLD - LEFT - CLEANING . . 9-154
EXHAUST MANIFOLD - LEFT - INSPECTION ........................ 9-155
EXHAUST MANIFOLD - LEFT - INSTALLATION ....................... 9-155
EXHAUST MANIFOLD - LEFT - REMOVAL . . 9-154
EXHAUST MANIFOLD - REMOVAL .........9-63
EXHAUST MANIFOLD - RIGHT - CLEANING .......................... 9-153
EXHAUST MANIFOLD - RIGHT - INSPECTION ........................ 9-153
EXHAUST MANIFOLD - RIGHT - INSTALLATION ....................... 9-153
EXHAUST MANIFOLD - RIGHT - REMOVAL .......................... 9-152
EXHAUST SYSTEM - DESCRIPTION .......11-1
EXHAUST SYSTEM NOISE - DIAGNOSIS AND TESTING, EXCESSIVE ..............11-2EXHAUST SYSTEM RESTRICTION CHECK
- DIAGNOSIS AND TESTING .............11-2
EXHAUST SYSTEM, SPECIAL TOOLS ......11-4
EXHAUST TUBE - INSTALLATION .......24-116
EXHAUST TUBE - REMOVAL ...........24-116
EXHAUSTER - DESCRIPTION, REAR QUARTER PANEL/FENDER AIR ..........23-59
EXHAUSTER - INSTALLATION, REAR QUARTER PANEL/FENDER AIR ..........23-60
EXHAUSTER - REMOVAL, REAR QUARTER PANEL/FENDER AIR ..........23-59
EXPANSION VALVE - DESCRIPTION ......24-81
EXPANSION VALVE - DESCRIPTION, A/C . 24-100
EXPANSION VALVE - OPERATION ........24-81
EXPANSION VALVE - OPERATION, A/C . . . 24-100
EXPANSION VALVE, DIAGNOSIS AND TESTING - FRONT A/C .................24-82
EXPANSION VALVE, DIAGNOSIS AND TESTING - REAR A/C .................24-101
EXPORT - ANTENNA MODULE ..........8A-10
EXPORT - BRAKE ROTOR ...............5-60
EXPORT - DESCRIPTION ................5-63
EXPORT - DESCRIPTION ................0-13
EXPORT - DESCRIPTION ................2-10
EXPORT - DESCRIPTION, ANTENNA MODULE ........................... 8A-10
EXPORT - DESCRIPTION, DIESEL ENGINES ............................ 0-21
EXPORT - DESCRIPTION, DOOR CYLINDER LOCK SWITCH ...............8N-22
EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - DESCRIPTION, QUARTER GLASS INTEGRAL ANTENNA ............8A-13
EXPORT - DOOR CYLINDER LOCK SWITCH ............................ 8N-22
EXPORT - INSTALLATION ...............5-68
EXPORT - INSTALLATION ...............2-11
EXPORT - INSTALLATION, HEADLAMP UNIT .............................. 8L-17
EXPORT - INSTALLATION, HOOD AJAR SWITCH ............................ 8Q-3
EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR SWITCH ..........8N-30
EXPORT - OPERATION, ANTENNA MODULE ........................... 8A-10
EXPORT - OPERATION, DOOR CYLINDER LOCK SWITCH ....................... 8N-22
EXPORT - OPERATION, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - OPERATION, QUARTER GLASS INTEGRAL ANTENNA .................. 8A-13
EXPORT - QUARTER GLASS INTEGRAL ANTENNA .......................... 8A-13
EXPORT - REMOVAL ................... 5-67
EXPORT - REMOVAL ................... 2-11
EXPORT - REMOVAL, HEADLAMP UNIT . . . 8L-17
EXPORT - REMOVAL, HOOD AJAR SWITCH ............................ 8Q-3
EXPORT - REMOVAL, POWER FOLDAWAY MIRROR SWITCH ..........8N-29
EXPORT - STANDARD PROCEDURE, FRONT FOG LAMP UNIT ALIGNMENT ......8L-9
EXPORT - STANDARD PROCEDURE, HEADLAMP UNIT ALIGNMENT ..........8L-15
EXTENSION, INSTALLATION - REAR A/C EVAPORATOR LINE .................. 24-100
EXTENSION, REMOVAL - REAR A/C EVAPORATOR LINE ................... 24-99
EXTENSION TRIM - INSTALLATION, A-PILLAR LOWER .................... 23-79
EXTENSION TRIM - REMOVAL, A-PILLAR LOWER ............................ 23-79
EXTERIOR - DESCRIPTION, LAMPS/ LIGHTING ........................... 8L-2
EXTERIOR - OPERATION, LAMPS/ LIGHTING ........................... 8L-2
EXTERIOR - WARNING, LAMPS/ LIGHTING ........................... 8L-3
EXTERIOR HANDLE - INSTALLATION .....23-22,
23-40
EXTERIOR HANDLE - REMOVAL ....23-21,23-40
EXTERIOR HANDLE SWITCH - DESCRIPTION ....................... 8N-10
EXTERIOR HANDLE SWITCH - INSTALLATION ...................... 8N-10
EXTERIOR HANDLE SWITCH - OPERATION ......................... 8N-10EXTERIOR HANDLE SWITCH - REMOVAL . . 8N-10
EXTERIOR LAMPS, SPECIFICATIONS
......8L-3
EXTERIOR NAME PLATES - ADHESIVE ATTACHED - INSTALLATION ............23-51
EXTERIOR NAME PLATES - ADHESIVE ATTACHED - REMOVAL ................23-51
EXTERIOR NAME PLATES - TAPE ATTACHED - INSTALLATION ............23-51
EXTERIOR NAME PLATES - TAPE ATTACHED - REMOVAL ................23-51
FACTOR SETTING - STANDARD PROCEDURE, PINION .................8E-15
FAILED PARK SWITCH - DIAGNOSIS AND TESTING ............................ 8R-2
FAN - DESCRIPTION, RADIATOR ..........7-29
FAN - INSTALLATION, RADIATOR .........7-30
FAN - OPERATION, RADIATOR ...........7-29
FAN - REMOVAL, RADIATOR .............7-30
FAN MOTOR - DIAGNOSIS AND TESTING, RADIATOR ................... 7-30
FAN RELAY - DESCRIPTION, RADIATOR ....7-31
FAN RELAY - INSTALLATION, RADIATOR . . . 7-31
FAN RELAY - OPERATION, RADIATOR ......7-31
FAN RELAY - REMOVAL, RADIATOR .......7-31
FASCIA - INSTALLATION, FRONT .........13-1
FASCIA - INSTALLATION, REAR ..........13-4
FASCIA - REMOVAL, FRONT .............13-1
FASCIA - REMOVAL, REAR ..............13-4
FASCIA - SCUFF PAD - INSTALLATION, REAR ............................... 13-5
FASCIA - SCUFF PAD - REMOVAL, REAR . . . 13-5
FASTENER TORQUE, SPECIFICATIONS - ABS ................................ 5-91
FASTENER TORQUE, SPECIFICATIONS - BRAKE ...............................5-9
FASTENER TORQUE, SPECIFICATIONS - COLUMN ........................... 19-17
FASTENER TORQUE, SPECIFICATIONS - FRONT SUSPENSION ...................2-3
FASTENER TORQUE, SPECIFICATIONS - POWER STEERING .................... 19-9
FASTENER TORQUE, SPECIFICATIONS - REAR SUSPENSION ................... 2-28
FEED CIRCUIT RESISTANCE TEST - DIAGNOSIS AND TESTING ..............8F-35
FEED CIRCUIT TEST - DIAGNOSIS AND TESTING ........................... 8F-36
FENDER - INSTALLATION, FRONT ........23-52
FENDER - REMOVAL, FRONT ...........23-51
FFV REPLACEMENT PARTS - DESCRIPTION ........................ 14-2
FILL - DIAGNOSIS AND TESTING, VEHICLE DOES NOT .................. 25-17
FILL DOOR - INSTALLATION, FUEL .......23-52
FILL DOOR - REMOVAL, FUEL ..........23-52
FILL DOOR BLOCKER LATCH - INSTALLATION, FUEL .................23-53
FILL DOOR BLOCKER LATCH - REMOVAL, FUEL ..................... 23-53
FILL DOOR BLOCKER LATCH STRIKER - INSTALLATION, FUEL .................23-53
FILL DOOR BLOCKER LATCH STRIKER - REMOVAL, FUEL ..................... 23-53
FILL DOOR BLOCKER LOCKOUT LINK - INSTALLATION, FUEL .................23-54
FILL DOOR BLOCKER LOCKOUT LINK - REMOVAL, FUEL ..................... 23-54
FILL/CHECK LOCATIONS - DESCRIPTION, FLUID ...............................0-7
FILLER CAP - DESCRIPTION, FUEL .......25-13
FILLER CAP - OPERATION, FUEL ........25-13
FILLER NECK SEAL - DIAGNOSIS AND TESTING, RADIATOR CAP TO ............7-28
FILLER TUBE - INSTALLATION, FUEL TANK .............................. 14-17
FILLER TUBE - REMOVAL, FUEL TANK ....14-16
FILLING - STANDARD PROCEDURE, COOLING SYSTEM .....................7-4
FILLING, STANDARD PROCEDURE - REAR HEATER CORE .................24-102
FILTER - DESCRIPTION, AIR ............24-42
FILTER - DESCRIPTION, OIL .............9-54
FILTER - INSTALLATION, AIR ...........24-43
FILTER - INSTALLATION, INLET ..........14-17
FILTER - INSTALLATION, OIL .......9-141,9-54
FILTER - REMOVAL, AIR ...............24-42
FILTER - REMOVAL, INLET .............14-17
FILTER - REMOVAL, OIL ...........9-141,9-54
12 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

FOLD-IN-FLOOR - REMOVAL, SEATCUSHION COVER/FOAM - THIRD ROW . . . 23-159
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION COVER/FOAM -SECOND
ROW ............................. 23-136
FOLD-IN-FLOOR - REMOVAL, SEAT CUSHION SIDE SHIELD - SECOND
ROW ............................. 23-138
FOLD-IN-FLOOR - REMOVAL, SEAT GAS STRUT - SECOND ROW ...............23-138
FOLD-IN-FLOOR - REMOVAL, SEAT PROP ROD - SECOND ROW ................23-139
FOLD-IN-FLOOR - REMOVAL, SECOND ROW FLOOR TUB CARPET INSERT .......23-98
FOLD-IN-FLOOR - REMOVAL, SIDE SHIELD CUP HOLDER ................23-160
FOLD-IN-FLOOR - REMOVAL, WITH NVLD .............................. 25-20
FOLD-IN-FLOOR - SPECIFICATIONS, WELD LOCATIONS ................... 23-350
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, BODY SEALING
LOCATIONS ........................ 23-209
FOLD-IN-FLOOR ONLY - SPECIFICATIONS, STRUCTURAL
ADHESIVE LOCATIONS ...............23-228
FOLD-IN-FLOOR SEATING - INSTALLATION .................... 5-68,5-75
FOLD-IN-FLOOR SEATING - INSTALLATION, FWD ................... 2-45
FOLD-IN-FLOOR SEATING - REMOVAL . 5-66,5-72
FOLD-IN-FLOOR SEATING - REMOVAL, FWD................................ 2-45
FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS, FRAME DIMENSIONS .....13-11
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FORWARD ............23-137
FOLDING MECHANISM -SECOND ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FORWARD ................23-137
FORM-IN-PLACE GASKETS AND SEALERS, STANDARD PROCEDURE . . . 9-11,9-86
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - INSTALLATION,
SEAT RECLINER/FOLD ................23-160
FORWARD MECHANISM -THIRD ROW -FOLD-IN-FLOOR - REMOVAL, SEAT
RECLINER/FOLD .................... 23-160
FRAME - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT BACK ....23-134
FRAME - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT BACK ........23-134
FRAME - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACK ..........23-157
FRAME - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACK ..............23-156
FRAME DIMENSIONS - FOLD-IN-FLOOR SEATS ONLY - SPECIFICATIONS .........13-11
FRAME DIMENSIONS - SPECIFICATIONS . . . 13-6
FREE MODULE - INSTALLATION, HANDS . . . 8T-3
FREE MODULE - REMOVAL, HANDS .......8T-3
FRONT - DESCRIPTION, HALF SHAFT .......3-1
FRONT - DESCRIPTION, PLUMBING ......24-65
FRONT - INSTALLATION, BUSHING - LEAF SPRING ........................ 2-30
FRONT - INSTALLATION, CRANKSHAFT OIL SEAL ....................... 9-130,9-42
FRONT - INSTALLATION, HALF SHAFT ......3-4
FRONT - INSTALLATION, SEAT BELT & RETRACTOR - OUTBOARD .............8O-39
FRONT - INSTALLATION, SPRING MOUNTS ............................ 2-43
FRONT - INSTALLATION, WHEEL MOUNTING STUDS ................... 22-21
FRONT - OPERATION, PLUMBING ........24-65
FRONT - REMOVAL, BUSHING - LEAF SPRING ............................. 2-29
FRONT - REMOVAL, CRANKSHAFT OIL SEAL .......................... 9-130,9-41
FRONT - REMOVAL, HALF SHAFT ..........3-2
FRONT - REMOVAL, SEAT BELT & RETRACTOR - OUTBOARD .............8O-38
FRONT - REMOVAL, SPRING MOUNTS .....2-42
FRONT - REMOVAL, WHEEL MOUNTING STUDS ............................. 22-21
FRONT - SPECIFICATIONS, HALF SHAFT ....3-6FRONT A/C EXPANSION VALVE,
DIAGNOSIS AND TESTING .............24-82
FRONT BLOWER MOTOR, DIAGNOSIS AND TESTING ....................... 24-46
FRONT BLOWER MOTOR RESISTOR BLOCK, DIAGNOSIS AND TESTING .......24-25
FRONT BRAKE ROTOR - INSTALLATION ....5-59
FRONT BRAKE ROTOR - REMOVAL .......5-59
FRONT BUMPER REINFORCEMENT - INSTALLATION ........................ 13-3
FRONT BUMPER REINFORCEMENT - REMOVAL ........................... 13-3
FRONT CABLE - INSTALLATION, PARKING BRAKE LEVER ................5-77
FRONT CABLE - REMOVAL, PARKING BRAKE LEVER ........................ 5-77
FRONT CENTER BEZEL OUTLETS, INSTALLATION ....................... 24-45
FRONT CENTER BEZEL OUTLETS, REMOVAL .......................... 24-44
FRONT CONTROL MODULE - DESCRIPTION ........................ 8E-7
FRONT CONTROL MODULE - OPERATION . . 8E-7
FRONT CONTROL MODULE, DIAGNOSIS AND TESTING ........................ 8E-7
FRONT CRADLE CROSSMEMBER - DESCRIPTION ....................... 13-14
FRONT CRADLE CROSSMEMBER THREAD REPAIR - DESCRIPTION ........13-14
FRONT CROSSMEMBER MOUNT BUSHINGS - INSTALLATION ............13-17
FRONT CROSSMEMBER MOUNT BUSHINGS - REMOVAL .................13-17
FRONT DEMISTER OUTLETS, INSTALLATION ....................... 24-45
FRONT DEMISTER OUTLETS, REMOVAL . . . 24-44
FRONT DISC BRAKE CALIPER ADAPTER - INSTALLATION ...................... 5-31
FRONT DISC BRAKE CALIPER ADAPTER - REMOVAL .......................... 5-31
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-27
FRONT DISC BRAKE CALIPER (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-24
FRONT DISC BRAKE CALIPER (TRW BRAKES) - INSTALLATION ...............5-27
FRONT DISC BRAKE CALIPER (TRW BRAKES) - REMOVAL .................. 5-24
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
INSTALLATION ........................ 5-16
FRONT DISC BRAKE SHOES (CONTINENTAL TEVES BRAKES) -
REMOVAL ........................... 5-15
FRONT DISC BRAKE SHOES (TRW BRAKES) - INSTALLATION ...............5-17
FRONT DISC BRAKE SHOES (TRW BRAKES) - REMOVAL .................. 5-15
FRONT DOOR GLASS RUN WEATHERSTRIP - INSTALLATION .......23-166
FRONT DOOR GLASS RUN WEATHERSTRIP - REMOVAL ...........23-166
FRONT DOOR INNER BELT MOLDING - INSTALLATION ...................... 23-168
FRONT DOOR INNER BELT MOLDING - REMOVAL ......................... 23-168
FRONT DOOR OUTER BELT MOLDING - INSTALLATION ...................... 23-167
FRONT DOOR OUTER BELT MOLDING - REMOVAL ......................... 23-167
FRONT DOOR WEATHERSTRIP - INSTALLATION ...................... 23-168
FRONT DOOR WEATHERSTRIP - REMOVAL ......................... 23-168
FRONT FASCIA - INSTALLATION ..........13-1
FRONT FASCIA - REMOVAL ..............13-1
FRONT FENDER - INSTALLATION ........23-52
FRONT FENDER - REMOVAL ............23-51
FRONT FOG LAMP - DIAGNOSIS AND TESTING ............................ 8L-7
FRONT FOG LAMP - INSTALLATION .......8L-8
FRONT FOG LAMP - REMOVAL ...........8L-8
FRONT FOG LAMP UNIT ALIGNMENT - EXPORT - STANDARD PROCEDURE .......8L-9
FRONT FOG LAMP UNIT ALIGNMENT - STANDARD PROCEDURE ................8L-9FRONT HEATER CORE, INSTALLATION
....24-86
FRONT HEATER CORE, REMOVAL ........24-85
FRONT HEATER CORE TUBES, INSTALLATION ....................... 24-85
FRONT HEATER CORE TUBES, REMOVAL . . 24-84
FRONT INBOARD - INSTALLATION, SEAT BELT BUCKLE ....................... 8O-35
FRONT INBOARD - REMOVAL, SEAT BELT BUCKLE ....................... 8O-35
FRONT MOUNT - INSTALLATION ....9-134,9-50
FRONT MOUNT - REMOVAL ........9-134,9-50
FRONT SEAT - INSTALLATION ..........23-110
FRONT SEAT - REMOVAL .............23-108
FRONT SEAT BACK - INSTALLATION .....23-111
FRONT SEAT BACK - REMOVAL ........23-111
FRONT SEAT BACK ASSIST STRAP - INSTALLATION ...................... 23-112
FRONT SEAT BACK ASSIST STRAP - REMOVAL ......................... 23-112
FRONT SEAT BACK COVER - INSTALLATION ...................... 23-116
FRONT SEAT BACK COVER - REMOVAL . . 23-113
FRONT SEAT BACK PANEL - INSTALLATION ...................... 23-113
FRONT SEAT BACK PANEL - REMOVAL . . 23-112
FRONT SEAT CUSHION - INSTALLATION . . 23-118
FRONT SEAT CUSHION - OCS - INSTALLATION ...................... 23-120
FRONT SEAT CUSHION - OCS - REMOVAL ........................... 23-119
FRONT SEAT CUSHION - REMOVAL .....23-117
FRONT SEAT CUSHION SIDE COVER - INSTALLATION ...................... 23-121
FRONT SEAT CUSHION SIDE COVER - OCS - INSTALLATION ................23-122
FRONT SEAT CUSHION SIDE COVER - OCS - REMOVAL .................... 23-121
FRONT SEAT CUSHION SIDE COVER - REMOVAL ......................... 23-120
FRONT SEAT RISER - MANUAL - OCS - INSTALLATION ...................... 23-123
FRONT SEAT RISER - MANUAL - OCS - REMOVAL ......................... 23-123
FRONT SEAT TRACK - REAR COVER - INSTALLATION ...................... 23-128
FRONT SEAT TRACK - REAR COVER - REMOVAL ......................... 23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - INSTALLATION ...............23-128
FRONT SEAT TRACK ADJUSTER/MANUAL - OCS - REMOVAL ................... 23-126
FRONT SEAT TRACK ADJUSTER/POWER - OCS - INSTALLATION ...............23-125
FRONT SEAT TRACK ADJUSTER/POWER - OCS - REMOVAL ................... 23-124
FRONT SEAT TRACK MANUAL ADJUSTER - INSTALLATION ...........23-126
FRONT SEAT TRACK MANUAL ADJUSTER - REMOVAL ...............23-125
FRONT SEAT TRACK POWER ADJUSTER - INSTALLATION .................... 23-124
FRONT SEAT TRACK POWER ADJUSTER - REMOVAL ........................ 23-124
FRONT SEAT TRACK REAR COVER - OCS - INSTALLATION .................... 23-129
FRONT SEAT TRACK REAR COVER - OCS - REMOVAL ........................ 23-129
FRONT SUSPENSION - DESCRIPTION ......2-2
FRONT SUSPENSION - OPERATION ........2-2
FRONT SUSPENSION FASTENER TORQUE, SPECIFICATIONS ...............2-3
FRONT SUSPENSION, SPECIAL TOOLS .....2-3
FRONT WHEEL SPEED SENSOR - INSTALLATION ........................ 5-92
FRONT WHEEL SPEED SENSOR - REMOVAL ........................... 5-91
FRONT WHEELHOUSE SPLASH SHIELD - INSTALLATION ....................... 23-57
FRONT WHEELHOUSE SPLASH SHIELD - REMOVAL .......................... 23-57
FRONT WIPER ARM ALIGNMENT - STANDARD PROCEDURE ...............8R-9
FRONT WIPER ARMS - INSTALLATION ....8R-9
FRONT WIPER ARMS - REMOVAL ........8R-9
FRONT WIPER MOTOR - INSTALLATION . . 8R-10
FRONT WIPER MOTOR - REMOVAL .......8R-9
FRONT WIPER SYSTEM - DIAGNOSIS AND TESTING ........................ 8R-2
14 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

SLEEVE - THIRD ROW - FOLD-IN-FLOOR- INSTALLATION, HEADREST ...........23-153
SLEEVE - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, HEADREST ..............23-152
SLIDING DOOR - INSTALLATION .........23-29
SLIDING DOOR - REMOVAL ............23-29
SLIDING DOOR ADJUSTMENT, STANDARD PROCEDURE - POWER ......8N-49
SLIDING DOOR ADJUSTMENTS, ADJUSTMENTS ...................... 23-30
SLIDING DOOR CONTROL MODULE - DESCRIPTION ....................... 8E-18
SLIDING DOOR CONTROL MODULE - OPERATION ......................... 8E-18
SLIDING DOOR CONTROL MODULE, DIAGNOSIS AND TESTING .............8E-18
SLIDING DOOR GLASS - INSTALLATION . . 23-163
SLIDING DOOR GLASS - REMOVAL .....23-163
SLIDING DOOR LEARN CYCLE, STANDARD PROCEDURE - POWER ......8N-48
SLIDING DOOR LOCK MOTOR - INSTALLATION ...................... 8N-25
SLIDING DOOR LOCK MOTOR - REMOVAL .......................... 8N-25
SLIDING DOOR MOTOR - DESCRIPTION . . 8N-51
SLIDING DOOR MOTOR - INSTALLATION . . 8N-51
SLIDING DOOR MOTOR - OPERATION ....8N-51
SLIDING DOOR MOTOR - REMOVAL .....8N-51
SLIDING DOOR SILL PLATE - INSTALLATION ....................... 23-99
SLIDING DOOR SILL PLATE - REMOVAL ....23-98
SLIDING DOOR STOP BUMPER BEZEL - INSTALLATION ....................... 23-25
SLIDING DOOR STOP BUMPER BEZEL - REMOVAL .......................... 23-25
SLIDING DOOR SYSTEM - DESCRIPTION, POWER ............................ 8N-40
SLIDING DOOR SYSTEM - OPERATION, POWER ............................ 8N-41
SLIDING DOOR SYSTEM, DIAGNOSIS AND TESTING - POWER ...............8N-42
SLIDING DOOR WEATHERSTRIP - INSTALLATION ...................... 23-168
SLIDING DOOR WEATHERSTRIP - REMOVAL ......................... 23-168
SOCKET - INSTALLATION, STABILIZER ....23-33
SOCKET - REMOVAL, STABILIZER .......23-33
SOLENOID - DESCRIPTION, EVAP/PURGE . 25-13
SOLENOID - DESCRIPTION, SHIFT INTERLOCK .................. 21-113,21-264
SOLENOID - DIAGNOSIS AND TESTING, BRAKE/TRANSMISSION SHIFT
INTERLOCK .................. 21-115,21-266
SOLENOID - INSTALLATION, EVAP/ PURGE ............................. 25-13
SOLENOID - INSTALLATION, SHIFT INTERLOCK .................. 21-116,21-267
SOLENOID - OPERATION, EVAP/PURGE . . . 25-13
SOLENOID - OPERATION, SHIFT INTERLOCK .................. 21-114,21-265
SOLENOID - REMOVAL, EVAP/PURGE .....25-13
SOLENOID - REMOVAL, SHIFT INTERLOCK .................. 21-115,21-266
SOLENOID/PRESSURE SWITCH ASSY - DESCRIPTION ................ 21-117,21-268
SOLENOID/PRESSURE SWITCH ASSY - INSTALLATION ................ 21-119,21-270
SOLENOID/PRESSURE SWITCH ASSY - OPERATION .................. 21-118,21-268
SOLENOID/PRESSURE SWITCH ASSY - REMOVAL ................... 21-118,21-269
SPARE TIRE (TEMPORARY) - DESCRIPTION ....................... 22-14
SPARK PLUG CABLE - DESCRIPTION .....8I-10
SPARK PLUG CABLE RESISTANCE, SPECIFICATIONS ...................... 8I-2
SPARK PLUG, SPECIFICATIONS ...........8I-2
SPEAKER, DIAGNOSIS AND TESTING .....8A-18
SPEED CONTROL - DESCRIPTION ........8P-1
SPEED CONTROL (4 SPEED EATX ONLY) - OPERATION, INTERACTIVE .............8P-2
SPEED OPERATION - STANDARD PROCEDURE, TIRE PRESSURE FOR
HIGH .............................. 22-17
SPEED SENSOR - AWD - INSTALLATION, REAR WHEEL ........................ 5-92
SPEED SENSOR - AWD - REMOVAL, REAR WHEEL ........................ 5-92SPEED SENSOR - DESCRIPTION, ENGINE . 14-30
SPEED SENSOR - FWD - INSTALLATION,
REAR WHEEL ........................ 5-93
SPEED SENSOR - FWD - REMOVAL, REAR WHEEL ........................ 5-93
SPEED SENSOR - INPUT - DESCRIPTION ................ 21-120,21-271
SPEED SENSOR - INPUT - INSTALLATION ................ 21-121,21-272
SPEED SENSOR - INPUT - OPERATION . . 21-120, 21-271
SPEED SENSOR - INPUT - REMOVAL . . . 21-121, 21-272
SPEED SENSOR - INSTALLATION, FRONT WHEEL ............................. 5-92
SPEED SENSOR - OPERATION, ENGINE . . . 14-30
SPEED SENSOR - OUTPUT - DESCRIPTION ................ 21-122,21-273
SPEED SENSOR - OUTPUT - INSTALLATION ................ 21-123,21-274
SPEED SENSOR - OUTPUT - OPERATION .................. 21-122,21-273
SPEED SENSOR - OUTPUT - REMOVAL . . 21-123, 21-274
SPEED SENSOR - REMOVAL, FRONT WHEEL ............................. 5-91
SPEED SENSOR AIR GAP, SPECIFICATIONS - WHEEL ..............5-91
SPIRAL PLATE BATTERY CHARGING, STANDARD PROCEDURE ...............8F-10
SPLASH SHIELD - INSTALLATION, FRONT WHEELHOUSE .................23-57
SPLASH SHIELD - REMOVAL, FRONT WHEELHOUSE ....................... 23-57
SPLICE INFORMATION - DESCRIPTION, CONNECTOR, GROUND ..............8W-01-7
SPLICING - STANDARD PROCEDURE, WIRE ...........................8W -01-15
SPLIT - INSTALLATION, BENCH SEAT RISER - 50/50 ...................... 23-145
SPLIT - REMOVAL, BENCH SEAT RISER - 50/50 ............................. 23-145
SPLIT, BENCH - INSTALLATION, SEAT BACK HINGE COVERS - QUAD BUCKET,
50/50 ............................. 23-146
SPLIT, BENCH - INSTALLATION, SEAT CUSHION COVER - QUAD BUCKET,
50/50 ............................. 23-144
SPLIT, BENCH - REMOVAL, SEAT BACK HINGE COVERS - QUAD BUCKET, 50/50 . . 23-146
SPLIT, BENCH - REMOVAL, SEAT CUSHION COVER - QUAD BUCKET,
50/50 ............................. 23-144
SPRING - AWD - INSTALLATION ..........2-39
SPRING - AWD - REMOVAL .............2-38
SPRING - CARGO - INSTALLATION ........2-40
SPRING - CARGO - REMOVAL ...........2-40
SPRING - FWD - INSTALLATION ..........2-42
SPRING - FWD - REMOVAL .............2-40
SPRING ASSEMBLY - INSTALLATION, QUAD BUCKET SEAT SIDE SHIELD/CUP
HOLDER - FLAP ..................... 23-151
SPRING ASSEMBLY - REMOVAL, QUAD BUCKET SEAT SIDE SHIELD/CUP
HOLDER - FLAP ..................... 23-151
SPRING FRONT - INSTALLATION, BUSHING - LEAF ...................... 2-30
SPRING FRONT - REMOVAL, BUSHING - LEAF ............................... 2-29
SPRING MOUNTS - FRONT - INSTALLATION ........................ 2-43
SPRING MOUNTS - FRONT - REMOVAL ....2-42
SPRING MOUNTS - REAR - INSTALLATION ........................ 2-43
SPRING MOUNTS - REAR - REMOVAL .....2-43
SPRING SHACKLE - INSTALLATION .......2-44
SPRING SHACKLE - REMOVAL ...........2-44
SPRINGS - DESCRIPTION, VALVE ........9-109
SPRINGS - OPERATION, VALVE .........9-109
SPROCKET - INSTALLATION, CRANKSHAFT ................... 9-160,9-67
SPROCKET - INSTALLATION, TIMING CHAIN AND CAMSHAFT ...............9-160
SPROCKET - REMOVAL, CRANKSHAFT . . . 9-159,
9-66
SPROCKET - REMOVAL, TIMING CHAIN AND CAMSHAFT ..................... 9-159SPROCKETS - INSTALLATION,
CAMSHAFT .......................... 9-67
SPROCKETS - REMOVAL, CAMSHAFT ......9-66
STABILIZER - INSTALLATION ...........23-33
STABILIZER - REMOVAL ...............23-33
STABILIZER BAR - DESCRIPTION .....2-16,2-44
STABILIZER BAR - INSPECTION ..........2-17
STABILIZER BAR - INSTALLATION ........2-17
STABILIZER BAR - OPERATION .......2-16,2-44
STABILIZER BAR - REMOVAL ............2-17
STABILIZER BAR CUSHION - INSTALLATION .........................2-4
STABILIZER BAR CUSHION - REMOVAL .....2-4
STABILIZER SOCKET - INSTALLATION ....23-33
STABILIZER SOCKET - REMOVAL ........23-33
STAKING - STANDARD PROCEDURE, HEAT ............................... 23-9
STANDARD 4 CYLINDER - DESCRIPTION . . . 8I-9
STARTER, SPECIFICATIONS .............8F-37
STARTING - DESCRIPTION .............8F-31
STARTING - OPERATION ...............8F-31
STARTING - STANDARD PROCEDURE, JUMP ............................... 0-25
STARTING SYSTEM TEST - DIAGNOSIS AND TESTING ....................... 8F-31
STATE DISPLAY TEST MODE, OPERATION - DRB III T................ 25-10
STEERING - DIAGNOSIS AND TESTING, SUSPENSION .......................... 2-50
STEERING BELT TENSION - STANDARD PROCEDURE, CHECKING POWER ..........7-8
STEERING COLUMN - DESCRIPTION .....19-10
STEERING COLUMN - DIAGNOSIS AND TESTING ........................... 19-11
STEERING COLUMN COVER - INSTALLATION, LOWER ................23-74
STEERING COLUMN COVER - INSTALLATION, OVER .................23-76
STEERING COLUMN COVER - REMOVAL, LOWER ............................ 23-74
STEERING COLUMN COVER - REMOVAL, OVER .............................. 23-76
STEERING FASTENER TORQUE, SPECIFICATIONS - POWER ..............19-9
STEERING FLUID LEVEL CHECKING - STANDARD PROCEDURE, POWER .......19-44
STEERING GEAR, SPECIAL TOOLS - POWER ............................ 19-34
STEERING KNUCKLE - INSPECTION ........2-9
STEERING KNUCKLE - INSTALLATION ......2-9
STEERING KNUCKLE - REMOVAL ..........2-7
STEERING PUMP INITIAL OPERATION - STANDARD PROCEDURE, POWER .......19-37
STEERING PUMP, SPECIAL TOOLS - POWER ............................ 19-44
STEERING, SPECIAL TOOLS - POWER .....19-9
STEERING SYSTEM - DESCRIPTION, POWER ............................. 19-1
STEERING SYSTEM - OPERATION, POWER ............................. 19-1
STEERING SYSTEM DIAGNOSIS CHARTS - DIAGNOSIS AND TESTING .............19-3
STEERING SYSTEM FLOW AND PRESSURE TEST - DIAGNOSIS AND
TESTING, POWER ..................... 19-1
STEERING WHEEL - INSTALLATION ......19-24
STEERING WHEEL - REMOVAL ..........19-23
STEM SEALS - DESCRIPTION, VALVE .....9-114
STEM SEALS - INSTALLATION, VALVE ....9-115
STEM SEALS - REMOVAL, VALVE ........9-115
STOP BUMPER - INSTALLATION .........23-25
STOP BUMPER - REMOVAL ............23-25
STOP BUMPER BEZEL - INSTALLATION, SLIDING DOOR ...................... 23-25
STOP BUMPER BEZEL - REMOVAL, SLIDING DOOR ...................... 23-25
STOP LAMP - INSTALLATION, CENTER HIGH MOUNTED ...................... 8L-6
STOP LAMP - REMOVAL, CENTER HIGH MOUNTED ........................... 8L-6
STOP LAMP UNIT - INSTALLATION, CENTER HIGH MOUNTED ...............8L-6
STOP LAMP UNIT - REMOVAL, CENTER HIGH MOUNTED ...................... 8L-6
STORAGE BIN - INSTALLATION, UNDER SEAT ............................. 23-149
STORAGE BIN - REMOVAL, UNDER SEAT . 23-149
30 INDEXRS
Description Group-Page Description Group-Page Description Group-Page

STORAGE BIN GUIDE - INSTALLATION,UNDER SEAT ....................... 23-150
STORAGE BIN GUIDE - REMOVAL, UNDER SEAT ....................... 23-150
STORAGE BIN LOCK/LATCH - INSTALLATION, UNDER SEAT ..........23-150
STORAGE BIN LOCK/LATCH - REMOVAL, UNDER SEAT ....................... 23-150
STRAP - INSTALLATION, CHECK .........23-15
STRAP - INSTALLATION, FRONT SEAT BACK ASSIST ...................... 23-112
STRAP - REMOVAL, CHECK ............23-15
STRAP - REMOVAL, FRONT SEAT BACK ASSIST ........................... 23-112
STRAP - THIRD ROW - FOLD-IN-FLOOR - INSTALLATION, SEAT BACKSTOW .....23-158
STRAP - THIRD ROW - FOLD-IN-FLOOR - REMOVAL, SEAT BACKSTOW .........23-158
STRIKER - INSTALLATION, CENTER ......23-28
STRIKER - INSTALLATION, FUEL FILL DOOR BLOCKER LATCH ...............23-53
STRIKER - INSTALLATION, GLOVE BOX LATCH ............................. 23-66
STRIKER - INSTALLATION, HOLD OPEN LATCH ............................. 23-26
STRIKER - INSTALLATION, LATCH . . 23-19,23-42, 23-64
STRIKER - INSTALLATION, REAR LATCH . . 23-29
STRIKER - REMOVAL, CENTER ..........23-28
STRIKER - REMOVAL, FUEL FILL DOOR BLOCKER LATCH ..................... 23-53
STRIKER - REMOVAL, GLOVE BOX LATCH ............................. 23-66
STRIKER - REMOVAL, HOLD OPEN LATCH ............................. 23-26
STRIKER - REMOVAL, LATCH . 23-19,23-41,23-64
STRIKER - REMOVAL, REAR LATCH ......23-29
STRIPPED THREAD REPAIR - STANDARD PROCEDURE, MANIFOLD ..............9-147
STRUCTURAL ADHESIVE LOCATIONS - FOLD-IN-FLOOR ONLY -
SPECIFICATIONS .................... 23-228
STRUCTURAL ADHESIVE LOCATIONS - SPECIFICATIONS .................... 23-218
STRUCTURAL COLLAR - INSTALLATION ....9-49
STRUCTURAL COLLAR - REMOVAL .......9-49
STRUT - SECOND ROW - FOLD-IN- FLOOR - INSTALLATION, SEAT GAS .....23-139
STRUT - SECOND ROW - FOLD-IN- FLOOR - REMOVAL, SEAT GAS .........23-138
STRUT ASSEMBLY - ASSEMBLY ..........2-23
STRUT ASSEMBLY - DESCRIPTION .......2-19
STRUT ASSEMBLY - DIAGNOSIS AND TESTING ............................ 2-20
STRUT ASSEMBLY - DISASSEMBLY .......2-21
STRUT ASSEMBLY - INSTALLATION .......2-25
STRUT ASSEMBLY - OPERATION .........2-19
STRUT ASSEMBLY - REMOVAL ...........2-20
STUDS - FRONT - INSTALLATION, WHEEL MOUNTING ................... 22-21
STUDS - FRONT - REMOVAL, WHEEL MOUNTING ......................... 22-21
STUDS - REAR - INSTALLATION, WHEEL MOUNTING ......................... 22-22
STUDS - REAR - REMOVAL, WHEEL MOUNTING ......................... 22-22
SUCTION LINE - INSTALLATION . . . 24-107,24-97
SUCTION LINE - REMOVAL .......24-106,24-96
SUN VISOR - INSTALLATION ...........23-99
SUN VISOR - REMOVAL ...............23-99
SUN VISOR SUPPORT - INSTALLATION . . . 23-99
SUN VISOR SUPPORT - REMOVAL .......23-99
SUNROOF - DESCRIPTION ............23-169
SUNROOF ASSEMBLY - INSTALLATION . . 23-173
SUNROOF ASSEMBLY - REMOVAL ......23-173
SUNROOF DIAGNOSIS AND TESTING, DIAGNOSIS AND TESTING ............23-169
SUNROOF GLASS PANEL ADJUSTMENT, ADJUSTMENTS ..................... 23-173
SUNROOF MOTOR - INSTALLATION .....23-174
SUNROOF MOTOR - REMOVAL .........23-174
SUNROOF SWITCH - INSTALLATION .....23-176
SUNROOF SWITCH - REMOVAL ........23-176
SUNSHADE - INSTALLATION ...........23-173
SUNSHADE - REMOVAL ..............23-173
SUPPLEMENTAL CABIN HEATER, DIAGNOSIS AND TESTING ............24-114SUPPLY - PCM OUTPUT - OPERATION, 5
VOLT .............................. 8E-15
SUPPORT - INSTALLATION, LUMBAR ....23-150
SUPPORT - INSTALLATION, SUN VISOR . . . 23-99
SUPPORT - REMOVAL, LUMBAR .......23-150
SUPPORT - REMOVAL, SUN VISOR ......23-99
SUPPORT CYLINDER - INSTALLATION ....23-43
SUPPORT CYLINDER - REMOVAL ........23-42
SUPPORT PLATE - DRUM BRAKE - INSTALLATION ........................ 5-61
SUPPORT PLATE - DRUM BRAKE - REMOVAL ........................... 5-61
SUPPRESSION COMPONENTS - DESCRIPTION, RADIO NOISE ...........8A-15
SUPPRESSION COMPONENTS - OPERATION, RADIO NOISE .............8A-15
SURFACE PREPARATION - STANDARD PROCEDURE, ENGINE GASKET .......9-11,9-87
SUSPENSION - DESCRIPTION, FRONT ......2-2
SUSPENSION - DESCRIPTION, REAR ......2-26
SUSPENSION - OPERATION, FRONT ........2-2
SUSPENSION AND STEERING - DIAGNOSIS AND TESTING ..............2-50
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - FRONT ................2-3
SUSPENSION FASTENER TORQUE, SPECIFICATIONS - REAR ................2-28
SUSPENSION, SPECIAL TOOLS - FRONT ....2-3
SUSPENSION, SPECIAL TOOLS - REAR ....2-28
SWITCH - DESCRIPTION .................8P-5
SWITCH - DESCRIPTION, B-PILLAR ......8N-52
SWITCH - DESCRIPTION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - DESCRIPTION, BRAKE LAMP ....8L-4
SWITCH - DESCRIPTION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - DESCRIPTION, FULL OPEN ....8N-11,
8N-52
SWITCH - DESCRIPTION, HEATED SEAT . . . 8G-8
SWITCH - DESCRIPTION, HORN ..........8H-4
SWITCH - DESCRIPTION, MEMORY ......8N-36
SWITCH - DESCRIPTION, OIL PRESSURE . 9-144
SWITCH - DESCRIPTION, REAR WINDOW DEFOGGER .................. 8G-4
SWITCH - DESCRIPTION, REAR WIPER/WASHER ..................... 8R-10
SWITCH - DESCRIPTION, SEAT .........8N-34
SWITCH - DIAGNOSIS AND TESTING, BRAKE LAMP ........................ 8L-4
SWITCH - DIAGNOSIS AND TESTING, FAILED PARK ........................ 8R-2
SWITCH - DIAGNOSIS AND TESTING, FRONT WIPER/WASHER ................8R-2
SWITCH - DIAGNOSIS AND TESTING, HEADLAMP ......................... 8L-13
SWITCH - DIAGNOSIS AND TESTING, MULTI-FUNCTION .................... 8L-18
SWITCH - DIAGNOSIS AND TESTING, TRACTION CONTROL ................... 5-94
SWITCH - EXPORT - DESCRIPTION, DOOR CYLINDER LOCK ...............8N-22
SWITCH - EXPORT - DESCRIPTION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - INSTALLATION, HOOD AJAR ......................... 8Q-3
SWITCH - EXPORT - INSTALLATION, POWER FOLDAWAY MIRROR ...........8N-30
SWITCH - EXPORT - OPERATION, DOOR CYLINDER LOCK ..................... 8N-22
SWITCH - EXPORT - OPERATION, POWER FOLDAWAY MIRROR ...........8N-29
SWITCH - EXPORT - REMOVAL, HOOD AJAR ............................... 8Q-3
SWITCH - EXPORT - REMOVAL, POWER FOLDAWAY MIRROR .................. 8N-29
SWITCH - INSTALLATION ...............8P-6
SWITCH - INSTALLATION, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - INSTALLATION, B-PILLAR .....8N-52
SWITCH - INSTALLATION, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - INSTALLATION, BRAKE LAMP . . . 8L-5
SWITCH - INSTALLATION, CENTER CONSOLE LAMP ..................... 8L-21
SWITCH - INSTALLATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - INSTALLATION, FULL OPEN ....8N-11 SWITCH - INSTALLATION, GLOVE BOX
LAMP .............................. 8L-22
SWITCH - INSTALLATION, HEADLAMP ....8L-13
SWITCH - INSTALLATION, IGNITION ......19-19
SWITCH - INSTALLATION, MULTI- FUNCTION .......................... 8L-18
SWITCH - INSTALLATION, OIL PRESSURE ..................... 9-144,9-56
SWITCH - INSTALLATION, SUNROOF ....23-176
SWITCH - INSTALLATION, TRACTION CONTROL ........................... 5-95
SWITCH - INSTALLATION, WASHER FLUID LEVEL ........................ 8R-11
SWITCH - OPERATION .................8P-5
SWITCH - OPERATION, B-PILLAR ........8N-52
SWITCH - OPERATION, BRAKE FLUID LEVEL .............................. 5-10
SWITCH - OPERATION, BRAKE LAMP ......8L-4
SWITCH - OPERATION, EXTERIOR HANDLE ........................... 8N-10
SWITCH - OPERATION, FULL OPEN . 8N-11,8N-52
SWITCH - OPERATION, HEATED SEAT .....8G-9
SWITCH - OPERATION, MEMORY ........8N-36
SWITCH - OPERATION, OIL PRESSURE . . . 9-144
SWITCH - OPERATION, REAR WINDOW DEFOGGER .......................... 8G-4
SWITCH - OPERATION, REAR WIPER/ WASHER ........................... 8R-11
SWITCH - OPERATION, SEAT ...........8N-34
SWITCH - REMOVAL .................... 8P-5
SWITCH - REMOVAL, ADJUSTABLE PEDALS ............................. 5-11
SWITCH - REMOVAL, B-PILLAR .........8N-52
SWITCH - REMOVAL, BRAKE FLUID LEVEL .............................. 5-11
SWITCH - REMOVAL, BRAKE LAMP .......8L-5
SWITCH - REMOVAL, CENTER CONSOLE LAMP .............................. 8L-21
SWITCH - REMOVAL, EXTERIOR HANDLE . 8N-10
SWITCH - REMOVAL, FULL OPEN .......8N-11
SWITCH - REMOVAL, GLOVE BOX LAMP . . 8L-22
SWITCH - REMOVAL, HEADLAMP ........8L-13
SWITCH - REMOVAL, IGNITION .........19-17
SWITCH - REMOVAL, MULTI-FUNCTION . . . 8L-18
SWITCH - REMOVAL, OIL PRESSURE ....9-144,
9-56
SWITCH - REMOVAL, SUNROOF ........23-176
SWITCH - REMOVAL, TRACTION CONTROL ........................... 5-95
SWITCH - REMOVAL, WASHER FLUID LEVEL ............................. 8R-11
SWITCH ASSY - DESCRIPTION, SOLENOID/PRESSURE ..........21-117,21-268
SWITCH ASSY - INSTALLATION, SOLENOID/PRESSURE ..........21-119,21-270
SWITCH ASSY - OPERATION, SOLENOID/ PRESSURE .................. 21-118,21-268
SWITCH ASSY - REMOVAL, SOLENOID/ PRESSURE .................. 21-118,21-269
SWITCH, DIAGNOSIS AND TESTING - DOOR LOCK ........................ 8N-23
SWITCH, DIAGNOSIS AND TESTING - DRIVER HEATED SEAT .................8G-9
SWITCH, DIAGNOSIS AND TESTING - DRIVER SEAT ....................... 8N-34
SWITCH, DIAGNOSIS AND TESTING - MEMORY ........................... 8N-37
SWITCH, DIAGNOSIS AND TESTING - REMOTE ........................... 8N-30
SWITCH, DIAGNOSIS AND TESTING - WINDOW ........................... 8N-63
SWITCH, EXPORT - DOOR CYLINDER LOCK .............................. 8N-22
SWITCHES - DESCRIPTION, REMOTE .....8A-16
SWITCHES - OPERATION, REMOTE ......8A-16
SWITCHES, DIAGNOSIS AND TESTING - REMOTE ........................... 8A-16
SYMBOLS - DESCRIPTION, INTERNATIONAL .......................0-1
SYNCHRONIZING CABLE ADJUSTMENT, INSTALLATION ................ 23-105,23-147
TAIL LAMP - INSTALLATION ............8L-19
TAIL LAMP - REMOVAL ................8L-18
TAIL LAMP UNIT - INSTALLATION .......8L-19
TAIL LAMP UNIT - REMOVAL ...........8L-19
TANK - DESCRIPTION, FUEL ............14-12
TANK - OPERATION, FUEL ..............14-12
RS INDEX31
Description Group-Page Description Group-Page Description Group-Page